Tender For Certain B And R Repairs Repair To Roof Treatment And Roof Sheets Of Otm Accn At Suranussi Under Age I Suranussi; 1 Demolition of brick work built in cement mortarincluding all quoins arches, pillars etc but including ashalr facing dressed stone work and precast concrete articles complete all as specified and directed 2 Demolition of cement concrete in ground floor and pavings not exceeding 15 cm thick above or below ground level,complete, all as specified & directed. 3 Taking down cement or cement lime plaster of any description on brick or stone walls, etcincl raking out joints hacking for keys srubbing down with water etc complete all as specified anddirected 4 Taking down chowkats or frames with Shutters( without taking off the shutter from the frame ) of area n.exc 1.50 Sqm each and removing from site complete all as specified anddirected 5 Taking down chowkats or frames with Shutters( without taking off the shutter from the frame ) of area exc 1.50 Sqm but n.exc 4.00 Sqm & removing from site complete all as specified anddirected 6 Taking down shutters of any description exceeding 1sqm each and not exceeding 2.00 sqm each complete all as specified anddirected 7 Taking down shutters of any descriptionsize exceeding 1 sqm and n.exc 2 sqm but refixing in the same opening complete all as specified anddirected 8 M&Lfor brick work , with sub class B bricks built in cement mortar 1:6 straight or curved on plan exc 6mtr mean radius, using old size bricks complete all as specified & directed. 9 M&L for 15mm thick cement plastering in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement complete all as specified & directed. 10 M&L 15 mm thick cement plastering in cement mortar (1:4) of brick work or concrete surfaces with using water proofing compound @ 3% by weight of cement or as per manufactures instructionfinished even & smooth without using extra cement complete all as specified. 11 M&l for 5 mm thickrendering in cement mortar in 1:3 on ceiling complete all as specified and as directed 12 Dismantling wall andCeiling boards any thickness, including cover fillets complete all as specified and as directed. 13 M&L for 12mm thick perforated particle board/tiles for insulation and accoustic purpose 60X60CM in size fixedin frame work /grid complete all as specified and as directed. 14 M & L forGl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, complete all as specified and directed. 15 Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete, all specified and directed. 16 S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall , fixed withJ-type hook complete all as specified anddirected 17 S&F Pre-painted galvalume aluminum zinc coating GI based plain sheet ,sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall , fixed withJ-type hook complete all as specified anddirected. 18 S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering to Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to GdeFe 290(Gde E-165) complete all as specified anddirected 19 S&F 2nd claasshard wood 35mm thickfactory made Glazed andskeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars),edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified inSSR Part I, Section 8, clause 8.24(a); supplied and fitted to chowkats 20 S&F solid PVC door frame of size 50mmX 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing complete all as specified anddirected . 21 S&F 30mm thick factory made PVC door shutter solid panel consisting of frame made out of MS tubes for top & bottom rails .Ms frame shall be covered with heat moulded plain colour PVC C channel having a PVC strip of 20mm width stuck inside with solvent cement for stiles and plain colourPVC sheet for top rail , lock rail &bottom rail on eitherside& as gap insertfor top rail & bottom rail . Panellingof plain of plain colurPVC sheet to be fitted in the MS frame welded/sealed to stiles & rails with suitable PVC sheet beading and joined together with solvent cement ,etc all as specified & shown on drawingsand as directed 22 S&F 35mm thick flush shutter solid core constructionwith block board core and decorative face panels veneer with lipping/frame to match on both faces complete all as specified anddirected 23 S&F 300mm size mild steel sliding door bolt plate type stove enamelledblack with bright bolt not less than 12mm diaincl a minimum of six nut and bolts ,four on bolt plate and two on stapple plate complete all as specified & directed. 24 S&F mild steel barrel tower bolt 200mm size stove enamelled black with bright bolt etc all as specified & directed. 