Tender For special Repair To Bldg No. P-18/01 To 07 (Jcos Md Accn) In Zone-I Area Under Ge Jaipur At Jaipur Mil Stn-- 1 Taking down cement plaster or cement lime plaster, any description on brick, stone walls or concrete surface of ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed 2 Raking out joints/pointing to random rubble or polygonal rubble uncoursed or brought up to courses walls or to stone on edge in floors etc built in cement or lime mortar& removing rubbish outside MoD land complete all as specified and directed 3 Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15cm thickness (below or above ground level) complete all as specified and as directed 4 M&L for keyed pointing to random or polygonal rubble, uncoursed or brought upto courses inCM 1:4 on stonemasonry surfaces complete all as specified and directed. 5 M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick masonry surfaces or concrete surface of wall finished even and smooth without using extra cement complete all as specified and directed. 6 M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick masonry surfaces or concrete surface finished even and smooth without using extra cement complete all as specified and directed. 7 M&L rendering 15mm thick in CM 1:4 on stone masonry surfaces or on surface other than fair faces of brick masonary finished even and smooth without using extra cement complete all as specified and directed. 8 M&L for rendering 15 mm thick in two layers, 1st layer 10 mm thick in CM 1:4 and IInd layer 5 mm thick in CM 1:4 incl mixing of WPC as per manufacturers instruction, on stone masonry surfaces or on surface other than fair faces of brick masonary, finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.Note : WPC shall be measured and paid seperately 9 M&L rendering 5 mm thick in CM 1:3 as on concerete surface of ceilings finished even and smooth without using extra cement complete all as specified and directed . 10 M&L Dubbing out average 10 mm thick on irregular face of walls/ceiling floating/ setting coat in CM 1:4 all as specified and as directed 11 M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over one coat of primer over 2mm thick wall care putty to make smooth the surfaces incl rubbing all as directed by Engineer-in- Charge. 12 M&L for complete removal of existing treatment on walls and applying two coats of oil bound distemper over one coat of primer over 2mm thick wall care putty to make smooth the surfaces incl rubbing all as directed by Engineer-in- Charge. 13 M&L for preparation of new plastered surfaces of walls and applying two coats of premium exterior emulsion weather proof paint (ready mix) of approve shade and tint using hand roller over one coat of primer over 2mm thick wall care putty to make smooth the surfaces incl rubbing all as directed by Engineer-in- Charge. 14 M&L for complete removal of existing treatment on walls and applying two coats of premium exterior emulsion weather proof paint (ready mix) of approve shade and tint using hand roller over one coat of primer over 2mm thick wall care putty to make smooth the surfaces incl rubbing all as directed by Engineer-in- Charge. 15 M&L for preparation of newly plastered surfaces of ceiling and applying two coat of oil bound distemper over 2 mm thick of wall putty complete all as specified and directed. 16 M&L for complete removal of existing treatment on ceiling and applying two coat of oil bound distemper after application of 2 mm putty and one coat of primer complete as specified and directed. 17 M&L for prepartion of keyed pointing to random or polygonal rubble and applying two coats of premium exterior emulsion weather proof paint (ready mix) of approve shade and tint using hand roller over one coat of primer complete all as specified and directed. 18 Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises complete all as specified and directed. 19 M&L for joint free coloured non skid ceramic tiles, 7 to 8mm thick (Square/rectangular) area of each tile 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed 20 M&L for joint free coloured non skid ceramic tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. 21 M&L for joint free coloured non skid ceramic tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement match the shade of tiles over and including 10 mm thick wall plaster in CM 1:4 complete all as specified and directed 22 M&L for joint free coloured non skid ceramic tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed. 23 M&L for joint free coloured non skid ceramic tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement match the shade of tiles over and including 10 mm thick wall plaster in CM 1:4 complete all as specified and directed 24 M&L for coloured Glazed ceramic tiles 300 x 450 x 7mm thick on vertical surfaces such as skirtings, dados and risers to steps etc,. set and jointed in neat cement slurry and pointed in white or coloured cement to matchthe shade of tiles over and including 10mm thick rendering in CM 1:4 complete all as specified and directed . 25 Demolition of stone slab and tiles of any description or thickness in floor aprons etc laid beded and pointed in any mortar complete all as specified and directed . 