special Repair To Bldg No Np-28 (Otm) At Rani Ka Bagh Of Guards And Spl Repair To Bldg No T-85 (01 To 04 Qtrs) Jcos Md Accn Of Med Regt Under Age B/R-Ii Of Ge Satwari-- 1 Taking down shutter exc 1.0 sqm and n. exc 2.0 sqm each and removing from site complete all as specified and directed. 2 Taking down chowkats or frames with shutter (without taking off shutter from the frame) n. exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed. 3 Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 sqm & n. exc 4 sqm each includingcutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed. 4 Taking down shutter exc 1.0 sqm and n. exc 2.0 sqm each and refixing after repair complete all as specified and directed. 5 S&F pressed steel frames of size 125mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, lock strike plate, hold fasts andincluding PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed. 6 S&F pressed steel frames of size 105mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, lock strike plate, hold fasts andincluding PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed. 7 S&F factory made 35 mm thick 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framingplain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkats complete all as specified and directed 8 S&F 35 mm thickfactory made 2nd class hard wood, plain, framed, panelled shutters (two panels) with lock rail and panel of 9mm thick BWP commercial plywood .The size of rail and stiles as per IS: 1003(Part-1), kiln seasoned and chemically pressure treated, fitted to chowkats complete all as specified and directed. 9 S&F factory made solid panel PVCdoor shutter 30 mm thick ( style ) consisting of frame work made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour P.V.C‘ C’ channelhaving a PVC sheet strip 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top rail; and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement S&F in frame at site as per specification complete all as specified and directed. 10 S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to distributed surface of walls complete all as specified and directed. 11 S&F Factory Made Solid PVC wood grain printed Moulded Door Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded prelamPVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specified and directed 12 S&F steel window/ventilator 1.25 mm thick Box type (Double Shutter) ERW hollow P section of size 60 mm x 25 mm single rebated comprises glazed & wire gauged skelton shutter ERW sec 50 mm x 20 mm and 1 mm thick with two Nos sash bar of T- section 20 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window including following fitting welded to frame shutter hold fast of 150 mm long of 12 mm x 3 mm FI made to shape 4 No, handle of Z section 20 mm x 25 mm x 100 mm long 1 No per leaf, MS tower bolt 150 mm long 2 No per leaf, Z sec 20 mm x 25 mm, 100 mm long stopper 1 No on per leaf, MS pintal hinges of size 75 mm x 12 mm 2 No per leaf fabrication, as per drg No CEPZ/TD-324,325 complete all as specified and directed. 13 M&L for framed work such as grills , gratings etc with ends of bars shouldered and /or riveted or forged into spikes , framed guard bars, barred iron doors, ladders, framed balusters: walk ways , railings frame work of water tanks and similar work confirmingto Fe290, Gde E-165 complete all as specifiedand directed 14 S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20gauge with stainless steel brackets near toends with stainless steelfinialsat both ends and necessary fittings complete all as specified and directed. 15 S&F galvanised mild steel wire cloth , 0.56 mm normal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed. 16 M&L for 3 mm thick, plain sheet glass, ordinary quality and glazing with oil putty or with any type of beadsin squares n. exc 0.5 sqm each pane complete all as specifiedand directed. 17 S&F 3 mm thick , figured glass, pin head type and glazing with oil putty or with any type of beads in squares n. exc 0.5 sqm each pane complete all as specified and directed. 18 S&F aluminum alloy, anodised, sliding door bolt of length 250mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminum alloy and fixed complete all as specified and directed. 19 S&F aluminium anodised barrel tower bolts, 200mm long of extruded section, fixed to doors with screws complete all as specified and directed. 20 S&F100mm long mild steel butt hinges, medium weight, cold rolledfixed with screws/welding complete all as specified and directed. 21 S&F140 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. 