25 S&F 125 mm size mild steel pressed handle stove enamelled black and fixed complete all as specified anddirected. 26 S&F 100 mm size mild steel butt hinges medium weight cold rolled complete all as specified anddirected . 27 S&F floor door stopperaluminium alloy body and tounge 140mm anodised with hard drawn steel spring etc complete all as specified anddirected. 28 S&F Door closer hydraulically regulated, designation No. 3, universal type,aluminium extruded section suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified anddirected 29 S&Fgalvanized mild steel wire cloth 0.56mm dia of wire and average width of aperture 1.18mm fixed with tinned tack or galvanised wire staple, complete all as specified and directed . 30 S&F in repairsgalvanized mild steel wire cloth 0.56mm dia of wire and average width of aperture 1.18mm fixed with tinned tack or galvanised wire staple, complete all as specified and directed . 31 S&F in repair Vitreous china ware water closet Orissa pattern of size 580mm X 440mmincluding connecting to trap and to flushing pipe anti Syphonage pipe etc complete ,complete all as specified anddirected 32 S&F in repairs vitreous china water closet Padestal pattern( white ) includng trap but excluding fixing bolts, flushing cistern and flush pipe complete alldirected. 33 S&F in repairs PVC flushing cistern, 10 ltr capacity, valve less symphonic action type, low level, with intel, ball valve, float valve abd handle including brackets fixed in position, 32 mm dia PVC flush pipe and connection to water mains complete all as specified and directed. 34 S&F in repairs vitreous china urinal Half stall type, white, with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed. 35 S& F in repair vitrious china wash hand basin flat back550X400mm and padestalincl fixing bracket, pvc waste coupling and waste pipe,cp pillar tap (swan neck) etc all as specified and directed . 36 S&Fin repairs 600X450mm bevelled edge looking mirror of selected quality glass of 4mm thick etc mounted on AC board complete all as specified and directed. 37 Dismantling water tanks of any description exc 250 and n.exc 500 ltr capacity and removing to store complete all as specified and directed. 38 S&FRotational moulded polythene water storage tankstriple layered (cylinder each vertical with closed top) of capacity 500 Itrs, hoisted and fixed in position including pvc float valve 20mm size,specified in SSR Pt-1 , complete all as specified anddirected 39 Dismantling water tanks of any description exc 500 and n.exc 1000 ltr capacity and removing to store complete all as specified anddirected. 40 S&F Rotational moulded polythene water storage tankstriple layered (cylinder each vertical with closed top) of capacity 1000 Itrs, hoisted and fixed in position including pvc float valve 20mm size,specified in SSR Pt-1 ,complete all as specified anddirected . 41 Takingdown GI tubing and connections with all fittings 15 mm borecomplete all as specified anddirected. 42 S&F 15 mm dia GI water tubing ,medium grade with all fittings complete, fixed to wall and ceiling or laid in floors including making hole in RCC slabs for vertical pipes & making goods the same with cement concrete 1:2:4 including laid in floor etcetc complete all as specified anddirected. 43 All as per item No 42 above but 15 mm bore pipe but fixing only.. 44 S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified anddirected. 45 S&F in repair 15 mm bore dia bib tap (long or short body) cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for union fancy type chromium plated, concealed complete all as specified and as directed.. 46 S&F in repair 15 mm sizeStop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions , complete all as specified anddirected. 47 S&F in repair 15 mm bore stop valvecast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for union fancy type chromium plated,with long shank and cup (concealed type)complete all as specified and as directed.. 48 S &F in repairs PVC waste pipe of standard pattern not less than 75cm long 32 mm/40mm dia for WHB/steel sink waste coupling or suitable size complet all as directed. 49 M&L for preparing surfaces ofnew walls and applying two coats of oil bound distemper over and including a coat of wall care putty to achieve smooth finish surface on wall complete all as specified & dircted. 50 M&L for preparing surfaces new of walls and applying two caots of cement base paint over a coat of primercomplete all as specified & directed. 