SPECIAL repair to Bldg No P-7/09 with attached toilet (OR living Accn) of IDSR and Provn of steel gate with support columns and side walls at main eccess of Bldg NoP-4/102 at Jammu Mil Stn under GE Satwari-- 1 Taking down shutter exc 1.0 sqm and n. exc 2.0 sqm each and removing from site complete all as specified and directed. 2 Taking down chowkats or frames with shutter (without taking off shutter from the frame) n. exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed. 3 Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 sqm & n. exc 4 sqm each includingcutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed. 4 S&F pressed steel frames of size 125mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including mild steel hinges, 100 mm long , medium weright and 25 mm x 3 mm flat iron as in hold fast , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed. 5 S&F pressed steel frames of size 105mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including mild steel hinges, 100 mm long , medium weright and 25 mm x 3 mm flat iron as in hold fast , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed. 6 S&F 35 mm thick 2nd class hard wood , glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers size of members of shutters as specified in SSR Part-I Section-8 clause 8.24 (a) fitted to chowkats complete all as specified and directed. 7 M&L for 30mm thick flush shutters, solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed. 8 S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to distributed surface of walls complete all as specified and directed. 9 S&F factory made solid panel PVCdoor shutter 30 mm thick ( style ) consisting of frame work made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour P.V.C‘ C’ channelhaving a PVC sheet strip 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top rail; and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement S&F in frame at site as per specification complete all as specified and directed. 10 S&F 100mm long stainless steel butt hinges, fixedwith screws complete all as specified and directed 11 S&F 100mm long mild steel butt hinges, medium weight ,fixedwith screws complete all as specified and directed 12 S&F aluminium anodised barrel tower bolts, 150mm long of extruded section, fixed to doors with screws complete all as specified and directed. 13 S&F aluminium anodised ,fabricated type handle 100mm size complete all as spcified and directed. 14 S&F aluminum alloy, anodised, sliding door bolt of length 250mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminum alloy and fixed complete all as specified and directed. 15 S&F aluminum hanging floor door stopper ,twin rubber of size 100mm, anodised (anodic coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour and shade with necessary screws complete all as specified and directed 16 S&Faluminium bottom door seal with brushes of length 1.2 m, suitable for wooden door,fixed with screwscomplete all as specified and directed. 17 S&F300 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate including fixing to pressed steel frames with necessary welding work complete all as speciied and directed 18 S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20gauge with stainless steel brackets near toends with stainless steelfinialsat both ends and necessary fittings complete all as specified and directed. 19 M&L for factory made box type steel windows/ventilators, double shutter,outer frame made out ERW TUBE P section (60x45x25mm) and shutters of ERW TUBE P section (50x35x20mm) openable shutters side hung including pintle hinges with two nos MS tower bolts 150mm size on each shutter, steel handleand stopper of Z section as specified complete with sash bars dovetailed or welded ready for glassfixing and wire gauzed fixing with suitable fittings/opening for cooler/AC where required steel windows will be double shutter (external glazed and internal wire gauzed) complete all as specified in Drg No CEPZ/TD-324/07 of sheet No 1/3 to 3/3 complete all as specified and directed. Note: - The quoted rate shall be deemed to include:-(i) 04 Nos MS steellugs of MS flat 20 x 5mm& 20 cm long over all welded to frames (ii) PCC block for embedding lugs. 20 M&L for framed work such as grills , gratings etc with ends of bars shouldered and /or riveted or forged into spikes , framed guard bars, barred iron doors, ladders, framed balusters: walk ways , railings frame work of water tanks and similar work confirmingto Fe290, Gde E-165 complete all as specifiedand directed 21 M&L for 3 mm thick, plain sheet glass, ordinary quality and glazing with oil putty or with any type of beadsin squares n. exc 0.5 sqm each pane complete all as specifiedand directed. 22 S&F 3 mm thick , figured glass, pin head type and glazing with oil putty or with any type of beads in squares n. exc 0.5 sqm each pane complete all as specified and directed. 