Tender For special Repair To Bldg No Np-2 (Single Offr Accn) Of Asc Bn And Provn Of Storage Accn At Ge Satwari Under Ge Satwari--- 1 Taking down shutter exc 1.0 sqm and n. exc 2.0 sqm each and removing from site complete all as specified and directed. 2 Taking down chowkats or frames with shutter (without taking off shutter from the frame) n. exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed. 3 Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 sqm & n. exc 4 sqm each includingcutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed. 4 Demolition of cement concrete (un-reinforced) ground floor to 4th floors and pavings n exc 15 cm thickness (below or above ground level ) and removingthe rubbish from the work site to out side defence premises complete all as specified and directed 5 Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided and including removing from site to a distance n exc 500 mtrs , complete all as specified and as directed. 6 Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubing down with water etc and removing unserviceable material outside defence land complete all as specified and directed. 7 Dismantling floor, hearth or wall tiling/ terrazzo dado from wall surface including cement mortar bedding, (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specied and directed. 8 S&F pressed steel frames of size 105mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including mild steel hinges, 100 mm long , medium weright and 25 mm x 3 mm flat iron as in hold fast , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed. 9 S&F pressed steel frames of size 125mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including mild steel hinges, 100 mm long , medium weright and 25 mm x 3 mm flat iron as in hold fast , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed. 10 S&F 35 mm thick 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framingplain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkats complete all as specified and directed 11 M&L for 30mm thick flush shutters, solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed. 12 S&F SolidPVC door frame of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. square tube, egdes will be painted to match printed sheets completeall as specified and directed .. 13 S&F Factory Made Solid PVC Moulded Door Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specified and directed 14 S&F 100mm long stainless steel butt hinges, fixedwith screws complete all as specified and directed 15 S&F aluminium anodised barrel tower bolts, 150mm long of extruded section, fixed to doors with screws complete all as specified and directed. 16 S&F aluminium anodised ,cast type handle 100mm size complete all as spcified and directed. 17 S&F aluminum alloy, anodised, sliding door bolt of length 250mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminum alloy and fixed complete all as specified and directed. 18 S&F140 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. 19 S&F300 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate including fixing to pressed steel frames with necessary welding work complete all as speciied and directed 20 Taking down old/unserviceable kitchen cabinet/cupboard including allfixtures and fittings complete all as specified and directed. 21 S&F factory made 18 mm thick (+0.7mm) celuka PVC ply of density 600 kg/cbm . One side prelam and other side plain 18mm thick celuka PVC ply for kitchen cabinet shutter/shelf/ partition/drawercomplete as per manufactuers specifications and drawing and as directed . 22 S&F factory made 5 mm thick PVC plain sheet of density 600 Kg/cbm . as in paneling for back side (wall side) for kitchen cabinet shutter/shelf/ partition/drawer complete as per manufactuers specifications and drawing and as directed . 23 S&F 125mm long stainless steel handle complete all as specified and directed. 24 S&F Rolling channel plate for kitchen cupboards complete all as specified anddirected. 25 S&F steel fasteners of size 75 mm long, drilled and fixed to walls complete all as specified and directed. 26 S&F Pressed steel cup board framemade out of MS sheet 1.25 mm thick, of size 60x40mm with rebate of 20 mm wide and 12 mm deep includingstainless steel butt hinges 100 mm long and PCC 1:2:4 B-1 as in back fill to chowkats complete all as specified and directed. . 27 S&F Prelaminated MDF board 19 mm thick ,exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination,as in shutters/shelves fixed with screws to timber frame work including lipping (15 mm thick three sides and 20 mm thick lipping hinge side) around the shutter complete all asspecified and as directed . 28 S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20gauge with stainless steel brackets near toends with stainless steelfinialsat both ends and necessary fittings complete all as specified and directed. 29 S&F steel window/ventilator 1.25 mm thick Box type (Double Shutter) ERW hollow P section of size 60 mm x 25 mm single rebated comprises glazed & wire gauged skelton shutter ERW sec 50 mm x 20 mm and 1 mm thick with two Nos sash bar of T- section 20 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window including following fitting welded to frame shutter hold fast of 150 mm long of 12 mm x 3 mm FI made to shape 4 No, handle of Z section 20 mm x 25 mm x 100 mm long 1 No per leaf, MS tower bolt 150 mm long 2 No per leaf, Z sec 20 mm x 25 mm, 100 mm long stopper 1 No on per leaf, MS pintal hinges of size 75 mm x 12 mm 2 No per leaf fabrication, as per drg No CEPZ/TD-324,325 complete all as specified and directed. 