Tender For Certain Sanctioned Special Repair And Revenue Works At Damana Under Ge Jammu-- 1 B/R Portion: -Demolition of brick work built in cement mortar including all quoins, arches, pillars etc. complete all as specified and as directed. 2 Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and complete removal of debris outside MOD land complete all as specified and as directed. 3 Dismantling floors hearth or wall tilling including cement mortar bedding (but not backing) removing unserviceable materials outside MOD area and rubbish off the premises complete all as specified and as directed. 4 Demolition of stone slabs and tiles of any description or thickness in floors/ walls laid bedded and pointed in any mortar etc. complete all as specified and as directed. 5 Dismantling PVC water tank/ demolition of RCC water storage tanks of capacity exceeding 250 but not exceeding 500 litres and removing from site complete all as specified and as directed. 6 Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and as directed. 7 Excavation in post holes (or similar holes) each not exceeding 0.5 cum getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm with soft/ loose soil complete all as specified and as directed. 8 Removal excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed. 9 Hardcore of gauge exceeding 63mm but not exceeding 100mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rolled/rammed to a true surface with broken bricks complete all as specified and as directed. 10 Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each, including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish (without any extra cost to Govt) and removing from site complete all as specified and as directed by Engineer-in-Charge. 11 Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm and not exceeding 4 Sqm each, including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish (without any extra cost to Govt) and removing from site complete all as specified and as directed by Engineer-in-Charge. 12 Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each complete all as specified and as directed by Engineer-in-Charge. 13 Taking up or down steel tubing with connections for cleaning for refixing or removing or storeyard complete of bore 15mm all as specified and as directed. 14 Taking up or down steel tubing with connections for cleaning for refixing or removing or storeyard complete of bore 20mm all as specified and as directed. 15 Taking down cement plaster of any description on brick walls, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, etc. complete removal of debris outside MOD land (including all necessary scaffolding, lifting arrangement upto 12 mtr height) complete all as specified and as directed. 16 Complete removal of existing treatment and preparation of ceiling and applying two coats of distemper oil bound over primer coat complete all as specified and as directed by Engineer-in-Charge. 17 Complete removal of existing treatment and preparation of surface and applying wall care putty on old surface of walls and applying two coats of distemper Oil bound over primer coat complete all as specified and as directed by Engineer-in-Charge. 18 Removing existing treatment from roof surfaces such as tiling, tarfelt, fungus, moss, dust etc., cleaning the surface of all foreign material by wire brushing and dusting and racking out RCC slab complete all as specified and removing the debris outside defence land all as directed. 19 Brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6 mtr mean radius built in cement mortar (1:6) complete all as specified and as directed. 20 Plain cement concrete (1:2:4) type B-0 (using 12.50mm graded crushed stone aggregate) 25mm thick as in sub base for floor tiles complete all as specified and as directed. 21 Plain cement concrete (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete, RCC sunken portion as base layer for receiving top layer complete all as specified and as directed by Engineer-in-Charge. 22 Providing cement concrete (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) in roof padding, roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed. 23 PCC 75mm thick (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) in plinth protection/path/Hardstanding finished even and fair complete all as specified and as directed. 24 Cement concrete (1:5:10) type E-2 (using 40mm graded crushed stone aggregate) in foundation filling, sub base and mass concrete complete all as specified and as directed. 25 75mm thick cement concrete (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) in base and mass concrete complete all as specified and as directed. 26 Rendering 5mm thick on fair faces of concrete surface of ceiling in cement mortar (1:3), surface finished even and smooth surface without using extra cement complete all as specified and as directed. 27 Rendering 10mm thick on fair faces of brick work or concrete surface in cement mortar (1:6) surface finished even and smooth without using extra cement complete all as specified and as directed. 28 Rendering 15mm thick in cement mortar (1:4) on fair faces of brick surface finished even and fair including water proofing compound all as specified (including all necessary scaffolding, lifting arrangement upto 12 mtr height) all as directed. 29 Glass fibre reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent) in sunken treatement. Base coat : Berger HS Latex plus (or equivalent), Consumption base coat : 0.3 Kg/Sqm, Reinforcement : Glass fiber, Second and Third coat : Latex shield 2K (or equivalent), Consumption top coat: 3 Kg/Sqm, System requirements : density: 2.00 Kg/Ltr, Compressive strength : 0.5 N/Sqmm. (i) Wall penetration through the RCC slab must be sealed using Berger HS Repir (or equivalent). (ii) Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus (or equivalent) modified mortar with a bonding coat of Berger HS Latexplus (or equivalent) modified cement slurry upto 1.5 Mtr. (iii) All depressions, unevenness, surface honeycombing shall be repaired using Berger HS Latex plus (or equivalent) modified polymer mortar with a bonding coat of Berger HS latex plus (or equivalent) modified cement slurry, including cleaning of RCC surface to remove dust, loose particles, etc with compressed air or any other suitable technique depending on site conditions, grinding any sharp edges, etc complete all as specified and as directed. 30 Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. fixed with approved tile adhesive and provided with 4mm spacer, spacer gaps to be filled with approved epoxy grout complete all as specified and as directed by Engineer-in-Charge. 31 Non-skid ceramic tiles 7 to 8 mm thick (square/rectangular) in vertical surface such as skirting, dado etc. fixed with approved tile adhesive and provided with 4mm spacer, spacer gaps to be filled with approved epoxy grout complete all as specified and as directed by Engineer-in-Charge. 32 Non-skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile not exceeding 0.18 Sqm, in floors etc. fixed with approved tile adhesive and provided with 4mm spacer, spacer gaps to be filled with approved epoxy grout complete all as specified and as directed by Engineer-in-Charge. 33 Glazed ceramic tiles 300 x 450 x 7mm thick on vertical surface such as in skirting, dado etc. fixed with approved tile adhesive and provided with 4mm spacer, spacer gaps to be filled with approved epoxy grout complete all as specified and as directed by Engineer-in-Charge. 34 Granite (of any type) 16-20mm thick (tabled rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in colour cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in cement mortar (1:6) edges of slab to be rounded from all sides (including cutting, wastage and polishing) complete all as specified and as directed. 35 Material and labour sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed. 36 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar (1:3) (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not be more than 5mm), including making drainage opening whereever required complete all as specified and as directed. 37 Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and no pigment complete all as specified and as directed. 38 Factory made pressed steel frames of size 105 x 60mm made out of PBI sheet 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete including bottom of each chowkhat to be welded with 02 nos 25 x 25 x 3mm angle iron projecting 10cm on either side including PCC (1:3:6) type C-0 in back filling of chowkhats and two coats of synthetic enamel paint over one shop coat of zinc chromate primer on all exposed surface complete and one coat of tar on the ends of steel surface in contact with bricks/ concrete surface. Colour/ shade will be approved by Engineer-in-Charge all as specified and as directed. 39 Factory made pressed steel frames of size 125 x 60mm made out of PBI sheet 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinge, lock strike plate etc. complete including bottom of each chowkhat to be welded with 02 nos 25 x 25 x 3mm angle iron projecting 10cm on either side including PCC (1:3:6) type C-0 in back filling of chowkhats and two coats of synthetic enamel paint over one shop coat of zinc chromate primer on all exposed surface complete and one coat of tar on the ends of steel surface in contact with bricks/ concrete surface. Colour/ shade will be approved by Engineer-in-Charge complete all as specified and as directed. 40 30 mm thick flush shutters, solid core construction, with particle board core and ply wood face panels, commercial type on both sides with lipping/ frame to match complete all as specified and as directed. 41 35mm thick factory made second class hard wood, glazed and skelton shutter open rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR 2009 Pt-I Section 8.24 (b) supplied and fitted to chowkhats complete all as specified and as directed. 42 Pre-painted (factory painted) box type mild steel windows/ Ventilator (factory made) outer frame made out ERW tube P section 65 x 45 x 25 mm and shutter of ERW tube P section 50mm x 35mm x 20mm openable (double shutter) with glazed shutter on external side and gauzed shutter fixed with galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm including necessary GI wire staples etc on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 nos on each shutter stopper of Z section and its locking arrangementand mild steel hook and eyes suitable for fixing cooler/ AC window complete all as specified and shown on drawings No CEPZTD-324/07 Sh 1/3 to 3/3 all as directed. Notes: - The quoted rates shall also include: - (i) Two coats of synthetic enamel paint over one shop coat of zinc chromate primer on all exposed surface complete and one coat of tar on the ends of steel surface in contact with bricks/ concrete surface. Colour/ shade will be approved by Engineer-in-Charge. (ii) 4 nos MS steel lugs made of 20 x 5 mm Iron flat 200 mm long. (iii) 10 mm Sq Bar grill/ guard bar design as per drawing. (iv) PCC block for embedding lugs incl back filling of PCC complete. (iv) Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete. (v) 3mm thick ordinary glass sheet quality and glazing with oil putty including glazing pins or spring clips. 