Tender For Special Repair Works Of Boys, Hostel No-4 Of Jgec- Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.(a) upto 150 mm. thickIn Ground Floor 2 In First Floor 3 In Second Floor 4 Roof treatment by application of non toxic polyurethane modified acrylic based single component (P U Roof Coat) solvent free, cold applied polyurethane modified elastomeric waterproofing membrane with excellent UV resistant capacity as per ASTM D6083fa water based 100% acrylic elastomeric emulsion polymer latex coating, used as protective coating for roofs} after preparing the surface by cleaning and repairing the roof cracks by cement & sand mortar (1:4), preferably with antishrinkage mortar (to be paid separately) if any, apply two coats along with a priming coat (two coats of P U Roof Coat and one coat of primer coat compatible with main product as per manufacturers specification) and reinforced with or without 20 gsm Geotextile Fleece, including the cost of primer coat and base preparation, tools & plants but excluding the cost of scaffolding and stagging complete as per direction of Engineer -in-charge. 5 Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. (a) Pakur Variety 6 In First Floor 7 In Second Floor 8 Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars.a) In ground floor including roof. 9 In First Floor 10 In Second Floor 11 Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturers specification [Cement to be supplied by the Department] 12 Applying 2 coats of Non-Toxic Acrylic Polymer modified Paint having adhesive & waterproofing properties by mixing in proportion (1 liquid: 4 cementitious material) or as per manufacturers specification for water proofing layer in water tank etc. (No Departmental Cement is required) 13 Extra rate for using water proofing and plasticising admixture @ 0.2% by weight of cement (or at manufacturers specified rate) for concrete of various grades. 14 M.S. works in brackets made from flats, angles, tees etc. to sizes specialy bent, twisted, forged; making holes drilled and fitted to rafter of trusses with necessary bolts, nuts, washer or screws etc.(length of straight not less than 230 mm) 15 Supplying, fitting and fixing single skin colour coated trapezoidal profile for wall cladding. Roof shall be made of 0.45 mm BMT (Base Material Thickness) (0.50 mm TCT (Total coated thickness excluding paint), G550 (min 550 yield strength), of Zincalume metalic coating (ISI 5965) with high solar reflectance index (SRI) value for better cooling as per thermatch technology, 1000 - 1015 mm effective cover width with five major corrugation, 28 mm high rib spaced at 203 mm c/c with subtle square fluting in the pan and the end rib shall have anti-capillery groove and return leg. The steel sheet shall be fastened with 40 micron zinc coated or 25 micron zinc - tin alloy coated, hex head self - drilling screw as per IS 3566 - 2002 class 3 fastener. The base steel shall be coated with zinc - alluminium alloy zincalume (AZ150) (i.e. 55% Al, 43.4 % Zinc, 1.6% Si) minimum of 150 g/m2 coating total on both sides, pre -painted with colourbond XRW (exterior roofing, walling) paint system of 35 micron Super Durable Polyster paint (SDP) with stable inorganic treatment with no lead contents confirming ISI 15965. The sheet shall be free from defects and have brand marking of the manufacturer giving product details on the back of the sheet at regular interval confirming genuinity of the material. (i) In Roof:- (a) With 0.5 mm thick sheet 16 Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete.(In all floors for internal wall & upto 6 m height for external wall) (ii) 3 mm thick 17 Above6 m hight 18 Renewing worn out putty of glass pane (a) Panes not exceeding 0.2 Sq.m 19 M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. Grill weighing above 16 Kg./sq.mtr and above 20 Reparing collapsible gate by cutting out all rivets as necessary reassambling all members including welding pieces of channels, sraightening bent bars and rivetting with new rivets and fitting in position and painting two coats. 21 Easing and oiling, cleaning collapsible gate and repairing to locking arrangements. 22 Renewing bottom rail or top runners of collapsible gate including mending good all damages. 23 Welding in M.S. structural work with gas or electric:(a) Tack weld 24 Cleaning the exposed reinforcement preferably upto full diameter by wire brush, applying two coats of polymer based rust removing compound left for 24 hours, removing the coating and then applying two (2) coats of polymer modified anti corrosive protective coating formulated to inhibit the corrosion of reinforcement as per manufacturers specification] [Mode of measurement:The affected surface area of reinforcement shall be considered for payment] 25 Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. a) Depth of excavation not exceeding 1,500 mm 26 Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes.a) Pakur Variety 27 Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) 28 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. 29 In First Floor 30 In Second Floor 31 Brick work with 1st class bricks in cement mortar (1:4)In superstructure, ground floor 32 Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.For works in foundation, basement and upto roof of ground floor/upto 4 mSAIL/ TATA/RINL 33 In First Floor 34 In Second Floor 35 Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. 