23 S&F galvanised mild steel wire cloth , 0.56 mm normal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed. 24 S&F in repair bib taps,long body,chromium plated, fancy type, cast copper alloy with crutch or butterfly handle , screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed. 25 S&F in repair angle valve with flange,cast copper alloy , fancy type, chromium plated, screwed down for high pressure , screwed both ends for iron pipe of 15mm bore complete all as specified and dircted. 26 S&F in repair2 in 1 angle valve with flange,cast copper alloy , fancy type, chromium plated, screwed down for high pressure , screwed both ends for iron pipe of 15mm bore complete all as specified and dircted. 27 S&F in repair 15mm dia stop valve,fancy type, cast copper alloy ,chromium plated, concealed type with long shank and cup, screwed both ends for iron pipe complete all as specified and directed. 28 S&F in repair brass chromium plated tubular towel rail 20mm dia, D type , 600 mm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed. 29 S&F in repair sheet glass shelf assembly consisiting of 5.5 mm thick sheet glass, shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. 30 S&Fin repair PVC connection 15 mm x 600 mm including brass check nut at both ends complete all as specified and direced. 31 S&F in repair brass chromium plated shower rose 125 mm of size with arm and with or without swivel joints to steel pipe or union complete all as specified and as directed. 32 S&Fin repair corner glass shelf of size 30cm with Chromium plated bracket guard and railing fixed with and including screws and wooden/plastic cleats complete all as specified and directed . 33 S&F in repair chromium plated soap dish of size 160x160x90mm, any type, fixed to plugs with chromium plated brass screwscomplete all as specified and directed. 34 S&F in repair rust resistance stainless steel peg set of six complete all as specified and directed. 35 S&F in repair vitreous china counter wash basins, size 560x470x190mm, oval shape,white to be fixed on counter/ RCC slabincluding CP waste coupling & PVC waste pipe complete all as specified & directed. 36 S&F in repair 10 litres PVC, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float 32mm PVC L bend and handle including brackets complete all as specified and directed 37 S&F in repair Rotational moulded polyethlene water storage tanks of 1000 litres capacity (cylindrical vertical with closed top) with plastic lid cover, hoisted and fixedin position including PTMT Ball valves high pressure with epoxy coated aluminum rod & high density plastic ball complete, screwed for iron pipeor brass ferrule and fixed for 20 mm bore pipe including making connections complete all as specified and directed. 38 Disconnecting existing tanks of capacity upto 1000 ltrs, setting aside (or lowering if required) for repairs etc and hoisting if required, including cleaning and removingall scale and dirt ,etc from the the tank & from the mouths of circulating pipes etc,reconnecting and re-fixing in position complete all as specified and directed. 39 S&F in repair20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed . 40 S&F in repair15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed . 41 Taking up or down 15mm dia GI tubing and conncetions including cleaning for refixing or removal to store complete all as specified and directed 42 Taking up or down 20 mm dia GI tubing and conncetions including cleaning for refixing or removal to store complete all as specified and directed 43 S&F Galvanised steel tubing, 15mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed 44 S&F Galvanised steel tubing, 20mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed 45 M&L for cutting (in brick walls) chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sun shades, shelves, Iintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting n.exc 10cm grith complete all as specified and driected. 46 Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings and removing from site complete all as specified and directed 47 S&F UPVC (SWR) type B pipes, 110 mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. 48 S&F UPVC (SWR) type B pipes, 110 mm bore, single socketed, in any length with rubber ring joints fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed. 49 S&F UPVC (SWR) type B pipes, 75 mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. 