26 M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over 15mm thick screed bed in CM 1:4 complete all as specified and directed. 27 M&L 18-20 mm thick kesaria Green marble (table rubbed & polished) in cooking platforms & edges in and like in CM 1:4 incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed . 28 M&L for 20mm marble slab (machined polished) as in verticalpartitions, below kitchen cooking plat form and raised platform of kitchen complete all as specified and directed . 29 M & L 25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in floors complete all as specified and directed. 30 M&L 15 mm thick screed bed or bedding layer in cement mortar 1:6for laying floor finishes /tiles /kota stone etc complete all as specified and directed. 31 M&L for machine cut kota stone slab flooring 20-25mm thick of size 550 x 550 mm in floor over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and granite polishing complete all as specified and directed . 32 M & L Machine cut kota stone slab flooring 20-25mm thick in single piece fixed in cupboard partion including rubbing and polishing complete all as specified and directed. 33 M & L machine cut kota stone slab 20-25mm thick on vertical surface of wall, riser, steps, skirting, dado and pillar etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10 mm thick cement plaster in CM 1:4 including rubbing and polishing complete all as specified and directed 34 M&L for Rounding to edges of stones slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed. 35 S & F in repair 18 mm thick WPC board one side white laminate and other side decorative as in kitchen cabinetsfixed with minifix hardware where ever required including edge band 22 mm wide 0.80 m thick of matching colour on exposed surfaces of board fixed with polymaster adhessiveincluding trimming edges of edge band to true line of thicknesss of board by manual trimmer complete all as specified and directed. 36 S & F in repair 8 mm thick WPCboard one side white laminate and other side undecorative as in back of kitchen cabinets complete all as specified and directed. 37 S & F kitchen plain baskets of stainless steel size 17 x20 x 4 of grade SS-304 complete all as specified & directed.Make : Godrej, Hettich, KAFF 38 S & Fkitchen prerforated cutlery baskets ofstainless steel size 17 x20 x 4 of grade SS-304 complete all as specified & directed.Make : Godrej, Hettich, KAFF 39 S & Fkitchen cup & saucer baskets of stainless steel size 17 x20 x 4of grade SS-304complete all as specified & directed.Make : Godrej, Hettich, KAFF 40 S & Fkitchen plate baskets of stainless steel size 17 x20 x 6 of grade SS-304 complete all as specified & directed.Make : Godrej, Hettich, KAFF 41 S & Fkitchen grain baskets of stainless steel size 17 x20 x10 of grade SS-304 complete all as specified & directed.Make : Godrej, Hettich, KAFF 42 S & F stainless steel basket guide channels suitable for running basket as mentioned in items above of grade SS-304 complete all as specified & directed.Make : Godrej, Hindware, Lifetime, Hettich 43 S & F auto close hinges, stainless steel of grade SS-304, bright finish fixed complete all as specified.Make : Godrej, Hindware, Lifetime or equivalent 44 S & F stainless steel handles of size 100 mm fancy type of approved make complete all as specified & directed.Make : Godrej, Hindware, Lifetime or equivalent 45 S&F in repair sinks made of stainless steel 18 guage of grade SS-304, kitchen or labortory with plugs, washers and wastes pipe and coupling including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to ipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. 46 Taking up or down 15mm steel tubing and connections including cleaning and refixing old steel tubing and connections in new or old positions (walls, ceiling and floor etc) incl new fittings complete all as specified and directed. 47 Taking up or down 20mm steel tubing and connections including cleaning and refixing old steel tubing and connections in new or old positions (walls, ceiling and floor etc)incl new fittings complete all as specified and directed. 48 S&F in repair 15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or laid in floor including taking down old complete all as specified and directed. 49 S&F in repair 20 mm dia steel water tubing, galvanized, medium grade, with all fittings,fixed to walls and ceiling or laid in floor including taking down old complete all as specified and directed. 50 S&F in repairs 15 mm bore bib tap, fancy type, chromium plated cast copper alloy with cruth or butter fly handle, long body, screwed down, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. 51 Supply only pillar taps 15mm bore swan neck cast coper alloy CPfancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union complete all as specified and directed. 52 S&F in repair brass CP towel rail 20mm dia, D type 60 cm long between flanges complete all as specified and directed. 53 S&F in repair double soap dish, CP brass R typefixed to plugs with chromium plated brass screws complete all as specified and directed.. 54 S&F in repair brass chromium plated shower rose 125mm x 125 mmsize with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed. 55 S&F in repair 15mm bore stop/angle valves, cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed for iron pipes or for unions and fixed complete all as specified and directed. 