Tender For As & As And Special Repairs To Building No P-14 Located Inside Naval Dockyard , Viskahapatnam; 2 Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. 3 Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. 4 Demolition of Cement Concrete (un-reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. 5 Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed 6 Taking down Chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m eachbut with shutters (without taking off shutters from the frame) complete all as specified and directed. 7 Taking down Chowkhats or frames not exc 1.5 sq. m each but with shutters (without taking off shutters from the frame complete all as specified and directed. 8 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 9 Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness including cover fillets/snap grid etc complete all as specified and directed. 10 Removing building materials etc. (other than spoil)out side MOD landto a distance of 1.50 km or under, beyond the lead, including loading, unloading and stacking at the destination complete all as directed. 11 Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed. . 12 Excavating over areas, n exc 1.5 m deep and getting out in hard rock complete all as specified and directed. 13 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in hard dense soil complete all as specified and directed. . 14 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. orfor shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc1.5 m in depth and getting out in hard rock complete all as specified and directed. 15 Excavating in trenches, n exc 1.5 m wide and exc 1.5 m but n.exc 3.00 m in depth; for foundation, etc. orfor shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc1.5 m in depth and getting out in hard rock complete all as specified and directed. 16 M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area, complete all as specified and directed. 17 M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per sqm of vertical surface, complete all as specified and directed. (Note: Area of the substructure in contact with backfill shall be measured.) 18 M&L for treating the top surface of filled earth at the rate of 5.00 litres of emulsion per sqm of surface complete all as specified and directed. 19 M&L treating the soil along with external perimeter of building at the rate of 2.25 litres of emulsion per metre of the perimeter wall, complete all as specified and directed. 20 M&L treating the soil under plinth protection at the rate of 5.00 litres of emulsion per Sqm, complete all as specified and directed. 21 M & L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed to a true surface including watering complete all as specified and directed. 22 M&L for PCC 1:4:8 , type D-2, using 40mm graded crushed stoneaggregateas in foundation,filling and mass concrete commplete all as specified and directed. 23 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil commplete all as specified and directed. 24 Removing excavated material (rock) exc.1.50 km but n exc. 5.00km and depositing where directed outside Md land complete all as specified and directed. 25 Removal of surplus soil of distance not exceeding 50 meter and depositing where directed at a level not exceeding 1.5 meter above the starting point complete all as specified and directed.. 26 Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for flat rough finished surface complete all as specified and directed.. 27 M&L for RCC M-30 (Design mix) using 20mm graded crushed stone aggregate asin foundations, including rafts, footings, foundation beams, plinth beams, foundation for columns, etc complete all as specified and directed. 28 Use and waste of formwork to sides of pillars, posts, struts, piers,columns and stanchions for flat fair finished surface complete all as specified and directed. 29 M&L for RCC M-30 (Design mix) using 20mm graded crushed stone aggregate asin columns,pillars etccomplete all as specified and directed.. 30 Use and waste offormwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves ,plinth beam including supports, overhangs, etc. also splays between floors and beams, etccomplete all as specified and directed. 31 M&L for RCC M-30 (Design mix) using 20mm graded crushed stone aggregate asinlintels beams and roof beams etc complete all as specified and directed. 32 Useand waste offormwork to flat surfaces of chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed by Engineer-in-Charge. 33 M&L for RCC M-30 (Design Mix) using 20mm graded stone aggregate as in chajjascomplete all as specified and directed. 34 Use and waste of form work to soffits of suspended slabs such as roof slabs, n. exc. 20cm thick (horizontal or sloping for fair finished concrete surface complete all as specified and directed. 35 M&L for RCC M-30 (Design mix) using 20mm graded crushed stone aggregate asinslabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and the likeetc complete all as specified and directed. 36 Use and waste of formwork to Formwork to fins, louvers, fascia complete all as specified and directed. 37 M & L RCC- M-30 (Design Mix) in fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the like complete all as specified and directed. 38 Use and waste of formwork to staircases with sloping or stepped soffits including risers and stringers (excluding landing) complete all as specified and directed. 39 M & L for RCC- M-30 (Design Mix) in Chullah hoods; stairways (except spiral staircases) including steps (square or spandril), string pieces, carriages, etc., complete, any section straight or winding, but excluding landings; RCC water tanks upto 1500 litres complete all as specified and directed. 40 Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide flat fair finished surface complete all as specified and directed. complete all as specified and directed. 41 S & F Mild steel TMT bars of grade Fe 500D 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. 42 Ditto, as item No.40 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders 43 M&L for Brick work with subclass ‘B’ old size fly ash bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed . 44 M&L for Brick work with subclass ‘B’ old size fly ash bricks, straight or curved on plan exc 6m mean radius in half brick thick walls in, built in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.. 45 M & L for formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter flat fair finished surface complete all as specified and directed. complete all as specified and directed. 46 M & L for rendering 15 mm thick in two coats (10mm+5mm each) on other than fair faces of brick work or concrete surfaces in cement mortar 1:4,mixed with integral water proofing compoundwith weight of cement in top layer as per manufacturers instructions and finished the surface even and fair without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item). 47 Supply only integral water proofing compound [ISI marked] of approved make. 48 M&L for10 mm thick rendering in CM 1:6 onfair face of brick workfinish the surface fair and even without using extra cement complete all as specified and directed by Engineer-in-Charge. 49 M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed. 50 M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4and finished the surfaces even and fair without using extra cement complete all as specified and directed. 51 S & F aluminium Anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and directed by the Engr-in-Charge. 52 M & L for 8 mm thick, Seamless calcium silicate ceiling made out of600 x 600 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face to centre, board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish including two coats of OBD over a coat of primer complete all as specified and directed. (Note : Frame work for ceiling shall be measured and paid separately) 53 Providing and fixing factory made uPVC white colour Sliding window Three track(Area not exc 2.0 Sqm each) made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) 54 S & F for Powder coated Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. 55 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full Body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm 2 , modules of elasticity 900 N/mm 2 and resistance to spread of flame of Class A category with water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 56 S&F wood plastic composite (WPC) factory made door shutter of 30 mm thickness made out of single pieces extruded wpc (wood plastic composite) profile with homogenous fine cellular structure made with plastic and wood powder having solid structure which is eco friedndly with density not less than 650 kg/Cum,and UV digitally printed to the desired design with UV lacquer coated to give surface added strength and protectionandhigh grade uv resistance and with heat, fire retardant will be hungand screws withdrawl strength 1800 n(face) & 900 n (edge), minium compressive strength of 50n/mm2 , E=900 n/mm2 and resistance to spread of flame of class a category with property of being teRmite / borer proof water/moisture proof and fire retardantand fixing with stainless stel butt hinges of required size with necessasry full body threaded star headed counter sunk s.s screw of size 10mm dia and 100 mm long , complete all as per direction of engg-in- charge. 57 S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and directed. 58 S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed. 59 S&F 125 mm long SS butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed. 60 S & F 150 mm long fancy type cromium plated brass handles, cast type, polished bright of sizecomplete all as specified and as directed. 61 S & F 150 mm size fancy type cromium plated brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts complete all as specified and as directed. 62 S & F for 300mm long fancy type cromium plated brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts complete all as specified and as directed. 63 S & F floor door stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed. 64 S&F aluminium (extruded section) door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed. 65 S & F 100mm long medium weight, cold rolled mild steel Butt hinges complete all as specified and as directed. 66 S&F 150mm long. extruded aluminium alloy handles, fabricated type, complete all as specified and as directed. 67 S&F150mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed. 68 S & F Aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clipes of sheet, cast or extruded sections and fixing bolts of extruded sectionsor cast aluminium alloy, length of bolt of 300 mm complete all as specified and directed. 69 Supply only 5.0 mm thick figured glass, pinhead type in squares n exc 0.5 sq. m each pane complete all as specified and as directed. 70 Supply only 5.5 mm thick sheet glass ordinary quality in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed. 71 Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. 72 S&F 4.0 mm thick figured glass, pinhead type in squares n exc 0.5 sq. m each pane complete all as specified and as directed. 73 S&F4.0 mm thick sheet glass ordinary quality in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed. 74 S&F decorative type stainless steel curtain rod of 25 mm dia and decorative type brass globe type brackets/end knobs of size suitable to 25mm dia curtain rod complete all as specified and as directed. 75 S & F polyester venetian blinds/curtains of approved pattern and design suitable for windows of size 5ft (W) x 5ft (H) including all necessary fittings complete all as specified and directed. 76 M&L for preparation of new platered surface of wall and applyingtwo coats of weather proof 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre, dart pick up resistant,silicon enhanced,UV resistant and PU enhanced propertyover a coat of alkali resistant primer including applying one or more coat of wall care putty to a smooth surface including making good any undulations on the surfacesincluding all necessary scaffolding,complete all as specified and directed.Note :-Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS 77 M & L for preparing newly plastered surfaces of wall and applyingtwo coats of oil bound washable distemper over a coat ofprimer including applying one or more coat of wall care putty to get a smooth surface including making good any undulations on the surfacescomplete all as specified and as directed.Note :- (i) Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS(ii) Sanding of surfaces shall be done by mechanical sander with 1500-2700 rpm with internal dust extraction system for clean environment certified by the Paint manufacturer) 78 All as per item no 76 here in before but on ceiling 79 M & L for preparing newly plastered surfaces of walls, etc and applying three coats of white wash complete all as specified and directed. 80 M & L for 25 mm average thick PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in as in Sub base for flooring/levelling course etc. finishing the top surface even and fair complete all as specified and directed. 81 M & L for double charged Vitrified, designed, light shade coloured (light shade), tiles, 7 to 8 mm thick, (square/rectangular) polished, area of each tiles not exc 0.36 sqm, in floors, etc including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed. 82 M & L for double charged Vitrified, designed, light shade coloured, tiles, 7 to 8 mm thick, (square/rectangular) polished, area of each tiles not exc 0.36 sqm as in vertical surfaces such as skirting,dado, etc including 10 mm thick bedding in cement mortar 1:4 and necessary cutting of tiles complete all as specified and directed. 83 M & L for non skid ceramic tiles, joint free, light shade coloured, premium quality of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 complete all as specified and as directed. 84 M & L for non skid ceramic tiles, joint free, light shade coloured, premium quality of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 to 8 mm thick [Square or Rectangular] as as in vertical surfaces such as Skirting/dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed. 85 M & L for non skid ceramic tiles, joint free,light shade coloured, premium quality of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 complete all as specified and as directed. 86 M & L for joint free glazed ceramic tiles, edge cut, coloured, premium quality, of size 300 mm X 450 mm, 7 to 8 mm thick as in vertical surfaces such as skirting, dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed. 87 M & L for granite stone slab (of any type) 18 to 20 mm thick (Table rubbed and polished to smooth mirror finish), machine cut, colour Mexican Red/Ruby Red/Z black/Paerl black etc design/pattern as directed including inlays, borders, margins in two or more colours/shades as in floors, trades of steps, cill cooking platform etc set and beddedover 15 mm thick screed bed in cement mortor 1:6and jointed with grey cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite slabs& cutting, polishing complete all as specified and directed.