50 S&F UPVC (SWR) type B pipes, 75 mm bore, single socketed, in any length with rubber ring joints fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed. 51 S&F UPVC (SWR) bends any radius, 75 mm bore complete all as specified and directed 52 S&F UPVC (SWR) bends with access door any radius, 75 mm bore complete all as specified and directed 53 S&F UPVC (SWR) bends any radius, 110 mm bore complete all as specified and directed 54 S&F UPVC (SWR) bends with access door any radius, 110 mm bore complete all as specified and directed 55 S&F UPVC (SWR), branch piece, (single Y) with access door equal or unequal for 75 mm bore complete all as specified and directed 56 S&F UPVC (SWR), junction single, (single T) with access door equal or unequal for 110 mm bore complete all as specified and directed 57 S&F UPVC (SWR) type-B reducers 110 mm dia complete all as specified and directed. 58 S&F UPVC (SWR) vent cowl 75 mm dia complete all as specified and directed 59 S&F in repair UPVC (SWR) floor trap plain with grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed. 60 S&FUPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. 61 Demolition of brick work or stone/boulder masonry , built in cement mortar or cement lime mortar including all quoins, arches & pillars etc of any description and in any position and removingunserviceable material from work site to outside defence premises complete all as specified and directed 62 M&L for brick work with sub class B bricks, using old size bricks, straight or curved on plan exceeding 6m mean radius , built in cement mortar 1:6 complete all as specified and directed 63 All as per Ser item No 62 here-in-before but except brick complete all as specified and directed. 64 M&L for brick work with old size sub-class B bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed . 65 M&L for plain cement concrete 1:2:4 ,type B1(using 20mm graded crushed stone aggregates) as in lintels upto 1.5m clear span, window or door cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings,side posts of precast jallies etc. including slightly rounded or chamfered angles including necessary formwork complete all as specified and directed. 66 Demolition of cement concrete (un-reinforced) ground floor to 4th floorand pavings n exc 15 cm thickness (below or above ground level ) and removingthe rubbish from the work site to out side defence premises complete all as specified and directed 67 Dismantling floor, hearth or wall tiling/ terrazzo dado from wall surface including cement mortar bedding, (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specied and directed. 68 M&L for glazed ceramic coloured digital tiles,300x450x7 mm thick, as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. 69 M&L for 7 to 8mm thick non skid coloured digital ceramicjoint less tiles (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding0.18 sqm, in floors etc, set and jointed in neat cement slurry and poined in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in cement motar 1:4 complete all as specified and directed. 70 M&L for granite (of any type) work 16 to 18 mm thick (table rubbed and polished) in steps, jambs , pillars, window cills , cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match shade of granite over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed 71 M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.. 72 M&L for 50mm thick PCC 1:3:6 , type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection, laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. surfaces finished even and fairincluding raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:2 complete all as specified and directed . 73 M&L for 75 mm thick plain cement concrete 1:3:6, type C2 (using 40 mm graded crushed stone aggregates) as in sub base and surface finished even and fair complete all as specified and directed 74 M&L for 25mm thick plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregates) as in sub base/ levelling course of floors, finished even and fair complete all as specified and directed. 75 S& F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed 76 Complete removal of existing water proofing treatment of any description including under layer, taking downcement plaster any thickness and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dustincluding filling cracks in existing roof surfaces with cement putty using suitable bonding agent before laying of padding and removal of debris off the premisesincluding grubbing up of trees complete all as specified and directed. 77 M&L for PCC 1:2:4 type B-0 (using 12.5mm gradedcrushed stone aggregates) as in roof padding, laid to required slopecomplete all as specified and directed. 