|
| 1 | M & L for preparation of old painted surfaces (cleaning all dust etc) of steel or iron of any description over 10cm in width or girth, not otherwise described and applying spray painting with synthetic enamel paint (1st grade quality) of approved colour, complete all as specified and directed. |
| 2 | M & L for complete removal of existing treatment of old painted surfaces (cleaning all dust including filling cavities with filler etc) of steel or iron of any description over 10cm in width or girth, not otherwise described and applying spray painting with synthetic enamel paint (1st grade quality) of approved colour over and including spraying a coat of red oxide primer, complete all as specified and directed. |
| 3 | M & L for preparation of surfaces by cleaning, scrapping etc for transformer, voltage stabilizer, isolation transformer and other similar equipment not more than 630 KVA and applying spray painting with synthetic enamel paint (1st grade quality) of approved colour, complete all as specified and directed. |
| 4 | M & L for preparation of surfaces by cleaning, scrapping etc for DG set and other similar equipment not more than 550 KVA and applying spray painting with synthetic enamel paint (1st grade quality) of approved colour, complete all as specified and directed. |
| 5 | M & L for power cable route marker pre-cast RCC of size 1500mm x 300mm x 50mm with top curved portion, 8mm dia round bar reinforcement, emboshing of letter (MES-POWER CABLE) both faces of pre-cast during casting of RCC pre-cast, applying two coats of external emulsion paint with primer approved colour and painting of emboshed surface with black colour including earth work for fixing of route marker, complete all as specified and directed. |
| 6 | Demolition of reinforcement cement concrete set in cement morter, complete all as specified and directed.(Note : Reinforcement cut as required to facilated demolition.) |
| 7 | M & L for precast reinforced cement concrete (1:2:4), type B-1 (using 20 mm graded stone aggregate) as in cover slabs (for manholes, drain etc) and similar articles with plain faces and set in cement mortar (1:4) including form work, complete all as specified and directed.(Note : Re-inforcement shall be measured and paid seperately) |
| 8 | M & L for mild steel TMT bars 6mm to 8mm dia., cut to length, bent to shape required, including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. |
| 9 | M & L for detecting fault through cable fault deductor by injecting suitable energy pulse to detect exact position of fault for XLPE, LTcable, 1100 volts grade heavy duty aluminium conductor any size including transporting chagres and clearing of rectification of fault of electric supply by removing of burnt out portior of cable from loop, etc including earth work, complete all as specified and directed.Notes :- Cost of lugs shall be measured and paid seperately. |
| 10 | M&L straight through joints (epoxy) cable joint kit including jointing materials for making joints of UG electric cable 1100 volt grade heavy duty with PVC/XLPE insulated aluminium conductor nominal cross sectional area 10 to 16 Sqmm 3.5/4.0 core and testing, complete all as specefied and directed. |
| 11 | M&L straight through joints (epoxy) cable joint kit including jointing materials for making joints of UG electric cable 1100 volt heat shrinkable, grade heavy duty with PVC/XLPE insulated aluminium conductor nominal cross sectional area 25 to 50 Sqmm 3.5 core and testing, complete all as specefied and directed. |
| 12 | M&L straight through joints (epoxy) cable joint kit including jointing materials for making joints of UG electric cable 1100 voltheat shrinkable, grade heavy duty with PVC/XLPE insulated aluminium conductor nominal cross sectional area 70 to 150 Sqmm 3.5 core and testing, complete all as specefied and directed. |
| 13 | M&L straight through joints (epoxy) cable joint kit including jointing materials for making joints of UG electric cable 1100 voltheat shrinkable, grade heavy duty with PVC/XLPE insulated aluminium conductor nominal cross sectional area 185 to 300 Sqmm 3.5 core and testing, complete all as specefied and directed. |
| 14 | S&F factory fabricated busbar chamber outdoor type made out of 3.15mm thick CRCA sheet with powder coating of size not less than 1.00 x 0.8 x 0.6 for set of 04 aluminium busbar 400 Amps rating, supported with suitable size heavy duty porcelin stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving. The bar shall be colour coded (red, yellow and blue) for three phases and black for neutral, The Chamber shall be fixed 60cm above the normal ground level complete with PCC foundation (1:2:4 ) type B2 and fixing arrangement with angle iron 50 x 50 x 6mm, complete all as specified and directed. |