22 S&F300 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate including fixing to pressed steel frames with necessary welding work complete all as speciied and directed 23 S&F aluminium anodised ,fabricated type handle 150mm size complete all as spcified and directed. 24 M&L for preparation of new or previously untreatedwood or wooden based surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 25 M&L for preparation of old painted wood and wood based surfaces of any description over 10cm width or girth not otherwise described by grinding the uneven surfaces and necessary filling of putty (as and where required) to make surface even and smooth and applying one coat of synthetic enamel paint complete all as specified and directed. 26 M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed 27 M&L for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described by rubbing with sand paper or grindingby hand grinderto make surface even and smooth & apply primer where required and applying one coat of synthetic enamel paint complete all as specified and directed. 28 Dismantling boarding of any description, fixed in any position with screws complete all as specified and directed. 29 M&L for prelaminated particle board 18/19 mm thick as in shutters /shelves/partition (exterior grade) prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including teak wood edging alroundcomplete all as specified and directed. 30 S&F hasp & staple 100 mm in length, safety type, aluminum anodised with steel hinge pin including bolt to hinge plate fixed with screws complete all as specified and directed. 31 S&F in repair plate rack made of 1.0mm thick stainless steel of size 900mmx775mmx250mm fixed with steel fastners or steel screws complete all as specified and directed 32 Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubing down with water etc and removing unserviceable material outside defence land complete all as specified and directed. 33 M&L for rendering 15mm thick in cement mortar 1:6 on brick work or concrete surfaces, surface finished even and smooth without using extra cement complete all s specified and directed. 34 M&L for rendering 15mm thick in cement mortar 1:4 on brick work or concrete surface,surface finished even and smooth without using extra cement complete all as specified and directed. 35 M&L for rendering 10 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed. 36 M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over two coats of wall care putty 1 mm thick each and one coat of primer complete all as specified and directed. 37 M&L for preparation of old decorated concrete/ plastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with sand paper and applying one coat of oil bound distemper over one coat of wall care putty of 1 mm thick on uneven surface as and where required complete all as specified and directed. 38 M&L for preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper over one coat of wall care putty 1 mm thick complete all as specified and directed on ceiling. 39 M&L for preparation of old decorated surfaces of ceiling and applying two coats of white wash complete all as specified and directed. 40 M&L for preparation of new plastered surfaces of walls and applying two coats of weather proof exterior emulsion paint over one coat of primer complete all as specified and directed. 41 M&L for preparation of old decorative plastered/concreat surface of wall, chajja, facia, face of columns, beam ect by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with sand paper and applyingone coat of weather proof exterior emulsion paint over one coat of primer complete all as specified and directed. 42 M&L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and directed. 43 Dismantling floor, hearth or wall tiling/ terrazzo dado from wall surface including cement mortar bedding, (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specied and directed. 44 M&Lfor 8 to 9 mm thick vitrifiedceramic coloured , joint free light shade tiles (square/ rectangular) polishedarea of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified anddirected . 45 M&L for 7 to 8mm thick non skid colouredceramic,joint less tiles (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding0.18 sqm ,,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified anddirected . 46 M&L for glazed ceramic colouredtiles,300x450x7 mm/350x250x7mm thick, as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. 