(Note: Single stone slab shall be used for entire length/height of steps, jambs, pillars, window cills, cooking platform etc and joints shall match with the flooring complete) 88 M & L for 18 to 20mm thick Granite (of any type) work (table rubbed and polished) in floors, steps, jambs, pillars, window-cills, cooking platforms and like bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15 mm thick screed bed in cement mortar 1:6 & cutting, polishing complete all as specified and directed. 89 M & L for vitrified designer outdoor tiles of size 400 x 400mm, 10 mm thick, as in deck flooring,floor/path, set, jointed and pointed in neat cement slurry with grey cement and pigments, laid over and including 15 mm thick screed bed in CM(1:4)allas specified.Make :- Johnson endura designer collection series or equivelant of make as per List of manufacturers mentioned in PS. 90 M & L for vitrified designer outdoor tiles of size 400 x 400mm,10 mm thick, as in skirting /dado/cladding, set, jointed and pointed in neat cement slurry with grey cement and pigments, laid over and including 10 mm thick rendering in CM(1:4) allas specified. Make :- Johnson endura designer collection series or equivelant of make as per List of manufacturers mentioned in PS. 91 Providing edge moulding to 18-20mm thick granite stone of countersvanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed 92 M & L for roughening of old concrete floor surfaces by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0 KG of cement per Sq.m area complete all as specified and directed 93 M & L for 10 mm thick, screed bed as in roof in cement mortar 1:3finishing the surfaces even and smooth without using extra cement mixed with water proofing compound as per manufacturers instructions complete all as specified and directed. (Note: WPC shall be measured and paid seperately) 94 Material and labour for preparation of horizontal or vertical surfaces for water proofing treatment on existing cleaned non accessible RCC roof with the following specification and manufacturings instruction complete all as specified and as directed:-(a) Preparing and cleaning of fully dry surfaces as per IS3067-1966(b) Applying bitumen primer(85/25 grade)conforming to IS:3384-1968 over the cleaned plaster surface @ 0.5 Ltr per sqm by the same membrane manufacturer of density at 25°C, 0.87 to 0.89 kg / Liter and viscosity 70-160 cps shall be applied on the prepared surface.(c) Applying a layer of APP based polymeric membrance 3.0mm thick (minimum) weight 3.6Kg per sqm (reinforced) with polyster Non woven fabric weighing not less than 160gms per sqm by torch application.The over laps shall be minimum 100mm on the transverse direction and 75 mm on longitudinal direction. 95 Supply and fixing Heat Resistant roof/Terrace Tiles ofsize 300 mm x 300 mm of thicness 10 mm minimum ,white coloured, with mineral composition, SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) mixed withwater proofing compound ,applying cement slurry and scratching the screed bed for proper fixing of tiles,laying the tiles with 3 mm spacers and grouting the joints with Masking tapebefore putting the Polymer Modified cementitious Grout , including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner complete all as specified and directed.Note : Waterproofing compound shall be measured and paid separately 96 S&F stainless steel (Grade 316) railing /ballster/handrail made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement ,SS tubes shall be welded at the turnings and junctions, welded portions shall be completely grinded and brought to bright and smooth finish including all bends, elbows, making holes in the floor / steps, grouting with epoxy to achieve full strength of railing complete all as specified and as directed. 97 S & F rolled mild steel in stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. conforming to Fe 410W Gde E-250, quality-A complete all as specified and directed. 98 S & F rolled mild plates (plain or chequered) channels, square cut or notched, forming holes with riveted, bolted or welded attachment conforming to Fe 410W Gr E-250, quality-A complete all as specified and directed. 99 S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut with diameter of neck 11 to 15 mm, but length of bolt exc 10 cm but n.exc 15 cm long all as specified and as directed. 100 M & L for preparation of newly steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete alll as specified and directed. 101 S & F for WPC decorative Grill jali 18mm thick of approved size and pattern andfixed with MS Holllow Square tube section 50mm x 50mm vertical at every 4 (MS Hollow square tube section 50mm x 25mm horizontal top and bottom of jali fixing the jali with MS Square tube with MS Plate/Clite and screw bolts complete. 102 S & F 1000 litres capacityrotational moulded polyethylene water storage tank, double layer construction, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long, 25 mm dia tank nipple ,hoisted and fixed in position complete all as specified and directed. 103 S & F 5000 litres capacityrotational moulded polyethylene water storage tank, double layer construction, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long, 25 mm dia tank nipple ,hoisted and fixed in position complete all as specified and directed. 104 S & F 25 mm bore,Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 455 gms) complete all as specified and directed. 105 S & F for CPVC ball valve 25 mm outer diameter & Plain CPVC SDR 11 fittings suitable for 25mm outer dia CPVC pipes complete all as specified and directed. 106 S & F 110mm bore PVC [SWR] pipes single socketed, in any length with solvent cement/ rubber ring joints, fixed to walls with necessary brackets, clamps complete all as specified and as directed. 107 S & F 75mm bore PVC [SWR] pipes single socketed, in any length with solvent cement/ rubber ring joints, fixed to walls with necessary brackets, clamps complete all as specified and as directed. 108 S & F 110mm bore PVC [SWR] pipes single socketed, in any length with solvent cement/ rubber ring joints, laid in trenches or in floors complete all as specified and as directed. 109 S & F 75mm bore PVC [SWR] pipes single socketed, in any length with solvent cement/ rubber ring joints, laid in trenches or in floors complete all as specified and as directed. 110 S & F 110 mm bore PVC [SWR] bends of any radius with access door including jointing with solvent cement complete all as specified and as directed. 111 S & F 110 mm bore PVC [SWR] bends of any radius including jointing with solvent cement complete all as specified and as directed. 112 S & F 75 mm bore PVC [SWR] Bends of any radius with access door including jointing with solvent cement complete all as specified and as directed. 113 S & F 75 mm bore PVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed. 114 S & F 110 mm borePVC (SWR) junction single, (Single T) equal or unequalincluding jointing with solvent cement complete all as specified and as directed. 115 S & F 110 mm borePVC (SWR) junction single, (Single T) equal or unequalincluding jointing with solvent cement complete all as specified and as directed. 116 S & F 110 mm borePVC (SWR) junction single, (Single T) equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. 117 S & F 110 mm borePVC (SWR) junction single, (Single T) equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. 118 S & F 110 mm borePVC (SWR) junction double, (Double T) equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. 