78 M&L for 15mm thick renderingin cement mortar 1:4 on concrete surfaces as inroof,finished even & fair and including mixing of water proofing compound complete all as specified anddirected . Note:-WPC shall be measured and paid separately 79 M&L for preparation of surface free from dirt , dust & washing with water and water proofing treatment to roof surface (in four coat) with fibre reinforced elastometic liquid water proofing membrane formulated with PU hybrid polymers and reinforcing acrylic fibres with sun reflective index (SRI) of 100-110 having minimum elongation of 350%, tensile strength 2.9 MPa and shall have rack bridging ability upto 2.55 mm and shall resist 10 bars of hydrostatic pressure reduce temperature upto 10 degree celcius to RCC roof slabs, roof treatment shall be carried out in four coats to newly plaster roof surface as per the procedure given below :-(a) Apply first coat of fibre reinforced elastometic liquid water proofing membrane as described above with 33% dilution as priming coat as directed and allow it to dry before next coating. (b) Laying second coat of fibre mesh 0.3 mm thickness weave in leno pattern having weight 45 gms per sqm and pasting it properly with overlap of 50 mm as directed and allow it to dry before next coating.(c) Apply third coat of fibre reinforced elastometric liquid water proofing membrane as described in para (a) above but undiluted @ 0.45 litre per sqm of roof surface as directed.(d) Apply fourth and final coat of fibre reinforced elastometric liquid water proofing membrane as described in para (a) above but undiluted @ 0.45 litre per sqm of roof surface as directed.(e)Workshall be carried out by the authorised applicator of manufacturer and shall be approved by the GE before commecement of work at site. 80 Supply only liquid water proofing compound. 81 Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubing down with water etc and removing unserviceable material outside defence land complete all as specified and directed. 82 M&L for rendering 10mm thick in cement mortar 1:6 on brick work or concrete surfaces, surface finished even and smooth without using extra cement complete all s specified and directed. 83 M&L for rendering 15mm thick in cement mortar 1:4 on brick work or concrete surface,surface finished even and smooth without using extra cement complete all as specified and directed. 84 M&L for rendering 10 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed. 85 M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed 86 M&L for preparation of new or previously untreatedwood or wooden based surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 87 M&L for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described by rubbing with sand paper or grindingby hand grinderto make surface even and smooth & apply primer where required and applying one coat of synthetic enamel paint complete all as specified and directed. 88 M&L for complete removal of existing treatment of wall/ceiling , roof projection, including facia, cornices, etc by scrapping with mechanical wall sander (having mechanical vaccum mechanical) having RPM not less than 1500, sanding pad of 60 grit having dia of 7/9 to make the surface free from dust, loose paint etc by skilled labour (up to 4th storey with necessary scaffolding) complete all as specified and directed 89 M&L for water proof cement based putty @ 1kg (undiluted) per sqm of average thickness 1 mm over the plastered painted exterior wall surfaces of walls (upto 4th storey with necessary scaffolding )including prepartion of surfaces by scarpping to prepare the surface and sanding of the putty surfaces with mechanical wall sander (having mechanical vaccum mechanism ) having RPM not less than 1500 ,sanding pads of 240 Grit or above to make the surface free from dust etc by skilled llabour as per following steps:-Steps 1:- Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of minimum 2.5 kg putty per minute.Step 2:- Apply the first coat of prepared mixer with the manually required help of fully automatic airless spary machine of putty application, finishing the surface even and smooth in level without any undulation.Step 3:- Allow 6 to 8 hour time to dry the putty surface, Apply the further more coat of preparaed mixer with the help of fully automatic airless spary machine of putty application, finishing the surface even and smooth in level without any undulation. 90 M&Lfor one coat of acrylic water based exterior grade primer @ 0.9 ltrs (undiluted) per 10 sqm, diluted with water in 1.1 ratio to be applied with fully automatic airless spary machine of paint application with a flow speed of min 1 litres per mintues having a pressure of 3300 PSI and Allow 6 to 8 hours to dry surface for painting of subbsequent coats (walls up to 4th storey with necessary scaffolding)complete all as specified and directed . 91 M&L for water based premium acrylic smooth interior emulsion of approved colour with silicon additive excellent dirt pick up resistance with low VOC less than 50 Antifugal, Anti Algai properities in two coats @ 1.79 lites (undiluted) per 10 Sqm diluted with water as per manufacturer instructions applied over priming surface in between subsequent coats of paint (upto 4th storey with necessary scaffolding) complete all as specified and directed . 