Tender For Special Repairs To Bldg No P-59 Of Jco Md Accn Umerd Vihar At Rms-- 1 Dismantling Plain corrugated steel sheeting, any gauge, thickness, including, Nanital or similar pattern roof covering complete all as specified and as directed. 2 Demolition of cement concrete (unreinforced) in ground floors and paving n.exc. 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and as directed. 3 Demolition of unreinforced cement concrete of any description and inany position not otherwise specifically provided for complete all as specified and as directed. 4 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. 5 Taking downchowkats with shutter n.exc 1.5 Sqm each (without taking off shutters from the frame) complete all as specified and as directed 6 Taking down door chowkats with shutter exc 1.5 but not exc 4 sqm each (without taking off shutters from the frame) complete all as specified and as directed 7 S&F in repairs/replacement of 500 ltr capacity rotational moulded polythylene water storage tanks double layer(cylindrical, vertical with closed top ), including 20mm diaBall valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms), all specified in SSR Part-I complete all as specified and as directed. 8 S&F in repairs/replacement of 1000 ltr capacity rotational moulded polythylene water storage tanks double layer(cylindrical, vertical with closed top ), including 20mm diaBall valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms), all specified in SSR Part-I complete all as specified and as directed. 9 Use and waste for formwork to chullah hoods, cha jjas, troughs and similar items including edge complete all as specified and directed. 10 M&L for RCC (Nominal Mix) typeA-1 (1:1 ½:3) (using 20mm graded stone aggregate) as in chajjas etc complete all as specified and directed. 11 M&L for TMT steel bars 10 mm dia and above, as in reinforcement for concrete, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm etc complete all as specified and directed. 12 M&L for cement concrete (1:5:10) type E-2 (using 40mm graded stone aggregate) as in foundation and mass concrete/sunken floors etc complete all as specified and directed. 13 M & L for PCC 25 mm thick type B-0, (1:2:4) (using 12.5 mm graded stone aggregate)as in levelling course of floor complete all as specified and as directed. 14 M&L for light shade/coloured vitrified ceramic tiles (9-10)mm thick (Square / rectangular) of area exceeding 0.18 sqm but not exceeding 0.36 Sqm each, in floors laid over and including 15mm thick screed bedfor laying floor finishes in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles including dismantling of old tiles fromincluding bedding mortar from its position etc complete all as specified and as directed. 15 All as per Ser item No 14.00 (here-in-beofre) but as in skirting, laid over & including 10mm thick baking coat inCM (1:4). 16 M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm,in floors laid over and including 15mm thick screed bedfor laying floor finishes in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles including dismantling of old tiles fromincluding bedding mortar from its position etc complete all as specified and as directed. 17 M&L for Glazed ceramic coloured tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile laid over and including screed bed of 10 mm thick in CM (1:4)including dismantling of old tiles fromincluding bedding mortar from its position etc complete all as specified and as directed. 18 M&L for preparing the sunken floor slab as specified and appying cement plaster coat laid to slope average 20mm thick in CM (1:3) finished even and fair and applying evenly a tack coat of industrial bitumen 85/25 @ the rate of 1.2 kg per sqm etc complete all as specified and directed. 19 M&L for Water proofing treatment by applyingbituminonus primer @ 0.20 kg/sqm providing and laying 3mm thick APP modifide water proofing membrane weighing not less then 3.00 kg/sqm reinforced with non woven polyster mett weighingnot less then 160gm/sqm having soften point not less then 140 degree centi grade, longitudinal tensile strength not less then 650N/Sqm, tearing strength of 180 N, by torch application including minimum 10cm side overlap and 15cm end over lap and over the membrane. 20 M & Lfor APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) and on primed surface including Roughening surfaces of old concrete floor/terrace by picking, chiseling, scraping of surface with wire brush or any other method, sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exceeding 50 m complete all as specified and as directed :- (i) 15mm thick cement plaster in cement mortar 1:4 (ii) Cleaning of plastered roof surface and applying one coat of bituminous primer@ 0.25 litre/Sqm conforming to IS:3384-1986(iii) Applying APP based pre-fabricated with non woven polyester reinforced membrane stabilized with fibre glass strands and top with grey mineral slates 3mm thick and weight not less than 3.00 Kg/Sqm by torch application method.