47 S&F machine cut kota stone slab in flooring, treads of steps, 20-25 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing cutting and mirror polishing over and including 20 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed. 48 M&L for granite work 16 to 18 mm thick (table rubbed and polished) in steps, jambs , pillars, window cills , cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match shade of granite over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed 49 Taking up or down 15mm dia GI tubing and conncetions including cleaning for refixing or removal to store complete all as specified and directed 50 Taking up or down 20 mm dia GI tubing and conncetions including cleaning for refixing or removal to store complete all as specified and directed 51 S&F Galvanised steel tubing, 15mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed 52 All as per Ser item No 51 here-in-before but except pipe complete all as specified and directed 53 S&F Galvanised steel tubing, 20mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed 54 All as per Ser item No 53 here-in-before but except pipe complete all as specified and directed 55 S&F in repairstop valve, cast copper alloy, screwed down for high pressurewith crutch or butter fly handle,screwedboth endsfor ironpipe of 15mm bore complete all as specified and directed. 56 S&F in repair stop valve, cast copper alloy, screwed down for high pressurewith crutch or butter fly handle,screwedboth endsfor ironpipe of 20mm bore complete all as specified and directed. 57 S&F in repair angle valve ,cast copper alloy , fancy type, chromium plated, screwed down for high pressure,screwed both ends for iron pipe of 15mm bore complete all as specified and dircted. 58 S&F in repair vitreous china squatting pan, Orissa pattern, size 580 x 440mm white with integral foot rest, cast iron P or S trap of size 100mm, including provision of plain cement concrete bedding and connection to trap and to flushing pipe, anti syphonage pipe etc and making good the floors complete all a specified and directed 59 S&F in repair 10 litres PVC, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float 32mm PVC L bend and handle including brackets complete all as specified and directed 60 S&F in repair vitreous china wash hand basin, white, flat back of size 550x400mm including cutting for and pinning in ends of brackets or erecting stand including cast iron brackets, brass chromium plated waste coupling 32mm bore, waste pipe PVC 32mm bore complete all as specified and directed 61 S&F in repair 15mm dia stop valve , fancy type, cast copper alloy ,chromium plated, concealed type with long shank and cup, screwed both ends for iron pipe complete all as specified and directed. 62 S&F in repair brass chromium plated shower rose 125 mm of size with arm and with or without swivel joints to steel pipe or union complete all as specified and as directed. 63 S&F in repair brass chromium plated tubular rail 20mm dia, D type , 600 mm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed. 64 S&F in repair Rotational moulded polyethlene water storage tanks of 1000 litres capacity (cylindrical vertical with closed top) with plastic lid cover, triple layered, white hoisted and fixedin position including PTMT Ball valves high pressure with epoxy coated aluminum rod & high density plastic ball complete, screwed for iron pipeor brass ferrule and fixed for 20 mm bore pipe including making connections complete all as specified and directed. 65 S&F in repairsinks with drainnage board , madeof 1mm thick stainless steel,overall size of sink 915mm x 460mm with bowl size 410mm x 330mm x 160mm,plugs, washers, waste pipe , union, CP waste coupling and cantilever brackets embedded in cement and sand mortar in wallcomplete all as specified and directed . 66 S& F600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed 67 S&F in repair sheet glass shelf assembly consisiting of 5.5 mm thick sheet glass, shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. 68 S&F in repair bib taps,long body,chromium plated, fancy type, cast copper alloy with crutch or butterfly handle , screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed. 69 Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings and removing from site complete all as specified and directed 70 S&F PVC (SWR) type B pipes, 110 mm bore, single socketed, in any length with rubber ring joints,laid in trenches or in floors or fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed.. 71 S&F PVC (SWR) type B pipes, 75 mm bore, single socketed, in any length with rubber ring joints,laid in trenches or in floors or fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed.. 72 S&F PVC (SWR) type B pipes, 50 mm bore, single socketed, in any length with rubber ring joints,laid in trenches or in floors or fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed.. 73 S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed 74 S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed 75 S&F PVC (SWR) bends with access