Tender For special Repair To Bldg No P-09, P-10 (03 X Toilet Blocks) And T-60 At Mendhar And Addn/Altn To Toilet Of Bldg No P-94 At Mendhar In The Aor Of Age B/R-I Under Ge 881 Ews-- 1 B/R PORTION: Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed. 2 Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. 3 Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets complete all as specified and directed. 4 Dismantling of timber scantling 40sqcm and over in section unframed work,as in any position, complete all as specified and directed. 5 Taking down chowkhat or frame not exc 1.5 Sqm each with shutters (without taking of shutter from the frames ), complete all as specified and as directed. 6 Taking down chowkhat or frame exc 1.5 Sqm but n exc 4 Sqm each with shutters (without taking of shutter from the frames ), complete all as specified and as directed. 7 Dismantling wrought iron or mild steel work of any description complete all as specified and directed. 8 Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed. 9 M & L 25mm thick PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in sub base and flooring/hardstanding/roof padding etc. complete all as specified. 10 M&L for 75 mm thick cement concrete (1:3:6), type C-2 using 40mm graded stone aggregate as in floors, hard standing etc and laid in alternate bays complete and finished the even & fair and providings joints through out the thickness of plinth protection filed with mastic filling comprising one part of 01 bitumen 85/25 grade and three part of sand by weight all as specified and directed 11 M&L for 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces including finishing even and smooth with out using extra cement complete all as specified and as directed. 12 M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 with mixing of liquid water proofing admixture @ 200 ml/50 kg of cement and finished the surface even and smooth without using extra cement, complete all as specified and directed.Note: WPC shall be measured and paid separately 13 M&L for rendering 5mm thick in cement mortar (1:3) on ceiling surfaces, chajja etc and finishing the surface even and smooth without using extra cement, complete all as specified 14 M&L for complete removal of existing treatement from wall plaster and applying two coats of oil bound distemper white or any tint, over and including 1 mm thick wall care putty, complete all as specified and directed. 15 M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper white or any tint, over and including 1 mm thick wall care putty, complete all as specified and directed. 16 M&L for preparation of newly plastered / unplastered surfaces of wall including cornices pilaster etc, and applying two coats of cement base paint, complete all as specified and directed. 17 M&L for preparation of old plastered/ un-plastered wall surfaces including brooming down or steel wire brushing, scraping down, smoke soot, mould, moss, efflorescent salts, trading oil and greasy spots, and applying two coats of cement base paint, complete all as specified and directed. 18 M&L for providing and fixing in true horizontal level 600mm x 600mm, false ceiling system hot dipped galvanised steel section, exposed surface with pre-coated capping, main tee of size 24 x 38 mm, having 0.25mm gauge at every 1200 mm centre to centre maximum and rotary stitched cross tee of size 24 x 38 mm having 0.25 mm gauge at every 600mm c/c and sub cross tee of size 24 x 38mm, having 0.25 mm gauge at 1200 mm c/c and wall angle of size 19 x 19mm, having 0.35mm gauge fixed to the periphery of the wall. The above grid is suspended at every 1200 mm c/c in both directions using 2.0mm thick pre-straightened Gl wire, laying calcium silicate fissured pattern semi perforated butt edge ceiling tiles of size 600mm x 600mm x 6mm having thermal conductivity K=0.15 W/m.K, having fire performance(BS-476), complete all as specified and directed by Engr-In-Charge. 19 M&L for Pressed steel frames for doors for size 125 x 60mm, made of 1.25 mm thick sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc. incl filling frame with PCC 1:3:6, type C-1, complete all as specified and as directed. 20 M&L for Mild steel work as in hand rails, half round or other stock section or core for wooden hand -rail, straight portion drilled and countrsunk for ballusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screqing etc. wind ties for roof including securing bolts, posts and struts in fencing including cuttings, tops to shapes, as directed, drilling, holes, notching for wire etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc. fixed in repairs, and similar work conforming to Fe-250 Gde E-165, complete all as specified and directed. 21 S & F 35mm thick 2nd class hard woodglazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc divided into squares with plain chamfered or rounded, mitred and rebated shash bars, any numbers, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a), supplied & fitted to chowkats, complete as specified and directed. 22 S & F 35 mm thick 2nd class hard woodplain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board, medium density, wood particle board with commercial face veneered supplied & fitted to chowkat, complete as specified and directed. 23 S & F 200mm long aluminium, anodised, barrel tower bolts of extruded section and fixed, complete all as specified & directed. 24 S& F 150 mm long aluminium handles, cast type, anodised and fixed, complete all as specified & directed. 25 S&F Small fittings 2nd class such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours, articles n exc 200 cu. cm each complete all as specified and directed. 26 S & F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified & directed. 27 S & F in repair stainless steel wire cloth, 0.71 mm nominal dia of wire and average width of aperture 1.20mm and fixed withtinned tacks or stainless steel wire staple, complete all as specified and directed. 28 M&L for preparation of wood and wood based surfaces of any description not otherwise described over 10 cms width or girth and applying 2 coats of synthetic enamel paint over a coat of pinkprimer, complete all as specified and directed. 29 M&L for preparation of new steel & Iron surfaces, width or girth exceeding 10cm & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer, complete all as specified & directed. 30 M&L for preparation of old steel & Iron surfaces, width or girth exceeding 10cm & applying two coats of synthetic enamel paint of 1st quality, complete all as spd & directed. 31 M&L for providing and fixing of double rebate openable/fixed windows made of galvanized steel, colour coated/powder coated (base steel as per IS 513 of “D quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with a total thickness of coating 0.58 mm, the surface shall be primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 72 x 55 mm, centre mullion section 72 x 50 mm,shutter section 47 x 20 mm, fly mesh section 40 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall have a rebate for glazed shutter, fly mesh and a 20 mm provision for guard bars/grills,the sections shall be cut to length, mitre joined with corner bracket, centre mullions fixed with mullion cap, stay, handles, latch, 2 Nos of heavy duty stainless steel pivot hinges per shutter and shutter shall be panelled with 5mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing windows in the concrete/masonry wall by means of self-expanding screws, including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch)etc. complete as per the direction of Engineer in Charge. 32 S & F 300 mm, mild steel helical door spring, stove enamelled black, including roller and roller plate complete, complete all as specified & directed. 33 S&F decorative curtain rod 25 dia with decorative head on both end of rod and necessary clamps / fixing brackets, stops, rollers etc complete all as specified and as directed. 34 M & L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base of floor, foundation , filling mass concrete etc complete all as specified. 35 M&L for walling of random rubble stone masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed. 36 M&L for walling of random rubble stone masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6) but except stone,complete all as specified and directed. 37 M&L for raised pointing to random rubble masonary, or polygonal rubble, uncoarsed or brought upto courses in cement mortar 1:3, complete all as specified and directed. 38 Supply only liquid water proofing admixture complete all as specified and directed. 39 Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed. 40 M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. 41 M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 42 Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed 43 Taking up or down 15mm bore steel tubing & connection including cleaning for or removal from site 15mm, complete all as specified and directed. 44 Taking up or down 20mm bore steel tubing & connection including cleaning for or removal from site 15mm, complete all as specified and directed. 45 M&L for 50 mm thick cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in floors, hard standing etc and laid in alternate bays complete and finished the even & fair and providings joints through out the thickness of plinth protection filed with mastic filling comprising one part of 01 bitumen 85/25 grade and three part of sand by weight all as specified and directed 46 M&L for preparation of new plastered surfaces and applying three coats of white wash, complete all as specified and directed. 47 M&L for preparation of old plastered surfacesof walls and applying two coats of white wash, complete all as specified and directed. 48 M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling, complete all as specified and directed. 49 M&L for preparation of old plastered surfaces and applying two coats of white wash on ceiling, complete all as specified and directed. 50 S&F bathroom mirror cabinet plastic body white coloured, wall mounted type of size 47.4 cm x 37.60 cm x 19.20 cm, (min weight 3.2 kg), rectangular shaped, complete all as specified and as directed. 51 M&L for glazed ceramic colouredtilesof size450 mm x 300 mm x 7mm thick as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tileincludingbacking layer of 10 mm thick in cement mortar 1:4 complete all as specified and directed. Shade/Colour of tile shall be approved by the GE. 52 M&L for coloured Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 10 mm thick in cm 1:4for laying floor finishes, complete all as specified and directed. 53 S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with ms square tube suppling and fixing in opening as per specification & drawing. 54 S&F Factory made solid panel PVC door shutter 30mm thick(Stiles) consisting of frame made out of MS tubes for top and bottom rails. MS frames shall be covered with heat moulded plain coloured PVC,C, channel having PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail.Panelling of plain colour PVC sheet to be fitted in the MS frame with 3 Nos stainless steel hinge 100 mm size, welded/sealed to the stiles rails with suitable PVC sheet beading and jointed together with solvent cement, fixed in the frame complete all as per manufacturers instructions. 55 S & F 100 mm long aluminium alloy butt hinges with galvanised mild steel hinge pin type, C-21, complete all as specified & directed. 56 S&F Steel ventilator with top hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified. 57 S&F GI tubing medium grade 15mm diawith all fittings, cutting, threading and fixing to walls,ceilingor in floors, complete all as specified and directed. 58 S&F GI tubing medium grade 20mm diawith all fittings, cutting, threading and fixing to walls, ceilingor in floors, complete all as specified and directed. 59 S&F rotational moulded polyethylene water storage tankstriple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I,of capacity1000 Ltrs, complete, screwed for iron pipe or brass ferrule and fixed, incl dismantling of existing water tank, complete all as specified and as directed. 60 S&F rotational moulded polyethylene water storage tankstriple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I,of capacity500 Ltrs, complete, screwed for iron pipe or brass ferrule and fixed, incl dismantling of existing water tank, complete all as specified and as directed. 61 S&F in repair Vitreous china wash down water closet pan (Pedestal pattern) white (excluding flushing cistern and flush pipe) , plastic water closet seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised or PVC hinging device complete all as specified and directed. 62 S&F in repair PVC valve less syphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints complete all as specified and directed. 63 S&F in repair 15mm bore dia bib taps, fancy type, with chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed. 64 S&F in repair 15 mm bore dia stop valve/angle cock, fancy type, with chromium plated cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed down both ends for iron pipes or for unions and fixed with butter fly handle, complete all as specified and directed. 65 S&F in repair 15 mm bore dia stop valve/angle cock, two way with chromium plated cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed down both ends for iron pipes or for unions and fixed with butter fly handle, complete all as specified and directed. 66 S&F in repair telephonic hand shower (Health faucet) (ABS Body) MS chromium plated suitable forlongmm dia pipe with 1.25 mtr long flexible tube in chrome finish and ABS wall hook, complete all as specified and directed. 67 S & F in repairs Stainless Steel Wall Mount Case with Soap Holder & Brush Holder fixed to wall all as specified and directed by Engr-in-Charge. 68 S&F in repair 600mm x 450mm size bevelled edge mirror with border, selected quality 5mm thick glass mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engineer-in-Charge. 69 S&F in repair 15mm bore brass CP wall mixer fancy type with provision for overhead shower for mixing hot or cold water, screwed for iron pipe , complete all as specified and directed. 70 S&F in repair chromium plated shower rose 125 mm size, with or without swivel joints, incl fixing to steel pipe or union, complete all as specified and directed. 71 S&F in repairs towel rail 600mm long 20mm dia brass chromium plated fixed with wooden gutties embedded in cementmortar (1:3) with MS screws etc, complete all as specified and directed. 72 S&F in repairs flexible waste pipe for wash hand basin, incl all necessary fittings, complete all as specified and directed. 73 Supply & Fix in repair PVC connection pipe 600 mm long, both end screwedfor water cooler complete all as specified and directed. 74 S&F in repair waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms) for 32mm bore dia of discharge pipe to WHB, sink, complete all as specified. 75 S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm widewith chromium plated bracket guard and railing 60cm long,complete all as specified and directed by Engr-in-Charge. 76 S&F Nipple suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm-45gms /25mm- 65gms) complete all as specified and directed. 77 S&F in repairGun metal lever type gate valves high pressure with polythene float and fly nut complete screwed for iron pipe or for unions of 20 mm bore, complete all as specified and directed. 78 S&F in repair 20 mm bore ball brass valves high pressure,high pressure with polythene float and fly nuts complete, screwed for iron pipe or brass ferrule, complete all as specified and directed. 79 S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed 80 S&F in repair PVC (SWR) bends of any radius 75mm dia, complete all as specified and directed. 81 S&F in repair PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe/weep holes etc including clamps, complete all as specified and directed. 82 S&F in repair PVC (SWR) bends of any radius 110mm dia, complete all as specified and directed. 83 S&F in repair PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe including clamps, complete all as specified and directed. 84 M&L complete removal of existing water proofing treatment including coved fillets and removing demolished material to a distance exc 50 m, complete incl dismantling existing lightening conductor and refixing in same location incl repair/replacement conductor damaged during the work of roof treatment, complete all as specified and directed. 85 M&L for rougheningof roof surface after complete removal of existing treatment & brushing with neat cement slurry @ 3 Kg per sqm area, complete all as specified and directed. 86 M&L for 15mm thick screed bed or bedding layer in cement mortar (1:4) with mixing ofwater proofing compound @ 200ml/50 kg of cement on green surface of concrete andfinished the surfaces even and fair, complete all as specified and as directed. (NOTE : Supply only WPC shall be measured and paid separately under relevant item of this Schedule A). 87 M&L for applying a tack coat of bitumen @ 1.2 kg/sqm of paving grade butumen Vg 20 (60-80 penetration) over a coat bitumen primer @ 0.40Ltr/Sqm including cleaning the surface,complete all as specified and directed. 88 M&L for providing APP based polymeric membrane minimum weighing 3.60kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 200 gms/sqm) laid on bitumen surface by forced application and inserting in groove above 15cm from roof and including applying bitumen Vg20 paving grade (60 to 80 penetration) @1.20Kg/Sqm & blinded with fine dry sand @0.50Kg/Sqm including testing, complete all as specified and directed. 89 S&F in repair 15mm bore dia pillar tap, fancy type with chromium plated cast copper alloy with flynut, capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed without lettered hot or cold, complete all as specified and directed. 90 S&F in repair vitreous china urinals, half stall type of size 465x355x265mm white (minimum) with CPurinal spreader and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with automatic flushing cistern with brackets, flush pipe, waste pipe grating and union for discharge pipe complete all as specified and directed. 91 S&F Vitreous china urinal partition white of size 310x700 mm complete all as specified and directed. 92 M&L for Plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified and directed. 93 M&L for vitrified double charged ceramic tiles 8 to 9 mm thick light shade, area of each tile not exceeding 0.36sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:4), complete all as specified and directed. 94 All as per item No 93 above but on skirting/dado etc over and incl 10 mm thick rendering in CM 1:4, complete all as specified and directed. 95 M&L for preparation of old/new wood and wood based surfaces of any description not otherwise described over 10 cms width or girth and applying 2 coats of creosote oil, complete all as specified and directed. 96 S & F 150 mm long aluminium alloy butt hinges with galvanised mild steel hinge pin type, C-21, complete all as specified & directed. 97 M&L for Pressed steel frames for doors for size 105 x 60mm, made of 1.25 mm thick sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc. incl filling frame with PCC 1:3:6, type C-1, complete all as specified and as directed. 98 S&F in repair Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, white, with integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and anti syphonage pipe etc, complete, all as specified and as directed. 99 S&F in repair wash hand basin of counter type vitreous china of oval shape of size 515 x 415 x 145 mm (excluding taps, waste, chain and plug and porcelain stopper but exclusive of fixing of supply and waste pipe, complete all as specified and as directed. 100 S&F in repair PVC (SWR) Tees, suitable for 75mm dia pipe, complete all as specified and directed. 101 S&F in repair PVC (SWR) Tees, suitable for 110mm dia pipe, complete all as specified and directed. 