Tender For Lab Construction Work - DismentlingExisting damage PlasterIncluding disposal of refuse as directed by E/IC with in a distance of 60 meters etc. all complete. {Chapter No. 17 S.I. No.16 (706)} 2 Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. (17-Chapter SI.No.16) 3 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc complete and stacking within 50 metres lead Of area 3 sq. metres and below. (17-Chapter Si. No.8) 4 Earth work in Excavation in foundation in ordinary soil (loam, clay or sand) including, lift up to 1.50 m and lead up to 30m and including filling watering and ramming of excavated the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer-in-charge up to a distance of 30 M form the foundation trenches. (Rate including Royalty of earth also) (4-Chapter Si.No.1) 5 Cartage of Malva, Silt, sludge kankar and other disposable organic material etc. all complete with labour T&P including cartage of 8 km. (Chapter No.3 Si.No.8) 6 Providing and laying Cement Concrete in 1:5:10 (1 cement :5 fine sand 10 Stone ballast 40 mm gauges) and curing complete, including cost of form work in foundation and floors. (5-Chapter Sr.No.1) 7 Class-150 Brick Work in 1:4 Cement and Coarse Sand, mortar in foundation and plinth including supply of all materials, laborand tools and plants, etc. Required for proper completion of the work. ( Chapter No. 06 Sr.No. 2) 8 Class-150 brick work in 1:4 cement and coarse sand, mortar in Super Structrure including supply of all materials, laborand tools and plants, etc. Required for proper completion of the work. ( Chapte No. 06 S.I. No. 2+5) 9 12mm thick cement plaster in single coat of fair side of single of half brick wall forinterior plastering up to floor two level including internal rounded angles chamfers and rounded angles not excluding 80mm in girth and finished even and smooth. No extra for mixing any additive.(c) 1 Cement : 4 Coarse sand.(Chapter No.13 Si.No.1) 10 Providing and laying Cement Concrete in 1:2:4 of not less than strength of M-15 stone grit (20 mm nominal size) approved coarse sand and cement. Curing complete including of cost of form work in foundation and floors.(5-Chapter Sr.No.6 Si.No..4.1.3) 11 R.C.C work with cement approved coarse sand and 2cm (3/4) gauge approved stone ballast in the proportion 1:2:4 (One Part of Cement, Two Part of Coarse Sand and Four Part of 2cm Stone Grit) in heavier beam I.e. having span more than 6 meters excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 bwgi binding wire and including necessary centring and shuttering etc. And also including supply of all materials labor and tools and plants etc. Required for proper completion of the work. Strength of the concrete shall not be less than m-150.(5-Chapter PWD SCH.No.286) 12 R.c.c work with cement approved coarse sand and 2cm (3/4) gauge approved stone ballast in the proportion 1:2:4 in R.C.C Slab excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 bwgi binding wire and including necessary centring and shuttering etc. And also including supply of all materials labor and tools and plants etc. Required for proper completion of the work. Strength of the concrete shall not be less than M-150.(5-Chapter Si.No.8) 13 Mild steel or iron in plain work such as reinforced concrete or reinforced brick work (when not included in and an overall rates) brought for proper completion of the work and including supply of steel, its wastage bend hooks and authorized over lapping shall be measured up to floor two level. (b) 10mm to 12mm tor.(Chapter No. 10 As per M.R.) 14 Mild Steel work in built up tubular ( round, square or rectanglar hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying priming coat of approved steel perimer, including welding and bolted with special shaped washers etc. complete. (Chapter No.10 Si.No.1) 15 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed wit polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1mm thick with zinc coting not less then 275 gm/sqm (Chapter No.11 Sr.No.3(i) New) 16 Providing and Fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & Cold Water Supply, including all CPVC Plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing, This includes Jointing of pipes & fittings, with one step CPVC solvent cement and testing of joints, complete as per direction of Engineer-in-Charge. (D) 32mm nominal outer dia pipes.(Chapter No.23 SI.No.7D) 17 Providing and Fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & Cold Water Supply, including all CPVC Plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing, This includes Jointing of pipes & fittings, with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. (Internal work)(A)15mm nominal outer dia pipes. (Chapter No.23 Si.No.8A) 18 Providing and Fixing PVC pipe conforming to ISI make working pressure 6 kg/Cm including testing labour T&P etc. all complete.110mm diameter. (Chapter No.23 SI.No. 30(iii)) 19 Providing and Fixing PVC pipe conforming to ISI make working pressure 6 kg/Cm including testing labour T&P etc. all complete.140mm diameter. (Chapter No.23 SI.No. 30(iv)) 20 Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100mm Sand Cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the wall and floors wherever required : White Vitreous China Orissa pattern W.C. pan of size 580x440 mm with with integral type foot rests. (Chapter No.24 SI. No.1) 21 Providing and fixing water closet squatting pan (European type W.C. pan) with 100mm Sand Cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the wall and floors wherever required : White Vitreous China Orissa pattern W.C. pan of size 580x440 mm with with integral type foot rests. (Chapter No.24 SI. No.2) 22 Providing and fixing wash basin with C.l. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever require: (White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C. P. brass pillar taps) {Chapter No.24 Si.No.5A} 23 Providing and fixing C.P. brass bick cock fo approved quality confirming to IS:8931. 15mm nominal bore. (Chapter No.23 Si.No.19a) 24 Providing and fixing C.P. brass stop cock (concealed of standard design and of approved make conforming to IS:8931.15mm Nominal bore. (Chapter No.23 Si.No.22) 25 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350mm with white PVC automatic flushing cistern, with fittings, standared size C.P. brass flush pipe, spreaders with union and clamps (all in C.P. brass) with waste fitting as per IS: 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fitting and cutting and making good thg walls and floors whereever required: Single half stall urinal with 5 litre PVC. Automatic flushing cistern. (Chapter No.24 Si.No.6A) 26 Providlng and laying Polished Granite Jet Black stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admi)ied with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.{Chapter No.14 Si.No.27} 27 Providing and Laying Vitrified Tiles 600x600mm Size(thickness 10mm), with water absorption less than 0.08% and conforming to IS:15622, of approved brand manufacture, in desired colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, including grouting of joints etc. all complete. (Chapter No.14 Sr.No.21) 28 Kota stone slab flooring over 20 mm (average) thick base laid over and joined with gray cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement: 4 coarse sand) :25 mm thick. (Chapter No.14 Si.No.12-11.26.1) 29 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. including curing the cost of all material, labour, T&P etc. complete. (Chapter No.15 Si.No.1) 30 Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 Itr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) supply of all labour material and T&P required for proper completion of work. (Chapter No.15 Si.No.5) 31 Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement: 2 stone dust) with an admixture of pigment matching the stone shade: (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) Red sand stone - exposed face fine dressed with rough backing. 30 mm thick (Chapter No.18 Si.No.7) 32 Providing and fixing Red Sand stone jali 40 mm thick throughout in cement mortar 1:3 (1 cement: 3 coarse sand), including pointing in white cement mortar 1:2 (1white cement: 2 stone dust) with an admixture of pigment,matching the stone shade, jali slab without any chamfers etc. (Chapter No.18 Si.No.4) 33 Pro/iding and fxing lSl marked flush door shutters conforming to lS : 2202 (Part l) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.including ISI marked Stainless Steel butt hinges with necessary screws. (A) 35mm Thick. (Excluding cost of Flttings) (Chapter No.9 Si.No.1-9.21.1) 34 Fixing Door chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15x10x10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in- Charge. (Chapter No.9 Si.No.7a-14.2.1) 35 Fixing Window chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15x10x10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in- Charge. (Chapter No.9 Si.No.7b-14.2.2) 36 Providing & fixing Glazing in Aluminum Doors, Window, Ventilators Shutter and Partition etc.. With EPDM rubber/neoprene gasket etc. Complete as per (Cost of aluminum snap beading shall be paid in basic item) : (iii) with float panes of 8.0mm thickness. 37 Veneered flat pressed three layer or graded wood particle board with commercial veneering on both sides conforming to lS:3097, grade I 12mm thick particle board as per direction given by Engineer in Charge. (Chapter No.12 Si.No.1) 38 Providing and lixing in wall lining medium density fibre board lS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. (Chapter No.12 Si.No.5-b) 39 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/ sqm, both side inclusive) consisting of main T runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross T of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main T at 600 mm center to center to form a grid of 1200x600 mm and secondary cross T of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel lo form grids of 600x600 mm and wall anGIe of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, Iight fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T- sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in plain Tegular edge GIobal white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. (Chapter No.12 Si.No.10) 40 Providing and fixing 12 mm thick Panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Marine plywood conforming to IS: 710 (Chapter No.12 Si.No.9) 41 Retro Reflectorised Signs (Stainless steel Frame and Post with one side sings) Supply & foxing of reflective sign board (Single side) of size 1.50x1.20 m retro reflective sheeting of HIP grade type-IV, the board shall be fixed on 50mm SS 304 grade pipe and reflective sheet on 4 mm thick, ACM sheet of standard make as per MORTH specificaton. The Board shall be fixed using 2 man post 45x45x60 cm cement concrete foundation. The stainless steel joint welding of SS pipe work shall be band and grinder property including buffing so an to give uniform shining at weded Joints. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrink age, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory! Institute by the manufacturer of the sheeting and In case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad Alternatively. a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathenng requirements from a reputed laboratory In India can be accepted provisionally. In such a situation, the Employer / Client, if so desires. could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67.2012. Legends, letters, numerals and borders etc should be as per MORTH specification No-801.3.7. Proof of the same in form of government report shall be uploaded while quoting tender. (Chapter No.28 Si.No.25) 42 Providing & Supplying 2 Tone Air Conditioner ISI Mark etc all complete. (As per Market Rate) 43 Supply & Providing Water Purifire (R.O.Plant) etc all complete. (As per Market Rate) 44 Cost of Septic Tank.(As per Detail Attached) 45 Supply and Fixing of Light Fitting Switch Board. (None Sheduled) 46 Supply and Fixing Wiring of Light Point. (None Sheduled) 47 S/L/J of 20mm dia PVC Cunduct Pipe etc. all complete. 48 Supply & Fixing of wiring Sub Main. 49 Supply & Fixing of Plug Point 15Amp. 50 Supply & Fixing of 27watt. CFL etc. all complete. 51 Lettering & Painting of wall etc. all complete. 52 Supply & Fixing 1000 Ltr P.V.C. Sintex Water Storage Tank Syntax or equivalent etc. all complete. (None Scheduled) 53 Constructing brick masonary chamber for underground C.I. inspection chamber and bends with bricks in cementmortar 1:4 (1 Cement : 4 Coarse Sand) C.I. cover with frame (light duty) 455x610mm Internal dimensions, total weight of cover with frame to be not less than 38kg (weight of cover 23kg and weight of frame 15kg), R.C.C. top slat with 1:2:4 mix (1 Cement : 2 Coarse Sand : 4 graded stone aggregate 20mm nominal size), foundation concrete 1 :5:10 (1 Cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortal 1:3 (1 Cement : 3 Coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard desing: (a) Inside dimensions 455x610mm and 45cm deep for single pipe line : With Common burnt clay F.P.S. (non modular) bricks of class designation M-150). {Chapter No.25 Si.No.8a) 54 Constructing brick massonry chamber for underground C.I. inspection chamber and bends with bricks in cementmortar 1:4 (1 Cement : 4 Coarse Sand) C.I. cover with frame (light duty) 600x850mm Internal dimensions, total weight of cover with frame to be not less than 38kg (weight of cover 23kg and weight of frame 15kg), R.C.C. top slat with 1:2:4 mix (1 Cement : 2 Coarse Sand : 4 graded stone aggregate 20mm nominal size), foundation concrete 1 :5:10 (1 Cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortal 1:3 (1 Cement : 3 Coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard desing: (c) Inside dimensions 600x850mm and 45cm deep for pipe line with three or more inlets : With Common burnt clay F.P.S. (non modular) bricks of class designation M-150). {Chapter No.25 Si.No.8c) 55 Making connection of drain of sewer line with existing man hole including breaking into and making good the walls, floors with cement concrete 1:2:4 cement plastered on both side with cement mortar 1:3 finished with a floating coat of neat cement and making necessary channels with cement concrete 1:2:4 for the drain etc. all complete. (Chapter No.25 Si.No.9) 56 Supply and Fixing Stainless steel (Grade 304) ralling made of Hollow tubes, channels, plates etc.Including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary steel nuts and bolts complete. I/C fixing the ralling with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts fasteners etc.). (Chapter No.10 SI. No.19) 57 Supply and fixing of exhaust Fan etc all complete. (As per Market Rate) 58 Supply & Fixing 1200mm Fan Bajaj/Crompton make etc. all complete. (Market Rate None Scheduled) 59 Supply Fixing Fan Box etc. all complete. (None Shceduled) Market Rate. 60 Supply and burring of safe earthing electrode T-19 Zn-Zinc coated, length 2000mm, outer pipe 48.4mm x 3.2mm, inner pipe 26.9mm x 2.6, terminal dia 12 mm coating 80-100 micronfilled with Crystalline Conductive Mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonary housing. (From electrode terminal to switch board, cost of 25x3 G.I. strip will be extra) Make: as approved in UPPWD & CPRI certified. 61 Supply & Fixing Granite Stone Work Display Board (Size 2.50ft x 4.00ft) including Painting, Lettering etc. all complete. (None Schedule) 62 Sub Total 63 Add/Deduction Rs. For Estimate Figure Amount Match 64 Grand Total