(iv)Applying a coat of solar reflective bituminous aluminium paint @ 0.11Kg/Sqm over mineral surface. 21 M&L for brushing neat cement slurry with 3 kg of cement per square metre complete all as specified and as directed. 22 M&L for 40 mm thick cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in slope correction layer over RCC slab finished without using extra cement complete all as specified and as directed. 23 M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar (1:3) to ends or etc., and making good, cutting not exceeding 10 cm girth etc complete all as specified and as directed. 24 S&F Pressed steel door frames of size 105 X 60mm (Thickness of MS Sheet 1.25mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, including filling of steel chowkhats with Cement concrete (1:3:6), type C-2 (using 40mm graded stone aggregate)including necessary form work complete all as specified and as directed. 25 S&F Pressed steel door frames of size 125 X 60mm (Thickness of MS Sheet 1.25mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,including filling of steel chowkhats with Cement concrete (1:3:6), type C-2 (using 40mm graded stone aggregate)including necessary form work complete all as specified and as directed. 26 S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sidescomplete all as specified and as directed by Engr-in-Charge. 27 S&F 35 mm thick factory made second class hard wood glazed and skeleton shutter, open rebated and prepared to receive glass, gauze etc (without sash bar ) edges of framing plain, camfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part -I section 8 clause 8.42(a) supplied and fitted to chowkat complete all as specified and as directed. 28 Supply and fix stainless stelel wire cloth 0.36 nominal dia of wire and average width apperture 1.40mm and fixed with stainless steel wire staples or wooden beads supplied with shutter complete all as specified and as directed. 29 S&Ffor providing sliding type (3 Track +3 shutter) aluminium windows, section profiles of aluminium as per sketch No SK/2019/01 dated 21/01/19,aluminium alloy extruded sections conforming to HE 9-WP of BIS 733 and HP 9 -WP of BIS 1285 as amended, with minimum thickness of frames (outer bottom, Top & side ) 1.5mm and sliding sash (stiles & rails) of minimum thickness 1.2 mm. The windows shall be procured from a BIS license factory manufactoring windows to BIS-1948, The EPDM gaskets, rollers, recessed handles cum locks aluminium snap beading for receving glass/wiremesh with stainlss steel screws shall b provided with windows complete all as specified and as directed.Note:- Glazing and Stainless steel wire mesh will be paid seperately. 30 S&F Anodised aluminium powder coated ( minimum thickness of powder coationg 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing complete all as specified and as directed. 31 Supply and fix sheet glass selected quality 5.0mm thick, any size, tinted of approved colour fixed with rubber beading complete all as specified and as directed. 32 S&F Aluminium decogrills made out of fixed independently on outside of sliding window system in Aluminium C channelon top & Bottom, weight of aluminium alloy grill shall not be less than 1.5 Kg/m2 complete all as specified and as directed. 33 M&L for Preparing new wooden surface and applying two coats of synthetic enamel paint over a coat of pink wood primer complete all as specified and as directed. 34 M&L for Preparing old wooden surface and applying two coats of synthetic enamel paint over a coat of pink wood primer complete all as specified and as directed. 35 S & F,Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specificationcomplete all as specified and directed. 36 S&F for Factory made solid panel PVC doorshutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and directed. 37 S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. 38 S&F 100 mm thick Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed. 39 S&F Aluminium bow handles, cast type, anodised 150 mm long complete all as specified and directed. 40 S&F Aluminium bow handles, cast type, anodised 125 mm long complete all as specified and directed. 41 S&F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed 42 S&F in repairs 18 mm thick prelaminated Medium density fibre board, Exterior grade, fixed to timber frame-work with stain less steel screws fixed complete all as specified and as directed. 43 S&F 75mm Hasp and staple, safety type, aluminium anodised mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. 44 S&F Continuous (piano) hinges, mild steel bright finish or electro galvanised with flap (when open) 40 mm, fixed with steel screws complete all as specified and directed. 45 S&F 150mm long mild steel ordinary rat tail rod pattern springs including roller and roller complete complete all as specified and directed. 