30 M&L for framed work such as grills , gratings etc with ends of bars shouldered and /or riveted or forged into spikes , framed guard bars, barred iron doors, ladders, framed balusters: walk ways , railings frame work of water tanks and similar work confirmingto Fe290, Gde E-165 complete all as specifiedand directed 31 M&L for 3 mm thick, plain sheet glass, ordinary quality and glazing with oil putty or with any type of beadsin squares n. exc 0.5 sqm each pane complete all as specifiedand directed. 32 S&F 3 mm thick , figured glass, pin head type and glazing with oil putty or with any type of beads in squares n. exc 0.5 sqm each pane complete all as specified and directed. 33 S&F galvanised mild steel wire cloth , 0.56 mm normal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed. 34 S&F in repair angle valve with flange,cast copper alloy,fancy type,chromium plated, screwed down for high pressure , screwed both ends for iron pipe of 15mm bore complete all as specified and dircted. 35 S&F in repair bib taps,long body, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle , screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed. 36 S&F in repair PTMT cabinet with mirror of selected glass of size 330x430mm, fixed with screw complete all as specified & directed 37 M&L for 16 to 18mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite & moulding the edges,making hole for gas pipe over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified anddirected. 38 M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.. 39 M&L for reinforced cement concrete M-25, Design mix, (using 20mm graded crushed stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconiescomplete all as specified and directed. 40 M&L for mildsteel TMTbars 10mm dia and over, cutto length, bent to shape required, including cranking, bendingspirallyforhooping forcolumn, hookingendandbinding withandincludingmildsteelwire(annealed) not lessthan0.9 mm dia orsecuring with clips, complete all as specifiedand directed . 41 M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups , spacers and binders including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. 42 M&L for use and waste of form work to softfits of suspended slabs such as roof slabs , floor slabs , landings and similar work, not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete complete all as specified and directed. 43 M&L for use and wasteof formwork to edges of concrete flats, treads, breaks in floors,window cills,concrete railings, openings in concrete walls, floor and roofs, n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n. exc 15cm widefair finished surface complete all as specified and directed . 44 M&L for plain cement concrete 1:2:4 ,type B1(using 20mm graded crushed stone aggregates) as in lintels upto 1.5m clear span, window or door cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings,side posts of precast jallies etc. including slightly rounded or chamfered angles including necessary formwork complete all as specified and directed. 45 S&F in repair vitreous china wash down water closet pan (pedestal pattern) of size 520x360x390mm white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes, connecting only to flushing cistern, anti-syphonage pipe with PVC flush pipe of 32mm dia including plastic seat with cover, white in colour with mild steel chromium plated hinging and P or S trap device complete all as specified and directed 46 S&Fin repair PVC connection 15 mm x 600 mm including PVC check nut at both ends complete all as specified and direced. 47 S&F in repair 10 litres PVC, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float 32mm PVC L bend and handle including brackets complete all as specified and directed 48 S&F in repair central hole basin mixer without popup waste system with 450mm long braided hoses, screwed down for 15mm bore iron pipe complete all as specified and directed. 49 S&F in repair wall mixer 3-in-1 system with provision of overhead & hand shower complete with 115mm long bend pipe, connecting legs & wall flange fancy type complete all as specified and directed. 50 S&F in repairbrass chromimium plated sink mixer swan neck with swinging spout (wall mounted model) with connecting Legs & wall flanges complete all as specified and directed. 51 S&F in repair 2 in 1 angle valve with flange,cast copper alloy,fancy type, chromium plated, screwed down for high pressure , screwed both ends for iron pipe of 15mm bore complete all as specified and dircted. 52 S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connectios and fixed in position complete all as specified and directed. 53 S&F in repair door closer hydraulically regulated, Aluminium (extruded section body), designation No 3, universal type suitable for door shutter 851mm to 1000mm width and weight between 61 to 80 kg complete all as specified and directed. 