Tender For Purchase Of Equipment For Open Gym Ward-31(Balance)(Rate Quating Should Be Include Gst), Ernakulam-Kerala

Tender For Purchase Of Equipment For Open Gym Ward-31(Balance)(Rate Quating Should Be Include Gst)=-Leg Press (Double) -Supply and Installation of Double Leg Press having the following specifications: Dimensions: (L X W X H) = 1676 x 400 x1500 mm. Main frame - Ø 114 mm OD “B” class GI pipe. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Foundations cover cap - dome shape of PP/NYLON/HDPE material. Link - is Ø 60 mm OD “B” Class GI pipe. Seat frame - Ø 42 mm OD “B” Class GI pipe. Leg Press back rest should be angled in 120-130 degree. Foot rest-cast iron 124 x 296 x 5 mm thick and M.S plate of 2 mm thick use to support it. Seat & back rest – 380 x 275 x 60 mm thick high-density polyethylene (HDPE) blow molded with M10 in-sert wall thickness 3 to 4 mm. Link connected with frame by 8 mm thick laser cutting MS profile. Top Closing cap – dome shape made by PP/ NYLON/HDPE material. Closing cap’s- PP/ NYLON/HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing- use is 6005 permanent lubricated reputed brand. Pin– Ø 25 mm M.S. bright bar pin. Bearing bushes - Ø 60 mm OD seamless pipe. Circlip– A 24 circlips are used for assembly. Coating - best quality of powder coating 80-120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing.<br> 3 SIT UP BOARD made from C Class GI pipe to be use by two persons at one time. Closing Caps are made up of Low Linear Density Poly-Ethylene (LLDPE) Material with Injection Moulding. The powder coat should be Poly urethane & Epoxy powder with 60 to 70micron thickness. Dimensions: 2000mm (Length) x 1100mm (Width) x 650mm (Height). 4 Cross Trainer (Double) - Supply and Installation of Double Cross Trainer having the following specifications: Dimensions: (L X W X H) 2280 x 550 x 1650 mm. Main frame- Made of Ø 88 mm OD “B” class Gl pipe dually bending design. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Paddle vertical support - Ø 42 mm OD “B” Class Gl pipe. Handle - Ø 33 mm OD “B” Class Gl pipe dually bending design. Leg movement frame – 50 mm x 50 mm x 2 mm thick square pipe. Footrest - cast iron 124 x 296 x 5 mm thick and M.S. plate of 2 mm thick use for to support it. Top Closing cap – dome shape made by PP / NYLON / HDPE material. Closingcap’s– PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD B class G.I. pipe. and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Grips - High quality rubber. Bearing- Use is 6005 permanent lubricated reputed brand. Bearing bushes - Ø 60mm OD seamless pipe. Pin – Made of Ø 25mm M.S. bright bar. Circlips – A 24 circlips are used for assembly. Coating - best quality of powder coating 80-100 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. 5 CYCLE : Providing and fixing Cycle - FPSPCL208 (Make FUN PLAY ) using , 25NB & 40NB GI B-Class Pipe for MAIN FRAME , 32 NB GI B-CLASS pipe for SEAT FRAME , 25NB GI B-CLASS Pipe for HANDLE FRAME , Nylon 66 injection moulded BEARING CAP & PIPE CAP , fully Done by first coat of primer - jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70-80 micron thickness POWDER COAT including cost of concrete foundation , all materials,labour, etc all complete asper the instruction of Engineer in charge

INR 555 /-

INR 1.38 Lakhs /-

FileName	File Description	File Size
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB