Tender For Rewiring Of Internal Electrification Including Allied Works In Otm Accn And Other Area I Of Sector A Age E/M (N) Under Ge (N) Ambala.; 1 Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, socket outlet, etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etccomplete all as specified and as directed by the Engineer-in-Charge. 2 Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked with multi stranded copper conductorgreen colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly(boxesshall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer bothinternally and externally) including provision of new covered plate over sunken box for housing themodular switches , modular socket outlets,modularfan regulators etc.for one light/fan/exhaust fan/bell point controlledby one way switch,complete all as specified and as directedby Engineer-in-Charge. Note :-a) All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid forseparately . 3 Description all as per serial item No.02 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on independent board, complete all as specified and as directedby Engineer-in-Charge. 4 Description all as per serial item No.02 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on same board,complete all as specified and as directedby Engineer-in-Charge. 5 Description all as per serial item No.02 here-in-before but for one socket outlet 16 Amp with 2.50 sq mm PVC insulated, unsheathedcable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade, ISI marked with multi stranded copperwire as earth continuity conductor connected to common earth dolly, complete all as specified and as directed by the Engineer-in-Charge.Note : (i) Point wiring shall be done in a manner that not more than 02 socket point executed in one circuit.(ii) Each socket point will be measured and paid as per point. 6 Description all as per srl item No 02 here-in-before but for one socket outlet 16 Amp with 4.00 sq mm PVC insulated, unsheathedcable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 4.00 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copperwire as earth continuity conductor connected to common earth dolly, complete all as specified and as directed by the Engineer-in-Charge.Note : (i) Point wiring shall be done in a manner that not more than 01 socket point executed in one circuit.(ii) Each socket point will be measured and paid as per point. 7 Supply and fixing of modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts, complete all as specified and as directedby Engineer-in-Charge. 8 Supply and fixing of modular switch 1 module, single pole, one way 16 Amps flush type, 230 volts, complete all as specified and as directedby Engineer-in-Charge. 9 Supplyand fixing of modular bell push 6 Amp, 1 way, 1 module, 230 volts, complete all as specified and as directed by the Engineer-in-Charge. 10 Supply and fixing of modular socket outletmultipin combined,6 Amp, one way, two module, 230 volts, complete all as specified and as directedby Engineer-in-Charge. 11 Supply and fixing ofmodular socket outletmultipin combined, (6pin), 6/16 Amp, one way, two module, 230 volts, complete all as specified and as directedby Engineer-in-Charge. 12 Supplyand fixingas in repairelectronic Fan regulator, modular 100 watts, 1 module, 230 volts, 50 Hz, AC supply suitable for ceiling fan any type/make/sweep, complete, all as specified and as directed by the Engineer-in-Charge. 13 Supply and fixing in repair calling bell, ding dong, 230 volt, complete all as specified and as directed by the Engineer-in-Charge. 14 Supply and fixing ceiling rose surface type 2/3 terminalpolycarbonate, isolated body, complete all as specified and as directed by the Engineer-in-Charge. 15 Supply and fixing lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and as directedby Engineer-in-Charge. 16 Supplyand fixingin replacement LED lamp 9 wattthreaded/pin end, warm/cool lamp type as per site requirement suitable for fixing on existing batten/angular holders, completeall as specified and as directed by the Engineer-in-Charge. Cat part No. BL029WB22 of Make Benlo or equivalent make given in Appx B. 17 Supply and fixing in replacement LED lamp 12 wattthreaded/pin end, warm/cool lamp type as per site requirement suitable for fixing on existing batten/angular holders, completeall as specified and as directed by the Engineer-in-Charge.Cat part No. BL0212WB22 of Make Benlo or equivalent make given in Appx B. 18 Supply and fixing in repairLED batten fitting 10 watt, 2 feet, polycarbonate housing with electronic drivercool/warm type, connecting with copper conductor flexible cablefrom ceiling rose to connector of the light, complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LBLN-10-C-SQ of make Orient or equivalent make given in Appx B. 19 Supply and fixing in repairLED batten fitting 20 watt, 4 feet, polycarbonate housing with electronic drivercool/warm type, connecting with copper conductor flexible cablefrom ceiling rose to connector of the light, complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LBLN-20-C-SQ of make Orient or equivalent make given in Appx B. 20 Supply and fixing in repair, LED surface mounted bulk head luminaries 8-10 watt with min 800 lumen, IP 65, aluminium housing, surge protection including driver and LED lamp, etc. complete with all accessories, connecting with copper conductor flexible cable from ceiling rose to connector of the light, complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LIBH-10-C-P of make Orient or equivalent make given in Appx B. 21 Supply and fixing in repair,9/12 watt thermoplastic wall mountingfixture (sketch type) with B-22 LED lamp and includingconnecting with copper conductor flexible cablefrom ceiling rose to connector of the light complete and removing unserviceable light fittings, complete all as specified and as directed by the Engineer-in-Charge. Cat part No.DECO WALL LIGHT FROSTED of make Orient or LHFOGBE1TZ1W035of make Havells or equivalent make given in Appx B. 22 Supply and fixingSurface/Recess mounting LED 15/18 watt cool/warm type circular down lighter/ COB panelwith PVC housing, 240 volt, 50HZ, AC supplycompletewithall accessories internally pre wiredincluding connecting with 3 coreflexible copper conductor from ceiling rose to connector of the light, including disconnecting and taking down existing old unserviceable fitting, complete all as specified and as directed by the Engineer-in-Charge. Cat part No.LDRDZ-15-C of make Orient or equivalent make given in Appx B. 23 Supply and fixingSurface/Recess mounting LED 5/8 watt cool/warm typecircular down lighter/ COB panelwith PVC housing, 240 volt, 50HZ, AC supplycompletewithall accessories internally pre wiredincluding connecting with 3 coreflexible copper conductor from ceiling rose to connector of the light, including disconnecting and taking down existing old unserviceable fitting, complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LDRDZ-05-C of make Orient or equivalent make given in Appx B. 24 Supply and fixing in repair,LED Bldg Security Light Fittings of capacity 40-45 watt made up of die castaluminiumhousing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver and making electrical connection, complete all as specified and as directed by the Engineer-in-Charge.Cat part No.LSFS-45-CF-PC of make Orient orHLSLD-14-40-CWDL-R01 of make Halonix or equivalent make given in Appx B. 25 Supply and fixinginverter LED security light luminaire 30 watt , pressure die cast aluminum housing, toughened heat resistant glass, IP66 protection, better optics for uniform distribution with multiplte LEDshaving optical grade polycarbonate lens with 3 to 4 hours battery back up, auto on offall accessories internally pre wired and including connecting up with Two core 1.5 sq mmcopper conductor cable from connector to ceiling rose to connection of light including disconnecting and taking down oldunserviceable security light fitting of any description and in any position, complete all as specified and directed. Cat part NoLED SL 30W HLSLD-ML04-30-CWL-INV-RTC-R of make Halonix or equivalentin make given in Appx B. 26 Supply and fixing in repair, service bracket of mild steel pipe 25 mm bore medium grade of length 0.70 mtr fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts and washer and suitable reducer for connecting fitting to GI pipe as required at site includingtwo coats ofsynthetic enamel paintoverone coat of red oxide primer on mild steel work, complete all as specified and as directed by the Engineer-in-Charge. 27 Supply and fixingLED flat panel 2 x 2 size fully difused surface/ recess mounted fitting (grid/ gypsum type)36-40 watt , 5700K,warm/cool whitewith powder coating and CRCA front cover including framewith provision ofPVC flexible copper conductor cable from ceiling rose to light fitting as in repair, complete all as specified and as directed by the Engineer-in-Charge.Cat part No.LTRAQ-36-C-FC of make Orient or equivalentin make given in Appx B. 28 Supply and fixing recess mounted direct-indirect circular LED luminaire 2X2, 34 watt (26+8 watt) warm /cool day light with uniform light distribution, white colour powder coated deep drawn housing unique floating spherical high effeciency translucent PMMA diffuser for direct lighting with high effeciency LEDs, constant current, costant voltage driver with effeciency of min 85% suitable for grid / POP ceiling, complete all as specified and as directed by Engineer-in-Charge. Make : Wipro cat part No : LM38-461-XXX-57-XX or equivalentin make given in Appx B. 29 Supply & fixingLED Flood lights, 50 watt, IP-66, aluminum die cast housing with unique lens system and toughened glasswith gasket240 volt, 50Hz, AC supplycompletewithall accessories internally pre wiredincluding connecting with flexible copper conductorto connector of the light with necessary fixing arrangements, including disconnecting and taking down existing old unserviceable fitting, complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LFSM-050-C-V3 of make