119 S & F 75 mm borePVC (SWR) junction double, (Double T) equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. 120 S & F 110mm bore PVC (SWR) branch piece, single (single Y) equal orunequal with access door including jointing with solvent cement complete all as specified and as directed. 121 S & F 75mm bore PVC (SWR) branch piece, singlee (singlee Y) equal orunequal with access door including jointing with solvent cement complete all as specified and as directed. 122 S & F 110 mm bore PVC [SWR] vent cowl including jointing with solvent cement complete all as specified and as directed. 123 S & F100mm bore outlet PVC [SWR] Floor trap/ Nahani trap with SS grating including jointing with solvent cement complete all as specified and as directed. 124 S & F75mm bore outlet PVC [SWR] Floor trap/ Nahani trap with SS grating including jointing with solvent cement complete all as specified and as directed. 125 Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. 126 Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. 127 S & F20 mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing, complete all as specified and as directed. 128 S & F25 mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing,complete all as specified and as directed. 129 S & F32 mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing,complete all as specified and as directed. 130 S & F Vitreous China Rimless Single Piece WC with UF soft close slim seat cover, Hinges,fixing Accessories, dual flush fittings, Size: 360x655x765 mm, P Trap - 180 mm and all fittings and fixtures including connection to outgoing drain including making good damaged/disturbed surfaces complete all as specified and directed. Make: Jaquar Cat No. LYS-WHT-38851P180UFSMor equivelant model of make as per list of manufacturer mentioned in PS. 131 All as per item no 129 here-in-before but Supply and fixing in repair . Make: Jaquar Cat No. LYS-WHT-38851P180UFSMor equivelant model of make as per list of manufacturer mentioned in PS. 132 S & F 15 mm bore, Hand Shower (Health Faucet) with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hook with all accessories complete all as specified and directed. Make: Jaquar Cat No. ALD-573 or equivelant model of make as per list of manufacturer mentioned in PS. 133 All as per item no 131 here-in-before but Supply and fixing in repair . Make: Jaquar Cat No. ALD-573 or equivelant model of make as per list of manufacturer mentioned in PS. 134 S&F Toilet paper holder with with flap recessed type, chromium plated fixed to wall with brass screw complete all as specified and directed Make: Jaquar Cat No.ACN-1153S or equivelant of make as per List of manufacturers mentioned in PS. 135 All as per item no 133 here-in-before but Supply and fixing in repair .Make: Jaquar Cat No.ACN-1153S or equivelant of make as per List of manufacturers mentioned in PS. 136 S & F under counter sunk vitreous china rectangular wash hand basin of size 605x410x200mm with all necessary fixing accessories complete all as specified and directed . Make: Jaquar Cat No. FNS-WHT-40701or equivelant of make as per List of manufacturers mentioned in PS. 137 All as per item no 135 here-in-before but including taking down old one complete all as specified and directed . Make: Jaquar Cat No. FNS-WHT-40701or equivelant of make as per List of manufacturers mentioned in PS. 138 S&F in repairvitreous China wash basin, size 550 x 400mm, white, flat back, with 32 mm dia PVC waste pipe, CP waste coupling,& backets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and directed. 139 S & F 15 mm bore fancy type chromium plated pillar tap quarter turn for wash hand basin complete all as specified and directed .Make: Jaquar Cat No. FLP-5011PMor equivelant of make as per List of manufacturers mentioned in PS. 140 All as per item no 138 here-in-before but Supply and fixing in repair .Make: Jaquar Cat No. FLP-5011PMor equivelant of make as per List of manufacturers mentioned in PS. 141 S & F fancy type chromium plated towel ring square with round flange complete all as specified and directed . Make: Jaquar Cat No. ACN-1121N or equivelant of make as per List of manufacturers mentioned in PS. 142 S & F fancy type chromium plated soap dispenser with glass bottle complete all as specified and directed . Make: Jaquar Cat No.ACN-1135N or equivelant of make as per List of manufacturers mentioned in PS. 143 S & F 15 mm bore fancy type chromium plated bib cock with wall flange complete all as specified and directed . Make: Jaquar Cat No.KUP-35037PM or equivelant of make as per List of manufacturers mentioned in PS. 144 All as per item no 142 here-in-before but Supply and fixing in repairMake: Jaquar Cat No.KUP-35037PM or equivelant of make as per List of manufacturers mentioned in PS. 145 S & F 15 mm bore fancy type chromium plated two-way bib cock with wall flange complete all as specified and directed . Make: Jaquar Cat No. KUP-35041PM or equivelant of make as per List of manufacturers mentioned in PS. 146 All as per item no 144 here-in-before but Supply and fixing in repairMake: Jaquar Cat No. KUP-35041PM or equivelant of make as per List of manufacturers mentioned in PS. 147 S & F 15 mm bore fancy type chromium plated angular stop cock with wall flangecomplete all as specified and directed . Make: Jaquar Cat No. FLP-5053PM or equivelant of make as per List of manufacturers mentioned in PS. 148 All as per item no 146 here-in-before but Supply and fixing in repairMake: Jaquar Cat No. FLP-5053PM or equivelant of make as per List of manufacturers mentioned in PS. 149 S & F for fancy type chromium plated overhead shower 120mm round shape single flow (ABS body chrome plated with grey face plate) with rubit cleaning system including shower arm casted 190mm long flat shape for wallmounted showers with flange and all necessary accessories complete all as specified and directed . Make: Jaquar Cat No. OHS-1789 (Shower) and SHA-483 (Arm) or equivelant of make as per List of manufacturers mentioned in PS. 150 S & F 600mm x 900mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with 6 Nos of 10mm dia capastan head chromium plated brass screws and cup washers complete all ass pecified and directed. 151 All as per item no 149 here-in-before but Supply and fixing in repair . 152 S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.Make: Jaquar Cat No. CAN-1171N or equivelant of make as per List of manufacturers mentioned in PS. 153 All as per item no 151 here-in-before but Supply and fixing in repair .Make: Jaquar Cat No. CAN-1171N or equivelant of make as per List of manufacturers mentioned in PS. 154 S & F vitreous China urinal, with all fixing accessories set, of Size 355x 340x 535 mm, starwhite with grating,CP spreader and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete complete as specified and directed. Make: Jaquar Cat No. URS-WHT-13261H or equivelant of make as per list of manufacturers mentioned in PS. 155 All as per item no 153 here-in-before but Supply and fixing in repairMake: Jaquar Cat No. URS-WHT-13261H or equivelant of make as per list of manufacturers mentioned in PS. 156 S & F 32mm bore, chromium plated brass Bottle trap for wash hand basin with inlet and outlet, screwed for pipe or connections including necessary apcking union and cap fixed complete all as specified and directed. 157 S & F 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and directed. 158 S & F in repair, 32mm dia flexible PVC waste pipe, 900mm long for wash basin/sink/urinal etc complete all as specified and directed. 