51 M&L for three coats of white wash on newly plastered surface of ceiling incl preparation of surface,complete all as specified & directed. 52 M&L for two coats synthetic enamel paint new wooden surface over 10 cm width or girth over a coat pink primer incl preparation of surfaces complete all as specified & directed. 53 M&L for two coats of synthetic enamel paint on new steel surface over 10cm width or girth over a coat red oxide primer incl preparation of surfaces complete all as specified & directed. 54 M&L forPCC1:4:8 type D-2using 40 mm graded stone agg as inin sub base, complete all as specified & directed. 55 S&F in repair PVC SWR pipe 110 mm dia fixed to walls, single socketed in any length with rubber ring joints fixed to walls etc all as specified & directed. 56 S&F in repair PVC SWR pipe 110 mm dia laid in trenches , single socketed in any length with rubber ring joints fixed to walls etc all as specified & directed. 57 S&Fin repairs100 mm dia stack clampmade out of25x4mmFlat iron etc all as specified & directed. 58 M&L for Complete repair of steel rolling shutters including servicing, overhaulingofrolling shutter gear operated type or hand operated type with chain wheel and hand chain of any size by oiling , greasing to gear box , repair/replacement to guide channel, shaft, pully, gear box, hood cover, pully, bearings etc and replacement of parts like spring, pins,lathe etc and including securing guide channel to walls with PCC 1:2:4 type B1 and making good the surfaces with CM (1:4), including welding of any thickness and making the rolling shutter functional to the entire satisfaction of the Engineer in chargecomplete all as specified and directed by Engineer-in Charge. (size of each shutter is 10 to 25 sqm) 59 Dismantling wrought ironor mild steel work of any description not otherwise provided for complete all as specified and as directed . 60 Taking down Rolling shutter shutters of any descriptionand not exc 10.00 sqm each complete all as specified anddirected 61 Taking down Rolling shutter shutters of any description exc 10.00 sqm each complete all as specified anddirected 62 M& L for 1.00 mm lath thickness Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual tyecomplete all as specified and directed. 63 M& L for 1.00 mm lath thickness Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete gear operated type with bevel gear box & crank handlecomplete all as specified and directed . 64 S&F in repair 3mm th sheet glass ordinary quality glazing with oil putty in square n.exc0.5 sqm in each pane,complete all as specified and directed. 65 All as per Item No. 64above butwith 3mm th pin head/ figuered glass. 66 S&F in repair 6.40mm th rough cast wired figured glass with screws in n.exc0.5 sqm in each pane complete all as specified & directed . 67 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing from site. 68 M&L for Coluredvitrified Ceramic tiles double charge 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc all as specified over and including 15 mm thick screed bed or bedding layer in CM (1:6),complete all as specified. 69 M&L for coloured vitrified double charge 10mm thick (sqare/rectangular ) polished, area of each tiles not exceeding 0.36 sqm in floor etc ,set and jointed in neat cement slurry and pointed in white or colouredcementto match etc all as specified over and including 15 mm th screed bed or bedding layer in CM (1:6) complete all as specified and directed. 70 M&L for Glazed ceramic tiles in vertical surface,skirting450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified over and including 10 mm thick rendering backing or bedding layer in CM (1:4)and directed. 71 M&L forPCC 25mmthick 1:2:4 type B1using 20 mm graded stone agg as in levelling course,complete all as specified and directed.. 72 M&L for machine pressed precast concrete interlocking paver block of required shape & size,confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and with pigmentlaid in required colour & pattern over25 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand., complete, all as ditected. (Note:- Sand for sand bedding shall be measured separately as supplied only.) 73 Supply only Sand forfilling under paver blocks. 74 M&Lfor 18-20 mm thick machine cut kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, over and including 20 mm thick screed or bedding layer in CM 1:6 complete all as specified and directed. 75 Dismantling brick tile or terracing tile single layer on roof complete all as specified and as directed by engineer-in-charge. (Bldg ht may vary upto 8.0 mtr & non accessible roof) 76 Demolition of mud in roofs any thickness including plastering and leeping (weather full thickness removed or part there of) complete all as specified anddirected . 