Orient or equivalentin make given in Appx B. 30 Supply & fixingLED Flood lights, 100 watt, IP-66, aluminum die cast housing with unique lens system and toughened glasswith gasket240 volt, 50Hz, AC supplycompletewithall accessories internally pre wiredincluding connecting with flexible copper conductorto connector of the light with necessary fixing arrangements, including disconnecting and taking down existing old unserviceable fitting, complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LFSM-100-C-V3 of make Orient or equivalentin make given in Appx B. 31 Supply and fixingLED Bollard 8-10 watt, IP-65 , 6500 K luminaire made ofpressure die castaluminium housing and clear glass , 240 volt, 50HZ, AC supply , completewithall accessories including electronic driver,internally pre wiredincluding connecting withthree core flexible copper conductor cable from Electric Supply Source to connector of the light as in repair, complete all as specified and as directed by the Engineer-in-ChargeCat No. HLOB-02-10-CW of make .Halonix or equivalentin make given in Appx B. 32 Material and labour for taking down existing light fitting of any type alongwith GI pipe/ pole of any dia / any size and supply and fixing of MS pipe (Hot dipped Galvanized) decorative pole in two sections i.e Top pipe not less than 70 mm outside dia x 1500 mm long and Bottom pipe not less than 110mm outside dia x 500 mm long, thickness of pipe not less than 3 mm with base plate 250 x 250 x 12mm thick having 14mm dia hole for fixing of foundation J bolts of size 12mm dia x 450 mm J including 115 x 200 mm long utility window in pole, including material & labour for fixing of suitable size nuts/bolts and washers including Tripple layer metallic PU paint (Etching, Epoxy & PU) having Embalishment aluminium castiing suitable for and alongwith 30/35 Watt Warm white LED post top lantern IP 65 environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs clear cover offers bright illumination including all fixing accessoreis including necessary excavation, removal and PCC 1:3:6 work as directed etc, complete all as specified and directed by Engineer-in-Charge. Cat Part No. HLPTP-95-2M-114/76-ACE-HDG of make Halonix or equivalent make given in Appx BNote :(i) Quoted rates shall be inclusive of excavation, taking down existing pole, all fixing acessories & PCC 1:3:6 for fixing of pole & post top lantern.(ii) Drawing of pole must get approved before installation..(iii) MS pipe of pole (Top & Bottom) should be ISI marked as per latest standard. 33 Supply and fixing in repair PRCD (Portable Residual Circuit Device) Shock safe Plug 16 Amp, 30 mAfor Geyser, complete all as specified and directed by Engineer-in-Charge. Cat Part No. PRCD 16A 30mA of make Havells or equivalent make given in Appx B. 34 Supply and fixing decorative, wall mounting (Bed side light), chrome/brass finish fixture with opal glass diffuser suitable for 2-3 Watt LED including connecting up with two core 1.5 sqmm flexible copper conductor cable, complete all as specified and directed by Engineer-in-Charge. Product SKU -919215850141 of Make Philips or equivalent make given in Appx B. 35 Suply and fixing flexible IP -65 LED strips light in cool / warm white not less than 8 watt per meter along with drivers of suitable size for converting AC into DC, 230 vots, including connecting up with two core 1.5 sqmm flexible copper conductor cable, complete all as specified and directed by Engineer-in-Charge. Cat part No. LED15LST-120LTRI of make Orient or equivalent make given in Appx B. 36 Suply and fixing aluminium channel of size 25X12 mm along with diffuser cover concealed / surface type including necessary arrangement for fixing in wall / ceiling, suitable for fixing flexible LED strips light, complete all as specified and directed by Engineer-in-Charge. 37 Supply and fixing LED Decorative,wall mounting picture light 10-12 Watt, metal body with Opal Glass diffuser including connecting up with driver two core flexible copper conductor, complete all as specified and directed by Engineer-in-Charge. Cat Part No. Metal 12 W Muziris Picture light of Make Philips or equivalentin make given in Appx B. 38 Supply & fixing LED tricolour flexible strip light with IP65 wattage not lesser than 8 watt per meter and roll not lesser than 18 meter with optimum brightness & uniformity of light for perfect cover lighting, including all accessories alongwith fixing on any height, complete all as specified and directed by the Engineer-in-Charge. Cat Part No.LSTRIP-18-SWG-120 of Make Orient or equivalent in make given in Appx B. 39 Supply & fixing LED colourscape light of 80/100 Watt with High intensity color changing & monochromatic compact LED projector with polarized light design & intelligent logarithmic control technology with IP65, including all accessories and PCC 1:3:6 of size 30x30x30cm block for fixing with proper conduit arrangement, complete all as specified and directed by the Engineer-in-Charge. Cat Part No. FC-FL100WRGBMCHof make Orient or