Tender For B R Maintenance And Periodical Services Of Accn In Pallanwala Mil Stn And Its Outstations Under Ge(South) Akhnoor-- 1 M & L for preparation of old decorated plastered or un-plastered surface of ceiling and applying one coat of white wash complete all as specified. 2 M &L for preparation of old surfaces of walls plastered or unplastered and applying one coat of exterior emulsion paint, complete all as specified and as directed . 3 M & L for preparation of old plastered or new plastered surfaces of walls and applying two coats of wall care putty, including preparation of surfaces/grinding of surafce as required before applying any paint or oil emulsion, complete all as specified and directed 4 M & L for preparation of old painted surfaces of wood or wood based surface of any description over 10 cm with or girth and painted with one coat of synthetic enamel paint all specified. 5 M & L for preparation of old painted surfaces of steel of any description over 10cm with or girth and painted with one coat of synthetic enamel paint all specified. 6 Demolition of brickwork or stone/ boulder masonry, built in cement mortar including allquoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and as directed . 7 Brickwork with subclass ‘B’ bricks, old size bricks, straight or curved on plan exceeding 6.0mtrs mean radius built in cement mortar 1:6, complete all as specified and as directed . 8 Brickwork with subclass ‘B’ bricks, old size bricks, straight or curved on plan exceeding 6.0mtrs mean radius built in cement mortar 1:6 but except bricks, complete all as specified and as directed . 9 Taking down cement or cement lime plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water, etc. 10 Rendering 10mm thick on bricks or concrete masonry surfaces,on walls, in cement mortar 1:6, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed . 11 Rendering 15mm thick on fair faces of brick work or concrete surfaces, in cement mortar 1:4, rendering is to be finished even and smooth (without using extra lime or cement), complete all as specified and as directed . 12 M & L for preparationof new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a primer coat of chalk whitening, complete all as specified and as directed . 13 M & L for preparationof new plastered or unplastered surfaces of walls and applying two coats of cement based paint over primer coat of alkali resistant primer, complete all as specified and as directed . 14 M & L for preparation of old decorated plastered or un plastered surface of walls and applying one coat of cement base paint of any tint to match existing shade of walls including removing moulds, efflloroscent salts and greasy spots complete all as specified. 15 Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as specified and as directed . 16 S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and as directed . 17 S&F pre- painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and as directed . 18 Dismantling wall and ceiling boards (fibre, pulp, insulation etc), or insulation boards/slabs/blankets, any thickness any type including cover fillets, complete all as specified and directed. 19 Providing and fixing Ceiling board of 4mm thick, designer, in ceiling fixed as per manufacturer’s instructions, including powder coated galvanised iron snap grid frame work of main and tee (weight not less than 240gm/Rm), angle (weight not less than 217 gm/Rm), grid size 595x595mm, for false ceiling all as specified, and hangers 6mm dia, galvanised iron (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of galvanised iron wire of 4.0mm dia, length as required at site and expansion hold fasteners 12.50mm dia, 40mm long incl dismantlingof wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets,complete all as specified and as directed . 20 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed. 21 M & L for glazed ceramicjointless tiles in vertical surface/ dado, size 350x250x6/7mm thick or 350x450x6/7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match, the shade/ colour of tiles including laid over 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed. 22 M & L for non-skid, coloured, ceramic tiles 7 to 8 mm thick of size 400 x 400 mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and laid over and including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and as directed . 23 M & L for non-skid, coloured, ceramic tiles 7 to 8 mm thick of size 600 x 600 mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and laid over and including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and as directed . 24 M & L for non-skid, coloured, ceramic tiles 7 to 8 mm thick of size 600 x 600 mm, set and fixing in skirting/ dado or any other vertical surfaces and pointed in white or coloured cement to match and including 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed. 25 Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), ncluding cleaning,removal and disposal of rubbish/ waste materials from premises, complete all as specified and as directed . 26 M&L plain cement concrete in sub bases, floors type B-1, 25 mm thick 1:2:4 (20mm graded aggregate), finishing concrete surface even and fair without using extra cement complete all as specifed and directed 27 M&L Plain cement concrete 1:2:4, type B-1, (using 20mm graded crushed stone aggregate), nominal mix, as in copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work, complete all as specified and as directed . 28 Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm each, complete all as specified. 29 Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exceeding 4.0 Sqm each, complete all as specified. 30 Taking down shutters of any descriptions area exceeding 1.00 Sqm but not exceeding 2.00 Sqm, complete all as specified and directed by Engineer-In-Charge. 31 S & F in repairdoor closer, aluminium extruded body section, hydraulically regulated, designation No-01, universal type, suitable for door shutters up to 700mm in width and of weight not more than 35 kg , complete all as specified and as directed . 32 Mild steel square bar framed work such as in grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; staging for water tanks, cooler stand and similar work conforming to Fe-290, Gde-E-165, including cutting and welding, complete all as specified and as directed . 