159 S&F in repair single towel rail 600mm long,stainless steel complete all as specified and directed.Make: Jaquar Cat No. ACN-1111SM or equivelant of make as per List of manufacturers 160 S & F in repairs Vitreous china premium/ 1st quality rimless wall hung WC with PP soft close slim seat cover, hinges, accessories Set,Size: 355 mm x 555 mm x 370 mm incl all necessary accessories like rag bolts/ gel gasket etc (excluding flushing cistern) complete in all respect all as specified.Make: Jaquar Cat No. FLS-WHT-5953PPSM or equivelant of make as per List of manufacturers 161 S & F in repairs, vitreous China squatting pan, Orissapattern, size 580 x 440 mm white with integral foot rest and P or S trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing specifications complete all as specified and directed. 162 S & F in repair 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white,with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and directed. 163 S & F in repair Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern fixed complete all as specified. 164 S & F in repair Plastic water closet seat cover, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device. 165 S & F in repair vitreous China Urinal partitions slabs terminating about 40cm above floor line complete all as specified and directed 166 Material and labour for prepration of old plastered or unplastered surfaces of walls and applying one coat of white wash complete all as specified and directed. 167 All as per serial item No 165 here -in - before but on ceiling. 168 M&L for applying one coat of oil bound washable distemper to old decorated plastered (distempered) surfaces of wall,cornices,pilasters including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) complete all as specified and directed by Engineer -in-Charge.Note :- Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS 169 M & L for preparation old decorated external surfaces of wall, chajja, facia, ceiling parapet etc including cornices, pilasters etc including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, effloresecnt salts, trading oil, greasy spots and applying one coat of weather proof 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre, having dart pick up resistant, silicon enhanced, UV resistant and PU enhanced property including all necessary scaffolding complete all as specified and as directed.Note :- Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS 170 S & F 12mm thick ordinary Glass door with double shutterincluding long type 450 mmSS handles, floor springs and locking arrangement and all necessary fittings complete all as specified and directed. 171 M & L for hardcore of gauge n.exc 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed. 172 M & L for 150mm thick PCC 1:2:4 type B- 2, using 40mm graded aggregate as in sub-base, floors and pavings etc with machine trowel finish, vaccum dewatering flooring complete all as specified and directed. 173 M & L for 75 mm thick,plain cement concrete1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed. 174 M & L for 100mm thick plain cement concrete 1:4:8 type D- 2 using 40mm graded aggregate as in sub-base, floors and pavings etc complete all as specified and directed. 175 M & L for sand filling under floors or in foundations incl watering and consolidation complete all as specified and directed. 176 M & L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey cement and pigment complete all as specified and directed. 177 M & L forproviding, cement concrete 1:2:4 type B-1 using 20 mm graded aggregate as in roof kerbs or mud stops, rounded or chamfered on edges and coping including nescssary formwork complete all as specified and directed 178 M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished the surfaces even and smooth without using extra cement complete all as specified and directed. 179 M & L for precast reinforced cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab (For manhole etc), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain facesand set in cement mortar 1:4 including necessary form, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measuredand paid separately) 180 S&L reinforced concrete pipes, class NP2, 150 mm bore, laid and jointed with collars complete all as specified and as directed. 181 Supply, laying, connection and testing, 50mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, etc complete all as specified and directed. 182 Supply, laying, connection and testing, 25 mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, etc complete all as specified and directed. 183 S & F 50 mm bore, gun metal, globe or Gate valves with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed. 184 S & F 25 mm bore, gun metal, globe or Gate valves with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed. 185 Cutting existing CI/DI water mains of dia 200 mm and making branch connection by inserting tee/elbow/reducer etcall as specified and directed by Engr-in-Charge. 186 M & L for conceledPoint wiring with two runs of single core 1.5 Sq.mm. (Nominal area) PVC insulated unsheathed multistranded copper conductor cable FRLSH (ISI marked) drawn through and including non metallic PVC conduit 20 mm bore (Minimum) medium grade (ISI marked) concealed type includingmetal GI boxes of suitable module including modular white cover plate of suitable module for fixing modular type switches, sockets, regulators etc. including provision of multistranded 1.5 Sq.mm copper conductorcable FRLSH [ISI marked] as earth wire connected to common earth dolly and earth in distribution board complete all as specified and as directed,for one light/exhaust fan/fan point/call bellcontrolled by one way switch.(Note.: (i) The rate quoted is deemed to include making good the disturbed sufaces and to match the adjoining surface. (ii) The quoted rate is deemed to include cutting chases for concealed wiring including making good the same as per the existing one) 187 All as per item No. 185 above but for One 3/5 pin socket outlet 6 amps on independent board complete ditto 188 All as per item No. 185 above but for One 3/5 pin socket outlet 6 amps pointon same boardcomplete ditto 189 All as per item No. 185 above but for One light point controlled by two way switch complete ditto 190 All as per item No. 185 here in before but for one 15 Amps power point on the independent board with two runs of PVC insulated and unsheathed copper conductor cable of size 2.5 Sqmm multistrandedFRLSH (ISI marked) and 2.5 Sqmm PVC insulated unsheathed solid copper conductor cableFRLSH (ISI marked) as earth lead complete ditto 191 All as per item No.185 here in before but for one 15 Amps power point on the independent board with two runs of PVC insulated and unsheathed copper conductor cable of size 4.00 Sqmm multistrandedFRLSH (ISI marked) and4.00 Sqmm PVC insulated unsheathed solid copper conductor cableFRLSH (ISI marked) as earth lead complete ditto 192 S & F switch modular single pole one way 6 amp 240 volts,1 Module complete all as specified and as directed. 193 S & Fmodular bell push single pole one way 6 amp 240 volts,2 Module with indicator complete all as specified and as directed. 194 S & F Modular socket outlet6A, 2/3 pin combined, 2 module, AC 230V, 50HZ complete all as specified and as directed. 195 S & F switch modular single pole one way 16 amp 240 volts,1 Module complete all as specified and as directed. 196 S & F Modular socket outlet6A/16A, 2/3 pin combined, 2 module, AC 230V, 50HZ complete all as specified and as directed. 