equivalent make given in Appx B. 40 Supply and fixingLED post top luminaire 20W- 25W, 5700K, IP-65 made of pressure die-cast aluminium housing & clear glass 240 volt, 50HZ, AC supply completewithall accessories, including electronic driver, internally pre wiredincluding provision of 3 core PVC flexible copper conductor from electric supply source to connector of the light, including disconnecting and taking down existing light fitting and removing old unserviceable fitting, complete all as specified and as directed by the Engineer-in-Charge. Cat Part No.HLPT-S04-20-CW of Make Halonix or equivalentin make given in Appx B. 41 Supply and fixingLED post top luminaire 40W- 45W, 5700K, IP-65 made of pressure die-cast aluminium housing & clear glass 240 volt, 50HZ, AC supply completewithall accessories, including electronic driver, internally pre wiredincluding provision of 3 core PVC flexible copper conductor from electric supply source to connector of the light, including disconnecting and taking down existing light fitting and removing old unserviceable fitting, complete all as specified and as directed by the Engineer-in-Charge. Cat Part No.HLPT-04-45CW of Make Halonix or equivalentin make given in Appx B. 42 Supply and fixing LED high bay/medium bay luminaire 80-90 watt, IP-65,indoor type input voltage range 120-270 volts including electronic driver, provision of 3 core copperconductor cable 1.5 Sqmm size from connector/ceiling rose to fitting with fixing arrangement as per site requirement/conditions and including removing old unserviceable fitting, complete all as specified and as directed by the Engineer-in-Charge. Cat Part No. HLBL-ML-11-80-CWL of Make Halonix or equivalentin make given in Appx B. 43 Supply and fixing LED 22 watt integrated batten fitting with inbuilt lithium ion battery with minimum 4 hour back upincluding removing of unservicable light fitting, complete all as specified and as directed by the Engineer-in-Charge. Cat part No.LED INVERTER BATTENHLB-08-22-CW-INV of make Halonix or equivalent in make given in Appx B. 44 Supplyand fixingLED lamp Invertor technology 9 watt with 4 hour power back up with efficiency more than 100 lumen per watt,Lithium ion battery, complete all as specified and as directed by the Engineer-in-Charge.Cat part No.LED INVERTER LIGHT 10 W B22 CW IP of make Halonix or equivalent in make given in Appx B. 45 Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB.20 Amp, 10 KA B curve including removing old unserviceable enclosure, complete all as specified and as directed by the Engineer-in-Charge.Cat part No. 811955 of make Indo Asian or equivalent in make given in Appx B. 46 Supply and fixing as in repair PCB unit suitable for BLDC ceiling fan of 1200mm sweep single phase, 240 volts of make crompton, Halonix, Havells etc., complete all as specified and as directed by the Engineer-in-Charge. 47 Supply and fixingas in repair modular PVC sheet/cover plate 3 way suitable for fixing switch/socket/fan regulators etc on existing MS boxes of any make as per site requirement including removing unserviceable items, complete all as specified and as directed by the Engineer-in-charge. Cat part No.800063 of make Indo Asian or equivalentin make given in Appx B. 48 All as per above item No. 47 but new 4 module cover plate, complete all as specified and as directed by the Engineer-in-charge. Cat part No.800064 of make Indo Asian or equivalentin make given in Appx B. 49 All as per above item No. 47 but new 6 module cover plate, complete all as specified and as directed by the Engineer-in-charge. Cat part No.800066 of make Indo Asian or equivalentin make given in Appx B. 50 All as per above item No. 47 but new 8 module cover plate, complete all as specified and as directed by the Engineer-in-charge. Cat part No.800067/800068 of make Indo Asian or equivalentin make given in Appx B. 51 All as per above item No. 47 but new 12 module cover plate complete all as specified and as directed by the Engineer-in-charge. Cat part No.800065 of make Indo Asian or equivalentin make given in Appx B. 52 Supply and fixing GI/MS (terminal boxes) rectangular block with earth dolly duly painted internally and externally with two coats of anti corrosive paint over a coat of redoxide including provision of new 3 modular cover plate over sunken box fixed with brass screw and cup washer for mounting, modular switches, sockets outlets, fan regulator etc. , complete all as specified and as directed by the Engineer-in-charge. Cat part No.800063 + 800173 of make Indo Asian or equivalentin make given in Appx B. 53 All as per above item No. 52 but new 4 module cover plate complete all as specified and as directed by the Engineer-in-charge. Cat part No.800064 + 800174 of make Indo Asian or equivalentin make given in Appx B. 54 All as per above item No. 52 but new 6 module cover plate , complete all as specified and as directed by the Engineer-in-charge. Cat part No.800066 + 800176 of make Indo Asian or equivalentin make given in Appx B. 55 All as per above