54 S&F aluminium powder coated (coating not less than 50 micron) door frame and door shutter,door frame of hollow section 101mm x 44.0mm x thickness not less than 1.53 mm & hollow section of stiles of glazed shutter 85mm x 44.45mm x thickness not less than 1.56mm having grooves for aluminium beading and top rail of hollow section 83.5mm x 44.45mm x thickness not less than 1.50mm, lock rail of hollow section 83.5mm x 44.45mm x thickness not less than 1.50mm and bottom rail of hollow section 83.5mm x 44.45mmx thickness not less than 1.50mm ,one derived handle 300mm long,100mm long butt hinges - 4 Nos , aluminium mortice lock 65mm 4 levers of Godrej patternandrubber packing, aluminium beadingcomplete all as specified anddirected. 55 M&L for aluminum powder coated (coating not less than 50 micron), sliding window, three track with stainless steel mosquito proofingwith window style of section 44.4mmx44.5mmx 2.0mm thick and frame of section 101.60 x 44.45 mmx 1.20mm thicknessincluding 4.0 mm thick coloured/tinted/frosted glass panes & stainless steel wire mesh of aperature 0.63mm and all necessary fittings and fixtures complete all as specified and directed. 56 S&F Powder coated aluminum (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators,frame work & partitions including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately ) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS :1285, fixing with dash fasteners of required dia and size, including neccessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as specified and the directed .. 57 S&F aluminium powder coated (coating not less than 50 micron) door frameof hollow section 101.60mm x 44.45mm x thickness not less than 1.20 mmfixed with floor, ceiling, walls and cills where required and fixing with the help of rawl plug and screw or with fixing clip or with expansion hold plate fastenerscomplete all as specified and directed. 58 S&F aluminium anodized powder coated (powder coating not less than 50 micron) grills 6 mm dia of size 100x100mm fixed to aluminium windows complete all as specified and directed. 59 M&L for 5.5 mm thick, tinted sheet glass ordinary quality and glazing with oil putty or with any type of beads (supplied alongwith shutters) in squares exc 0.5 Sqm in each pane complete all as specified and directed. 60 S&F 4mm thick aluminium composite panel (coloured sheet)including necessary accessories for fitting complete all as specified and directed 61 S&F in repair vitreous china counter wash basins, size 560x470x190mm, oval shape,white to be fixed on counter/ RCC slabincluding CP waste coupling & PVC waste pipe complete all as specified & directed. 62 S&F in repair brass chromium plated tubular towel rail 20mm dia, D type , 600 mm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed. 63 S&F in repair Chromium plated tubular towel ring of 150mm dia, fixed to plugs with chromium plated brass screw including wooden/plastic beads complete all as specified and directed. 64 S&F in repair rust resistance stainless steel peg set of six complete all as specified and directed. 65 S&F in repair stainless steel square foldable towel rack,600mm size complete all as specified and directed. 66 S&F in repair sheet glass shelf assembly consisiting of 5.5 mm thick sheet glass, shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. 67 S&Fin repair corner glass shelf of size 30cm with chromium plated bracket guard and railing fixed with and including screws and wooden/plastic cleats complete all as specified and directed . 68 S&F in repair bevelled edge mirror of 5mm thick selected quality glass, mountedto wall and fixed with wooden/PVC rawl plugs with stainless steel screws & cup washerscomplete all as specified anddirected. 69 S&F in repair brass chromium plated shower rose 125 mm of size with arm and with or without swivel joints to steel pipe or union complete all as specified and as directed. 70 M&L for dismantling of water tank of capacity exc 500 ltrs but n. exc 1000 ltrs and removing complete all as specified and directed. 71 S&F Rotational moulded polyethlene water storage tanks of 1000 litres capacity (cylindrical vertical with closed top) with plastic lid cover, hoisted and fixedin position including PTMT Ball valves high pressure with epoxy coated aluminum rod & high density plastic ball complete, screwed for iron pipeor brass ferrule and fixed for 20 mm bore pipe including making connections complete all as specified and directed. 72 S&F in repair20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed . 73 Taking up or down 15mm dia GI tubing and conncetions including cleaning for refixing or removal to store complete all as specified and directed 74 Taking up or down 20 mm dia GI tubing and conncetions including cleaning for refixing or removal to store complete all as specified and directed 75 M&L for cutting (in brick walls) chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sun shades, shelves, Iintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting n.exc 10cm grith complete all as specified and driected. 