36 In First Floor 37 In Second Floor 38 Supplying & laying as per IRC-SP:063-2004 paver unit of any shade of approved quality as per relevant IS code, laid in pattern as directed in pavement, footpath, driveway (paver block only), etc including necessary underlay complete in all respect with all labour and material. [Border concrete if necessary to be paid separately]. Note: Sub-grade CBR should not be less than 5.25 mm thick Tiles as per IS: 1237-2012 for footpath,ramp,staircase of public building (over 25 mm thick (Avg) Cement mortar (1:3) & Cement Slurry @ 4.4 kg /Sq.m at back side of Block. Cement for Mortar & Slurry to be supplied by Department). (ii) Coloured Decorative 39 Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. 40 Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor). [Excluding cost of chipping over concrete surface]With 1:4 cement mortar. 15 MM thick plaster 41 First Floor 42 Second Floor 43 Third Floor 44 With 1:4 cement mortar10 MM thick plaster Ground Floor 45 First Floor 46 Second Floor 47 Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE: Cement 0.152 cu.m per100 sq.m. 48 Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencreteurface old or new surface to receive decorative textured(matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the EIC.In Ground floor. One coat 49 First Floor 50 Second Floor 51 Third Floor 52 Protective and Decorative Acrylic exterior emulsion paint of approved quality, as peranufacturers specification and as per direction of EIC to be applied over acrylic primer as required. The ratencludes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.Normal Acrylic Emulsion. In Ground floorTwo coats. 53 First Floor 54 Second Floor 55 Third Floor 56 Dismantling artificial stone flooring upto 50 mm. thick by carefully chiselling without damaging the base and removing rubbish as directed within a lead of 75 m. In ground floor including roof. 57 Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. Wall:With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg /Sq.m.Area of each tile above 0.09 Sq.m. Coloured decorative. Ground floor 58 First Floor 59 Second Floor 60 Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturers specification) including cleaning and smoothning of surface. Two Coats 61 White washing including cleaning and smoothening surface thoroughly. All floors:(b) Two coats (to be done on specific instruction). 62 18 mm. to 22 mm. thick, kota stone slab set in 20 mm thick (avg) cement mortar (1:4) in floor, stair & lobby including pointing in cement slurry with admixture of pigment matching the stone shade, including grinding & polishing as per direction of Engineer - in - charge to match with the existing work. [Slurry for bedding @ 4.4 kg /Sq.m and pointing @ 2.0 kg/Sq.m] 63 Taking out shutter of door and window, dismantling by parts (for repair orreplacement of damaged parts) , reassembling and refitting and rehanging same with old fittings but with new screws as necessary. (Where different parts of same shutter are renewed under different item, payment under item 73 will be made once only). 64 Labour for taking out door and window frame including shutter for repair or replacement ofdifferent parts of the frame & refixing the same including mending good all damaes complete. (Concrete and brick work for mending damage will be paid separately)Upto area 2.5 Sq.m 65 Above area 2.5 Sq.m 66 Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals).Sal : Siliguri. 67 Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. (In case of non-supply of single plank, penal rate of reduction of 20% will be made)35mm thick shutters with 19mm thick panel of size 30 to 45 Cm.Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. Ground floor 68 First Floor 69 Second floor 70 Shutters of 2/3rd panel and 1/3rd glazed of doors and windows as per desi(each panel consisting of a single plank without joint and with ordinary glass of 7.4kg. Per sq.m./3mm thick) fitted with putty bed and teak wood beads and nails including fitting and fixing shutters in position but excluding the cost of glass, putty, teak bead, nails, hinges etc. and other fittings, in ground floor. 35 mm thick shutters with 19 mm thick panel of size 30 to 45 Cm. Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. Ground Floor 71 First Floor 72 Second floor 73 Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mmwide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan or similar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings in ground floor35mm thick shutters (single leaf) 74 Styles and rails of wooden shutters fitted and fixed complete. (Payment to be made on area of new work only). In Ground Floor :ii) 35mm Thick shutter. 75 First Floor 76 Second floor 77 Panel (made of single plank) of door and window shutters to design as directed: In Ground Floor (Payment to be made on area of exposed new work). (In case of non-supply of single plank penal rate of reduction to a maximum of 30% will be made).25mm thick panel of 30cm to 45cmSishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. 78 First Floor 79 Second floor 80 Easing door and windows. 81 Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)40mm X 6mm, 250mm Length 82 Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark.100mm. X 50mm. X 1.25mm. 83 Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws:75mm long x 10mm dia bolt 84 Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting.300mm long. 85 Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed With round base:100 mm grip x 10 mm dia rod. 86 Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. 