item No. 52 but new 8 module cover plate , complete all as specified and as directed by the Engineer-in-charge. Cat part No.800066 + 800177 of make Indo Asian or equivalentin make given in Appx B. 56 All as per above item No. 52 but new 12 module cover plate , complete all as specified and as directed by the Engineer-in-charge. Cat part No.800065 + 800175 of make Indo Asian or equivalentin make given in Appx B. 57 All as per above item No. 52 but new 1 module cover plate , complete all as specified and as directed by the Engineer-in-charge. Cat part No.800061 + 800172 of make Indo Asian or equivalentin make given in Appx B. 58 Supplying and fixing in repair Thermoplastics IP 65 MCB distribution board 2 way in accordance with IEC 60670-24 which should be shock proof and double insulated. IP65 in accordance with IEC 60529 (EN 60529), weather proof, Corrosion free, Acid & Chemical Resistant, temperature resistance, Made of material Polycarbonate for Lid part andPS (polystyrene) for Base with transparent lid, sealable. halogen & Silicone free recyclable material, .The gasket material shall be Polyurethane, while the gasket shall be internally embedded.The enclosure is Consisting PE and N FIXCONNECT® terminal with provision for cable entry through top, bottom and sides. The impact strength of enclosure i.e. the Degree of Protection against Mechanical load shall be in accordance with IEC 62262 forIK 08 (5 Joule).And Enclosure should withstand Glow wire test at 750°C in accordance with IEC 60695-2-11 flame retardant, Self Extinguishing, UL subject 94,V-2. Color: Grey, RAL 7035.Suitable for indoor installation and outdoor installation, protected against weather influences , complete all as specified and directed by Engineer-in-Charge. Cat part No.KV7103of make Hensel or equivalentin make given in Appx B. 59 Supply and fixing GI D clamp heavy duty superior quality and nut and bolts with locking arrangement for hanging ceiling fan, complete all as specified and as directed by the Engineer-in-charge. 60 Supply and fixing GIfan rod 1000mm long heavy duty withsuperior quality and nut and bolts with locking arrangement , complete all as specified and as directed by the Engineer-in-charge. 61 Supply and fixing heating elementcup or triangle type of 2 KW as required at site for geyser of any make and any descriptions including taking out old unserviceable heating elements , complete all as specified and as directed by the Engineer-in-charge. 62 Supply and fixing thermostat copper switch for geyser of any type ISI marked including taking out old unserviceable thermostat switch, complete all as specified and as directed by the Engineer-in-charge. 63 Supply and fixing geyser inner tank assembly made of steel suitable for geyser capacity of 25 Ltr including taking out old unserviceable tank assembly , complete all as specified and as directed by the Engineer-in-charge. 64 Supply and fixing in repair, heating element, 2 KW, having inbuilt thermostat as required at site for geyser of any make and descriptions , complete, all as specified and as directed by the Engineer-in-Charge. 65 Supply and fixing brass chromium plated non return valve 15mm bore with air lock release arrangementincluding taking out old unserviceable non return valve, , complete all as specified and as directed by the Engineer-in-charge. 66 Supply and replacing metal clad socket & top as per existingsocket and topincluding taking out old unserviceable metal clad socket top, complete all as specified and as directed by the Engineer-in-charge. Cat part No 811955 of make Indo Asian or equivalentin make given in Appx B. 67 Supply and fixing in replacement flexible cable PVC insulated and sheathed,3 core, circular multi stranded copper conductor of 1.50 Sqmmincluding removing unserviceable cable, complete all as specified and as directed by the Engineer-in-charge. 68 Supply and fixing brass connection pipe 600 mm longhaving wire mesh coating over it with brass nuts and washers suitable for connecting geysers inlet and outlet with GI tubings including taking out old unserviceableconnections of any description all as specified and as directed by Engineer-in-charge. 69 Supply and fixingtop plug 15 Amp, 3 pin including taking out old unserviceable plug top , complete all as specified and as directed by the Engineer-in-charge. 70 Supply only flexible cable PVC flat insulated and sheathed,2 core, multi stranded copper conductor of 23/0.76 Sqmmincluding removing unserviceable cable, complete all as specified and as directed by the Engineer-in-charge. 