77 Demolition of cement Concreteof any description and in any position not otherwise specifically provided forcomplete all as specified and as directed. 78 M&L for 50mm(average consolidated thickness)PCC1:3:6 type C2using 20mm graded stone aggregate as in padding on flat roofs etc, complete, all as specified and directed. 79 Supply only Integral water proofing compound , ISI marked. 80 M&L for Applying evenly a tack coat of industrial bitumen 85/25 at the rate of1.2 kg per sqm over a coat of primer including cleaning surfaces complete all as specified and as directed. 81 M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by torch application complete all as specified and as directed . 82 M&L for 40mm thick brick tiles laid on cement mortar bed ( 1:3) with WPC and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement and pointed in CM (1:3)complete all as specified and as directed. 83 All as per itemNo 82above but except brick tiles 84 M&Lfor Providing, cement concrete type B2 (1:2:4) (using 20 mmgraded stone aggregate), asin roof kerbs or mud stops, rounded or chamfered on edges parapets copings, bed plates, etc complete all as specified and as directed. 85 S&F anodised aluminium framepowder coated with minimum thickness of powder coating 50 micron for doors, windows, ventilatorswith one or more rebates including joining cleat for fixing, hinges etc. complete all as specified.Note:- Prelaminated partical board and sheet glass/wiremesh shall be measured and paid for separately. Make:- INDAL/HINDALCO/JINDAL or equivalent as per IS. 86 S&F anodised aluminium door shutters, powder coated aluminium section weighing 0.55 Kg/m ncluding necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, 2 Nos tower bolt of size 200 mm, hinges, anodised aluminum snap beading screws etc with chowkhat complete all as specified & directed. 87 S & F Anodised aluminium window and ventilator shutters, powder coated (minimum thickness of powder coating 50 micron) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats,hook and eye closure, Each door having 02 Nos D type handles, 02 Nos aluminium tower bolts 300 mm size, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified & directed. 88 S&F anodised aluminium window and ventilator shutters, powder coated fixed type without sash bar,aluminium section weighing 0.55 Kg/m ncluding necessary joining cleats,glazing clips, ruber rubber packing,handles 2 Nos per shutter,2 Nos tower bolts of 150 mm size per shuttter anodisd aluminium snap beading, screws etc with chowkhat complete all as specified & directed. 89 S&F 5.5 mm thick sheet glass selected quality and glazing with oil putty in squares n exc. 0.5 Sqm in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified anddirected 90 S&F 5.5 mm thick sheet glass selected quality and glazing with oil putty in squares exc. 0.5 Sqm in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified anddirected 91 S&F 9 mm thick Prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and as directed. 92 Cutting chases pinning in making good to facing where required and pointing in cement mortar (1:3) for concealed water tubing in brick walls cutting n.exc 10 cm girth. complete all as specified and directed. 93 S & F in repairs 15 mm diaBrass CP Sinkmixer for mixing hot & cold water screwed down for iron pipe and fixed,complete all as specified and directed. 94 S & F in repairs 15mm dia Brass CP central hole basin mixer with 450mm braided connection pipe (without pop-up) for mixing hot & cold water fixed in repairs, complete all as specified and directed. 95 S & F in repairs 15mm dia Brass CP wall mixer for mixing hot & cold water fixed in repairs, complete all as specified and directed. 96 M&L for damp proofing treatment to wall with two component acrylic polymer cementitios water proof elastomeric coating food grade mix to form uniform slurry and apply with paint brush as first coat then laying a layer of fibre glass mesh cloth as first coat is still green with overlap of joints of fibre mesh not be less than 10mm then finally apply second layer mix by brush to entire surface of contianer covering 0.6-0.78 Sqm/gm1mm thickness in two coats depending on the level of substrate and curing it minimum 3 days complete all as specified and directed. NoteQuoted rate shall be deemed to be inclusive of materials alll labours, tools and plants, scaffolding and working upto height 6m etc.