46 Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillars etc complete all as specified and as directed. 47 M&L for brick work with sub class B bricks (using old size burnt bricks) straight or curved on plan exc 6m mean radius built in CM (1:6) including demolition of old brick work complete all as specified and as directed. 48 All as per item 47.00 (here-in-before)but using old bricks retrieved from demolition under item 46 above including cleaning and removal of mortar from old bricks. 49 M&L for brick work with sub class B bricks (using old size burnt bricks) straight or curved on plan exc 6m mean radius in half brick thick wall built in cement mortar (1:4) including demolition of old brick work complete all as specified and as directed. 50 M&L for Rendering 10 mm thickin CM (1:6) on brick work/concrete surfaces finished even and fair without using extra cement including old taking down old plaster complete all as specified and directed. 51 M&L for rendering 15 mm thickin CM 1:4 on brick work/concrete surfaces finished even and fair with WPC @ 2% by weight of cement content and without using extra cement including old taking down old plaster complete all as specified and directed. Note:-WPC will be measured and paid separately. 52 M&L for rendering 5 mm thick cement plaster in CM (1:3) on ceiling finished even and fair including old taking down old plaster complete all as specified and directed. 53 M&L for complete removal of existing treatmentand applying twocoats of oil bounddistemper white or tintedon walls over a coat of alkali resistant primer over 2 mm thick wall care putty(in two layers) complete all as specified and as directed. 54 M&L for preparation of new plastered surfaces of wall applying two coats of OBD white or tintedon walls over a coat of alkali resistant primer over 2 mm thick wall care putty(in two layers) complete all as specified and as directed. 55 M&L for Complete removal of existing treatment and applying 2 coats of oil bound distemper white or tinted over a coat of alkali resistant primer over 2 mm thick wall care putty(in two layers) over ceiling surfaces complete all as specified and as directed. 56 M&L for preparation newely plastered surface and applying two coats of oil bound distemper white or tintedover a coat of alkali resistant primer over 2 mm thick wall care putty(in two layers) over ceiling surfaces complete all as specified and as directed. 57 M&L for preparation of oldwall surfaces by removing the existing treatment completely and applying two coats on external wall of Antifungal exterior emulsion paint over a coat of primer and over 2 mm thick wall care putty(in two layers) complete all as specified and as directed. 58 M&L for preparation of new plastered wall surfaces and applying two coats on external wall of Antifungal exterior emulsion paint over a coat of primer and over 2 mm thick wall care putty(in two layers) complete all as specified and as directed. 59 Taking Down 15 mm steel tubing and connection including cleaning for refixing or removal to store complete all as specified and as directed. 60 Taking Down 20 mm steel tubing and connection including cleaning for refixing or removal to store complete all as specified and as directed. 61 Taking Down 25 mm steel tubing and connection including cleaning for refixing or removal to store complete all as specified and as directed. 62 S&F in repairs Vitreous china wash down water closet pan, (pedestal pattern), white, with and including plastic water closet seat, white, closed pattern with flat bottom, andcover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed. 63 S&F in repair Vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand,brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, complete all as specified and as directed. 64 S&F in repairflushing cistern 10ltr capacity body molded from design quality high impact polly propylene critical, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and 15mm bore 450mm long PVC connection complete all as specified and as directed. 65 S&F CPVC pipes, SDR 11 , 25 mm outer dia conforming to IS - 15778 with all fittings such as Tee, bends ,elbows, unions sockets and end pieces etc to receive the fittings and fixed with solvent concealed in wall , floor and ceiling complete all as specified and as directed. 66 S&F CPVC pipes, SDR 11 , 20 mm outer dia conforming to IS - 15778 with all fittings such as Tee, bends ,elbows, unions sockets and end pieces etc to receive the fittings and fixed with solvent concealed in wall , floor and ceiling complete all as specified and as directed. 67 S&F CPVC pipes, SDR 11 , 40 mm outer dia conforming to IS - 15778 with all fittings such as Tee, bends ,elbows, unions sockets and end pieces etc to receive the fittings and fixed with solvent concealed in wall , floor and ceiling complete all as specified and as directed. 