33 M & L for preparation of old decorated plastered or un plastered surface of walls, making surface even by filling putty in small holes, cavaties, cracks and applying one coat of oil bound distemper (any tint) complete all as specified. 34 Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 125x60mm, complete all as specified and as directed . 35 Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 105x60mm, complete all as specified and as directed . 36 S & F factory made, plain framed, paneled shutter (two panel) 35mm thick, 2nd class hardwood with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and as directed . 37 S & F factory made, glazed and skeleton shutters in second class hardwood, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (in3 panel) with sash bars, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass inclGalvanized mild steel wire cloth, 0.46mm nominal dia of wire and average width of aperture 1.18mmetc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed . 38 S & F factory made steel window, box type, using ERW hollow P section, comprising double frame for and including gauged and glazed skeleton shutter with wire mesh and glass sheet 3.0mm thick, 4mm thick frosted glass jointed internally and made with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs etc, complete all as specified and as shown in drawing No- CEUZ/TD/1517/15, sheet No- 1/3 to 3/3 and as directed by Engineer-In-Charge.Note :- Cost of all items/elements eleborated in the specification and in Drawing shall be deemed to inlcude in quoted rate. 39 S & Fsolid PVC Door Frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplyingand fixing in opening as per specification and drawing, including making good to disturbed surface of walls, complete all as specified. 40 S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/ sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing in SSR, complete all as specified and as directed. 41 Butt hinges, size 100mm, medium weight, cold rolled ISI marked,mild steel, and fixed, complete all as specified and as directed . 42 Aluminium handles, cast type, anodised, size 150mm,ISI marked, complete all as specified and as directed . 43 Aluminium anodised, barrel tower bolts of extruded Section, ISI marked,size 150mm long and fixed, complete all as specified and as directed . 44 Aluminium alloy, anodised, sliding door bolt, size 300mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy,ISI markedand fixed, complete all as specified and as directed . 45 Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 140mm, fixed in floor,ISI marked , fixing in repair, complete all as specified and as directed . 46 Mild steel spring for doors, 300mm, ordinary rat tail rod pattern springs including roller and roller plate,ISI marked , fixing in repair, complete all as specified and as directed . 47 Galvanised mild steel wire cloth, 0.46 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, fixed in repair, complete all as specified and as directed . 48 Preparation of new or previously untreated wood or wooden surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed . 49 Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10cm width or girth including and applying two coats of synthetic enamel paint over one coat of zinc chrome/ red oxide primer, complete all as specified and as directed . 50 Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified. 51 Sheet glass, 3.0mm thick, ordinary quality and glazing with oil putty or with wooden beadings, fixing in square not exceeding 0.50 Sqm in each pane including hacking out old broken glass fo any description, complete all as specified and as directed . 52 Door seal metallic, powder coated, at least 25mm in wide and 1.0mtr in length with nylon fibre brussels, complete all as specified and as directed . 53 Curtain rod,ISI marked, 20mm dia, Chromium Plated mild steel, fancy type inlcuing end knobs, clamps, fixing brackets, stops, round rings to hold the curtain, fixing in repair with wall plugs and screws, complete all as specified and as directed . 54 Taking up or down steel tubing of 15mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed . 55 Tubes, medium grade galvanised, 15mm bore, ISI markedwith all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed.Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates. 56 Old tubes, any grade galvanised, 15mm bore, with all new fittings such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed .Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates. 57 Taking up or down steel tubing of 20mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed . 58 Tubes, medium grade galvanised, 20mm bore, ISI markedwith all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed.Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates. 59 Old tubes, any grade galvanised, 20mm bore, with all new fittings such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed .Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates. 60 S&F in repair PVC (SWR) floor/Nahani trap of 75mm dia outlet, plain with grating including jointing with solvent cement, complete all as specified and as directed . 61 S&F in repair PVC (SWR) P or S trap of 110mm dia outlet,including jointing with solvent cement, complete all as specified and as directed . 62 Vitreous China squatting pan, ‘Orissa’ pattern, size 580x440mm white, with integral foot rests (excluding flushing cistern and flush pipe) but including connection to trap, and to flushing pipe, anti-syphonage pipe, etc including concrete bedding layer complete including making good to dismantled floor in cement concrete M-15 (1:2:4), type B-1 (using 20mm graded crushed stone aggregates), fixing in repair, complete all as specified and as directed . 63 Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32mm dia, waste coupling of PTMT (half or full threaded), fixing in repair, complete all as specified and as directed . 64 Vitreous China wash down water closet pan (pedestal pattern), white (including fixing bolts, flush pipe but excluding flushing cistern) and including plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and making good to dismantled/ damaged floor in cement concrete M-15 (1:2:4), type B-1 (using 20mm graded crushed stone aggregates), fixing in repair, complete all as specified and as directed . 65 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, fixing in repair, complete all as specified and as directed . 