56 S&F in repair PVC Connections 15mm size, 450mm long with PTMT nuts complete all as specified and as directed. 57 S&F in repair 20mm bore gun metal gate valve, screwed down high pressure with iron wheel head screwed both ends for iron pipe or for union complete all as specified and directed. 58 S & F in repair 15mm bore wall mixer, brass, chromium plated, fancy type, 3-in-1 for mixing hot & cold water, with L-bend pipe for connection to overhead shower, bright finish with three joints screwed the ends for iron pipeand plugging complete all as specified and directed. 59 S & F in repair 250 mm corner glass shelf with brass brackets incl chromium plated brass screws complete all as specified & directed. 60 S & F in repair vitreous china squatting pan, Orissa pattern, size 580 mm X 440 mm white with ‘P’ or ‘S trap, front or back inlet and integral foot rests, any pattern and including fixing bolt, connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed. 61 S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), including plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device and connection to drain (or out going pipe) and to flushing pipe etc. incl trap set in cement concrete complete all as specified and directed. 62 S&F in repairs PVC valveless, syphonic action type flushing cistern, low level, 10 ltr capacity, white, with intel, ball valve, float and handle including brakects, 32 mm dia polyethylene of low or high density or PVC flushing pipe and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified & as directed. 63 S&F as in repair 15 mm bore two way bib tap, cast copper alloy chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. 64 S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed. 65 S&F in repairs vitreous china wash hand basin white flat back of size 550 x 400 mm excluding taps, waste pipe, chain & plug and porcelene stopper but including brackets /fastners, 32mm dia brass chromium plated waste coupling with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, cutting for and pinning in ends of brackets, including fixing of pillar tap complete all as specified and directed. 66 S& F 32 mm bore PVC waste pipe 75 cm long of approved make with 32mm dia connector suitable for WHB/sink complete all as specified and directed. 67 Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed. 68 M&L for brick work with sub-class B bricks (old size), straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed 69 M&L for brickwork with subclass ‘B’ bricks (old size), straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6 complete all as specified and directed. 70 M&L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed. 71 Dismantling of 100mm bore cast iron soil/ waste pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or fromtrenches, if required complete all as specified and directed. Note : The length shall be measured along the centre line including fittings and accessories). 72 Dismantling of 75mm bore cast iron soil / waste pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or fromtrenches, if required complete all as specified and directed. Note : The length shall be measured along the centre line including fittings and accessories). 73 S&F 110 mm UPVC(SWR) ventilation and rain water pipes (type A conforming to IS-13592) single socketed, in any length with rubber ring joints fixed to wallls with suitable size clamp complete all as specified & directed. 74 S&F 110 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints fixed to wallls with suitable size clamp complete all as specified & directed. 75 S&F 110 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints laid in trenches or floors complete all as specified & directed. 76 S&F 75 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints laid in trenches or floors complete all as specified & directed. 77 S&F 75 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints fixed to wallls with suitable size clamp complete all as specified & directed. 78 S&F 110 mm dia UPVC (SWR) junction single (Single Tee with access door) equal or unequal complete all as specified and directed. 79 S&F 110 mm dia UPVC (SWR) bends any radius with access door complete all as specified and directed. 80 S&F 75mm dia UPVC (SWR) junction single (Single Tee with access door)equal or unequal complete all as specified and directed. 81 S&F 75mm dia UPVC (SWR)bends any radius complete all as specified and directed. 82 S&F 75 mm UPVC (SWR) vent cowl complete all as specified and directed. 83 S&F 110 mm UPVC (SWR) vent cowl complete all as specified and directed. 84 S&F in repair PVC (SWR) 75 mm dia of outlet nahani trap/floor trap with grating including jointing with solvent cement complete all as specified and directed. 85 S& F in repair PVC (SWR) gully traps of size 125/110 setting and jointing with solvent cement complete all as specified and directed. 86 S & F in repair MS CP Grating doom 100 mm dia with or without waste hole complete all as specified and directed. 