92 M&L for water based premium acrylic smooth exterior emulsion of approved colour with silicon additive excellent dirt pick up resistance with low VOC less than 50 Antifugal, Anti Algai properities in two coats @ 1.79 lites (undiluted) per 10 Sqm diluted with water as per manufacturer instructions applied over priming surface in between subsequent coats of paint (upto 4th storey with necessary scaffolding) complete all as specified and directed .Notes for Srl item No 88to 92 of BOQ :- (a) The work for periodical services shall include the under mentioned aspects and the rates quoted by the bidder shall includes and the same & nothing extra shall be payable.(i) Workshall be carried out by the authorised applicator of manufacturer of water based premium acrylic smooth exterior emulsion, contractor shall submit a triparty agreement MoU (between contractor ,said manufacturer and their authorities appicator ) on Non judicial stamp paper to GE and shall be approved by the GE before commecement of work at site. (ii) Workshall be carried out up to 4th storey height buildings and the necessary scaffolding , trestles , ladders ,cradles & safety measures shall be arraged by the contractor for labour and their own .(iii) Removing of nails & making good holes, cracks etc. (iv) Work in patches and in narrow /widths ,bands ,cornises ,plasters etc shall also be carried out and cutting in edge of line where ncessary. (v) Spreading and removing covering to doors ,windows ,floor ,fittings etc to protect them from splashes.(vi) Washing floors , cleaning glass ,joinery, fittings, wiring etc from drops and splashes of paint to be cleaned to the statisfaction of Engineer-in-charge.(vii) Sample patch of 10 sqm be prepared considering all the items of periodical and shall be got approved from GE prior to carrying out further work. 93 Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided and including removing from site to a distance n exc 500 mtrs , complete all as specified and as directed. 94 M&L for reinforced cement concrete 1:2:4 type B-1, nominal mix(using 20mm graded crushed stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconiescomplete all as specified and directed. 95 M&L for mildsteel TMTbars 10mm dia and over, cutto length, bent to shape required, including cranking, bendingspirallyforhooping forcolumn, hookingendandbinding withandincludingmildsteelwire(annealed) not lessthan0.9 mm dia orsecuring with clips, complete all as specifiedand directed . 96 M&L for use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for fair finished surfaces of concrete, complete all as specified and directed. 97 M&L for use and wasteof formwork to edges of concrete flats, treads, breaks in floors,window cills,concrete railings, openings in concrete walls, floor and roofs, n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n. exc 15cm widefair finished surface complete all as specified and directed . 98 Dismantling oftimber scantlings40sqcm and over in section, framed work,in any position complete all as specified and directed 99 Dismantiling of steel/asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings complete all as specified and directed 100 S&F Pre painted galvalume aluminium zinc coating (AZ-150 micron) GI basedplain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed . 101 S&F rolled mild steel work as in tank staging(framed), roof trusses (framed), trussed, purlins, crane gantries rails and fastening and heavy bracket framing (beam, tee, angle channel or flat sections) including distance pieces, cleats etc confirmimg to Fe 290 (Gde E -165)complete all as specified and directed . 102 S&F in repair vitreous china squatting pan, Orissa pattern, size 580 x 440mm white with integral foot rest, cast iron P or S trap of size 100mm, including provision of plain cement concrete bedding and connection to trap and to flushing pipe, anti syphonage pipe etc and making good the floors complete all a specified and directed 103 S&F in repair vitreous china wash down water closet pan (pedestal pattern) of size 520x360x390mm white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes, connecting only to flushing cistern, anti-syphonage pipe with PVC flush pipe of 32mm dia including plastic seat with cover, white in colour with mild steel chromium plated hinging and P or S trap device complete all as specified and directed 104 S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connectios and fixed in position complete all as specified and directed. 105 S&F Vitreous china urinal of size 375x390x590mm,whiteincluding providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, flush pipe, grating and union for discharge pipe andchromium plated spreader including Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm borecomplete all as specified and directed. 106 S&F in repair chromium plated urinal spreader complete all as specified and directed. 