door any radius, 110 mm bore complete all as specified and directed 76 Demolition of brick work or stone/boulder masonry , built in cement mortar or cement lime mortar including all quoins, arches & pillars etc of any description and in any position and removingunserviceable material from work site to outside defence premises complete all as specified and directed 77 M&L for brick work with sub class B bricks, using old size bricks, straight or curved on plan exceeding 6m mean radius , built in cement mortar 1:6 complete all as specified and directed 78 M&L for 75mm thick PCC 1:3:6 , type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection, laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. surfaces finished even and fairincluding raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed . 79 Demolition of cement concrete (un-reinforced) ground floorand pavingsexc 15 cm thickness (below or above ground level ) and removingthe rubbish from the work site to out side defence premises complete all as specified and directed 80 Excavation in trenches in any type of soil, not exceeding 1.5m deep and 1.5m wide for foundation etc or manholes, piers , shafts etc not exceeding 10 Sqm on plan & not exceeding 1.5m in depth and getting out complete all as specified and directed. 81 Returning , filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed 82 Removing excavated material to a distance n. exc 50m& depositing whrere directed at a level n exc 1.5 m above the starting point complete all as specified and directed. 83 M&Lfor Mild steel TMT bars 10 mm dia and over, cut to length bent to shape as required including cranking bending and binding with & including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. 84 M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups , spacers and binders including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. 85 M&L for RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in foundation including rafts, footings, foundation beams , plinth beams , bases of columns etc complete all as specified and directed. 86 M&L for RCC 1: 2:4 type B-1 (using 20mm gradded crushed stone aggregates) as in Columns, pillars, piers, posts and struts etc complete all as specified anddirected . 87 M&L for use and waste of form work to sides of concrete foundations, footings, bases of columns , raft and raft beams, sides and softfits (if any) of foundation and plinth beams and similar work, verticalor batter for rough finished surfaces of concrete complete all as specified and directed. 88 M&L for use and waste offormwork to sides of pillars, posts, struts, piers, columns, and stanchions etcfor fair finished surfaces of concrete complete all as specified and directed. 89 S&F in repair PVC (SWR) floor trap plain with grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed. 90 S&F PVC (SWR) vent cowl 75 mm dia complete all as specified 91 S&F in repair PVC (SWR) floor trap plain with grating having diameter of outlet 63 mm for WHB including 40mm dia HDPE pipe jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed. 92 S&F in repair PTMT cabinet with mirror of size450x350mm fixed with screws complete all as specified & directed 93 Complete removal of existing water proofing treatmentof any description including under layer, taking down of cement plaster/demolition of cement concrete of any thickness and removal of debris off the premises including grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel bushes and cleaning with water to remove all loose dirt/dust complete all as specified and directed. 94 M&L for PCC 1:2:4 type B-0 (using 12.5mm gradedcrushed stone aggregates) as in padding, laid to required slope over roof finishing complete all as specified and directed. 95 Cleaning of the exposed concrete slab and repairing the surface irregularities, potholes, as per manufacturersmethodstatement by Berger HS Rapairo (or equivalent) along with HS Latex Plus (or equivalent) & cement in mixing ratio 1:4 where ever required complete all as specified and directed. 