66 PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, capacity 10.0 litres and making good to dismantled/ damaged floor/ surfaces, fixing in repair, complete all as specified and as directed . 67 S&F in repair flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern suitablle for IWC, complete all as specified and as directed . 68 Vitreous China urinal,flat back, size of 465x355x265mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern and flush pipe but including of waste pipe), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and union for discharge pipe, fixing in repair, complete all as specified and as directed . 69 S&F in repair PVC connections 15mm size with brass nuts of length 450mm, complete all as specified and as directed . 70 S&F in repairPVC connections 15mm size with brass nuts of length 600mm, complete all as specified and as directed . 71 Bib taps, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repair, complete all as specified and as directed . 72 Bib taps, long body, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repair, complete all as specified and as directed . 73 Bib tap, long body, standard of PTMT any colour high pressure screwed for iron pipe and fixed for 15mm bore pirpe, (Minimum weight 15mm-120gms), fixing in repair, complete all as specified and as directed . 74 Bib tap, Short body, standard of PTMT any colour high pressure screwed for iron pipe and fixed for 15mm bore pirpe, (Minimum weight 15mm-120gms), fixing in repair, complete all as specified and as directed . 75 S&F angle valve/ cock, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repair, complete all as specified and as directed . 76 Stop valves (concealed type), cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore pipe, fixed in repair, complete all as specified and as directed . 77 Stop valves, cast copper alloy,screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 20mm bore pipe, fixed in repair, complete all as specified and as directed . 78 Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15mm bore pipe, fixed in repair, complete all as specified and as directed . 79 S&F Chromium plated shower rose 150mm square size, fancy type, fixed for 15mm bore pipe, fixing in repair, complete all as specified and as directed . 80 S&F in repair waste pipe for SINK/WHB/Urinal for 32/40mm dia all as specified & as directed. 81 S&F in repair Chromium Plated stainless steel towel rail 20mm dia D type 60 cm longbetween flanges fixing in repair, complete all as specified and as directed . 82 Taking down eaves gutters and rain water pipe , soil and waste pipe (any size or pattern ), includding all fittings, heads , shoes bends , swan-necks etc . complete all as specified and as directed . 83 PVC (SWR) pipes, 75mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed . 84 S & F PVC SWR 75mm dia ( pressure not less than 6 kg /cm2)pipes in any length fixed to walls with PVC/MS holder but clamps and conforming to IS-1729 complete all as specified and directed. 85 PVC (SWR) pipes, 110mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed . 86 S & F PVC SWR 110mm dia ( pressure not less than 6 kg /cm2)pipes in any length fixed to walls with PVC/MS holder but clamps and conforming to IS-1729 complete all as specified and directed. 87 S&F in repair waste coupling of PTMT (half or full threaded) for 32mm bore/ 40dia of discharge pipe used for wash hand basin and Sink etc, complete all as specified and as directed . 88 S&F CP Brass Centre hole basin mixture for hot and cold water with round sport without pop up waste system for 15mm bore pipe, fixing in repair, complete all as specified and as directed . 89 S&F Soap dish, fancy type, fixed to plugs with chromium plated brass screws, fixing in repair, complete all as specified and as directed . 90 S&F Glass corner shelf, made with 6 to 8mm thick transparent glass, three teirs including anti rust screws, fixing in repair, complete all as specified and as directed . 91 S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.2 meter long flexible spirochrome flex tube and ABS wall hook including making connections and fixed in repair in position complete in all respect as specified 92 S&F Stainlees steel grating, chromium plated, size 125mm, heavy duty, fixing in repair, complete all as specified and as directed . 93 Sheet glass shelf assembly, consisting 5.50mm thick sheet glass, 120mm wide including anti rust screws, fixing in repair, complete all as specified and as directed . 94 Rotational moulded polyethylene water storage tanks of 1000 liters capacity, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, fixing in repair, complete all as specified and as directed . 95 Rotational moulded polyethylene water storage tanks of 500 liters capacity, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, fixing in repair, complete all as specified and as directed . 96 Disconnecting existing tank, setting aside (or lowering if required) forcleaning, etc. and hoisting if required reconnecting and re-fixing in same position after cleaning of water storage tank capacity 500 Ltrs, mounted on any locations including removal of mud and dirts outside from residential area, including writing date of cleaning on outer surfaces with white synthetic enamel paint, complete all as specified and as directed . 97 Disconnecting existing tank, setting aside (or lowering if required) forcleaning, etc. and hoisting if required reconnecting and re-fixing in same position after cleaning of water storage tank capacity 1000 Ltrs, mounted on any locations including removal of mud and dirts outside from residential area, including writing date of cleaning on outer surfaces with white synthetic enamel paint, complete all as specified and as directed . 98 S&F ball valve/ float valvehigh pressure PTMT with Brass rod& high density plastic ball 20mm dia bore. 99 S&F ball valve/ float valve high pressure PTMT with Brass rod& high density plastic ball 15mm dia bore. 100 M & L for 17/18 mm Medium Density Fibre baord (MDF) with screws to timber frame work such as kitchen cabinet including self drawer, shutter, partitions, etc all as directed. 101 S & F in repair for ball bearing drawer channel 550mm black powder coated for sliding drawers complete all as directed 102 S & Fin repair for magnetic catches for cabinet of size 50mm complete with striking plate and magnetic studd complete all as directed 103 S&F stainless steel peg set of six with base plate and fixed to wall/door with rawal pugs/ s/s screw all as specified and directed.