68 S&F in repairs PVC connection low density polythene pipe 15 mm dia , 450 mm long , heavy duty with PTMT nuts complete all as specified and as directed. 69 S&F in repairs Pillar tap with aerator, cast copper alloy with capstain heads, chromium plated, fancy type, screwed down with high pressure, with or without lettered Hot or Cold with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore dia of pipe complete all as specified and as directed. Make : Cera Cat No QT F2006101 or equivalent in Hindware/Parryware. 70 S&F in repairs 15 mm bore Bib cock with wall flange and aerator,brass chromium plated with fancy type and screwed down to 15mm bore GI tubing or for brass ferule complete all as specified and as directed.. Make : Cera Cat No. QT F2006151 or equivalent in Hindware/ Parryware. 71 S&F in repairs 15 mm bore two way Bib cock with wall flange and aerator,brass chromium plated with fancy type and screwed down to 15mm bore GI tubing or for brass ferulecomplete all as specified and as directed. Make : Cera Cat No. QT F2006151 or equivalent in Hindware/ Parryware. 72 S&F in repairs Angle stop valve with wall flange 15 mm bore of pipe brass chromium plated, screwed down, high pressure screwed both ends for iron pipe for unions and fixed complete all as specified and as directed. 73 S&F in repairs Brass chromium plated toilet paper holderall as specified and as directed Make : 74 S&F in repairs Stainless steel soap dish white of size 160 x 160 x 90 mm as approved fixed with brass screws or embedded in wall completeall as specified and as directed. 75 S&F in repairs Health faucet of brass body with wall hook and 1mtr flexible stainless steel braided rubber hose pipe fixed in repaircompleteall as specified and as directed. Make:- Cera Cat part No F 8030102 or equivalent as per make oflist attached. 76 S&F in repairs Towel rail chromium plated fancy type 60cm long including bracket fixed between flanges complete complete all as specified and as directed. 77 S&F in repairs Brass chromium plated over head 15 mm boreshower rose 120mm diawith 3 flow swivel jointincluding shower arm fixing to steel pipe or union including taking down old shower rose completeall as specified and as directed. 78 S&F in repairs Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixedcompleteall as specified and as directed. 79 S&F in repairs 600 X 450mm bevelled edgemirror of selected quality glass, mounted on 6mm thick AC building board fixed to wooden plugs withCP brass screws and cup washers completeall as specified and as directed. 80 Supply only Integral Water Proofing (liquid) Compound completeall as specified and as directed. 81 S&F PVC (SWR) pipes of dia110mm boredouble socketed in any lengthwith rubber ring joints fiexed to walls completeall as specified and as directed. 82 S&F PVC (SWR) pipe of75 mm bore in double socketed in any lengthwith rubber ringjoints fixed to walls completeall as specified and as directed. 83 S&F PVC Nahani traps 75 mm outlet with stainless steel cover grating completeall as specified and as directed. 84 S&F PVC (SWR)bends of 75mmbore in radius completeall as specified and as directed. 85 S&F PVC (SWR)bends of 110 mmbore in radius completeall as specified and as directed. 86 S&Ffor Steel work in MStublartrusses, MS Square Tube ,Purlin,rafter including special shaped washeretc complete using ERW or indication butt welded tubes confirming to I.S 1161-1998 gradeSt-240 completeall as specified and as directed. 87 S&Ffor Joist,channel ,angle,or tee sections,fixed independently, without connecting plates ,etc (cut to ordinary length ie within 20mm of the length indicated Fe -410-W(Gde-E-250 qaulity-B) completeall as specified and as directed. 88 S&F Plates (plain or chequered) channels,square cut or notched (ordinary and counter shunkforming holes,without any attachement completeall as specified and as directed. 89 S&F Wind ties for roof includingsecuring bolts ,posts and struts including all necessary drilling bolt or riveting etc. and similar work confirming to FE-290 Gde-165 completeall as specified and as directed. 90 S&F Pre-paintedgalvalume aluminium zinc coating GI based trapezoidal profile steel sheet 0.50mm (TCT) an colour having tensile strength of 550 Mpa as in roofcovering/claddingto wall,fixed with selftapping screws including dismantling of old sheets from its position completeall as specified and as directed. 91 S&F Pre-paintedgalvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick on ridge an colour having tensile strength of 550 Mpa as in roofcovering/claddingto wall,fixed with selftapping screws including dismantling of old sheets from its position completeall as specified and as directed. 92 M&L for preparation of two coats of synthetic enamel paint over a coat of red oxide,zinc chrome primer on newly prepared steel surface of any description,over 10cm width or girth,not other wise describedcompleteall as specified and as directed. 