Tender For Modernization Of Imfl Self Service Shop At Panipat, Haddo, Sri Vijaya Puram.- Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 2 1:2:4 (1cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 3 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 4 Centering and shuttering including strutting, propping etc. and removal of form for 5 Lintels,beams,plinthbeams,girders,bressumersand cantilevers 6 Steelreinforcement forR.C.C.workincludingstraightening,cutting, bending, placing in position and binding all complete above plinth level. 7 Thermo-Mechanically Treatedbars of gradeFe-500D or more. 8 Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking withpushandpull operationcomplete,including thecost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 9 80x1.20 mm M.S. laths with 1.20 mm thick top cover 10 Providing and fixing ball bearing for rolling shutters. 11 Cement concrete flooring 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 12 40 mm thick with 20 mm nominal size stone aggregate 13 Providing andapplyingplaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete. 14 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: 15 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 16 Wall painting with acrylic emulsion paint, of approved brand and manufacture, to give an even shade. 17 Two coats 18 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. 19 With cement mortar 1:4 (1 cement : 4 fine sand) 20 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 21 Nominal concrete 1:3:6 or richer mix (including equivalent design mix) 22 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) :For fixed portion 23 Polyester powder coated aluminium (minimum thicknessofpolyesterpowdercoating 50 micron) 24 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fastners of required dia & length (hold fast lugs or dash fastner shall be paid for separately) 25 Superior Hard Wood Cat - II (A) 26 Providing and fixing Billing Counter of size 2.90x1.80x0.75&1.05m with 18mm thick prelaminated HDF board including flap door, side door, draws with telescopic channel, shutters, locking arrangement, handles, hinges, all required fittings, materialsetc. complete as per approved drawings and as per the direction of Engineer-in-charge. 27 Providing and fixing Back Display Rack of size 2.50x0.40x2.10m with 18mm thick prelaminated HDF board including bottom cabinets and all required fittings, materilas etc.complete as per approved drawings and as per the direction of Engineer-in-charge.(Frame work shall be paid for separately) 28 Providing and fixing Baggage Rack of size 2.40x0.45x0.75 m with 18mm thick prelaminated HDF board including all required fittings& materilas etc. complete as per approved drawings and as per the direction of Engineer-in-charge. 29 Providing and fixing Security Counter of size 1.80x0.45x0.75&1.05m with 18mm thick prelaminated HDF board including handles, hinges, all required fittings & materials etc.complete as per approved drawings and as per the direction of Engineer-in-charge. 30 Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre etc. all complete as per requirement and direction of Engineer-in-charge. 31 Providing and fixing 12mm thick frameless toughened glass wall of approved make & manufacture including providing and fixing top&bottom pivot etc. all complete as per drawing and as per the direction of Engineer-in-charge. 32 Providing and fixing of automatic single sliding door operator, modular design, including internal cover with operator dimensions (H X T) : 100 x 180, 4150 mm Dorma-Germany or approved equivalent. The track profile should be separate from the main profile for enabling reduction in vibration insulation Microprocessor control self-learning reversing when obstrction is encountered. Microprocessor-controlled control unit. It should be Self-learning with adjustable parameters for opening and closing speed, hold-open time and opening and closing force. Class of protection IP 20. For opening size of 1.20 mm wide x 2.40 height.The system should have constant external power supply 230 V, 50/60Hz with 12mm frameless glass, 12mmthick clear toughened glass shutter. All complete as per specification and instrctionof the Engineer-in-charge.(Note: The work shall be executedas per manufacturers specifications wherever applicable, relevant code of practice and sound engineering practice. 33 Providing and fixing Name Board of frame size 8.70x0.65m in Backlit Acrylic sheet with Logo &ANIIDCOLIQUOR STORE with word height 0.45m etc. all complete as per approved drawing and as per the direction of Engineer-in-charge. 34 Providing and fixing of floor standing Price List Board in Backlit Acrylic sheet with Aluminium frame of size 1.80x2.25m all complete as per approved drawing and as per the direction of Engineer-in-charge. (Frame work shall be paid for separately). 