87 S & F in repair 500 Ltrs capacity rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc incl 20mm dia ball valve high pressure of PTMT with polythene flynut and aluminium rodincl dismantling of old tank all as specified in SSR Part I complete all as specified and directed by Engineer-in-Charge. 88 Taking down shutters of any description exceeding 1 sqm and n.exc 2 sqm each and refixing after easying in the same opening complete as directed and specified. 89 Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed. 90 Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed. 91 Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed. 92 S&F 100x75mm, rebated, karoli stone chowkats with exposed faces close picked dressed, including 4 bolt holes `per upright, erected in position and bedded and pointed in lime mortar 1:3 or cement mortar 1:6 complete all as specified & directed. 93 S&F 125x75mm, rebated, karoli stone chowkats with exposed faces close picked dressed, including 4 bolt holes `per upright, erected in position and bedded and pointed in lime mortar 1:3 or cement mortar 1:6 complete all as specified & directed. 94 S & F for Solid wood grain printed PVC sheetdoor frame of size 50mm x 95mm made by joining 3nos. Heat bent PVC Sheet `C Channel of 5mm thickness of sizes 35mm x 30mm x 25mm & 40mm x 35mm x40mm & 25mm x 30mm x 35mm using solvent cement. The two side `C Channel shall be reinforced with M.S. tube of size 19mm x 19mm. All the three `C channel Shall be fixed to flat base of 5mm PVC sheet with solvent cement. The profile shall be mitre cut at two corners and joined by inserting 4nos. 150mm long brackets of 15x15mm M.S. Square tube inside the 19mm x 19mm square tubes & remain each of then with four screws as indicated in the drawing. 95 S&F for 35 mm thick Factory made solid EPS core PVC Moulded Door shutter, 28 to 30 mm thick (stiles), with 2, 4 or 6 raised panel design, consisting of frame made out ofMS tube 20 mm x 40 mm. The core panel shall consist of 25 mm thick high density EPS routed with design, sandwitched in between front side moulded prelam 2 mm thick Moulded PVC sheet on one face and 2 mm PVC sheet on other side. The shutter on all edges to be sealed with lipping of 10 mm (5mm x 2) thick x 25 mm wide PVC sheet on other side & 60 mmwide PVC sheet for lock lock rail side . the lipping shall be bonded to the 2 mm moulded / plain PVC sheet with solvant cement asas specified and shown in SSRand Particular specification & as directed. Note :- .(i) The PVC doors shall be fixed as per manufacturers instructionsand as directed 96 S & F 35mm thick flush shutters solid core construction with block board and plywood face panels,fixedwith approved adhessive incl lipping all round the edges of door as per manufacturers instructionscomplete all as specified and directed. 97 M&L for decorative laminate type-I, 0.9 mm thick, colour and pattern as approved fixed as in door shutters complete all as specified and directed. 98 S & F 35mm thick second class hardwood factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc divided into square , with plain, chamfered or rounded, mitred and rebated sash barsany numbers ,fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. Note :-Glass/gauge shall be measured and paid for separately 99 S & F 35mm thick factory made partly gauzed and partly panelled skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. Note :- Supply of glass/gauge shall be measured and paid for separately 100 S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples in window or door complete all as specified and as directed. 101 S &F Framed work such as door frame, grills, gratings, etc., with ends of bar shoulder &/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks with Angle, MS sheet Flat iron & similar work conforming to Fe 290 GDE -E-165complete all as specified and directed. 102 S & F SS(SS-304) butt hinges 150 mm size heavy weight and fixed complete fixed in stone choukats all as specified and directed. 103 S & F MS butt hinges 100mm size cold rolled medium weight and fixed complete all as specified and directed. 104 S & F 250 mm long SS sliding door bolt with hasp, staple (bolt type) not less than 12 mm dia with & minimum of 6 bolts & nuts , 4 on bolt plate & 2 on staple plate complete all as specified and directed. 105 S & F 150mm size SS (grade-304) handles, cast moulded type fixed with screws complete all as specified and directed. 106 S & F SS (grade-304) barrel tower bolts not less than 12 mm dia of extruded section, 200mm long complete all as specified and directed. 107 S & F 75 mm long door stopper of stainless steel body with two number rubber shoes complete all as specified and directed. 108 S & F MS Helical door spring 150mm long including roller and roller plate complete fixed to angle iron chowkats as directed and specified. 109 S & F in repair pressed steel factory made cupboard shutter with frame of 1.25 mm thick and shutter 1 mm thick PBI sheet with 6 nos 3.15 mm thick and 100 mm long steel hinges, godrej patern locking arrangement incl 12 mm dia vertical rod incl spray painting in factory in wood finish pattern complete all as specified and directed 110 S&F in repair 25 mm dia SS (grade 304) drapery/curtain rod medium weight incl taking down old one with finials, brackets etc complete all as specified and directed 111 S&F SS (grade-304)brackets/ end brackets for holding 25mm dia drapery rod complete all as specified and as directed. 112 S&F SS (grade-304) Finials, fancy type of approved make and pattern suitable for 25mm drapery rod complete all as specified and directed. 113 M&L for prearation of new or previously untreated steel and iron surface of any description, over 10cm in width and girth not otherwise described and applying two coat of synthetic enamel paint over one coat of red oxide (zinc chrome) primer complete all as specified and directed. 114 M&L for preparation of new wooden or wood based surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 115 M&L for preparation of old painted wooden or wood based surfaces of any description not otherwise described over 10 cm in width or girth and applying two coat of synthetic enamel paint complete all as specified and directed. 116 M&L providing cement concrete type B-1, 1:2:4 (using 20 mm graded aggregate) in lintels up to 1.5m clear span, cills, bed plates,coping, kerbs water trough & the like including weathering, slightly rounded or chamfered angles & throating complete as specified and directed 117 Demolition existing water proofing treatment includingPCC in roof covering/padding kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type upto mother slab of roof complete as specified and directed.incl removal all rubbish material outside of MoD Land 118 M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying average 40mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded stone aggregate)finished even & fair to cover negative slope complete as specified and directed 119 M&L screed plaster 10mm thick in cement mortar (1:4) on concrete surfaces of roof to receive water proofing treatment and finished the surface even and fair incl mixing of WPC as per manufacturers instruction complete all as specified and directed.Note:- water proofing compound paid seperately as supply only 120 Supply only integral water proofing compund ISI marked complete all as specified and directed. 121 Supply and laying water-based, single component UV resistant, elastomeric PU liquid water proofing coating, having SRI >109 with an elongation of >400% and tensile strength of 1.4 MPa as per ASTM D 412, 80 % Solid Content, shore A Hardness of min. 50 as per ASTM D 2240 using roller in four layer (Primer coat,First coat, Fibre reinforce mesh & final coat) providing 1.2 mm DFT as per manufacturers specifications and instruction complete all as specified and directed. Application:- (a) Surface to be treated shall be free from loose particle etc then apply first coat of liquid water proofing as a primer on the surface with diluting as per manufacture instruction and allow the surface to dry for min 10-12 Hr time period. (b) Apply Second coat of Liquid water proofing without dilution on the primed surface and allow time to dry the surface for min 10-12 hr. (c) Apply Fibre reinforce mesh as per manufacturers instruction (iii) Applying third coat of liquid water proofing without dilution over the fibre rei coat and Allow minimum 48 hours before subjecting the painted surface to service.Note : (i) Work shall be carried out through authorized applicator of manufacturers only(ii) Material shall be used as per technical data / instruction of manufacturer after written approval of garrison engineer before execution at site and contractor shall submit guarantee of roof treatment work for TEN years Make:- Asian Paint : PU Aqua, M/s STP LTD-Shaliurethane BTD, Berger : Elastoseal BTD, Fosroc : Nito proof as approved by GE 122 M & L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length.Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed. 123 M&L for PCC 1:3:6, type C2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed. 124 S&F in repair 600 x 450mm bevelled edge mirror 5.5mm to 6mm thick selected quality glass flaw less,firmly mounted on 6mm thick commercial ply wood backing and fixed to wooden plug with chromium plated brass screw and cup washer complete all as specified and directed. 125 S & F in repair stainless steel kitchen plate rack of approved quality of overall minimum size 750 x 600 x 250mm with partitions for small/ large plates etc made out of stainless steel 24 gauge, fixed with rawl plug and CP steel screws complete all as specified and directed. 126 M&L Mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape requried, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 127 ,---ditto--- all as per item No. 126 above but TMT bar 10 mm dia & over complete all as specified and directed . 128 M & L for providing precast cement concrete type B1 1:2:4 (using 20mm graded aggregate) in landing, cover slab (for man hole etc) chullah hood, chajjas, water troughs, mangers, shelves and similar articles with plain faces incl form work set in cement mortar 1:6 complete all as specified and directed. 129 Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description andin any positionnot otherwisespecifically provided for complete all as specified and directed. 130 M&L form work to chullah hoods, chajjas, troughs and similar items including edges finish with rough finish surface complete all as specified and directed. 