197 S&F ceiling rose, 65 X 50mm two to three teRminals, PVC/polycarbonate, insolated body complete all as specified and directed. 198 S & F switch modular single pole two way 6 amp 240 volts,1 Module complete all as specified and as directed. 199 S & F steped type modular fan regulator ,100/120 W 2 module complete all as specified and as directed. 200 S&FBell Ding Dong AC 230 Volts,50 Hz single pole complete all as specified and as directed. 201 S & F Telephonic jack deluxe with shutter single line with metal box complete all as specified and as directed. 202 S&F Socket Residual Current Device (SRCD) With Steel Enclosure two pin and earth plug including 20 Amps MCB SP complete all as specified and as directed 203 Supply and fixingLED Ceiling light fitting 35/36 watt recess type flat panel 600x600 mm fabricated CRCA sheet housing duly powder coated with high efficient LED`s & glare free high efficiancy PMMA diffuser complete with driver, holders & LED lamp and all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable complete all as specifide and directed. 204 S&F in repair LED lights fitting 1x 20W, 220V, including lamp AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 205 S&F in repair LEDlight fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 206 S&F LED building security light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including theRmal management in triple optics complete with IP 66 protection with and including 1.5 Sqmm weather proof 3 core FRLH grade copper conductor and 32 mm dia( or higher size as per manufacturers recommendation)light grade GI pipe (bend to shape or as per manufacturers recommendation ) bracket 1.5 mtr longcomplete with MS flat iron clamp (clamps shall be 40 x 5 mm MS flat) nuts, bolts & washers including painting the clamps with two coat of aluminium paint over a coat of red oxide primercomplete all as specified and as directedcomplete all as specified and directed 207 S & F powder coated sheet steel Distribution Board, TPN 4 Way, vertical , 415V, Double door with IP 43protection, IK 09 complete all as specified and as directed. 208 S & F powder coated sheet steel Distribution Board, TPN 6 Way, vertical , 415V, Double door with IP 43protection, IK 09 complete all as specified and as directed. 209 S & F powder coated sheet steel Distribution Board, SPN 8 Way, vertical , 240V, Double door with IP 43protection, IK 09 complete all as specified and as directed. 210 Supply, fixing, commissioning and testing MCB SPN 40 Amps, 240 Volts, 10KA, C curve complete all as specified and as directed 211 Supply, fixing, commissioning and testingMCB SP 6-32A Amps, 240 Volts,10KA, C Curve complete all as specified and as directed 212 Supply, fixing, commissioning and testingMCB TPN63Amps, 240 Volts,10KA, C Curve complete all as specified and as directed 213 M & L for Sub main wiring with 2 runs of Single core 2.5 Sqmm [ for Phase & Neutral ]PVC insulated multi stranded FRLSH (ISI marked) copper cable drawn through and including surface PVC conduit of suitable size with all conduit accesories and fittings along with 1 run of single core 2.5 Sqmm PVC insulated multi stranded FRLSH (ISI marked) copper cableas earth continuity conductorcomplete all as specified and as directed.(Note :- Two runs of 2.5 Sqmm and one runs of 2.5 Sqmm cable as earth wire and one run of conduitshall be measured as one length) 214 M & L for Sub main wiring with 2 runs of Single core 6 Sqmm [ for Phase & Neutral ]PVC insulated multi stranded FRLSH (ISI marked) copper cable drawn through and including surface PVC conduit of suitable size with all conduit accesories and fittings along with 1 run of single core 6 Sqmm PVC insulated multi stranded FRLSH (ISI marked) copper cableas earth continuity conductorcomplete all as specified and as directed.(Note :- Two runs of 6 Sqmm and one runs of 6 Sqmm cable as earth wire and one run of conduitshall be measured as one length) 215 M & L for Sub main wiring with 4 runs of Single core 10 Sqmm [ for Phase & Neutral ]PVC insulated multi stranded FRLSH (ISI marked) copper cable drawn through and including surface PVC conduit of suitable size with all conduit accesories and fittings along with one run of single core 10 Sqmm PVC insulated multi stranded FRLSH (ISI marked) copper cableas earth continuity conductorcomplete all as specified and as directed.(Note :- Four runs of 10 Sqmm and one runs of 10 Sqmm cable as earth wire and one run of conduitshall be measured as one length) 216 S & F Vertical TPN DB double door for provision for four pole MCCB upto 125Aincommer 8 way 24 outgoing with IP 43 protectioncomplete all as specified and as directed. 217 S & FMCCB 415 Volt, 25 KA, 4 Pole, 100 Amps Capacity with fixed thermal magnetic protection unit complete all as specified and as directed. 218 Supply, fix, installation and commissioning BLDC ceiling fan of less noise, silent operation, speed controlable by regulator, light colour, conforming to IS-374-2019, 1200 mm sweep, 230 Volts, BEE 5 Star rating, any Govt recognised Lab tested, power factor >0.94 Wattage and not more than 35 Watt, air delivery not less than 215cmm and all accessories such as down rod etc and connecting up with 1.5 Sqmm, PVC insulated, multistranded copper conductor cables from ceiling rose to fan complete all as specified and directed. (Note: Ceiling fan should have minimum 2 years manufacturers warranty) 219 Supply and fixing exhaust fan 300 mm size,metal body ,blade,louvers suitable for operation on single phase 240 V AC, 50 Hz and including connecting up withtwin core PVC insulated , sheathed flexible copper conductor cable of size 1.50 sqmm including making good disturbed surfaces to match with surronding complete all as specified and directed. 220 M & L fabrication, installation, commissioning and testing of 415 Volt, 3 phase, 4 wire system LT feeder pillar boxCPRI approved , Dust and vermin proof powder coated ,size cubical, kiosk and outdoor type having double door with front and back openable made of 3.15 mm thick CRCA sheet and shall be folded and braced as necessary to provide a rigid support for all components and 2.0 mm thick CRCA sheet for inner sheet, provided with handle locking arrangement 2 keys based on suitable size of MS angle 50 x 50 x 6 mm angle iron channel complete to accommodate moulded case circuit breakers meters including indicating lamps, current transformer, selector switch, 400 Amp single insulated bus bar for R-Y-B-N with heat shrinkagePVC sleeve in suitable bus chambers, interconnection required lugs of suitable size, copper cable for wiring, name plate, danger plate with independent compartment for busbars with hinged doors for each outgoing/incoming feeders & its accessories, cable alley with hinged doors, bus chambers with bolted doors, dust & vermin proof construction with rubber gasket, powder coating including numbering and lettering mounted on U channel of suitable size over PCC platform must be 0.5 mtrs above GL of appropriate size comprising compartment with necessary arrangements for following items:INCOMING:a) MCCB 4 Pole (Ics= 100% Icu) with fixed thermal magnetic protection unit 250Amp rotary type , 50 Hz, 415 V with rupturing capacity 25 KA - 01 no.OUTGOING:a) MCCB 4 pole with fixed thermal magnetic protection unit ,125A, 50 Hz, 415 V with rupturing capacity 16 KA-1 Nosb) MCCB 4 pole with fixed thermal magnetic protection unit, 100A, 50 Hz, 415 V with rupturing capacity 16 KA-3 Nosc) Intelligent Panel meter to measure voltage, current, frequency, power factor, etc with all connected CTs -01 nod) LED Indicating Lamps for each phase with colour coed Red Yellow Blue for R, Y and B Phases -01 no 221 S&F addressable type Fire alarm control panel alongwith network card and sensor status indicatorcomplying with BSEN 54 single loop panel of capacity from 99 detectors & 99 modules upto 200 detector and modules complete all as specified and directed. Make: Honeywell / Appollo / Siemens / Alert / Cosmos / Tata 222 S&F detectors complying with and type certified to EN - 45 addressable type multisensor detector with heat and smoke combination as per IS: 11360 complete all as specified and directed.Make: Honeywell / Appollo / Siemens / Alert / Cosmos / Tata 223 S&F addressable type explosive proof manual call point resettable type complete all as specified and directed. Make: Honeywell / Appollo / Siemens / Alert / Cosmos / Tata 224 S&F addressable type loop sounders along with inbuilt isolators complete all as directedMake: Honeywell / Appollo / Siemens / Alert / Cosmos / Tata 225 S&F PVC insulated & screened, both inner and outer PVC sheathed ,FRLS armoured high conductivity annealed bare electrolytic copper conductor of size 1.5 Sqmm 2Core,650/1100 V grade,with proper pair identification,1.2 Standard as per IS 1554, part -1 & IS 5831 latest and any other relevant standard completeall as directed. Make: Polycab/KEI/Havells 226 S&F Rigid non-metalic PVC conduit (20mmdia) exclusive of boxes (junction/ treminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hook etc. complete all as specified and directed. 227 S&F short circuit isolator complete all as specified and as directed 228 Supply, installation & testing, Booster pumpconfirming to IS- 12469 :1988 with CI casing bronze impeller and stainless steel shaft mounted on heavy duty bearings suitable for 440 volts, 3 phase, 50 Hz,30m head, 450 LPM discharge complete all as specified and directed. 229 S&F MS flanged pipe(For riser) 100mm bore, heavy duty for (G+2)building duly painted with 2 coats of synthetic enamel paint over coat of zinc chromate primer complete all as specified and directed. (For riser) 230 S&F cast iron sluice valve (heavy duty) hand wheel operated ,non raising SS spindle with gun metal parts, confirming to IS 14846, both end flanged class PN 1.6 of100 mm bore incl necessary nuts, bolts washers and gasketcomplete all as specified and directed. 231 S&F cast iron non return valve (heavy duty) with hand wheel operated , SS spindle, confirming to IS 1538, both end flanged class PN 1.6 of100 mm bore incl necessary nuts, bolts washers and gasketcomplete all as specified and directed.(for jockey pump) 232 S&F hose reel drum of 20 mm size of 30 meter length complete with coupling branch pipe and nozzle complete all as specified and directed. 233 S&F automatic gun metal air release valve 50 mm dia suitable for domestic water supply complete all as specified and directed 234 S&F water pressure gauges of 0-25 kgs standard dia at delivery side of pump sets complete with connecting tubing, fitted with stop cocks etc all as per standard practice and as directed. 235 S&F 6kgABC type dry chemical powder fire extinguisher complete all as specified and directed 236 S&F 4.5kg Co2 type fire extinguisher complete all as specified and directed 237 S&F 9 litre fire extinguisher water stored pressure type complete all as specified and directed 238 S&F mild steel fire buckets metal thickness 18 - 20 SWG, 9 lit capacity each,, 3 Nos with stand complete all as specified and directed. 239 S&F MS Framed brackets of angles or tees with web and flanges for Pipe support for all types of pipes from wall /roof floor etc including hangars / fastners / elbows/supports / tees etc complete all as specified and directed. 240 Material and labour for construction of brick masonry valve pit of size 90 cm x 90 cm x 90 cm (internal dimension) with burnt brick (sub class B) in cement mortar (1:6) on 75 mm thick PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in foundation, 15mm thick rendering in cement mortar (1:4) internally, externally up to 15cm below GL, providing valve pit cover made out of 3mm thick MS sheet duly welded with provision of hinges, handle and locking arrangement including 40 x 40 x 5mm angle iron frame fixed on top of valve pit by means of hold fast 150mm long, embedded in PCC block 1:2:4 type B-1 (20mm graded aggregate) of size 230 X 200 X 100mm, applying two coats of anti-corrosive paint over a coat of red oxide, zinc chrome primer after preparation of steel & iron surfaces including necessary excavation &earth work in soft/loose soil and demolition of existing one complete as specified and directed all as per relevant TD drawing. (Note : Drawing not attached with the tender document.However, the same can be seen in AGE E/M office during working hours) 241 S&F DOL starter suitable for 7.5 HP motor, 5.5 kw,415 volt, 3 phase , relay range 9 to 15 Amps in sheet metel enclouser complete all as specified and directed.Make :- L&T cat no SS97210 or equivalent model of make Havells,Schnider 242 Supply, installation and testing inverter split AC units indoor /outdoor complete with cordless remote control with inbuilt air ioniser and plasma filter for better indoor air quality, minimum 5 starrating,copper condenser,copper cooling coil and EER 3.2 of capacity 1.0 TR including making holes of required diaonwalls and necessary masonry work for making gooddistrubuted surface and match with the existing colour,PVC drain pipe of required length complete all as specified. 243 Supply, installation and testing inverter split AC units indoor /outdoor complete with cordless remote control with inbuilt air ioniser and plasma filter for better indoor air quality, minimum 5 starrating,copper condenser,copper cooling coil and EER 3.2 of capacity 1.5 TR including making holes of required diaonwalls and necessary masonry work for making gooddistrubuted surface and match with the existing colour,PVC drain pipe of required length complete all as specified. 244 Supply, installation and testing inverter split AC units indoor /outdoor complete with cordless remote control with inbuilt air ioniser and plasma filter for better indoor air quality, minimum 5 starrating,copper condenser,copper cooling coil and EER 3.2 of capacity 2.0 TR including making holes of required diaonwalls and necessary masonry work for making gooddistrubuted surface and match with the existing colour,PVC drain pipe of required length complete all as specified. 245 S & F voltage stabilizer of capacity 3 KVA, single phase, input working voltage 170-250 Volts, metal body with time delay system, wall mountable, built in thermal overload protection, low & high voltage cut-off protection, micro controller based design complete all as specified and directed.Make: V-Gaurd model no VG-300 or equivalent model of make mentioned in PS 246 S & F voltage stabilizer of capacity 4 KVA, single phase, input working voltage 170-250 Volts, metal body with time delay system, wall mountable, built in thermal overload protection, low & high voltage cut-off protection, micro controller based design complete all as specified and directed.Make: V-Gaurd model no VG-400 or equivalent model of make mentioned in PS 247 S & F voltage stabilizer of capacity 5 KVA, single phase, input working voltage 170-250 Volts, metal body with time delay system, wall mountable, built in thermal overload protection, low & high voltage cut-off protection, micro controller based design complete all as specified and directed.Make: V-Gaurd model no VG-500 or equivalent model of make mentioned in PS 248 S&F Socket Residual Current Device (SRCD) With Steel Enclosure two pin and earth plug including 25 Amps MCB SP complete all as specified and as directed(Make : Havells Cat Part No. DHDDCDP025202503 or equivelant model of make mention in PS) 249 S&F copper pipe line heavy duty 1/4 diawith flair nuts and insulation as sunction/ discharge pipe of split AC complete all as specified and directed. 