35 Providing and fixing Premium Display Rack of size 3.85x0.45x2.70m with 18mm thick prelaminated HDF board including bottom cabinets with all materials like hinges,handles, locksetc.complete as per approved drawings and as per the direction of Engineer-in-charge.(Frame work shall be paid for separately). 36 Providing and fixing Front Display Rack having shelves with shutter of size 3.30x2.70x0.45/0.30m (for display) with 18mm& 12mm thick prelaminated HDF board including bottom cabinets with shutters & locking arrangement and shelves with 12 mm thick toughened glass fixed with cleat including all required fittings, materials etc. all complete as per approved drawings and as per the direction of Engineer-in-charge.(Frame work shall be paid for separately). 37 Providing and fixing partition wall with 12mm thick prelaminated HDF board including all required fittings & materials etc.complete as per approved drawings and as per the direction of Engineer-in-charge.(Frame work shall be paid for separately). 38 Providing and fixing factory made floor standing double sided height adjustable rack (heavy duty) 4x3 feet of approved quality as per approved drawings and as per the direction of Engineer-in-charge. 39 Providing and fixing height adjustable metal shelves (heavy duty) floor standing rack of height 7 feet with end cap of different sizes as per approved drawings and as per the direction of Engineer-in-charge. 40 Providing and fixing false ceiling at all height with 8mm thick fluted PVC vox panel of approved design on anodized aluminium frame work using JINDAL/INDAL or equivalent box section of size 50x50x2mm thick and 40x40x3mm anodized aluminium angle at not more than 0.60 mtrs centre to centre spacing as per actual requirement at curves, junctions jointed with all necessary fixtures such as cleat angles,brackets, screws etc.complete as directed by Engineer-in-charge. 41 Aluminium panelling with anodized frame 42 Providing and fixing 8mm thick fluted PVC vox panel of approved design for wall on anodized aluminium frame work using JINDAL/INDAL or equivalent box section of size 50x25x3mm thick and 25x25x3mm anodized aluminium angle at not more than 0.60 mtrs centre to centre spacing as per actual requirement at curves, junctions jointed with all necessary fixtures such as cleat angles,brackets, screws etc.complete as directed by Engineer-in-charge. 43 Aluminium panelling with anodized frame 44 Providing and fixing false ceiling at all height with aluminium composite panel(ACP) 6mm thick (0.50+5.00+50mm) on anodized aluminium frame work using JINDAL/INDAL or equivalent box section of size 50x50x2mm thick and 40x40x3mm anodized aluminium angle at not more than 0.60 mtrs centre to centre spacing as per actual requirement at curves, junctions jointed with all necessary fixtures such as cleat angles,brackets, screws etc. fixed to ceiling with necessary high performance imported double side CHB tapes, structural seatant (DOWCORNING NO.789,998) fixed so as to transfer the weight of Alcon panels (ACP) to aluminium frame work and to avoid undue stress on silicon sealant, closing the grooves (12-16mm) with weather grade silicon dealant ensuring the whole system water proof, rigid against wind using conversion resisitanthardware necessary paints thermal expansion/contration mechanism etc. complete as directed by Engineer-in-charge. 45 Aluminium panelling with anodized frame 46 Providing and fixing door shutters with 12mm prelaminated HDF board including hinges, handles, tower bolts etc. complete as per the direction of Engineer-in-charge. 47 Providing and fixing door shutters with 18 mm thick prelaminated HDF board including hinges, handles, locking arrangements etc. complete as per the direction of Engineer-in-charge. 48 Providing and fixing C type box of size 0.35x0.15x0.45m with thickness 0.04m made of 18 mm thick prelaminated HDF board including all required materials etc. complete as per approved drawing and as per the direction of Engineer-in-charge. 49 Providing and fixing C type box of size 0.35x0.15x0.27m with thickness 0.04m made of 18 mm thick prelaminated HDF board including all required materials etc. complete as per approved drawing and as per the direction of Engineer-in-charge. 50 Providing and fixing brand Name Board in Backlit Acrylic sheet of size 450x200 mm etc. all complete as per drawing and as per the direction of Engineer-in-charge. 51 Providing and fixing heavy duty slotted angle racks of approved quality 52 Providing and fixing of ducting for strip lights with 12mm thick BWP 710 marine plywood, 1mm thick lamination on exposed area and bottom cover with 4mm thick froasted glass including hanging arrangementetc. all complete as required and as per the direction of Engineer-in-charge. 