76 S&F Galvanised steel tubing, 15mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed 77 S&F Galvanised steel tubing, 20mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed 78 Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings and removing from site complete all as specified and directed 79 S&F UPVC (SWR) type B pipes, 110 mm bore, single socketed, in any length with rubber ring joints,laid in floors/treaches orfixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed. 80 S&F UPVC (SWR) type B pipes, 75 mm bore, single socketed, in any length with rubber ring joints, laid in floors/treaches or fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed. 81 S&F UPVC (SWR) bends any radius, 75 mm bore complete all as specified and directed 82 S&F UPVC (SWR) bends any radius, 110 mm bore complete all as specified and directed 83 S&F UPVC (SWR), junction single, (single T)equal or unequal for 75 mm bore complete all as specified and directed 84 S&F UPVC (SWR), junction single, (single T)equal or unequal for 110 mm bore complete all as specified and directed 85 S&F in repair UPVC (SWR) floor trap plain with grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed. 86 S&F in repair UPVC (SWR) multi floor trap plain with grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed. 87 S&FUPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. 88 S&F UPVC (SWR)type-B vent cowl 75 mm dia complete all as specified and directed 89 S&F UPVC (SWR) type-B reducers 110 mm dia complete all as specified and directed. 90 Demolition of brick work or stone/boulder masonry , built in cement mortar or cement lime mortar including all quoins, arches & pillars etc of any description and in any position and removingunserviceable material from work site to outside defence premises complete all as specified and directed 91 M&L for brick work with sub class B bricks, using old size bricks, straight or curved on plan exceeding 6m mean radius , built in cement mortar 1:6 complete all as specified and directed 92 All as per Ser item No 91 here-in-before but except brick complete all as specified and directed. 93 M&L for brick work with old size sub-class B bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed . 94 M&L for glazed ceramic coloured digital tiles,300x600x7 mm thick, as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. 95 M&L for 7 to 8mm thick non skid coloured digital ceramicjoint less tiles (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding0.18 sqm, in floors etc, set and jointed in neat cement slurry and poined in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in cement motar 1:4 complete all as specified and directed. 96 M&Lfor 8 to 9 mm thick vitrifiedceramic coloured or printed,light shade,edge cut, joint free tiles (square/ rectangular) polishedarea of each tiles exceeding 0.42 sqm but not exceeding 1.0 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified anddirected . 97 M&Lfor 8 to 9 mm thick vitrifiedceramic coloured or printed,light shade,edge cut, joint free tiles (square/ rectangular) polishedarea of each tiles exceeding 0.42 sqm but not exceeding 1.0 sqm ,as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. . 98 M&L for 8 to 9 mm thick full body vitrifiedceramic (double charged), edge cut,joint free,coloured or printed, any shade tiles (square/ rectangular) polished,area of each tiles exceeding 0.36 sqm but not exceeding 0.72 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles using spacers & gap be filled with PU grout over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed. 99 M&L for 8 to 9 mm thick full body vitrifiedceramic double charged, edge cut,joint free,coloured or printed any shade tiles (square/ rectangular) polished,area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , as in vertical surfaces such as skirting / dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles using spacers & gap be filled with PU grout over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. 100 Dismantling oftimber scantlings40sqcm and over in section, framed work,in any position complete all as specified and directed 101 Dismantiling of steel/Asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings complete all as specified and directed 102 S&F Pre painted galvalume aluminium zinc coating (AZ-150 micron) GI basedplain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed . 103 S&F rolled mild steel work as in tank staging(framed), roof trusses (framed), trussed, purlins, crane gantries rails and fastening and heavy bracket framing (beam, tee, angle channel or flat sections) including distance pieces, cleats etc confirmimg to Fe 290 (Gde E -165)complete all as specified and directed . 104 Demolition of stone slab and tiles of any description or any thickness complete all as specified and directed. 105 S&F machine cut kota stone slab in flooring, treads of steps, 18-20 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing cutting and mirror polishing over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed. 106 M&L for machine cut kota stone slab 15-18 mm thick in riser of steps, skirting , dado and pillar, laid and jointed with grey cement slurry mixedwith pigment to match the shade of the slab including rubbing, cutting and mirror polishing over and including 10 mm thick rendering in cement mortar 1:4 after roughing surfaces of old concrete /any type of plaster by picking sweeping down with water to remove dust etc complete all as specified and directed. 