43 Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows and other frames/ chowkhat of size 45 x 70 mm (+5 mm) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed stainless steel screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm², modules of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with mild steel hold fast/ lugs/ stainless steel dash fasteners of required dia and length complete as per directions of Engineer-in-Charge all as specified. 44 28 to 30mm thick (stile) factory made solid PVC moulded door shutter with wood free EPS, with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supply and fixing in frame at site as per specifications and drawing shown in SSR complete all as specified and as directed. 45 18mm thick factory made prelaminated solid PVC board for wardrobe shutter/ kitchen cabinet shutter/ shelves in any colour including PVC edge tape for edging of all around of shutters and exposed faces of same colour in repair complete all as specified and as directed. 46 Preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed. 47 Preparing of new plastered surface of ceiling and applying two coats of distemper oil bound over primer coat complete all as specified and as directed by Engineer-in-Charge. 48 Preparing of new plastered surface of wall and applying wall care putty and applying two coats of distemper oil bound over primer coat complete all as specified and as directed by Engineer-in-Charge. 49 New plastered surface of wall surface and applying exterior wall care putty and acrylic smooth exterior paint of required shade (Two coats over and including priming coat of exterior primer applied as per manufacturer instructions) (including all necessary scaffolding, lifting arrangement upto 12 mtr height) complete all as specified and as directed. 50 Cleaning of the exposed concrete slab and repairing the surface irregularities like cracks, potholes, as per manufacturers method statement by Berger HS Rapairo (or equivalent) along with HS Latex Plus (or equivalent) and cement in mixing ratio of (1:4) whereever required complete all as specified and as directed. 51 Home Shield PU Roofkoat (or equivalent) is a one component liquid, solvent free, cold applied, waterproofing membrane that is highly elastic and UV resistant with 10 years Warranty. ASTM D 6083-97a Waterproofing and heat reflecting system having following key performance properties. (i) UV resistant, prevent yellowing and weathering. (ii) Highly elastic upto 350% and crack bridging. (iii) Excellent adhesion on porous and non-porous substrates. (iv) Tensile Strength >10 N/Sqmm with GeoTextile fleece. (v) Solar Reflective Index (SRI) more than 109-111 ASTM E 1980-11. System : First coat : Providing and applying primer over the prepared surface with HS PU roofkoat Primer (or equivalent), Coverage : 0.2Kg/Sqm (with 50% dilution of water), Reinforcement : Geotextile 40 gsm, Second coat :Home shield roofkoat (or equivalent), Consumption : 0.5 Kg/Sqm, Third coat : HS PU roofkoat (or equivalent), Consumption : 0.8 Kg/Sqm. System buildup - 1.5Kg/Sqm with geotextile of 40 gsm complete all as specified and as directed. 52 Painting to steel surfaces of any description over 10 cm in width or girth not otherwise described for two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. 53 Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof of AZ 150 covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed. 54 Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof of AZ 150 covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed. 55 Structural steel works of Fe 410W (Gde E 250) quality A, as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc including painted one shop coat of zinc chromate/ red oxide primer paint (including preparation of surface) before fabrication complete all as specified and as directed. 56 Plates (plain or chequered channels, square cut or notched ordinary and counter sunk) forming holes Fe-410 W (Gde E-250) quality B without any attachment complete all as specified and as directed. 57 Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 22.5 cm and not exceeding 30cm long, diameter of neck 16mm to 20mm complete all as specified and as directed. 58 Stainless steel auto closing hinges for fixing in kitchen cabinet shutter/ wardrobe shutter with self closing mechanism which allows the cabinet door to closesmoothly complete all as specified and as directed by Engineer-in-Charge. 59 Supply and fixing 100mm hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and as directed. 60 Butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised 100 mm long complete all as specified and as directed. 61 Aluminium anodised bow handle fabricated type extruded section of 150mm long complete all as specified and as directed. 62 Aluminium anodised barrel tower bolts of extruded section 150mm long complete all as specified and as directed. 63 300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed. 64 Mild steel helical door spring 300mm including roller and roller plate complete fixed with welding to existing steel chowkhats complete all as specified and as directed. 