102 Brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4, complete all as specified. 103 Demolition of roof, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, complete all as specified and directed. 104 M&L for RCC design mix M-25 as in slab supported on walls, beam etc, incl 5 mm thick plastering on top of the roof surface in CM 1:3, complete all as specified and directed. 105 Form work to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for rough finished surfaces of concrete, complete all as specified and directed. 106 Formwork to edges of concrete floor slab, landing and similar work not exceeding 20cm thick, complete all as specified and directed. 107 M&L for TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified. 108 M&L for TMT bars, 6 to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified. 109 M&L for TMT bars, 5mm dia and over upto incl 10mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia as in stirrups, complete all as specified 110 M&L for galvanised corrugated steel sheet 0.63mm thick of any colour with two corrugated side lap, fixed with screws and washers in roof, wall etc with L type or J type or cranked hook bolts wherever required, complete all as specified and directed. 111 M&L for galvanised plain steel sheet 0.63mm thick of any colour with two corrugated side lap, fixed with screws and washers in roof, wall etc with L type or J type or cranked hook bolts wherever required, complete all as specified and directed. 112 M&L for rolled mild steel works as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam,tee,angle, channel or flat sections) including distance pieces, cleats etc Fe 290(Gde E 165),complete all as specified 113 M&L for preparation of new steel & Iron surfaces, width or girth exceeding 10cm & applying two coats of synthetic enamel paint of 1st quality, complete all as specified & directed. 114 M&L for 20mm thick granite (of approved type colour) work (table rubbed & polished) in jambs, pillars, window cills, cooking plateform laid over and including 15mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the colour of granite stone including cutting and and moulding the edges, complete all as specified and directed. 115 Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed. 116 S&F in repair Stainless steel sink 1mm thick with drainage board for kitchen or laboratory wih plugs, washers and wastes including fixing bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mmx460mm bowl size 410mmx330mmx160mm fixed, with LDPE waste pipe and waste coupling, complete all as specified and directed. 117 Surface excavation not exceeding 30cm deep and average 15cm deep and getting out in any type of soil, complete all as specified and directed. 118 S&F in repair Stainless steel sink 1mm thick with drainage board for kitchen or laboratory wih plugs, washers and wastes including fixing bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mmx460mm bowl size 410mmx330mmx160mm fixed, with LDPE waste pipe and waste coupling, complete all as specified and directed. 119 M & L for PCC 1:2:4 type B2 (using 40 mm graded stone aggregate) as in sub base and flooring etc. complete all as specified. 120 M&L for RCC M-25 (design mix) using 20mm graded crushed stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases of columns etc. complete all as specified and directed by Engineer-in-Charge. 121 Form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to better with rough finished surfaces of concrete complete all as specified & directed 122 M&L for RCC M-25 (design mix) using 20mm graded crushed stone aggregate as in columns, piers, posts and struts etc. complete all as specified and directed by Engineer-in-Charge. 123 Form work to sides of pillars, posts, struts piers, columns and stanchions and similar works fair finished surface of concrete complete all as specified & directed by Engineer-in- charge. 124 M&L for RCC M-25(design mix) using 20mm graded crushed stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed 125 Form work to sides and soffits of floor or roof beams, girders, bressummers,lintels etc for rough finished surface of concrete complete all as specified & directed by Engineer-in- charge. 126 Removal of excavated material to a distance exc. 250 m but not exc 500 m and depositing where directed at a level not exceeding 1.5 mtr above starting point, complete all as specified and directed by Engineer-in-charge. 127 M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed. 128 M&L for 10mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces including finishing even and smooth with out using extra cement complete all as specified and as directed. 129 Material & Labour for preparation of new plastered surfaces and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm, complete all as specified and as directed. 