107 S&F in repairsinks , madeof 1.0mm thick stainless steel,overall size of sink 495mm x 420mm with bowl size 410mm x 330mm x 160mm,plugs, washers, waste pipe, union, chromium plated waste coupling and cantilever brackets embedded in cement and sand mortar in wallcomplete all as specified and directed 108 M&L for 15mm thick renderingin cement mortar 1:3 on concrete surfaces as inroof,finished even & fair and including mixing of water proofing compound complete all as specified anddirected . Note:-WPC shall be measured and paid separately 109 Supply only liquid water proofing compound. 110 M&Lfor plain cement concrete 1:5:10 type E2 (using 40 mm graded crushed stone aggregates) in sunken filling(upto 2nd floor) and mass concrete complete all as specified and directed 111 M&L for glass fibre reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent).Base coat: Berger HS Latex plus (or equivalent) both on wall (upto 1 mtr min height) and floor.Consumption base coat: 0.3 kg/sqmReinforcement: Glass fiberSecond and Third coat: Latex sheild 2K (or equivalent) both on wall (upto 1 mtr min height) and floor.Consumption top coat: 3 kg/sqmSystem requirements: density: 2.00 kg/ltrcompressive strength: 0.5 N/mm².• Wall penetration through the RCC slab must be sealed using Berger HS RepirO(or equivalent).• Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus(or equivalent) modified mortar with a bonding coat of Berger HS Latexplus(or equivalent) modified cement slurry upto 5ft.• All depressions, unevenness, surface honeycombing shall be repaired using Berger HS Latex plus (or equivalent) modified polymer mortar with a bonding coat of Berger HS latex plus(or equivalent)modified cement slurry including cleaning ofRCCsurface to remove dust, loose particles, etc with compressed air or any other suitable technique depending on site conditions, grinding any sharp edges, etc 112 M&L for 15mm thick renderingin cement mortar 1:4 on concrete surfaces as inroof,finished even & fair and including mixing of water proofing compound complete all as specified anddirected . Note:-WPC shall be measured and paid separately 113 M&Lfor complete removal of existing water proofing treatment of any description including under layer, taking downcement plaster any thickness and removal of debris off the premisesincluding grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust and apply water proofing treatment inthe following sequences:-(a) Applying1st course of bituminous primer conforming to IS -3384 @ 0.4 Kg/Sqm cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely(b) Applying2nd coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm. (c)Applying 3rd course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.0 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat complete all as specified and as directed . (d) Complete treatment to be carried out by authorised applicator of waterproofing manufacturer. 114 M&L for applyingtwo coats of aluminium paint over APP membrane complete all as specified and directed 115 M&L for PCC 1:2:4 type B-0 (using 12.5mm gradedcrushed stone aggregates) as in padding, laid to required slope over roof finishing complete all as specified and directed. 116 Dismantlingwall and ceiling boards (fibre,pulp, insulation) or insulation boards/ slabs/blankets, any thickness, including cover fillets etc complete all as specified & directed. 117 S&FGI snap grid frame work (Grid size 60.5cm x 60.5cm) for false ceilingconsisting of main runner T of size 24mm x 32mm and 0.3mm thick , Secondary runner T of size 24mmx25mm and 0.3mm thick,GI angle24mmx24mm and 0.4mm thick,Bottom exposed capping of width 24 mm of all T-sections shall be of 0.25mm thick PPGI, hot dipped galvanised steel with zink coating not less than 120gm / Sqm ,ceiling grid system duly suspended by 4mm dia GI wire hanging from existing purlins /roof slab with butterfly clipsincluding Gypsum ceiling tilesof size 595 x 595 x 9 mm laminated with 0.07 mm thick polyvinyl film on the face side and 10 micron metalized polyester film on the back side fixed on GI snap gridcomplete all as specified and directed .. 118 M&L for 75 mm thick plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate), as in sub base offloors, finished even and fair complete all as specified anddirected 119 M&L for providing and laying 60 mm thick factory made charmfered edge cement concrete paver block of M-35 grade of approved colour, design & pattern as in foothpath, parks, lawns, drive ways or light traffic parking etc of required strength , thickness & size/ shape made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. 120 M&L for rendering 15mm thick in cement mortar 1:6 on brick work or concrete surfaces, surface finished even and smooth without using extra cement complete all s specified and directed. 121 M&L for rendering 15mm thick in cement mortar 1:4 on brick work or concrete surface, surface finished even and smooth without using extra cement complete all as specified and directed. 122 M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed. 123 M&L for 75mm thick PCC 1:3:6 , type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection, laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. surfaces finished even and fairincluding raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:2 complete all as specified and directed . 