| 15 | Demolition of cement concrete unreinforced in ground floors and paving n. exc. 15cm thickness (below or above ground level) and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100m, complete all as specified and directed. |
| 16 | M&L for PCC(1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in foundation of poles, filling and mass concrete etc, complete all as specified and directed. |
| 17 | Demolition of brick work or stone masonry, built in CM including all quoins, arches, pillars etc. but excluding ashlar facing, dressed stone work and precast concrete articles , complete all as specified and directed. |
| 18 | M & L for brick work with sub-class ‘B\" bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6), complete all as specified and directed. |
| 19 | All as per item No. 18.00 here-in-before but except bricks, complete all as specified and directed.Note : (i) Bricks obtained from demolition shall be re-used.(ii) The quoted rate shall deemed to be included for cleaning of old bricks obtained from demolition. |
| 20 | M&L 15mm thick rendering in CM (1:4) on other than fair faces of brick work or concrete surfaces of wall, finished even and smooth without using extra cement, complete all as specified and directed. |
| 21 | M&L for hardcore of gauge not exceeding 63mm of broken stone, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, complete all as specified and directed. |
| 22 | M&L 75mm thick PCC (1:3:6 ) type C-2, (using 40mm graded stone aggregate) for sub base of floor, plinth prtection, path/ hard standing etc, complete all as specified and directed. |
| 23 | M&L for 100mm thick PCC (1:2:4) type B- 2 (using 40mm graded crushed stone aggregate) as in floors, pavings, hardstanding etc., complete all as specified and directed. |
| 24 | M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistance primer, complete all as specified and directed. |
| 25 | S&F in repair danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, 20 x 15cm size, complete all as specified and directed. |
| 26 | S&F in repair danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, 25 x 20cm size, complete all as specified and directed. |
| 27 | Excavation in trenches not exceeding 1.5 metre wide and not exc 1.5 metre in depth for foundation of pole/stay, or cable trenches and getting out in soft/loose soil, complete all as specified and directed. |
| 28 | Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm in soft/loose soil, complete all as specified and directed. |
| 29 | Removing excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point in any type of soil, complete all as specified and directed. |
| 30 | Lifting, and relaying the existing PVC/XLPE insulated, armoured, heavy duty electric cable with aluminimum conductor, 1100 Volts grade, in trenches/fixed on wall for cross- sectional area of cable of size from 185 Sqmm to 300 Sqmm 3.5 core, complete all as specified and directed.Note: (i) Necessary excavation and earth work shall be measured and paid separately. (ii) Unit quoted rate shall deemed to be included the cost of lugs of suitable size and cable gland irespective of length of cable etc . |
| 31 | All as per itme No 30.00 here-in-before but 70 Sqmm to 120 Sqmm 3.5 core, complete all as specified and directed. |
| 32 | All as per itme No 30.00 here-in-before but 35 Sqmm to 50 Sqmm 3.5 core, complete all as specified and directed. |
| 33 | All as per itme No 30.00 here-in-before but 10 Sqmm to 25 Sqmm 3.5/4 core, complete all as specified and directed. |
| 34 | M&L for sub class \"B\" old size bricks, laid flat, dry in trenches for cable protection, complete all as specified and as directed. |
| 35 | Supply, filling in trenches, spreading, leveling sand cushioning 8cm below cable and 15cm above the cable punned down to 18cm for under ground cable, complete all as specified and directed.(Note : Punned thickness shall be measured for payment) |
| 36 | Supply and laying un-reinforced precast concrete cable cover, class HV, type 2, flat, size 450mm x 180mm x 40mm with minimum average braking load 350 kg, as per IS-5820 : 1970, complete all as specified and directed. |
| 37 | M&L for preparation of old painted steel or iron surfaces of panel board, E/M plant & equipments etc. of any description over 10cm width or grith and applying two coats of synthetic enamel paint (1st grade quality) (using spary painting machin), complete all as specified and directed |
| 38 | M&L for sealing of cable entry portion in order to make LT/HT panel/RMU/VCB panel dust and vermin proof by using loctite tite foam PU sealant, white, expanding foam for large gap filling, complete all as specified and as directed. |