130 S & F powder coated aluminium ventilator cross section conforming to IS 63.5x38.10x1.5mm consisting of two portions, upper portion shall have louvers with 3mm thick pin headed glass and aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56m fixed with aluminium beads and securing on outer face of frame and lower portion of ventilation shall be fixed with 3mm thick pin headed glass with IDPE rubber gasket including aluminium beads, including preparation of jambs all around in CM 1:3, finishing even and smooth complete all as specified and directed. 131 Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level), complete all as specified and directed. 132 M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring/path etc. finished even & fair, complete all as specified and directed. 133 S&F in repair PVC (SWR) 110 mm dia vent cowl suitable for pipes, complete all as specified and directed. 134 S&F in repair vitreous China wash down water closet pan (pedestal pattern) rimless one piece EWC with slim soft close seat cover 660 x 350 x 745 mm concealed Sor P trap for better aesthetics snow white, complete all as specified & directed.Make: CERA cat part No S1013230 or its equivalent make as approved by GE 135 S&F in repair mild steel chromium plated grating (round) 125 mm dia fixed over floor/nahani trap, complete all as specified and directed. 136 Cutting upto a depth of 2.5cm into concrete walls and trimming surface as required,girth exc. 30cm with or without reinforcement, complete all as specified and directed. 137 Cutting into existing manholes for connecting new drain pipes of internal dia of pipe150mm, making good to pipe and rendering as required, cutting out existing benching for and forming branch channeling in cement concrete 1:2:4 type B1, and making good the existing benching, complete all as specified and directed. 138 Supply and laying of NP 2RCC pipes 150mm bore, laid and jointed complete with collar per length of pipe, complete all as specified and directed. 139 M&L for PCC bed to drain pipes including packing under and haunching against the sides of pipes for 150 mm bore after they are laid and tested in PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed. 140 S & F 150mm long aluminium, anodised, barrel tower bolts of extruded section and fixed, complete all as specified & directed. 141 M&L for providing reinforced cement concrete, 1:2:4 type B1 using 20mm graded stone aggregate as inprecast cover slabs for manholes and drains including necessary use of formwork and set in cement mortar 1:4,complete all as directed and specified. 142 S & F Solid PVC Wall Lining consisting of 5mm thick wood grainprinted PVC sheet inclusive of solvent cement and fixing at site all as per specifications and drawing, complete all as specified and directed. 143 S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive offixing on to wall to make PVC Frame as per specification and drawing 144 Supplyingandinstalling vanishing blinds with Vinyl coated fibreglass fabric laminated with two-ply 100% PVC blackout film (of Revolving Blackout Type and grade 2000 series with RB-07 of SD Blinds and having same colour, shade and texture). Fire classification of fabric NFPA 701-2004 (small scale), BS 5768-2008 Part 2 Type B Performance Fabric should be Bacterial & Fungus fee, Green guard & Lead free, normal thickness of fabric shall be 0.50mm and minimum weight 255gsm, excellent hanging properties and very high tear strength. The fabric shall be suspended from the top channel made up of extruded alloy of 1.25mm nominal thickness and 38mm nominal diameter. The top channel shall be fixed with powder coated mild steel bracket with clutch assembly on either end of blind, fixed to jambs of the window opening with 50 mm stainless steel screw with nylon roll plug and to the aluminium window with 25mm self thread screw. The operating mechanism shall be operated with plastic ball chain having 4.50 mm balls made of ABS plastic linked with 1.50 mm polyester cord. The mechanism shall allow the blind to stop in desired position with the clutch mechanism. The bottom channel shall be made of rectangle shape with extruded aluminium tube with powder coating. The fabric shall be enclosed in suitably created pocket along the tubes, which shall be closed from side with end caps of same colour to the bottom roller. All exposed components of roller blind shall be of milky white colour, complete all as specified and directed. 145 E&M PORTION:-Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed. 146 M&L for point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cableand one single core 1.5 Sqmm(nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :- 147 One light/fan point controlled by one way switch 6 Amp complete all as specified and directed. 148 One 3/5 pin socket outlet 6 amp on same board complete all as specified and directed. 149 One 3/5 pin socket outlet 6 amp independent board complete all as specified and directed. 150 All as per srl item No 146 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 2.5 Sqmm as in continuous earth wire complete all as specified and directed. 