107 Dismantling of stone slabs and tiles of any description or thickness in floor, laid, bedded and pointed in any mortarcomplete all as specified and directed, 108 S&F machine cut kota stone slab in flooring, treads of steps, 18-20 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing cutting and mirror polishing over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed. 109 M&L for machine cut kota stone slab 15-18 mm thick in riser of steps, skirting , dado and pillar, laid and jointed with grey cement slurry mixedwith pigment to match the shade of the slab including rubbing, cutting and mirror polishing over and including 10 mm thick rendering in cement mortar 1:4 after roughing surfaces of old concrete /any type of plaster by picking sweeping down with water to remove dust etc complete all as specified and directed. 110 M&L for rubbing and mirror polishing on marble/granite/kota stone/ stone work where ever required to give high gloss finish complete all as specified and directed. 111 S&Fin repair GI snap grid frame work (Grid size 60.5cm x 60.5cm) for false ceilingconsisting of main runner T of size 24mm x 32mm and 0.3mm thick , Secondary runner T of size 24mmx25mm and 0.3mm thick,GI angle24mmx24mm and 0.4mm thick,Bottom exposed capping of width 24 mm of all T-sections shall be of 0.25mm thick PPGI, hot dipped galvanised steel with zink coating not less than 120gm / Sqm ,ceiling grid system duly suspended by 4mm dia GI wire hanging from existing purlins /roof slab with butterfly clipsincluding Gypsum ceiling tilesof size 595 x 595 x 9 mm laminated with 0.07 mm thick polyvinyl film on the face side and 10 micron metalized polyester film on the back side fixed on GI snap gridcomplete all as specified and directed .. 112 Excavating in trenches, n. exc 1.5 m wide and n. exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n. exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed 113 M&L for plain cement concrete 1:4:8, type D2 (using 40mm graded crushed stone aggregates) as in foundation, filling & mass concrete complete all as specified and directed. 114 M&L foruse and waste offormwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified anddirected. 115 M&L for use and waste offormwork to sides of pillars, posts, struts, piers, columns, and stanchions etc complete all as specified anddirected . 116 M&L for reinforced cement concrete M-25 (design mix)(using 20 mm graded crushed stone aggregates)as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed . 117 M&L for reinforced cement concrete M-25 (design mix)(using 20 mm graded crushed stone aggregates) as in column,pillars, piers and struts complete all as specified anddirected. 118 M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups , spacers and binders including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. 119 M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed. 120 Removing excavated material to a distance n.exc 50 m & depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed . 121 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil complete all as specified and directed. 122 M&L for preparation of newplastered/concrete surfaces of walls andapplying two coats of cement base paint over one coat of primer complete all as per specified and directed. 123 Taking down carefully existing aluminium/copper point wiringfor light, fan, socket or power bell complete with fittings such as Switches, sockets, ceiling roses, holders, call bells etc & making goodthe disturbed surfaces of walls/ceiling, matching the colour with existing surface complete all as specified and directed.Note : Rate for making good shall be deemed to be included in above item rate. 124 Taking down ofunserviceableMCB DB, SPN /TPN along with MCBs complete all as specified and directed. 125 Taking down ofunserviceablesub main wiring of any size complete all as specified and directed. 126 Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLSH with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed medium grade conduit of suitable size with all accessories such as bend, reducers, MS hooks including modular galvanisedflush boxes of suitable size and white cover plate with frame as per relevant ISfor mounting modular switches, sockets, fan regulators etc including continuous earth wire of size 1.5 Sqmm PVC FRLSH stranded copper conductor unsheathed, insulated, strandedconnected to common earthpoint dolly for one light point/fan point/call bell point, 230 voltscontrolled by one switch complete all as specified and directed . Note:- Proper colour coding is to be followed as per IS specifications. 127 All as per srl item No 126 above but One 3 pin socket outlet 6 amp independentcomplete all as specifieds and directed 128 All as per srl item No 126 above but One 3 pin socket outlet 6 amp same board complete all as specifieds and directed 129 All as per srl item No 126 above but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire. 130 S&F modular type switch, one way 6 Amps , 1 module complete all as specifieds and directed . 