96 M&L for HomeSheild PU Roofkoat(or equivalent) is a one component liquid ,solvent free , cold applied , water-proofing membrane that is highly elastic and UV resistant with 10 years warranty .ASTM D 6083-97 a Waterproofing and heat reflecting system having following key performance properties:-a) UV resistant ,prevent yellowing and weatheringb)Highly elastic upto 350% and crack bridgingc) Excellent adhesion on porous and non-porous substratesd) Tensile Strength >10 N/mm2 with GeoTextile fleecee) Soler Reflective Index (SRI) more then 109-111ASTM E1980-11System: First coat:Providing and applying primer over the prepared surface with HS PU roofkoatPrimer(or equivalent)Coverage: 0.2kg/sqm(with 50% dilution of water)Reinforcement: Geotextile 40 gsmSecond coat:Home sheildroofkoat(or equivalent)Consumption: 0.5 kg/sqm.Third coat: HS PU roofkoat(or equivalent)Consumption : 0.8 kg/sqm.System buildup-1.5kg/sqm with geotextile of 40gsm. 97 Demolition of cement concrete (un-reinforced) groundfloorand pavings n exc 15 cm thickness (below or above ground level) and removing the rubbish from the work site to out side defence premises complete all as specified and directed 98 M&L for glass fibre reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent).Base coat: Berger HS Latex plus (or equivalent) both on wall (upto 1 mtr min height) and floor.Consumption base coat: 0.3 kg/sqmReinforcement: Glass fiberSecond and Third coat: Latex sheild 2K (or equivalent) both on wall (upto 1 mtr min height) and floor.Consumption top coat: 3 kg/sqmSystem requirements: density: 2.00 kg/ltrcompressive strength: 0.5 N/mm².• Wall penetration through the RCC slab must be sealed using Berger HS RepirO(or equivalent).• Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus(or equivalent) modified mortar with a bonding coat of Berger HS Latexplus(or equivalent) modified cement slurry upto 5ft.• All depressions, unevenness, surface honeycombing shall be repaired using Berger HS Latex plus (or equivalent) modified polymer mortar with a bonding coat of Berger HS latex plus(or equivalent)modified cement slurry including cleaning ofRCCsurface to remove dust, loose particles, etc with compressed air or any other suitable technique depending on site conditions, grinding any sharp edges, etc 99 M&L for rendering 10mm thick in cement mortar 1:4 with water proofing compound on brick work or concrete surface,surface finished even and smooth without using extra cement complete all as specified and directed. Note : WPC to be measured and paid separately) 100 M&L for steel water tubing of 40 mm bore,medium grade,galvanised, laid in sunken floors as spout complete all as specified and directed. 101 S&Fin repair PVC waste pipe 32mm bore for sink /WHB of required length complete all as specified and directed. 102 M&L for preparationof newplastered/ concrete surfaces of wallsandapplying two coats of cement base paint over one coat of primercomplete all asspecified andas directed. 103 Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushingsurface with neat cement slurry with 3.0 kg of cement per sq.metre and removing unserviceable material outside defence land complete all as specified and directed 104 S&F in repair pillar taps, chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe of 15mm bore complete all as specified and directed. 105 M&L for PVC soap shelf white in colour of size 450x125x40mm complete all as specified and directed. 106 S&F in repair bib taps, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle , screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed. 107 M&L for 100 mm bore cast iron bend (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed. 108 M&L for 75 mm bore cast iron bend (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed. 109 S&Fcast iron floor trap, 100mm dia with stainless steel grating including jointing to waste pipe, fixed in cement concrete type B1(1:2:4) complete all as specified and directed 110 S&Fcast iron cowl, 75mm diacomplete all as specified and directed 111 Demolition of Cement Concrete (un-reinforced)of any description and in any position not otherwise specifically provided and including removing from site to a distance n exc 500 mtrs , complete all as specified and as directed. 112 Supply only liquid water proofing compound. 113 M&L for15mm thick renderingon floor and wall of sunken floors, in cement mortar 1:4, mixed with & including liquid integral water proofing compound @0.20 Ltr per 50 kg bag of cementafter proper curing and drying and applying Epoxy resins coating polymer modified cementation coating like brush bond of Fosroc Pidilite and Bostic as per manufacturers instructionscomplete all as specified and directed. 114 Dismantiling of Asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings complete all as specified and directed 115 S&F Pre painted galvalume aluminium zinc coating (AZ-150 micron) GI basedcorrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed . 116 S&F Pre painted galvalume aluminium zinc coating (AZ-150 micron) GI basedplain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed . 117 Dismantlingwall and ceiling boards (fibre,pulp, insulation) or insulation boards/slabs/ blankets, any thickness, including cover fillets etc complete all as specified & directed. 