151 S&F Sub main wiring with single core cable 2x 4 Sqmm FRLSinsulated unsheathed stranded copper conductor cable 1100 Volts grade including suitable size PVC casing cappingmedium grade ISI marked alongwith 1x 4 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, incl dismantling old wiring and making good the surface by plastering and 2 coats of existing paint/colour complete all as specified and directed.Note:-Three wire of 4 sqmm and one run of PVC conduit/casing caping shall be measured as one unit. 152 S&F switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed. 153 S&F socket outlet2 in 1, 3 pin, 5 Amp flush type universal, complete all as specified and directed. 154 S&F switch piano flush type 15 Amp single pole one way, (ISI marked), complete all as specified and directed. 155 S&F socket outlet2 in 1, 3 pin, 15 Amp flush type universal, complete all as specified and directed. 156 S&F ceiling rose, 3 terminal, surface bakelite 65 mm x 50mm, PVC/poly carbonate, insulated body, complete all as specified and directed. 157 S&F Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed. 158 S&F LED inverter lamp,CDL, 9/10 watt, B22 base, complete all as specified and directed. 159 S&F stepped type electronic fan regulator, 100 watt capacity, complete all as specified and directed. 160 Supply and fixing in repair inverterLED batten 1x 20W, with square profile and polycarbonate channel, lithium iron battery with charging time of 8 to 10 hours and backup tile upto 04 hourswith driver, holder incl LED tube light connecting up with with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 161 Supply and laying 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat or circular of size 10 Sqmm& including taking down old old unsv service cable connection, complete all as specified and directed. 162 Supply and fixing in repair LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. 163 S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 8 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed. 164 S&F in repairMCBSPN 63 amps 240 volts 10 KA B curve, finger proof terminal, bi-connect termination, label holder, 35 Sqmm terminal capacity, insulating sliding shutter large two position dolly, ISI marked, complete all as specified and directed. 165 S&F in repairMCBSPN 40 amps 240 volts 10 KA B curve, finger proof terminal, bi-connect termination, label holder, 35 Sqmm terminal capacity, insulating sliding shutter large two position dolly, ISI marked, complete all as specified and directed. 166 S&F in repairMCBSP 6 to 32 amps 240 volts 10 KA B curve, finger proof terminal, bi-connect termination, label holder, 35 Sqmm terminal capacity, insulating sliding shutter large two position dolly, ISI marked, complete all as specified and directed. 167 S&F heavy duty metallic exhaust fan 300 mm sweep 1400 RPM, single phase 230 Volts including all connecting accessories, complete and taking out old existing exhaust fan, complete all as specified and directed. 168 Supply and laying, jointing and testing, 1100 volts grade armoured, heavy duty XLPE electric cable with aluminium conductor of size 16 Sqmm 4 core, laid in trenches/on floor/pole or under road/culvert incl taking out old unsv cable, complete all as specified and directed.Note: Excavation shall be measured and paid separately 169 Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth in any type of soil, complete all as specified and directed by Engineer-in-charge. 170 Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.Note : Punned down thickness shall be measured 171 Removal of excavated material to a distance not exc. 50 m and depositing where directed at a level not exceeding 1.5 mtr above starting point, complete all as specified and directed by Engineer-in-charge. 172 M&L for sand cushioning to UG cable 8 cm thick before laying and 15cm thick after laying complete all as specified and directed.Note:- 1.Dry fine sand of best available quality shall be used.2.Punned thickness shall be made and paid. 173 Supply and laying sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed. 174 M&L for making bore to road/cement path/hardstanding/road for providing GI pipe 40 mm, both end socketed for passing armoured cable, incl making good the surface light grade galvanised with all fitting and fixed to wall/ceiling or laid in floor complete all as specified and directed. 175 S&F in repair tubes 40 mm, light grade galvanised with all fitting and fixed to wall/ceiling or laid in floor complete all as specified and directed. 176 S&F in repair MCCB 63 Amps, 4 pole, 16 KA, complete all as specified and directed. 177 Supply and fixing energy efficientLED light fitting 35 W, input voltage 110V to 280VAC, 50 Hz with ingress protection IP66, LM 80, standard luminaries with efficiency 100 lumen/watt with secondary optics, perfectly matched lenses, complying to IEC60598/IS10322, with auto shut down on high voltage, CRI>70,PF>0.95, with short circuit & reverse circuit protection against10kV high surges, minimum 25000 burning hours (life), operating temperature 1 to 50oC, rectangular shape with pressure die cast aluminium housing with weather proof gasket for lamp and driver compartment with system wattage of 45W=10%W, rated lumens, 120 degree view angle, constant current type driver having THD<10%, including all fixing arrangement like clamps, nuts, bolts, washers, 45W LED rod lamp (having PF>0.9, input voltage 90-300V, IP-66, LM80) with all accessories pre-wired and connecting with twin core twisted flexible copper conductor cable with all necessary staging, etc. including bracket complete all as specified and as directed. 