131 S&Fmodular type socket 3 pin, 6 Amps, 2 module complete all as specifieds and directed 132 S&F modular type switch, one way, 16 Amps, 1 module complete all as specifieds and directed . 133 S&Fmodular type socket 3 pin, 6 A/16 Amps,2 module complete all as specifieds and directed . 134 S&Fmodular type fan regulator step down 120 watt, 2 modulecomplete all as specified and directed . 135 S&F ceiling rose, surface backelite, two/ three terminal, 240 volts complete all as specifieds and directed . 136 S&F LED lightfitting 1 x 18Watt, 220V, Integrated batten type with driver, holder including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rosewith all fixing arrengenmentcomplete all as specified and directed. 137 S&F energy saving new generation 10W LED bulk head luminaire with opal diffuser, IP 65 and including connecting up with twin core twisted flexible copper coductor cable with suitable size of 230 volt,50 Hz complete all as specified and directed. 138 S&FSheet metal enclosure for DBs,SPN, double door,IP-43 protected, 240 Volts,8 ways with 200 amps rated copper bus bar complete all as specified and directed 139 S&F MCB SPN,32 Amp, 240 Volts withrupturing capacity 10 KA, C series, complete all as specifieds and directed . 140 S&F MCB Single pole, 6 to 32 Amp, 240 Volts withrupturing capacity 10 KA, C series, complete all as specifieds and directed . 141 S&FSubmain wiring with two runs of single core PVC FRLSH unsheathed, insulated, copper cable of 6 Sqmm size, multi stranded, 1100 volts grade with PVC insulated,unsheathedFRLSH copper wire 6 Sqmm for continous earth wire drawn into and includingconcealed PVC conduit of suitable sizecomplete all as specifiedand directed . Note :- Two runs of 6 Sqmm copper cable and one run of 6 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length) 142 S&Fexhaust fan, steel body, AC single phase. 230 V of size 300 mm sweep with, blades and frame and louvers, hanging on wall with 4 Nos steel fasterners 10mm dia & 100mm long includingwall hole and making good the disturbed surfaces as per existingcomplete allas specified & directed 143 Taking down existing ceiling fan of any size/sweep including oiling, greasing, cleaningand applying two coats of synthetic enamel paint after preparation of surface and refixingthe same complete all as specified and directed . 144 S&F ceiling fan complete with blades,clamp, hooks,down rod and accessories, 230 V, 1200 mm sweep, min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC)with compatible regulator and fixing of hooks by anchor fastner including connecting from ceiling rose/connector with & including flexible copper cable of suitable size complete all as specified and directed 145 S&F factory made epoxy polyester powder coated distribution board TP&N ,4 ways (VTPN DB), double door,(concealed flush to wall) (IP-43 protection) fabricated from minimum 1.2 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 250 Amps copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with space for provision for 4 pole MCCB as incommer and outgoing MCBs as required at siteand conforming to IS: 8623 along with cable end box including making good disturbed surface complete all as specified and directed.NOTE: (a) MCCBs and MCBs shall be measured and paid separately.(b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/ sleeves and its cost shall be deemed to be included under respective item of BoQ. 146 S&FMCCB four pole, 100 Amp, 16 KA, 415 volts with adjustable thermal settingscomplete all as specified and directed 147 M&L for complete earthingwith galvanised mild steel earth plate electrode of size600x600x6mm thick, burried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1, precast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh ,15mm dialight grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specifieds and directed .. 148 Supply, laying, jointing, testing and commissioning of Low Tension (LT)XLPEinsulated, armoured, heavy duty, electric power cable, cross sectional area 50 Sqmm, 3.5 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, alongpolesorpassing through pipes or laid under floor or through walls etc, including taking down existing one completeall as specified anddirected. 149 M&L for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment. 150 M&L for factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, laid flat and dryin trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed. 151 S&F Galvanised steeI tubing, light grade, 40mm bore, for cable protection, fixed to pole/wall with MS clamps, nuts, bolts etc or laid under floor/road/pavementcomplete all as specified and directed.