| 39 | Supply only loctite tite foam PU sealant (340gm each), white, expanding foam for large gap filling of electric panel, complete all as directed. |
| 40 | Supply only CRC electric contact cleaner sprey of capacity 500 ml, complete all as directed. |
| 41 | S&F GI cable tray of size 100mm wide x 60mm high, 0.6mm thick including fixing arrangement, suspenders, complete all as specified and directed. |
| 42 | S&F GI cable tray of size 150mm wide x 60mm high, 0.6mm thick including fixing arrangement, suspenders, complete all as specified and directed. |
| 43 | S&F GI cable tray of size 200mm wide x 60mm high, 0.6mm thick including fixing arrangement, suspenders, complete all as specified and directed. |
| 44 | S&F GI cable tray of size 300mm wide x 60mm high, 0.6mm thick including fixing arrangement, suspenders, complete all as specified and directed. |
| 45 | S&F wall mounted signage, consisting of zinc sulphide photo luminescent coating on acrylic sheet as in exit/staircase/extinguisher location/ fire location/ prohibited are etc, maximum width 300mm and length 600mm, complete all as specified and directed. |
| 46 | S&F LED type integral aviation obstruction light (Heavy duty) IP 65/66 protection, single light fitting comprising of Die-cast aluminum housing with Red polycarbonate dome for better illumination, integral driver, Supper flux 5mm 302 Nos LEDs incorporated, powder coated aluminium housing with polycarbonate enclosure including taking down unserviceable aviation light fittings, complete al as specified and directed. |
| 47 | M&L for 12 volt, 10 Amp auto battery charger for generator, lead acid type, complete all as specified and as directed. |
| 48 | Supply and testing digital clamp meter upto 1000 Amp, AC, 4 K Ohm resistance, DC and continuity etc, complete all as specified and as directed. |
| 49 | S&F in repair lightening arresters expulsion type complete with all fittings, transmission class, discharge capacity 65 KA and connection to earth strip, complete all as specified and as directed. |
| 50 | M&L for cleaning/painting the SMC/MS junction box of size 500 x 400 x 350mm mounted on security light pole of different rating bus bar after dismantling the incomming and outgoing connections from MCCB/ bus bar and replacing theold unserviceable nut, bolts, supporting insulators etc, and check the serviceability of MCB/MCCB andincomming & outgoing cabls/eires and removing existing old insulation of bus bar and MCCB/MCB terminals and providing new insulation tape of standard quality applied to bus bar and MCCB terminals and after the completion of job it is ensured the box must be properly close and dust and vermin proof, complete all as specified and directed.Note : (i) Contractor has to take the shut down of LT panel before starting the job and switch on the panel after completion of work.(ii) One MCB 6 to 32 Amp and minor repair shall deemed to be included in the unit quoted rate. |
| 51 | S & F LED Indicating lamp set for main supply indicating (R, Y, B), complete all as specified and directed. |
| 52 | S & F selector switch for manual and auto operation, complete all as specified and directed. |
| 53 | S & F digital/analoge voltmeter 0-500 volt, three phase, accuracy class-1 of size 96mm x 96mm for existing pannel including CT ratio-1/5, complete all as specified and directed. |
| 54 | S & F digital/analoge ammeter, range 10 Amp to 500 Amp, three phase, accuracy class-1 of size 96mm x 96mm for existing pannel including CT ratio-1/5, complete all as specified and directed. |
| 55 | S & F multifunction meter (MFM), three phase, accuracy class-1 of size 96mm x 96mm for existing pannel including CT ratio-1/5, complete all as specified and directed. |
| 56 | M&L for in replacement of pre-cast RCC slab cover of size 600mm x 600mm x 50mm with PCC type B-1, (1:2:4) set to CM (1:4) using 8mm TMT bar having centre to centre distance not more than 100mm, 02 Nos. handles made up of 8mm TMT bar of rectangular shape including applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide/zinc crome primer, complete all as specified and as directed. |
| 57 | All as per item No 56.00 here-in-before but of size 800mm x 400mm x 50mm, complete all as specified and directed. |
| 58 | All as per item No 56.00 here-in-before but of size 1150mm x 400mm x 50mm, complete all as specified and directed. |
| 59 | All as per item No 56.00 here-in-before but of size 600mm x 400mm x 50mm, complete all as specified and directed. |
| 60 | All as per item No 56.00 here-in-before but of size 750mm x 400mm x 50mm, complete all as specified and directed. |
| 61 | All as per item No 56.00 here-in-before but of size 900mm x 400mm x 50mm, complete all as specified and directed. |