124 M&L for repairing of concrete surfaces such asbalcony, chajjas, upward or downward facia ,column, pillar, ceiling and similar itemswith plain cement concrete 1:2:4type B-0 (using 12.5mm thick crushed stone aggregates) or with 15mm thick renderingin cement mortar 1:3 without using extra cement,surfacefinished even and fair (as per site requirement)complete all as specifiedand directed.(Note:-Quoted rated shall be deemed to include:- (i) formwork and scaffolding required & taking down or dismantlingas per site requirement (ii) The work is to be executed upto 4th storey building 125 M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed 126 M&L for preparation of new or previously untreatedwood or wooden based surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 127 M&L for complete removal of existing treatment of wall/ceiling , roof projection, including facia, cornices, etc by scrapping with mechanical wall sander (having mechanical vaccum mechanical) having RPM not less than 1500, sanding pad of 60 grit having dia of 7/9 to make the surface free from dust, loose paint etc by skilled labour (up to 4th storey with necessary scaffolding) complete all as specified and directed 128 M&L for water proof cement based putty @ 1kg (undiluted) per sqm of average thickness 1 mm over the plastered painted exterior wall surfaces of walls (upto 4th storey with necessary scaffolding )including prepartion of surfaces by scarpping to prepare the surface and sanding of the putty surfaces with mechanical wall sander (having mechanical vaccum mechanism ) having RPM not less than 1500 ,sanding pads of 240 Grit or above to make the surface free from dust etc by skilled llabour as per following steps:-Steps 1:- Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of minimum 2.5 kg putty per minute.Step 2:- Apply the first coat of prepared mixer with the manually required help of fully automatic airless spary machine of putty application, finishing the surface even and smooth in level without any undulation.Step 3:- Allow 6 to 8 hour time to dry the putty surface, Apply the further more coat of preparaed mixer with the help of fully automatic airless spary machine of putty application, finishing the surface even and smooth in level without any undulation. 129 M&Lfor one coat of acrylic water based exterior grade primer @ 0.9 ltrs (undiluted) per 10 sqm, diluted with water in 1.1 ratio to be applied with fully automatic airless spary machine of paint application with a flow speed of min 1 litres per mintues having a pressure of 3300 PSI and Allow 6 to 8 hours to dry surface for painting of subbsequent coats (walls up to 4th storey with necessary scaffolding)complete all as specified and directed . 130 M&L for water based premium acrylic smooth interior emulsion of approved colour with silicon additive excellent dirt pick up resistance with low VOC less than 50 Antifugal, Anti Algai properities in two coats @ 1.79 lites (undiluted) per 10 Sqm diluted with water as per manufacturer instructions applied over priming surface in between subsequent coats of paint (upto 4th storey with necessary scaffolding) complete all as specified and directed . 131 M&L for water based premium acrylic smooth exterior emulsion of approved colour with silicon additive excellent dirt pick up resistance with low VOC less than 50 Antifugal, Anti Algai properities in two coats @ 1.79 lites (undiluted) per 10 Sqm diluted with water as per manufacturer instructions applied over priming surface in between subsequent coats of paint (upto 4th storey with necessary scaffolding) complete all as specified and directed .Notes for Srl item No 127to 131 of BOQ :- (a) The work for periodical services shall include the under mentioned aspects and the rates quoted by the bidder shall includes and the same & nothing extra shall be payable.(i) Workshall be carried out by the authorised applicator of manufacturer of water based premium acrylic smooth exterior emulsion, contractor shall submit a triparty agreement MoU (between contractor ,said manufacturer and their authorities appicator ) on Non judicial stamp paper to GE and shall be approved by the GE before commecement of work at site. (ii) Workshall be carried out up to 4th storey height buildings and the necessary scaffolding , trestles , ladders ,cradles & safety measures shall be arraged by the contractor for labour and their own .(iii) Removing of nails & making good holes, cracks etc. (iv) Work in patches and in narrow /widths ,bands ,cornises ,plasters etc shall also be carried out and cutting in edge of line where ncessary. (v) Spreading and removing covering to doors ,windows ,floor ,fittings etc to protect them from splashes.(vi) Washing floors , cleaning glass ,joinery, fittings, wiring etc from drops and splashes of paint to be cleaned to the statisfaction of Engineer-in-charge.(vii) Sample patch of 10 sqm be prepared considering all the items of periodical and shall be got approved from GE prior to carrying out further work. 132 M&L for 25 mm thick plain cement concrete 1:2:4,type B-0, (using 12.5 mm graded crushed stone aggregates) as in sub base/ levelling course of floors, finished even and faircomplete all as specified and directed. 