93 M&L for preparation of two coats of synthetic enamel paint over a coat of red oxide,zinc chrome primer on newly prepared steel surface of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint, completeall as specified and as directed. 94 S&F 0.56mm Aluminium corrugated sheeting Alloy 31000 H4, STUCCO Embossed finish with two corrugations side lap fixed with coach screw and Aluminium washer in roof and wall etc. with end laps stitched with 25x6mm G.I. bolts at 20cm apart including dismantling of old sheets from its position completeall as specified and as directed. 95 S&F 16 to 20mm dia Mild steel screws bolts(Machine made)withhexagonalor square heads at one end and screwed both ends ,each screwed end to be fitted with washers and one hexagonal or square nut,length of bolt exc 10cm and n.exc 15cm long. with washers completeall as specified and as directed. 96 M&L for Preparation ofold painted surfaces of steel & Iron of any description over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) completeall as specified and as directed. 97 S&F in repairs 20 mm dia powder coated aluminium curtain railsfixing with fancy brackets and closing caps completeall as specified and as directed. 98 M&L for chequered cement concrete tiles of size not less than 300x300x25mm thick laid over and including 15mm thick screed bedfor laying floor finishes in cement mortar (1:6) etc, set, jointed and pointed in neat cement slurry with grey cement and pigments complete all as specified and as directed. 99 S&F in repairs 1mm thick stainless steel sink, plugs, washers, PVC waste pipe, union, CP coupling & cantilever brackets embedded in cement and sand mortar in wall , ovesinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mmrall size of sink 495mmx420mm, bowl size 410mmx330mmx 160 mm as in repair complete all as specified and as directed. 100 S&F in repairs stainless steelplate rack of standard pattern & of size 790x610x220mm thickness of stainless steel sheet shall be304 AISI including fixing to wall with 4 nos 50 mm screws & pvc rawl plugs complete all as specifed and as directed. 101 S & F for4 mm thick of size 600x600mmHSPC (high pressure Steam Cured) non asbestos fibre cement reinforced multipurpose board, pre-primetered self embossed, textured designer boardE-Board Classic fixed or laid/inserted to timber/ GI frame work with screws to be fixed in ceiling flat or sloping and Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre both ways, size of grid 605 x 605mm fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any sizeincluding dismantling of old unsv ceiling boards (fibre, pulp, insulation, etc.) any thickness including cover fillets of any description and at any location complete all as specified and as directed. 102 S & F for4 mm thick of size 600x600mmHSPC (high pressure Steam Cured) non asbestos fibre cement reinforced multipurpose board, pre-primetered self embossed, textured designer boardE-Board Classic fixed or laid/inserted to timber/ GI frame work with screws to be fixed in ceiling flat or sloping and Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre both ways, size of grid 605 x 605mm fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any sizecomplete all as specified and as directed. 103 M&L for cement concrete type B-1 (1:2:4) (using 20 mm graded stone aggregate) as in surface channels and drains complete all as specified and as directed. 104 M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms mouldscomplete all as specified and as directed. 105 M&L for Machine cut kota stone slab flooring 20-25 mm thick over 20 mm cement screed base in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing polishingand rounded or chamfered for nosing complete all as specified and as directed. 106 M&L for Machine cut kota stone (20-25)mm thickin riser of steps, skirting, dadoand pillar over 15 mm thick screed in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing polishingand rounded or chamfered for nosing complete all as specified and as directed. 107 M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, laid over and including 20mm thick screed bed/bedding layer in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. 108 M&L for 100mm thick Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed. 109 M&Lformachine pressed precast concrete interlocking paver block of any colour any shape and size confirming to IS 15658-2006 of rubber moulded 80mm thickness, M-40 grade with grey cement and pigment laid over and including 25mm thick sand filling under floors or in foundation including watering and consolidation complete all as specified and as directed. 110 M&L for Cutting holes in brick walls exceeding half bricks but not exceeding one brick built in cement mortar or cement lime mortar and stone walls built in lime mortar complete all as specified and as directed. 111 M & L 25mm thick second class hard wood boarding , plained one side with butt joints as ineaves boards complete all as specified and as directed. 