| 62 | M & L for road cutting/removing the hard standing/cutting plinth protection of building/path for laying of pipe line of any size including making good disturbed surfaces after laying of cable, as per existing, complete all as specified and directed. |
| 63 | M & L for PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) for making good to disturbed surfaces of road/hardstanding etc, complete all as specified and directed. |
| 64 | M&L for 100mm bore, ductile iron pipe (K-7), socket and spigot end as per IS:8329 with internal cement mortar lining and external bitumen coating for potable water supply with and including rubber ring joints as per IS:5382 (1985), giving satisfactory hydraulic field testing and commissioning as per technical specification etc laid in trenches including taking out/down old unserviceable pipe any type, complete all as specified and directed.(Note: Excavation and earth work shall be measured and paid separately under respective items) |
| 65 | All as per item No 64.00 here-in-before but 150mm bore, complete as specified and directed. |
| 66 | S&F CPVC pipe of size 75mm inner dia in trenches, high pressure, CPVC pipes, schedule 40 & plain CPVC schedule 80 fittings, including all necessary fittings, like elbow, tee, socket, reducer, bushings, step over bends, end caps, end plugs, etc. and with CPVC solvents cement including taking down old unserviceable pipes, complete all as specified and directed. |
| 67 | All as per item No 66.00 here-in-before but of size 50mm inner dia, complete as specified and directed. |
| 68 | All as per item No 66.00 here-in-before but of size 25mm inner dia, complete as specified and directed. |
| 69 | S&F 50mm bore GI water tubing and connection, medium grade, with all fitting fixed to wall or in ceiling or laid in floors including taking down old unserviceable pipe, complete all as specified and directed. |
| 70 | S&F 25mm bore GI water tubing and connection, medium grade, with all fitting fixed to wall or in ceiling or laid in floors including taking down old unserviceable pipe, complete all as specified and directed. |
| 71 | S&F 200mm bore CI sluice valve, flanged end, class PN 1.6 (IS-14846) with brass spindle and hand wheel including necessary gasket, nuts and bolts, washer etc. including taking down old unserviceable sluice valve, complete all as specified and directed. |
| 72 | S&F 150mm bore CI sluice valve, flanged end, class PN 1.6 (IS-14846) with brass spindle and hand wheel including necessary gasket, nuts and bolts, washer etc. including taking down old unserviceable sluice valve, complete all as specified and directed. |
| 73 | S&F 100mm bore CI sluice valve, flanged end, class PN 1.6 (IS-14846) with brass spindle and hand wheel including necessary gasket, nuts and bolts, washer etc. including taking down old unserviceable sluice valve, complete all as specified and directed. |
| 74 | S&F 80mm bore CI sluice valve, flanged end, class PN 1.6 (IS-14846) with brass spindle and hand wheel including necessary gasket, nuts and bolts, washer etc. including taking down old unserviceable sluice valve, complete all as specified and directed. |
| 75 | M & L for cutting existing steel tubing of size40/50mm for alterations or additions (each cut measured), complete all as specified and directed. |
| 76 | M & L for screwing existing steel tubing of size 40/ 50mm for alterations or additions (or lengthening screw on pipe to form connector), complete all as specified and directed. |
| 77 | S&F 50mm bore gun metal gate/globe valve with iron wheel head, screwed both ends suitable for fixing with CPVC/GI pipe and taking down old unserviceable valves, complete all as specified and directed. |
| 78 | S&F 40mm bore gun metal gate/globe valve with iron wheel head, screwed both ends suitable for fixing with CPVC/GI pipe and taking down old unserviceable valves, complete all as specified and directed. |
| 79 | S&F 25mm bore gun metal gate/globe valve with iron wheel head, screwed both ends suitable for fixing with CPVC/GI pipe and taking down old unserviceable valves, complete all as specified and directed. |
| 80 | S&F 20mm bore gun metal gate/globe valve with iron wheel head, screwed both ends suitable for fixing with CPVC/GI pipe and taking down old unserviceable valves, complete all as specified and directed. |
| 81 | S&F in repair 50mm bore CPVC ball valve suitable for CPVC pipe, complete all as specified and directed. |
| 82 | S&F in repair 40mm bore CPVC ball valve suitable for CPVC pipe, complete all as specified and directed. |
| 83 | S&F in repair 25mm bore CPVC ball valve suitable for CPVC pipe, complete all as specified and directed. |