65 150 mm over all length of cover plate of floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor complete all as specified and as directed by Engineer-in-Charge. 66 Curtain rods, mild steel, chromium plated with fixing brackets, stops, side finnels etc complete with all fittings in repair complete all as specified and as directed. 67 Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed. 68 Rotational moulded polyethylene water storage tanks 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part - I, including 20mm ball valves, 20mm tank nipple complete all as specified and as directed by Engineer-in- Charge. 69 25mm outer dia CPVC gate valves in repair complete all as specified and as directed by Engineer-in-Charge. 70 20mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings on concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete in repair all as specified and as directed. 71 25mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings on concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete in repair all as specified and as directed. 72 Stainless steel sink with drainage board made out of 1.00mm thick sheet for kitchen with plug, washers, waste pipe, connecting union overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm including 32mm bore PTMT waste coupling, fixing in cement mortar onto dwarf wall or fixing cantilever brackets in repair complete all as specified and as directed. 73 Stainless steel plate rack of size 750 x 600 x 250mm of size having partition as per sample kept in AGE B/R office and fixed with steel fasteners or steel screwed in repair complete all as specified and as directed. 74 Vitreous china wash down water closet (Pedestal Pattern) white (excluding flushing cistern and flush pipe) including PVC seat cover white closed pattern with recessed bottom and connection to drain or outgoing pipe and flushing pipe in repair complete all as specified and as directed. 75 10 litres capacity PVC low level flushing cistern including 32mm dia PVC flush pipe, fixing in position with PVC connection pipe of 15mm x 450mm long etc in repair complete all as specified and as directed. 76 Vitreous china wall hang corner wash hand basin, size 400 x 400 x 195mm including 32mm bore PTMT waste coupling, waste pipe and PVC connection pipe of 15mm x 450mm long in repair complete all as specified and as directed.Make: - Cera Cat Part No : S2040161 or equivalent in makes as mentioned in Group - 1 of Appx F. 77 600mm x 450mm bevelled edge mirror of selected quality, glass 5mm thick, mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. 78 15mm bore chromium plated cast copper alloy bib taps fancy type with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule in repair complete all as specified and as directed by Engineer-in-Charge. 79 15mm bore chromium plated wall mixer with bend pipe for overhead shower pipe for mixing hot and cold water with connecting legs and wall flanges screwed down for iron pipe and fixed in repair complete all as specified and as directed.Make: - Cera Cat Part No : F2006402 or equivalent in makes as mentioned in Group - 1 of Appx F. 80 15mm bore chromium plated Basin/ Sink mixer for mixing hot and cold water screwed down for iron pipe in repair complete all as specified and as directed by Engineer-in-Charge. 81 15mm dia Angle/ Stop cock of chromium plated, glossy finish in repair complete all as specified and as directed. 82 Brass chromium plated shower rose 125mm size with or without swivel joints any size including fixing to steel pipe of 15mm bore in repair complete all as specified and as directed by Engineer-in-Charge. 83 Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position in repair complete in all respect as specified and as directed. 84 Tubular towel rail 20mm dia D type 60cm long between flanges chromium plated in repair complete all as specified and as directed. 85 PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement etc in repair complete all as specified and as directed. 86 Supply and fixing in repairs 110mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls/ floor etc complete all as specified and as directed. 87 Supply and fixing in repairs 75mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls/ floor etc complete all as specified and as directed. 88 PVC (SWR) bends/ Single Tee / Y 110mm dia any radius with access door in repair complete all as specified and as directed. 89 PVC (SWR) bends/ Single Tee / Y 75 mm dia any radius with access door in repair complete all as specified and as directed. 90 PVC (SWR) vent cowl 110mm bore in repair complete all as specified and as directed. 91 PVC (SWR) vent cowl 75mm bore in repair complete all as specified and as directed. 92 E/M Portion: -Taking down old unserviceable copper/aluminium point wiring concealed/ batten (light, fan, socket or power) complete including fixtures and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type of switch board wooden/iron, round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed. 93 Taking down carefully unserviceable TPN and MCB DBs of any type/ size with TPN/ MCBs and disconnecting and making good disturbed surfaces complete all as specified and as directed. 