71 Supply and fixing MCB SP, 6-32 Amps, 240 volt,10 KA ,B curve as per site requirement including removing old unserviceable MCB , complete all as specified and as directed by the Engineer-in-Charge. Cat Part No 811008 of make Indo Asian or equivalentin make given in Appx B. 72 Supply and fixing MCB SPN 32 Amps, 240 volt,10 KA ,B curve as per site requirement including removing old unserviceable MCB , complete all as specified and as directed by the Engineer-in-Charge. Cat Part No 811034 of make Indo Asian or equivalentin make given in Appx B. 73 Supply and fixing MCB SPN, 63 Amps, 240 volt,10 KA ,C curve as per site requirement including removing old unserviceable MCB , complete all as specified and as directed by the Engineer-in-Charge. Cat Part No 811154 of make Indo Asian or equivalentin make given in Appx B. 74 Supply and fixing in repairMCB three pole and neutral 415 Volts, 63-100 Amps, 16 KA, 50 Hz thermal adjustable type , complete all as specified and directed by the Eng-in-charge. Cat Part No 811220 of make Indo Asian or equivalentin make given in Appx B. 75 Supply and fixing MCB SP, 40-63 Amps, 240 volt,10 KA ,B curve as per site requirement including removing old unserviceable MCB , complete all as specified and as directed by the Engineer-in-Charge. Cat Part No 811018 of make Indo Asian or equivalentin make given in Appx B. 76 Material and labour for opening the stator & rotor of the 1200mm sweep ceiling fan, cutting the existing worn winding and rewinding the fan withsuperior quality copper wire and filling the varnish as insulation between each winds & covering each loops of winding by sleeves and paper & reassembling of , complete fan by fixing serviceable old and new parts of fans i.e. rubber bush, condenser and shackle housing , gun metal bushes, ball bearings, twin twisted copper cable, down rod assembly & canopy ,split pins , complete all as per manufacturers design air delivery including greasing, oiling & testing of fans all as per manufacturers design & speed , complete all as directed & approved for 1200mm sweep.Notes for item NO (i) to (vii) :- (i). The quoted unit rate shall be deemed to be inclusive of taking out defective parts and fixing of new parts. All new parts shall be measured and paid wide relevant items of the schedule. (ii). The rates for refixing and taking out serviceable parts shall be deemed to be included of quoted unit rates.(iii). New parts shall be of respective makes of fans.(iv). The quoted unit rates shall also include writing of MES No on fans(v). Unserviceable /defective retrieved parts shall be credited under sch of credit.(vi). After assembling all fans shall be tested for the speed as directed.(vii). All the fans shall be repaired/rewind at AGE E/M store yard only. 77 Description allas per serial item No 76 here-in-before but for Exhaust fans of 250/300mm sweep, complete all as specified and as directed by the Engineer-in-Charge. 78 Description allas per serial item No 76 here-in-before but for Exhaust fans of 450 sweep, complete all as specified and as directed by the Engineer-in-Charge. 79 Description allas per serial item No 76 here-in-before but for wall mounting fans of 600mm sweep, complete all as specified and as directed by the Engineer-in-Charge. 80 Supply and fixingas in repairheavy duty wall mounting fan400 mm sweep with corrosion resistant PVC body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotormounted on two ball bearings, aerodynamically contoured blades, rigid frame, PVC blades andtesting , complete all as specified and as directedby Engineer-in-Charge. SKU Code 250552 of make Bajaj or equivalentin make given in Appx B. 81 Supply and fixingas in repairheavy duty exhaust fan 450 mm sweep with corrosion resistant metallic body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings, aerodynamically contoured blades, metallic base framewith rubbermountings for silent operation, 6 pole, maximum watt input not more than 90 watt, 1400 RPM,minimum air delivery 1710 cum/hr with metal blades and shutter type louvers self-openable/ closeble for protecting the entrance of birds as per IS :2132-1967 and testing , complete all as specified and as directedby Engineer-in-Charge. SKU Code 70064 of make Bajaj or equivalentin make given in Appx B. 82 Supply and fixing of heavy duty exhaust fan 300mm sweep with corrosion resistant metal body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings, aerodynamically contoured blades, PVC base framewith rubbermountings for silent operation, maximum watt input not more than 50 watt, 1400 RPM,minimum air delivery 750 cum/hr,metal bladestesting as in repair , complete all as specified and as directedby Engineer-in-Charge. SKU code - 70003of make Bajaj or equivalentin make given in Appx B. 83 Supply and fixing ball bearing No 6201 for 1200/1400mm sweep ceiling fans , complete all as specified and as directed by the Engineer-in-charge. 84 Supply and fixing ball bearingfor 250 to 450 mm sweep Exhaust fans, complete all as specified and as directed by the Engineer-in-charge. 85 Supply and fixing rubber clamp of suitable size for hanging of 1200-1400 mm ceiling fans in 40/50 mm GI pipe,as in repair , complete all as specified and as directed by the Engineer-in-charge. 86 Supply and fixing gun metal bush suitable for 1200/1400mm sweep ceiling fan ,complete all as specified and as directed by the Engineer-in-charge. 87 Supply and fixing in repair fan capacitor 2.5 MFD suitable for 1200/1400 mm ceiling fan, complete all as specified and as directed by the Engineer-in-charge. 