53 ElectricalWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 54 Group B 55 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 56 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 57 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 58 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 59 25 mm 60 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 61 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. 62 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. 63 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required. 64 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 65 6 way (4 + 18), Double door 66 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 67 Single pole 68 Triple pole and neutral 69 Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 70 40 A 71 63 A 72 Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required. 73 Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required. 74 Supplying and fixing of 18W LED surface mounted general purpose square shaped luminaire with low height CRCA housing and high transmissivity diffuser (200x200mm) Make:- Philips or equivalent in Bajaj/Havells/Crompton etc. complete with all accessories etc. as required. 75 Supplying and fixing of 3W LED new series of LED spot light specially designed for commercial usage long life with 30000 burning hours with CRI>80 wide Make:- Crompton or equivalent in Bajaj/Havells/Philips etc.complete with all accessories etc. as required. 76 Supplying and fixing of 25W flexible LED strip light with high brightness Make:- Bajaj or equivalent in Philips/Havells/Crompton complete with all accessories etc. as required. 77 Supplying and fixing of 25W LED strip Driver Make:- Bajaj or equivalent in Philips/Havells/Crompton etc. as required. 78 Supplying and fixing of Philips LED profile light for decoration, profile shine, cool day Make:- Philips or equivalent in Bajaj/Havells/ Crompton/ ACE/Luker complete with all accessories etc. as required. 79 Supplying and fixing of Philips LED transformer 25 to 60 watts 5A 12V DC for profile light strip Make:- Philips or equivalent in Bajaj/Havells/Crompton/ ACE/Luker etc. as required. 80 Supplying and fixing of 600mm sweep ceiling fan Make :- USHA or equivalent in Havells/Bajaj/ Crompton/RR Fans/Orient complete with all accessories etc. as required. 81 Supplying and fixing following way, single pole and neurtral, sheet steel, MCB distribution board, 240 V, on surface/recess, complete with tinned copper bus bar,neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc.as required (But without MCB/RCCB/Isolator) Make:- Havells or equivalent in Indoasian/Legrand/ L&T. 82 4 way, Double door Make:- Havells or equivalent in Indoasian/Legrand/L&T 83 Supplying, Installation, testing and commissioning of fixed thermal and fixed magnetic setting Loadline Moulded Case Circuit Breakers (AC 415V), 35 KA breaking capacity, 250 Amps Four Pole Make:-Havells Cat No.IHLFN40250 or equivalent in Legrand/L&T/Indoasian in the existing panel board etc. as required. 84 Supplying and fixing of Kit-Kat Rewireable (Porcelain fuse carrier & Base) 320 A/415V Make:-Havells Cat No.IHKKRN4320 of ISI standard or equivalent in L&T/Legrand/Indoasian including connection, testing etc. as required. 85 Supplying,installation,testing & commissioning of Earthing with ASHLOK make SEE brand safe earthing electro type-19, 48mm dia, length 2 mtrs equivalent by filling inner space with 50 Kg (2 bags) Electrodite (Back fill compound) required for safe earth electrode and providing masonry enclosure with C.I cover plate having locking arrangement etc. as required. 86 Supplying and fixing of 2.5 Tonne Split type Air Condition of approved brand and manufacturer (Carrier, Amtrax, LG, Hitachi, Voltas, Blue Star, Godrej,Llyods,Cruise,Panasonic etc.) with remote control, suitable stabilizer of wall mounted type of approved make and manufacture including fixing of stabilizer, supplying and fixing of switch board, power switch, socket and providing holes wherever necessary for fixing the Split AC and including fixing charges, labours, tools, copper piping, clamps, screws,with all necessary accessories etc complete. 87 Providing and fixing ofrefrigerant copper pipes of following sizes (Suction & delivery) of Split type AC i/c providing electrical cables, insulation, extra gas charging, cutting,drilling holes on the wall for passing gas pipes, fixing suitable size PVC pipe on the wall through the holes and cementing, painting to give an even look and smooth finish and covering with PVC non adhesive tape over the insulation of refrigerant pipes and as per the direction of Engineer-in- charge. 88 Refrigerant copper pipes of sizes 3/4 and 1/2