133 M&L for preparation of new plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed. 134 Dismantling boarding, any description, fixed in any position with screws complete all as specified and directed 135 M&L for 5mm thick prelam PVC sheet in strips & channel feathered at the edges for fixing on solid PVC wall lining, Insulated PVC wall lining, and Solid PVC partitions inclusive of solvent cement and fixing at site complete all as specified and directed. 136 Grubbing up vegetation, small trees. fromroots ,clean the loose dirt with water, and repair the same portion with CM :1:3, tuchup with same finish, area not exc0.10 Sqm eachadjacent to CI pipeupto 4th storeybuilding with necessary scaffolding/ ladder complete all as specified and directed . 137 Surface dressingn.exc. 15 cm deep and getting out in any type of soilcomplete all as specified and directed. 138 Excavating in trenches, n. exc 1.5 m wide and n. exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n. exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed 139 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil complete all as specified and directed. 140 Removing excavated material to a distance n.exc 50 m & depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed . 141 M&L for plain cement concrete 1:4:8, type D2 (using 40mm graded crushed stone aggregates) as in foundation, filling & mass concrete complete all as specified and directed. 142 M&L for reinforced cement concrete M-25 (design mix)(using 20 mm graded crushed stone aggregates)as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed . 143 M&L for reinforced cement concrete M-25 (design mix)(using 20 mm graded crushed stone aggregates) as in column,pillars, piers and struts complete all as specified anddirected. 144 M&L foruse and waste offormwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified anddirected. 145 M&L for use and waste offormwork to sides of pillars, posts, struts, piers, columns, and stanchions etc complete all as specified anddirected . 146 M&L Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface completeall as specified and directed. 147 M&L for 100mm thick Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base, finishing surfaces even and fair complete all as specified and directed. 148 M&L for aluminum powder coated (coating not less than 50 micron), sliding window, two track withwindow style of section 44.4mmx44.5mmx 2.0mm thick including 4.0 mm thick coloured/tinted/frosted glass panes, aluminium grill of 6 mm dia and 100 x 100 mmand all necessary fittings and fixtures complete all as specified and directed. 149 M&L for preparation of new plastered surfaces of walls and applying two coats of premium water bound distemper over two coats of wall care putty 1 to 2 mm thick each and one coat of primer complete all as specified and directed. 150 M&L for preparation of new plastered surfaces of walls and applying two coats of premium weather proof exterior emulsion paint over one coat of wall care putty 1 to 2 mm thickand one coat of primer complete all as specified and directed. 151 Taking down carefully existing aluminium/copper point wiringfor light, fan, socket or power bell complete with fittings such as Switches, sockets, ceiling roses, holders, call bells etc & making goodthe disturbed surfaces of walls/ceiling, matching the colour with existing surface complete all as specified and directed.Note : Rate for making good shall be deemed to be included in above item rate. 152 Taking down ofunserviceableMCB DB, SPN /TPN along with MCBs complete all as specified and directed. 153 Taking down ofunserviceablesub main wiring of any size complete all as specified and directed. 154 Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLSH with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed medium grade conduit of suitable size with all accessories such as bend, reducers, MS hooks including modular galvanisedflush boxes of suitable size and white cover plate with frame as per relevant ISfor mounting modular switches, sockets, fan regulators etc including continuous earth wire of size 1.5 Sqmm PVC FRLSH stranded copper conductor unsheathed, insulated, strandedconnected to common earthpoint dolly for one light point/fan point/call bell point, 230 voltscontrolled by one switch complete all as specified and directed . Note:- Proper colour coding is to be followed as per IS specifications. 155 All as per srl item No 154 above but One 3 pin socket outlet 6 amp independentcomplete all as specifieds and directed 156 All as per srl item No 154 above but One 3 pin socket outlet 6 amp same board complete all as specifieds and directed 157 All as per srl item No 154 above but one light point controlled by one , two way switch 6 Amp complete all as specified and directed. 158 All as per srl item No 154 above but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire. 159 S&F modular type switch, one way 6 Amps , 1 module complete all as specifieds and directed . 160 S&F modular type switch, two way 6 Amps , 1 module complete all as specifieds and directed . 161 S&Fmodular type socket 3 pin, 6 Amps, 2 module complete all as specifieds and directed 162 S&F modular type switch, one way, 16 Amps, 1 module complete all as specifieds and directed . 163 S&Fmodular type socket 3 pin, 6 A/16 Amps,2 module complete all as specifieds and directed . 164 S&F ceiling rose, surface backelite, two/ three terminal, 240 volts complete all as specifieds and directed . 165 S&Fmodular bell push with indicator polycarbonate materials 6 Amp 240 volts 1 module complete all as specifieds and directed. 166 S&F musical door bellAC 240 volts single phase complete all as specified and directed. 167 S&F LED lightfitting 1 x 18Watt, 220V, Integrated batten type with driver, holder including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rosewith all fixing arrengenmentcomplete all as specified and directed. 168 S&F energy saving new generation 10W LED bulk head luminaire with opal diffuser, IP 65 and including connecting up with twin core twisted flexible copper coductor cable with suitable size of 230 volt,50 Hz complete all as specified and directed. 169 S&F MCB SPN,32 Amp, 240 Volts withrupturing capacity 10 KA, C series, complete all as specifieds and directed . 170 S&F MCB Single pole, 6 to 32 Amp, 240 Volts withrupturing capacity 10 KA, C series, complete all as specifieds and directed . 171 S&Fexhaust fan, steel body, AC single phase. 230 V of size 300 m sweep with, blades and frame and louvers, hanging on wall with 4 Nos steel fasterners 10mm dia & 100mm long includingwall hole and making good the disturbed surfaces as per existingcomplete allas specified & directed 172 S&F ceiling fan complete with blades,clamp, hooks,down rod and accessories, 230 V, 1200 mm sweep, min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC)with compatible regulator and fixing of hooks by anchor fastner including connecting from ceiling rose/connector with & including flexible copper cable of suitable size complete all as specified and directed 173 S&FSubmain wiring with two runs of single core PVC FRLSH unsheathed, insulated, copper cable of 4 Sqmm size, multi stranded, 1100 volts grade with PVC insulated,unsheathedFRLSH copper wire 4 Sqmm for continous earth wire drawn into and includingconcealed PVC conduit of suitable sizecomplete all as specifiedand directed . Note :- Two runs of 4 Sqmm copper cable and one run of 4 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length) 174 S&FSubmain wiring with two runs of single core PVC FRLSH unsheathed, insulated, copper cable of 6 Sqmm size, multi stranded, 1100 volts grade with PVC insulated,unsheathedFRLSH copper wire 6 Sqmm for continous earth wire drawn into and includingconcealed PVC conduit of suitable sizecomplete all as specifiedand directed . Note :- Two runs of 6 Sqmm copper cable and one run of 6 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length) 175 S&F Sheet metal enclosure for DBs,SPN, single door,IP-43 protected, 240 Volts,2 wayscomplete all as specified and directed 176 S&FMCCB four pole, 100 Amp, 16 KA, 415 volts with adjustable thermal settingscomplete all as specified and directed 177 S&F factory made epoxy polyester powder coated distribution board TP&N ,6 ways (VTPN DB), double door,(concealed flush to wall) (IP-43 protection) fabricated from minimum 1.2 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 250 Amps copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with space for provision for 4 pole MCCB as incommer and outgoing MCBs as required at siteand conforming to IS: 8623 along with cable end box including making good disturbed surface complete all as specified and directed.NOTE: (a) MCCBs and MCBs shall be measured and paid separately.(b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/ sleeves and its cost shall be deemed to be included under respective item of BoQ. 178 M&L for complete earthingwith galvanised mild steel earth plate electrode of size600x600x6mm thick, burried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1, precast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh ,15mm dialight grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specifieds and directed .. 179 Supply, laying, jointing, testing and commissioning of Low Tension (LT)XLPEinsulated, armoured, heavy duty, electric power cable, cross sectional area 70 Sqmm, 3.5 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, alongpolesorpassing through pipes or laid under floor or through walls etc, completeall as specified anddirected. 180 M&L for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment. 181 M&L for factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, laid flat and dryin trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed. 182 S&F Galvanised steeI tubing, light grade, 40mm bore, for cable protection, fixed to pole/wall with MS clamps, nuts, bolts etc or laid under floor/road/pavementcomplete all as specified and directed. 183 Supply, laying, jointing, testing and commissioning of Low Tension (LT)XLPEinsulated, armoured, heavy duty, electric power cable, cross sectional area 16 Sqmm, 2 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, alongpolesorpassing through pipes or laid under floor or through walls etc, completeall as specified anddirected. 184 S&FSheet metal enclosure for DBs,SPN, double door,IP-43 protected, 240 Volts,8 ways with 200 amps rated copper bus bar complete all as specified and directed 185 S&FSheet metal enclosure for DBs,SPN, double door,IP-43 protected, 240 Volts,12 ways with 200 amps rated copper bus bar complete all as specified and directed 186 S&F MCB SPN,40-63 Amp, 240 Volts withrupturing capacity 10 KA, C series, complete all as specifieds and directed .