131 M&L for RCC (nominal mix) 1:1.5:3 Type A1(using 20 mm graded stone aggregate ) as in Chhaja, roof projections etc.complete all as specified & directed.Note :- Reinforcement shall be measured and paid for separately. 132 Dismantling plain or corrugated steel / FRP sheeting any gauge, thickness complete all as specified and directed. 133 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. 134 S & F steel work in tubular trusses incl special shaped washer etc, complete using ERW or induction butt welded tubes conforiming to IS 1161-1979 graded St-240 complete all as specified and as directed. 135 S&F Mild Steel work in roof trusses (framed), trussed, purlins, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde E-250) qulaity A including fabrication, erraction and fixing complete all as specified and directed. 136 S&F pre painted galvalume aluminium zink coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and washers complete all as specified and directed. 137 M&L for 100 mm thick cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base complete all as specified and as directed. 138 M & L rubber moulded machine pressed precast concrete interlocking paver block, coloured, any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, with coloured cement and pigment laid over and incl 25mm thick sand cushion layer complete all as specified and as directed.Note : Sand for cushioning shall be included under quoted rates. 139 M&L for precast cement concrete 1:3:6, type C1 (using 20mm graded stone aggregate) solid blocks, exc 10 cm in width as in kerb stones and setting in cement mortar 1:4 incl necessary earthwork complete all as specified and as directed. 140 M&L for powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators, Partition section with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 141 S&F Powder coated anodised aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge 142 S&F Galvanised mild steel cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples in window or door complete all as specified and as directed. 143 S &F 4.8mm thick tinted glass ordinary quality and fixed in aluminium beads in sqaures not exc 0.5 sqm in each pane complete all as specified and directed. 144 S&F powder coated (thickness not less than 50 micron) aluminum grill 6-8 mm thick of approved design aperture size 50mmx50mm of standard sections including F type aluminium snap beading screw complete fitted to aluminium frame section complete all as specified and directed. 145 Excavation in trenches not exc 1.5m wide and n exc 1.5m in depth, for foundation, etc or for shaft , wells, cesspits, manholes, pier holes, etc n. exc 10 Sqm on plan and not exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed. 146 ,---ditto--- all as per item No. 145 above but depth exc 1.5m but not exc 3m complete all as specified and directed. 147 Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm in soft/ loose soil complete all as specified and directed. 148 Removing excavated material n.exc 50m & depositing where directed at a level n.exc 1.50m above the starting point in soil complete all as specified and directed. 149 Demolition and breaking up drain pipes (Salt glazed ware, AC or reinforced concrete) 150mm dia set in cement mortar complete all as specified and directed. 150 Supply & laying DWC pipe (Double wall corrugated ) of class SN-4, IS-16098 (Part –II) of size internal dia of 150 mm, laid in trenches and jointed complete with coupler, bend, Tee, reducer etc complete all as specified & directed .Note :Earth work shall be measured and paid seperately 151 Taking down carefully surface aluminum /copperpoint wiring, casing capping /PVC concealed conduit for (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified and directed. 152 Taking down MCB distribution board with incoming and outgoing controls any make and capacity after disconnecting complete all as specified and directed. 153 Taking down light fittings of any type any make any capacity complete all as specified and directed. 154 Taking down carefully sub main wiring with PVC casing capping / PVC surface conduit and making good disturbed surfaces complete all as specified and directed. 155 M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable, single core, 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one light /fan point controlled by one, one way switch 6 Amp complete all as specified and directed. 156 ,---ditto--- all as per item No. 155 above but for one bell point controlled by one bell push complete all as specified and directed. 157 ,---ditto--- all as per item No. 155 above but for one light point controlled by two, two way switch complete all as specified and directed. 158 ,---ditto--- all as per item No. 155 above but for one 3 pin 5 Amp socket outlet controlled by one switch on same board complete all as specified and directed. 159 ,---ditto--- all as per item No. 155 above but for one 3 pin 5 Amp socket outlet controlled by one switch on indepdendent board complete all as specified and directed. 160 M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable single core, 4 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one 3 pin, 15amp socket outlet on independent board complete all as specified and directed. 