112 M&L for 75 mm thick PCC (1:3:6) type C-2 , (using 40 mm graded stone aggregate) in plinth protection/aprons/path laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide tha area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and as directed. 113 Material and labour for (concelaed Type) point wiring in repairs including necessary chases cutting of wall for one light/fan/call bell point with 1.5 sqmmPVC insulated (FR-LSH) PVC sheathed multistranded copper conductor cable 1100 volts gradecontrolled by one way switchincluding 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC conduit with all accessoriesand sunk GI box for mounting of fittings like switch, socket and fan regulator etc and making good the distrubed surfaces as per the existing complete all as specified and as directed by the Engr-in-Charge 114 Onelight pointcontrolled by one, one way switch . 115 One Ceiling fan/ exhaust fan point controlled by one, one wayswitch. 116 One 3 pin socket outlet 5 Amps on the same board with other switches. 117 One 3 pin socket outlet 5 Amps on the Independent board. 118 One bell pointcontrolled by one, one way switch . 119 One light point control by two way switch 120 All as per item No- 113.00 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed. 121 S&F Switch Piano, flush type single pole, one way 5 Amps complete all as specified and as directed. 122 S&F Socket outlet, 2 in 1, 5 pin 5A flush type complete all as specified and as directed. 123 S&F Switch Socket combination, 2 in 1, 5 pin 6A flush type complete all as specified and as directed. 124 S&F Switch Socket combination, 2 in 1, 5 pin 6A/16A flush type complete all as specified and as directed. 125 S&F for bell push switch 5 amps piano type flush type complete all as specified and as directed. 126 S&F bell AC 230 volts musical type complete all as specified and as directed. 127 S&F Switch piano, flush type single pole,two way 6 Amp complete all as specified and as directed. 128 S&F stepped type electronic fan regulator 100/120 Watt socket size flush type on the existing phenolic laminated sheet complete all as specified and as directed. 129 Taking down existing burnt aluminium/ copper sub main wiring and M&L for sub main wiring with two runs of 4.0 Sq mm and one run of 4.0 Sq mm for earth wire with multi standard copper conductors FRLSH quality, 1100 volts grade, drawn throughand including non metalic rigid PVC conduit with all conduit accessories (including concealing and making good to the disturbed surfaces of walls, ceiling,floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete all as specified and as directed. NOTE:- Two runs of 4.0 Sq mm + one run of 4.0 Sq mm and one run of PVC Conduit and its accessories of suitable size shall be measured as one unit length. 130 S&F in repairs LED Light fitting 1 x 20 watt (4 Ft), Wall/ Surface mounted, intergrated type with all accessories internally prewired and incl connecting up with, including two Nos PVC blocks and connecting upwith flexible copper cable of size 0.75 Sq mm 3 core and flexible pipe from ceiling rose to the light fitting complete all as specified and as directed. 131 S&F in repairs 10W LED, 2, Wall mountedpolycarbonate batten internally pre-wired with electronic driver and polycarbonate diffuser and fixing the same onand including two Nos PVC blocks and connecting upwith flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting complete all as specified and as directed. 132 S&F in repairs/replacement for decorative wall mounted light fitting made up of polycarbonate including 9 watt LED lampwith B-22 basecomplete all as specified and as directed. 133 S&F ceiling rose 3 terminal PVC/Polycarbonate isolated body complete all as specified and directed. 134 S&F in repairs Bldg Security LED 1x25W light fitting, drawn through including GI bracket of 25mm borelight grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling holesas required and connecting upwith flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fittingcomplete all as specified and as directed. 135 Supply and fixingBed side light 3Watt LED light reading in bed just got easier with this colletion of adjustable LED bedside lights complete all as specified and as directed. Make : Philips Cat Part No48042/Bajaj/Havells 136 S&F in repairs VTPN DPX 4 way,double door 415 Volts, 50 Hz, IP 43 IK 09 sheet steel, powder painted, with02 neutral link & 02 earth bar and cable ties for cable managementsuitablefor fixing ofMCCB asincomer and MCB SP/TP as outgoing MCB DBs incl taking down of old UNSV DBs and making good the disturbed surfaces to match with existing specification , complete all as specified and as directed.Note : MCBs will be measured sepeartely. 137 S&F in repairs MCCB 4 Pole, 415 V, Adjustable type, 100 Amps with breaking capacity 16 KA complete all as specified and as directed. 