178 Supply and fixing energy efficientLED light fitting 45 W, input voltage 110V to 280VAC, 50 Hz with ingress protection IP66, LM 80, standard luminaries with efficiency 100 lumen/watt with secondary optics, perfectly matched lenses, complying to IEC60598/IS10322, with auto shut down on high voltage, CRI>70,PF>0.95, with short circuit & reverse circuit protection against10kV high surges, minimum 25000 burning hours (life), operating temperature 1 to 50oC, rectangular shape with pressure die cast aluminium housing with weather proof gasket for lamp and driver compartment with system wattage of 45W=10%W, rated lumens, 120 degree view angle, constant current type driver having THD<10%, including all fixing arrangement like clamps, nuts, bolts, washers, 45W LED rod lamp (having PF>0.9, input voltage 90-300V, IP-66, LM80) with all accessories pre-wired and connecting with twin core twisted flexible copper conductor cable with all necessary staging, etc. including bracket complete all as specified and as directed. 179 S&F Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 6mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion including dismantling unsv earthing whereever required, complete all as specified and directed. 180 Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. all as specified and directed. 181 S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 4 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed. 182 Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc, complete all as specified and directed. 183 M&L for providing opening and grouting with nuts and bolts for fixing of exhaust fan in wall incl civil work as required on site and making good the disturbed surface, complete all as specified and directed. 184 Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified. 185 M&L for rewinding of ceiling fan 1200 mm sweep with existing gauge of copper winding wire as well as number of turns and ressembling the fan after replacing the unserviceable spares like bushes , shafts, fasteners, bearings, capacitors and flexible cord for putting fan in serviceable condition incl refixing the same after carrying out necessary repairs to original place, complete all as specified and directed. 186 M&L for painting to ceiling fans and marking of MES number on fans in situ with synthetic enamel paint by spraying incl filling cavities with filler, one coat after cleaning all dust etc,complete all as specified and directed. 187 Taking out old unsv ceiling fan from site of capacity 1200/1400 mm sweep and replacement withceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep, min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)incl all connecting accessories complete all as specified and directed by Engineer-in-charge. 188 S&F switch piano modular type, flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed. 189 S&F switch piano modular type, flush type 15 Amp single pole one way, (ISI marked), complete all as specified and directed. 190 S&F socket outletmodular type, 3 pin, 5 Amp flush type universal, complete all as specified and directed. 191 S&F socket outletmodular type, 3 pin, 15 Amp flush type universal, complete all as specified and directed. 192 S&F modular cover plate with frame for 3 module, complete all as specified and directed. 193 S&F modular cover plate with frame for 4 module, complete all as specified and directed. 194 S&F modular cover plate with frame for 8 module, complete all as specified and directed. 195 S&F modular metal flush box, 3 module, complete all as specified and directed. 196 S&F modular metal flush box, 4 module, complete all as specified and directed. 197 S&F modular metal flush box, 8 module, complete all as specified and directed. 198 S&F sheet metal enclosure for DBs, SPN double door (IP43), 8 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed. 199 S&F MCBSPN 40 amps 240 volts 10 KA B curve, finger proof terminal, bi-connect termination, label holder, 35 Sqmm terminal capacity, insulating sliding shutter large two position dolly, ISI marked, complete all as specified and directed. 200 S&F MCBSP 6 to 32 amps 240 volts 10 KA B curve, finger proof terminal, bi-connect termination, label holder, 35 Sqmm terminal capacity, insulating sliding shutter large two position dolly, ISI marked, complete all as specified and directed. 201 S&F in repair single pole and neutral enclosure with a two pin and metal earth plug and socket complete with & incl one single pole MCB of 20 Amps complete all as specified and directed.