161 S&F modular switch,6 Amps, one way, 240 volts, 1 module complete all as specified and directed. 162 S&F modular switch, 6 Amp, two way, 1 module AC 240 volts complete all as specified and directed. 163 S&F modular switch 16 Amps, one way, 240 volts, 1 module complete all as specified and directed. 164 S&F modular bell push, 6 Amp, 1 module complete all as specified and directed. 165 S&F modular socket, 6 Amps, 2/3 pin combined, 2 module AC 240 volts complete all as specified and directed. 166 S&F modular socket, 6/16 Amps, 2/3pin combined, 2 module AC 240 volts complete all as specified and directed. 167 S&F modular hum free electronic step fan regulator 120-280 volts of 120 watts capacity (socket type) including connecting up complete all as specified and directed. 168 S&F ceiling rose PVC polycarbonate isolated body, 3 terminals 230 Volt complete all as specified and directed. 169 S&F ceiling fan 1200mm sweep 50 Hz AC 230 votls, 5 star rated in white colour with BLDC fan motor, Min air delivery 210 CFM with service value 6.00 BEE, incl blade set, 0.45 mtr down rod, canopy set, rubber reel including 0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling and writing MES No. on fan body as required complete all as specified and directed. 170 M&L for sub main wiring with four run of 10 Sqmm single core, PVC insulated, unsheathed, FRLSH multistranded copper conductor cable alongwith one run of 10 Sqmm earth wire as earth continuity conductor (Phase-Red, Neutral-Black, Earth-Green) drawing into and including concealed rigid non-metallic PVC conduit of 20mm dia, ISI marked, ivory colour with fitting / fixing accessories of suitable size as required including making connection as required complete all as specified and directed. NOTE - Four run of 10 sq.mm phase and neutral wire, One run of 10 sq.mm earth wire & One run of PVC conduit with accessories shall be measured as One length. 171 M&L for sub main wiring with two run of 6 Sqmm single core, PVC insulated, unsheathed, FRLSH multistranded copper conductor cable alongwith one run of 6 Sqmm earth wire as earth continuity conductor (Phase-Red, Neutral-Black, Earth-Green) drawing into and including concealed rigid non-metallic PVC conduit of 20mm dia, ISI marked, ivory colour with fitting / fixing accessories of suitable size as required including making connection as required complete all as specified and directed. NOTE - Two run of 6 sq.mm phase and neutral wire, One run of 6 sq.mm earth wire & One run of PVC conduit with accessories shall be measured as One length. 172 S&F MCBs Distribution board SPN, 8 ways, powder coated CRCA steel sheet, degree of protection IP-43, IK-09 with reversible double door, 240V, recess mounted having insulated 200 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs incl taking down old U/S DB complete all as specified and directed.Note : MCBs and MCB DB shall be of the same make. 173 S&F MCBs of B curve, single pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked, 240Voltsincluding required wiring connections with copper lugs of suitable size provided in MCB DBs incl connection testing and commissioning complete all as specified and directed. 174 S&F MCBs of B curve, Double pole 10 to 32 Amps having breaking capacity 10 KA, ISI marked, 240Voltsincluding required wiring connections with copper lugs of suitable size provided in MCB DBs incl connection testing and commissioning complete all as specified and directed. 175 S&F LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficiency of 105 lumen per watt and total power consumption not more than 20 watt including driver.It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed.Make - Philips Cat part BN308C LED20S-6500 L120 PSU WH, Crompton Cat part CIS-305-40-57-SL-DP-NWH, Havells Cat no STOUTPLUS600BS20WLED840SPCWH. 176 S&F LED batten (0.6m) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 900 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 10 watt including driver.It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed. 177 S&F LED bulk head light fitting 9 watt IP 66 & IK 09 with with pressure die cast aluminium housing & polycarbonate diffuser duly prewired connection with 0.75sqmm PVC insulated & sheathed three core flexible multi stranded copper conductor cable complete all as specified & directed. 178 M & L Sand cushioning to under ground cable with screened and washed sand (non cohessive), 8 cm before laying cable and 15cm after laying and punned to 18cm after laying of cable complete all as specified and directed by Engineer-in-Charge.Note : Punned thickness shall be considered for payment purpose. 179 M&L for factory made unreinforced pre-cast concrete cable protection cover LV class type-I with size 250mm X 150mm X 40mm laid across the cable (i.e. width of cover along the length of cable) for UG cable protection on the top of the sand cushioning complete all as specified and directed. 180 S & F in repair 50 mm bore GI tubing light grade with all fittings, fixed to wall/ pole with suitable size MS clamp, nut, bolt, washer etc or laid under road crossing etc as reqd for protection of cable incl painting with two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed.Note : Cost of MS clamp, nut bolt, washer and GI fittings etc shall be inclusive in the quoted rates. 