138 S&F in repairs MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacityincluding taking down old unsv DB and making good the disturbed surfaces to match with existing specification , complete all as specified and as directed.Note : MCBs will be measured sepeartely. 139 M&L for metal clad AC socket point single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP 32 Amps etc complete all as specified and as directed. 140 S&F in repairs MCB SPN 32 Amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning MCB DBcomplete all as specified and as directed. 141 S&F in repairs MCB SP 6 to 32 Amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning MCB DBcomplete all as specified and as directed. 142 S&F in repairsexhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m complete all as specified and directed. Note : Old Exhaust Fan deposted EM store yard. 143 S&F in repairsexhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed.Note : Old Exhaust Fan deposted EM store yard. 144 Taking down and M&L for overhauling/ servicing of ceiling fan of any size / sweep (i.e 1200/1400mm sweep) and make comprising dismantaling, cleaning internally and externally and cleaning / lubricating of bearing / bushes using fresh lubricant (Oil grease) re-assembling, checking of split pin, hook assembly & hanging andincluding provision of cable fromceiling rose or connector to fan and testing for proper functioning complete all as specified and as directed. 145 S&F in repairsceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service valuenot less than 5.1 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed. Note : Old Exhaust Fan deposted EM store yard. 146 Supply, Fixing and testing of vertical type wall mounted storage water heater of Capacity 25 Ltrs BEE 5 Star rated or minimum Standing Loss of 0.511 kWh , 240V, 50Hz with Maximum power consumption of 2KW , dry powder fero glass line coating technologyfor inner tank with incoloy heating elementwith minimum4 years warranty , ABS outer body , 2 units of PVC connection pipe with length of 450mm length for hot and cold water supply with complete Accessories complete all as specified and as directed. 147 Supply, installation, testing and commissioning of factory made meter panel board wall mounted made out of CRCA sheet of 1.6mm thick indoor type totally enclosed weather proof, dust vermin proof with front openable, hinged door locking arrangement mounted on MS clamp welded to panel body duly grouted in wall including provn of Acrlylic sheet for meter reading, space for refixing of single phase smart meter 5-60 Amps 04 Nos AC 230 Volts incl lugs, spacer mounting chanels, rubber gasket, locking knobs, PVC shrinkable sleeves, nut bolts, washers etc, suitable compartment of every meter and control MCB circuit and epoxy powder coated spray paint with primer, suitable arrarments for incoming MCCB and outgoings with copper bus bar and terimal links, CPRI type tested complete all as directed by Engr-In -Charge.Outgoing (a) MCB SPN 40-63 Amps, 230 volts 10 KA C Curve - 04 Nos and MCB SP 6-32 Amps -02 Nos (b) Refixing existing smart meters - 04 Nos ( Note : to be insured properly maching the qtr Nos before fixing the smart meters) 148 Taking down burnt unsv LT UG cable of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of35 sq mm, 3.5 core complete all as specified and as directed.NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items. 149 Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft/ loose soil complete all as specified ans as directed. 150 Returning filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm thick all complete all as specified ans as directed. 151 Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all complete all as specified ans as directed. 152 M&L for spread fine river sand in trenches complete all as specified ans as directed. Note: Punned thickness shall be measured and paid. 153 Supply & laying tubes light grade galvanised, with all fittings, fixed complete to walls, poles, ceilings or laid in floors/ trenches/ road crossing for protection of cables of size 40 mm dia bore including taking down corroded GI tubing complete all as specified and as directed. 154 M&L for laying brick sub class B old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed 155 Supply and laying tubes Medium grade galvanised GI tubing with all fittings, fixed complete to walls/poles/laid in floors/trenchs/road crossing of size 25mm dia bore including complete all as specified and as directed. 156 S&F Stop valves 25mm, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed all as per specified and as directed. 157 M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed. NOTE:- (i)The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber, CI cover 10 mm thick, funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 441 of MES SSRPart-II. (ii)Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately.