88 Supply and fixing sheet metal enclosureVertical triple pole & neutral(VTPN) IP-43 including MCCB 63 Amp, 16 KA, 415 volts, 4 way with 200 Amp rated bus bar flush /surface mounting double door duly grouted in solid block wall or on wooden board in and includinglugs/thimbles duly crimped for connectionincluding making smooth the disturbed surface including removing old unserviceable enclosure , complete all as specified and as directed by the Engineer-in-charge. Cat part No.811888 of make Indo Asian or equivalentin make given in Appx B. 89 Supply and fixing sheet metal enclosuretriple pole & neutral(TPN) 4 way IP-43 with MCB TPN 63 Amp, 16 KA, 415 volts, flush /surface mounting double door duly grouted in solid block wall or on wooden board in and includinglugs/thimbles duly crimped for connectionincluding making smooth the disturbed surface including removing old unserviceable enclosure , complete all as specified and as directed by the Engineer-in-charge. Cat part No.811840 of make Indo Asian or equivalentin make given in Appx B. 90 Supply and fixing in repair,LED Bldg Security Light Fittings of capacity 20-25 watt made up of die castaluminiumhousing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver and making electrical connection, complete all as specified and as directed by the Engineer-in-Charge.Cat part No.ENDURASUNDOWNSL25WLED765PASYBOTGIHD of make Havells or equivalentin make given in Appx B. 91 Supply and fixing sheet metal MCB DB SPN8 way with 200 Amps rated bus bar single pole and neutral with double door IP-43 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure , complete all as specified and as directed by the Engineer-in-charge. Cat part No.811807 of make Indo Asian or equivalentin make given in Appx B. 92 Supply and fixing sheet metal MCB DB SPN 12 way with 200 Amps rated bus bar single pole and neutral withdouble door IP-43 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure , complete all as specified and as directed by the Engineer-in-charge. Cat part No.811808 of make Indo Asian or equivalentin make given in Appx B. 93 Supply and fixing as in repair,MCCB, 4 pole, 63 Amp, 415 Volts, 16 KA , fixedtype including fixing arrangement, complete all as specified and as directed by the Engineer-in-Charge. Cat part No.830020 of make Indo Asian or equivalentin make given in Appx B. 94 Supply and fixing as in repair,MCCB, 4 pole, 100 Amp, 415 Volts, 16 KA , fixedtype including fixing arrangement, complete all as specified and as directed by the Engineer-in-Charge.Cat part No.830022 of make Indo Asian or equivalentin make given in Appx B. 95 Supply and laying as in repair sub main wiring with two run of 4 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 4 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium gradeISI marked of adequate size for housing the wires, complete all as specified and as directed by the Engineer-in-Charge.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. 96 Supply and laying as in repair sub main wiring with two run of 6 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and includingPVC conduit medium gradeISI marked of adequate size for housing the wires, complete all as specified and as directed by the Engineer-in-Charge.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. 97 Supply and laying as in repair sub main wiring with four run of 10 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 10 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and includingPVC conduit medium gradeISI marked of adequate size for housing the wires, complete all as specified and as directed by the Engineer-in-Charge.Note: (i)Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii)Five runs of cable and one run of PVC conduit shall be measured and paid as one unit length. 98 Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty 2 core, 6 sq mm nominal cross section cable with PVC insulated aluminium conductormultistranded served with an inner sheathing of PVC tape and overall PVC sheathed in service connection, including disconnecting and taking down old U/S existingcable, complete all as specified and as directed by the Engineer-in-Charge. 99 Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty 2 core, 10 sq mm nominal cross section cable with PVC insulated aluminium conductormultistranded served with an inner sheathing of PVC tape and overall PVC sheathed in service connection, including disconnecting and taking down old U/S existingcable, complete all as specified and as directed by the Engineer-in-Charge. 100 Material & labourfor earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earthstrip 25 x 3mm thickby means of bolts, nuts, check nuts and washers of galvanised iron.Earth stripprotected by GI pipe 32mm bore(medium grade) and connected to earthing test pointas directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/cboth ways with one handle for liftingmade out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testingas in repair, complete all as directed by Engineer-in-Charge and earth testing on completion . 