250 All as per item no 248 but 1/2 dia copper pipe for discharge line complete all as specified and directed. 251 S & F MS stand for mounting outdoor unit of Acscomplete all as specified and as directed. 252 M & L Earthing complete with GI earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected with galvanised earth strip of size 32x6 mm by means of bolts, nuts,check nuts and washers protected by 15mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, with 40 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia defoRmed bar @ 10 cm C/C both ways and suitable handle of 12 mm dia round bar),including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel, wire mesh, aluminium lugs, complete in all respect all as shown in electrical plate No. 3 and other end connected with main switch board or Earthing test point as directed,including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessarytesting on completion complete all as specified and as directed by the Engineer-in-Charge.Note: On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost 253 S&F earth continuity conductor or main earthing lead with 32 x 6 mm GI Strip fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc as requiredcomplete all as specified and directed. 254 Supply and laying cable XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 185 Sqmm 3.5 core, fixing along the poles or passing through pipes or laid under floor of through walls etc jointing and testing complete all as specified and directed. 255 Supply and laying cable XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 Sqmm 3.5 core, fixing along the poles or passing through pipes or laid under floor of through walls etc jointing and testing complete all as specified and directed. 256 M & L for Sand cushioning with clean dry sand in trenches for protection of under ground cables (below, above and around the cable laid in trenches) complete all as specified and directed.(Note: Thickness after punning down shall be measured for payment) 257 Supply and laying well burnt bricks, fly ash bricks laid breath wise across the length of cable in trenches for protection of UG cables complete all as specified and directed. 258 M&L for preparing the soil base for planting grass by levelling the base to required slopes and levels, supplying and spreading 02 parts of sand, 01 Part of bio fertiliser and one part of red loamy virgin soil for growth of grass to an average thickness of 200mm including mixing vermin compost etc., to improve the fertility of the soil in the required proportion and finally preparing the soil base suitable for planting carpet grass etc. including remoal surplus debris outside MoD land, complete all as specified and as directed. 259 M & L for planting ever green grass of natural Korean/mexican feather carpet grass of approved pattern over the prepared base lawn/carpet area with good earth including watering, removing the weeds or any other vegetation, mixing the manure from time to time and pesticides as required for healthy growth as per standard gardening practice complete all as specified and directed.(NOTE:- Grass shall be maintained by watering, taking out weeds, manuring the organic manure at regular intervals, using chemical fertilizers, spraying pesticides etc. required healty growth, trimming branches/grass to maintain proper shape etc. all as per standard gardening practice for a period of two year from the certified date of completion of entire work) 260 M & L for plantingapproved species of crotons, hedge plants/sapling Acalypha variegated /duranto(height of plant not less than 75 cm above ground level) of approved spacies at a spacing not exceeding 200cm C/C including excavation of pit of min dimension 50cmx50cm50cm and removal of excavated earth to outside the MD land, preparation of ground upto 30cm deep and filling with good earth, cow dung, vermi composit and watering etc complete all as specified and directed.(NOTE:- Plants shall be maintained by watering, taking out weeds, manuring the organic manure at regular intervals, using chemical fertilizers, spraying pesticides etc. required healty growth, trimming branches/grass to maintain proper shape etc. all as per standard gardening practice for a period of two year from the certified date of completion of entire work) 261 Supply and planting approved species of Flower plant (Plant height 2-3 ft) with pots of approved species viz Lantama varities/ Plumeria Pudica/ Alamanda mini/ Ixoras/ button rose including necessary earth work and providing cow dung manure etc obtained from nurseries complete all as specified and directed.(NOTE:- Plants shall be maintained by watering, taking out weeds, manuring the organic manure at regular intervals, using chemical fertilizers, spraying pesticides etc. required healty growth, trimming branches/grass to maintain proper shape etc. all as per standard gardening practice for a period of two year from the certified date of completion of entire work) 262 All as per item no 260 but approved species of Ornamental Shrubs like baby crotons/erranthemum vatiedieds/ Thujas/ Furcuria(Plant height 1.00-1.5 ft) 263 All as per item no 260 but approved species of Pendanus/ Blueemarald / Latina Varities (Plant height 2-3 ft) 264 All as per item no 260 but approved species of Royal Palm/Fishtail Palms/Foxtail Palm/Viechiemowcry/ Green (Plant height 2-3 ft) 265 Supply , laying and testing 15 mm bore High density poly ethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete towalls, ceilings or in floors etc complete all as specified and directed 266 All as per item no 264 here-in-before but 20 mm bore 267 All as per item no 264 here-in-before but 50 mm bore 268 S & F 15 mm bore, water sprinkler suitable for Arboriculture works with rotaryspray heads/nozzles 180 degree made out of gum metal including necessary connection complete all as specified and directed. 269 PART-II ( Phase-II :- Maintenance of Arboriculture works during Defect Liability Period of works ) 270 Outsourcing services for day to day maintenance of all plants,Hedge, Grass provided under Sch A Part-Iby watering, taking out weeds, manuring the organic manure at regular intervals, using chemical fertilizers, spraying pesticides etc. for healty growth including trimming branches/grass to maintain proper shape etc. all as per standard gardening practice for a period of two year from the certified date of completion of entire workby employing 01 No Mali (unskilled) per day of 08 hrs duration except on Sundays and holidays complete as specified and directed. Note :Water shall be supplied by MES free of cost for maintaining the grass and plants. Contractor shall be responsible for all necessary arrangements for collection and conveyance of water from MES water supply points/ source up to 5 km from the site. Necessary water tanker with tractor,water browser ,PVC pipe,sprinkler etc required for watering purpose is the responsibility of the contractor.Manure and pesticide required for maintenance of the plantfor two years shall be the resposibility of the contractor. Quoted Rates shall deemed to include for all these aspect.