181 Dismantling and taking out UG cable any size and fixed in any position and removal from site complete all as specified and directed. 182 Supply, laying, jointing, testing & commissioning LT under ground cable XLPE insulated, screened PVC sheathed, galvanised steel strips or wire armoured, heavy duty electric cable with multi stranded aluminium conductor, 1100 volts grade cross sectional area 16sqmm, 2core confirming to IS:7098 (part-I), laid in trenches, ducts, pipes or fixed on poles or walls including all necessary clamps, nut, bolt, washers, saddle etc complete all as specfied and directed.Note : The cost of AI thimbles / lugs and cable gland etc is included in quoted raes. 183 M&L for earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6.0mm buried directly in ground, vertically to depth not less than 2.25mtr below normal ground level with top edge of the earth plate at depth not less than 1.5 metre below ground level surrounded from all sides with alternate layers of charcoal and common salt and connected to GI lead wire 4.0mm dia by means of GI bolts, nuts washers & check nuts electrode connected to main switch board or main control board or on poles or on transformer and GI pipe medium grade 20mm bore for watering, 40mm bore GI pipe medium grade for protection of GI wire upto test point including providing funnel and wire mesh GI frame and 10cm thick suitably reinforced RCC pit cover, PCC chamber pit with PCC (1:3:6) type C2 using 40mm graded stone aggregates complete including excavation and earth work in any type of strata, disposal of surplus soil to a distance not exceeding 50 mtr, all as specified ans shown in Electrical plate No. 3 of SSR Part-1, PCC pit shall be provided at least 50 cm away from the earth pit and not just on earth pit including testing on completion complete.(Note - GI lead wire size 4.0mm upto 7.5 m included in the item). 184 S&F in replacement fresh air fan of sweep 200 mm, made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, 1200 RPM, copper winding incl making connections complete all as specified and directed. Note : Old U/S plastic fresh air fan shall be deposited to MES store yard 185 Taking down carefully exhaust fan 300mm sweep, metal body with louvers, fan motor and accessories complete and including minor repair and refixing the same after repairing at new or old location complete all as specified and directed. 186 Taking down carefully storage type water heater (geyser) 25 ltr capacity, any make, from clamp/bolts including disconnecting water and electric connection and re fixing the same and connecting up after cleaning of geyser and minor repair and replacement of damaged PVC connection, plug top etc complete all as specified and directed. 187 S & F in repair 20amp, single pole and neutral socket outlet, with 2 pole and earth, metal enclosed plug top in powder coated CRCA steel sheet enclosure recess mounted with chained matel cover for socket out let with and incl one single pole B curve MCB 20 Amps complete all as specified and directed. 188 M&L for clamp and back plates fabricated from steel sections conforming to Gde Fe 410-O or Fe 310-O including nuts, bolts, washer, drilling holes for bolts in any shape or size for fixing ceiling fan complete all as specified and directed. 189 M&L for taking out ceiling fan 1200/1400mm sweep 50Hz AC 230 volts, dismantling fan blade and refixing the same including minor repair and replacement of fan blade, down rod, nut, bolt and washer including 0.5sqmm thre core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling as required and writing MES No. on fan body complete all as specified and directed.Note :Material reqd for repairing shall be paid seperately as supply only 190 M&L for rewinding the motor of ceiling fan 1200/1400 mm of any type and make with super enamelled copper wire of existing gauge of approved quality including overhauling and minor repairs for satisfactory operation, testing for the original speed & consumption complete all as specified and directed. 191 Supply only ball bearing no- 6201 to 6204 for ceiling / exhaust fan etc. of any size and make as required with alignment of shaft and testing complete all as specified and directed. 192 Supply only AC film capacitor 2.5 mfd, 440 volts suitable for any type ceiling fan in FR plastic casing including connection complete all as specified and directed. 193 Supply only shaft of approved quality for ceiling fan / exhaust fan any make any type & size as required complete all as specified and directed. 194 M&L for painting of ceiling fan of any sweep and make with one or more coats of spray painting with best quality enamel paint of required colour and approved brand to give an even shade and polishing with rubbing compound and wax polish including cleaning of surface with detergent etc complete all as specified and directed. 195 Supply only rubber reel with a pair of clamp, nuts, bolts, split pins etc suitable for ceiling fan down rods of any size and make as required complete all as specified and directed. 196 Supply only PVC canopy suitable for ceiling fan of any size and make as required complete all as specified and directed. 197 Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule A/BOQ