94 Sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 6 Sqmm for phase and neutral and one run of 6.0 Sqmm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length including taking down old wiring complete all as specified and as directed. 95 Complete point wiring with 1.5 Sqmm two single core multistranded copper conductor FRLS insulated and unsheathed heavy duty cable in colour code including continuous earth wire with cable of size 1.5 Sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall, plastering after concealing conduit, including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc and including making good the disturbed surface as per existing complete all as specified and as directed by Engineer-in-Charge for the following: - 96 Description all as per Ser item No 95.00 here-in-before but for multi 5 pin 5 amp socket outlet on same board ISI marked complete all as specified and as directed. 97 Description all as per Ser item No 95.00 here-in-before but for multi 5 pin socket outlet 5 amp socket on independent board ISI marked complete all as specified and as directed. 98 Description all as per Ser item No 95.00 here-in-before but for One bell/buzzer point controlled by one push button on the same board with other switches or independent with cable 1.5 Sqmm size complete all as specified and as directed. 99 Description all as per Ser item No 95.00 here-in-before but for multi 6 pin 15 Amp socket outlet independent controlled by 15 Amp switch with 2.5 Sqmm copper conductor multistranded cable PVC insulated FRLS and unsheathed cable in and including PVC rigid concealed conduit 20/25 mm dia and unsheathed copper conductor multistranded cable 2.5 Sqmm as earth wire FRLS PVC insulated in green color complete all as specified and as directed by Engineer-in-Charge. 100 Modular socket, 6A - 5 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed. 101 Modular switch 1 module 6A, 1 module, 240 volts ISI marked complete all as specified and as directed. 102 Modular bell push 6A, 1 module, 240 volts ISI marked complete all as specified and as directed. 103 Ceiling rose, 3 Pin/ PVC/ polycarbonate isolated body ISI marked complete all as specified and as directed. 104 Modular switch 1 way 16A, 1 module, 240 volts ISI marked complete all as specified and as directed. 105 Modular socket 6A/16A - 6 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed. 106 Calling bell Ding Dong/ buzzer AC 230 Volts, single pole ISI marked complete all as specified and as directed. 107 Modular lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed. 108 Self ballast LED retrofit lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and as directed. 109 LED light fitting 10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. 110 LED light fitting 1 x 20W, 220V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.9, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. 111 Vertical Distribution Board (V.TP&N) 4 way double door wall mounted suitable for TPN 4 pole 100 Amp 16 KA four pole as incomer, it should be IP-43 protected and copper bus bars for neutral links, Earthing bar complete all as specified and as directed. 112 Distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and as directed by Engineer-in-Charge.Note: - Distribution board and MCBs should be of same make. 113 SPN 40 to 63 Amp rating 240V, 10 KA B curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed. 114 MCB 240V, 10 KA B curve miniature circuit breaker (MCB) of single pole and current carrying capacity 6 to 32 Amp complete with connection, testing and commissioning complete all as specified and as directed. 115 Earthing complete with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC (1:2:4) type B-1 pre-cast RCC cover slab using reinforcement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and as directed. 116 LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP-65/66 protection complete all as specified and as directed. 117 MCB 415V 10 KA B curve miniature circuit breaker (MCB) TPN 4 Pole, upto 125 Amps of following poles and current carrying capacity in the distribution board complete with connection testing and commissioning complete all as specified and as directed. 118 Fan step regulator, 100W - 1 module 240 volts ISI marked complete all as specified and as directed. 119 Supply and laying, connecting and testing XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 volts grade 16 Sqmm 4 core laid in trenches/ on poles/ road crossing or passing through existing/ new pipe under road crossing, clamping on wall etc including taking out of old unsv cable complete all as specified and as directed. 120 Exhaust fan, steel body AC single phase 230V of size 300mm sweep with blades, frame and louvers inculding making holes on existing wall for 300 mm dia exhaust fan. Plastering/ Painting for making good to the original surfaces of any description complete all as specified and as directed. 121 Ceiling fans complete with blades, down rods, electronic regulator and accessories, 230V, 1200 mm sweep five star rated with brushless direct current motor (BLDC) complete all as specified and as directed. 122 Supply and laying, connecting and testing XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 volts grade 16 Sqmm 2.0 core laid in trenches/ on poles/ road crossing or passing through existing/ new pipe under road crossing, clamping on wall etc. complete all as specified and as directed.Note: - (i) Earth work, sand, bricks, removing, returning filling aluminium thimbles/lugs will be paid separately.