| 84 | S&F rotational moulded polyethylene water storage tanks, (made 100% virgin and food grade plastic), triple layered, (cylindrical vertical with closed top) ISI marked, confirming to IS 12701-1996, hoisted and fixed in position all as specified in SSR Part I (500 ltr capacity) including 20mm Nipple suitable for HDPE water tank and 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed to 20mm bore pipe inculding dismantling of old unserviceable water tank of any capacity, complete all as specified and directed. |
| 85 | M&L for cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under aluminium coat and one aluminium finishing coat of paint complete for base support frame for water tanks at roof top/ground floor including dismantling of old unserviceable cross arm/bracings etc, complete all as specified and directed. |
| 86 | Taking up or down steel tubing and connections, of size 20/25mm bore from walla, ceiling floor etc including cleaning and refixing the same including connection, in new or old position, complete all as specified and directed. |
| 87 | M & L for run lead joints in position for cast iron spigot and socket ends pipes of size 200mm bore including providing new spun yarn jute etc, as required, complete all as specified and directed. |
| 88 | M & L for run lead joints in position for cast iron spigot and socket ends pipes of size 150mm bore including providing new spun yarn jute etc, as required, complete all as specified and directed. |
| 89 | M & L for run lead joints in position for cast iron spigot and socket ends pipes of size 100mm bore including providing new spun yarn jute etc, as required, complete all as specified and directed. |
| 90 | M & L for run lead joints in position for cast iron spigot and socket ends pipes of size 80mm bore including providing new spun yarn jute etc, as required, complete all as specified and directed. |
| 91 | M & L for DI fitting upto 200mm bore for bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch. \"Y\" junction, double branch, cross (flange sockets or socket and spigot) collars, caps and plugs, complete all as specified and directed. |
| 92 | M & L for CI fitting upto 200mm bore for bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch. \"Y\" junction, double branch, cross (flange sockets or socket and spigot) collars, caps and plugs, complete all as specified and directed. |
| 93 | Attending pipeline breakdown of CI/DI/GI pipe of 80/100/150/200mm dia by making lead joint with lead and spun yarn and moulding clay including takin up/down pipe using chain pulley or rope and excavation in any type of soil including returning filling and removal of soil and testing of pipe, complete all as specified and directed.Note : Lead joint /titon joint/material/fitting/pipe shall be measured and paid seperately. |
| 94 | & L for boring of holes under road, pavement, hard standing by using trenchless technology, using ultra sounding technique without damaging the existing road/path/hardstanding etc for laying GI/ (DWC) HDPE pipe upto 150mm dia, not less than 1.0m below GL, complete all as specified and directed. |
| 95 | M & L for construction of valves pit chamber of size (1200mm x 1200mm x 1200mm, internal), 15cm thick PCC foundation using PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate), 25cm thick brick wall, using old size burnt clay brick in CM (1:4), 10mm thick rendering on internal and extranal surfaces both in CM (1:4), PCC (1:2:4) type B1 coping (using 20mm graded crushed stone aggregate) for grouting MS frame including foundation 3mm thick MS top sheet cover with locking arrangement including 50mm pad lock with double key arrangement, MS frame work made out of 40 x 40 x 5mm thick angle iron including painting of steel surface with two coats of synthetic enamel paint over a coat of red oxide primer incuding necessary excavation in any type of soil, returning, filling in and removal of surplus soil to a distance not exceeding 50 mtrs including demolition of existing cracked valve chamber, complete all as specified and directed. |
| 96 | All as per item No 95.00 here-in-before but of size (900mm x 900mm x 900mm, internal), complete as specified and directed. |
| 97 | Note: An amount of Rs.88,205.00 on account of Credit Schedule for schedule \"A\" part - II shall be deducted from the total amount of BOQ to arrive at the contract sum. |
| 98 | Supply and fixing energy efficient ‘LED Flood Light120 W LED luminairewith Aluminium dia cast housing, toughened glass cover with IP 66 protection, CCT 5700 K including fixing arrangment on wall/pole / surface and connecting cable up to nearest ceilign rose into flexible PVC conduit. Make : Crompton/Havells/ Surya/Philips |