118 S&FGI snap grid frame work (Grid size 605mm x 605mm) for false ceilingconsisting of main runner T of size 24mm x 32mm and 0.3mm thick , Secondary runner T of size 24mmx25mm and 0.3mm thick,GI angle24mmx24mm and 0.4mm thick,Bottom exposed capping of width 24 mm of all T-sections shall be of 0.25mm thick PPGI, hot dipped galvanised steel with zink coating not less than 120gm / Sqm ,ceiling grid system duly suspended by 4mm dia GI wire hanging from existing purlins /roof slab with butterfly clipsincluding Gypsum ceiling tilesof size 595 x 595 x 7 mm laminated with 0.07 mm thick polyvinyl film on the face side and 10 micron metalized polyester film on the back side fixed on GI snap gridcomplete all as specified and directed .. 119 Taking down carefully existing aluminium/copper point wiringfor light, fan, socket or power bell complete with fittings such as Switches, sockets, ceiling roses, holders, call bells etc & making goodthe disturbed surfaces of walls/ceiling, matching the colour with existing surface complete all as specified and directed.Note : Rate for making good shall be deemed to be included in above item rate. 120 Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLSH with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed medium grade conduit of suitable size with all accessories such as bend, reducers, MS hooks including modular galvanisedflush boxes of suitable size and white cover plate with frame as per relevant ISfor mounting modular switches, sockets, fan regulators etc including continuous earth wire of size 1.5 Sqmm PVC FRLSH stranded copper conductor unsheathed, insulated, strandedconnected to common earthpoint dolly for one light point/fan point/call bell point, 230 voltscontrolled by one switch complete all as specified and directed . Note:- Proper colour coding is to be followed as per IS specifications. 121 All as per srl item No 120 above but One 3 pin socket outlet 6 amp independentcomplete all as specifieds and directed 122 All as per srl item No 120 above but One 3 pin socket outlet 6 amp same board complete all as specifieds and directed 123 All as per srl item No 120 above but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire. 124 S&F modular type switch, one way 6 Amps , 1 module complete all as specifieds and directed . 125 S&Fmodular type socket 3 pin, 6 Amps, 2 module complete all as specifieds and directed 126 S&F modular type switch, one way, 16 Amps, 1 module complete all as specifieds and directed . 127 S&Fmodular type socket 3 pin, 6 A/16 Amps,2 module complete all as specifieds and directed . 128 S&Fmodular bell push with indicator polycarbonate materials 6 Amp 240 volts 1 module complete all as specifieds and directed. 129 S&F bell ding dong AC 230 volts single phase complete all as specified and directed. 130 S&F modular type fan regulator, step down 120 Watt, 2 module complete all as specifieds and directed. 131 S&F lamp holder,PVC /Polycarbonate type with back plate for batten fittings complete all as specifieds and directed .. 132 S&F ceiling rose, surface backelite, two/ three terminal, 240 volts complete all as specifieds and directed . 133 S&F LED lightfitting 1 x 10Watt, 220V,decorative box type with driver, holder including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rosewith all fixing arrengenmentcomplete all as specifieds and directed . 134 S&F LED lightfitting 1 x 18Watt, 220V, Integrated batten type with driver, holder including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rosewith all fixing arrengenmentcomplete all as specified and directed. 135 S&F MCB SPN,40-63 Amp, 240 Volts withrupturing capacity 10 KA, C series, complete all as specifieds and directed . 136 S&F MCB Single pole, 6 to 32 Amp, 240 Volts withrupturing capacity 10 KA, C series, complete all as specifieds and directed . 137 S&FSheet metal enclosure for DBs,SPN, double door,IP-43 protected, 240 Volts,8 ways with 200 amps rated copper bus bar complete all as specified and directed 138 S&FSubmain wiring with two runs of single core PVC FRLSH unsheathed, insulated, copper cable of 4 Sqmm size, multi stranded, 1100 volts grade with PVC insulated,unsheathedFRLSH copper wire 6 Sqmm for continous earth wire drawn into and includingconcealed PVC conduit of suitable sizecomplete all as specifiedand directed . Note :- Two runs of 4 Sqmm copper cable and one run of 4 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length) 139 M&L for complete earthingwith galvanised mild steel earth plate electrode of size600x600x6mm thick, burried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1, precast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh ,15mm dialight grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and directed .