101 Material & labourfor earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earthwire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to earthing test pointas directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/cboth ways with one handle for liftingmade out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testingas in repair, complete all as directed by Engineer-in-Charge and earth testing on completion . 102 Dismantling the existing lightening conductor from any type of building and refixing the same with new PVC saddles of suitable size complete all as specifed and directed by Engineer-in-charge.Note :- (a)The contractor shall make his own arrangement of scaffolding required for the dismantling or refixing of the lightening conductor. b) The rates includes installation and dismantling scaffolding after completion of Work. 103 Supply and fixing single pointed air termination aluminium rod 12 mm dia, 300mm long, complete all as specified and directed by Engineer-in-charge. 104 Supply and fixing test point terminal block made out of gun metal or phosphorus bronze 75 mm x 25 mm with all accessories, complete all as specified and directed by Engineer-in-charge. 105 Material and labour earth continuity conductor or main earthing lead fixed to wall on battern or recess or chase orburried in ground or drawn in conduit or pipe or fixed to poles or any other indicated situation for loop earthing etc. 25 x 3 mm aluminium strip, complete all as specified and directed by Engineer-in-charge. 106 Material and labour aluminium strip 25 x 3.15 mm with saddles and fixing screws etc. for roof conductors and down conductors above ground, complete all as specified and directed by Engineer-in-charge. 107 Supply and laying as in repair sub main wiring with two run of 1.5 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 1.5 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium gradeISI marked of adequate size for housing the wires, complete all as specified and as directed by the Engineer-in-Charge.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii)Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. 108 Supply and fixing GI/MS rectangular block for mounting, switches, sockets, fan regulators etc. with 3 mm thick plastic laminated sheet cover of size 175 x 100 x 50 mm, complete all as specified and as directed by Engineer-in-charge. 109 Supply and fixing Switch Paino flush type single pole 6 Amps, complete all as specified and directed by Engineer-in-charge. 110 Supply and fixing Switch Paino flush type single pole 16 Amps complete all as specified and directed by Engineer-in-charge. 111 Supply and fixing Socket outlet 2 in 1, 3 pin 6 Amps, complete all as specified and directed by Engineer-in-charge. 112 Supply and fixing Socket outlet 6/16Amps 6 Pin, complete all as specified and directed by Engineer-in-charge. 113 Supply and fixing stepped type electronic fan regulator flush type on the existing laminated sheet etc., complete all as specified and directed by Engineer-in-charge. 114 Supply and fixing as in repair,MCCB, 4 pole, 125 Amp, 415 Volts, 16 KA , fixedtype including fixing arrangement, complete all as specified and as directed by the Engineer-in-Charge.Cat part No.830023 of make Indo Asian or equivalent in make given in Appx B. 115 Supply and fixing Polycarbonate thermoplastics Vertical TPN distributionboard 4 way including MCCB 100 to125 Amp, with breaking capacity 16 kA, in accordance with IEC 61439-3 which should be shock proof, Protection Class-I, earthed. IP65 in accordance with IEC 60529 (EN 60529), weather proof, flame retardent, Corrosion free, Acid & Chemical Resistant, Impact resistant, Ultra Violet resistance, made of halogen and silicon free recyclable material. The DB shall have high grade internally embedded gasket made of Polyurethane ( PUR ) with provision for cable entry through integrated flanges top. The entire system should have hinged door and it can be combination of transparent. complete all as specified and directed by Engr-in-Charge. Cat Part No. FP VN 0400 of make Hensel or Legrand/ Schneider or equivalent make given in Appx B. 116 Supply and fixing in repair uninterrupted power supply system (Inverter) of capacity 1500 volts-ampere, 1260 watts, 50 Hz, input voltage 24 volts, LCD Display complete all as specified and directed by theEngineer-in charge. Make: Luminous/Microtek/Exide/V-Guard. 117 Supply and fixing in repair, connecting and testing 12 Volts, 150 AH tubular battery with lead acid terminals, connection with UPS / inverter battery complete all as specified and directed by theEng-in charge.Cat Part No. RC18000 of make Luminous or equivalent make given in Appx B. 118 Note:-Amount of credit ofRs.1,50,963.00for retrieved materials is mentioned in Schedule of Credit Page No…………………. of tender documents in pdf form which will be deducted offline while acceptance of tender.