87 Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. 88 Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :On timber or plastered surface :With super gloss (hi-gloss) - Two coats (with any shade except white) 89 On steel or other metal surface :With super gloss (hi-gloss) -Two coats (with any shade except white) 90 Uprooting and removing plants from the surface of walls parapet etc and making good damages. Repairing of damages to be paid separately. Small plant of girth of exposed stem upto 75 mm. lift upto 6 mtr. 91 Supplying, fitting & fixing UPVC pipes AType and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete.A) UPVC Pipes: 110 mm. Dia. 92 UPVC Fittings:Plain Tee110 mm. Dia. 93 Bend 87.5 degree110 mm. Dia. 94 Removal of rubbish,earth etc. from the working site and disposal of the same beyond thecompound, in conformity with the Municipal / Corporation Rules for such disposal, loading intotruck and cleaning the site in all respect as per direction of Engineer in charge 95 Supplying, fitting and fixing fibre reinforced polymer (FRP) Composite door frame as per approved section with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to safisfy IS: 4020 door testing performance criteria..ii) 66mm x 70mm 96 Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to satisfy IS:4020 door testing performance criteria. In ground floor. (i) 32 mm thick 97 Supply fitting, fixing cast iron down pipes conforming to IS:3989-1970 and IS:1729-1964 in position with necessary clamps, nails including making hole in wall, floor etc. and cutting trenches in any soil through masonry concrete structures etc. if necessary and mending good damages including joining with jointing materials complete. [ Payment will be made on centre line measurement of the total pipe line including specials. Payment for specials will however be paid separately ].(ii) 100 mm. Dia. (Internal) 98 SANITARY & PLUMBINGDismantling Orissa pattern W.C. including taking out of base concrete, if necessary, complete 99 Dismantling urinal. 100 Labour for dismantling G.I. pipe with fittings.15 mm 101 20 mm 102 25 mm 103 40 mm 104 50 mm 105 Refixing G.I. pipe with fittings after cleaning where necessary.15 mm 106 20 mm 107 25 mm 108 40 mm 109 50 mm 110 Removing chokage in G.I. pipe including cleaning pipe.15 mm 111 20 mm 112 25 mm 113 40 mm 114 50 mm 115 Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only).50 mm 116 40 mm 117 25 mm 118 Supplying, fitting and fixing bib cock or stop cock.Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). 119 Chromium plated Stop Cock (Equivalent to Code No. 513(A) & 513(B) & Model - Tropical / Sumthing Special of ESSCO or similar 120 Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand). 121 Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. 470 mm X 280 mm X 340 mm 122 Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding P or S trap (excluding cost of concrete for fixing). 580 mm X 440 mm 123 Supplying,fitting and fixing cast iron P or S trap conformimg to I.S. 3989 /1970 and 1729 / 1964 including lead caulked joints and painting two coats to the exposed surface. (Painting to be paid seperately).(B) S Trap (iii) 100 mm 124 Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver red as per I.S. 3438 / 1965 together with brass C.P. hinges.(i) 450mm x 300mm 125 Supplying, fitting and fixing towel rail with two brackets.(a) C.P. over brass(i) 25 mm dia. and 450 mm long 126 Supplying, fitting and fixing soap holder.(a) PTMT(Prayag or equivalent) 127 Supplying, fitting and fixing pillar cock of approved make.CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model - Tropical / Sumthing Special of ESSCO or similar brand). 128 Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.450 mm long 129 Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps.900 mm long 130 Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. 131 Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. (a) With P trap 132 Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete. (a) E.W.C.Plastic (hallow type) white 133 Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling,15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials. Pakur Varity. SAIL/TATA/RINL 134 Removing sludge from septic tank, soak well etc. by methor labour including disposal of the same outside the compound as directed Upto 50 users:-Within a lead of 150 metre 135 Supply of galvanised iron socket with I.S.I. mark.15 mm dia 136 20 mm dia 137 25 mm dia 138 Supply of G.I. plug15 mm dia 139 20 mm dia 140 25 mm dia 141 Supply of G.I. reducing socket with I.S.I. mark.20 mm dia 142 25 mm dia 143 Supply of G.I. bend.15 mm dia 144 20 mm dia 145 25 mm dia 146 Supply of G.I. plain equal elbow of approved brand and make.15 mm dia 147 20 mm dia 148 25 mm dia 149 Supply of G.I. plain tee of approved brand and make15 mm dia 150 20 mm dia 151 25 mm dia 152 Supply of G.I. reducing tee of approved brand and make20 mm X 15 mm 153 25 mm X 15 mm 154 25 mm X 20 mm 155 Supply of G.I. nipple standard 50 mm long. 15 mm dia 156 20 mm dia 157 25 mm dia 158 40 mm dia 159 Supply of G.I. union.15 mm dia 160 20 mm dia 161 25 mm dia 162 Supply of G.I. short piece of TATA make (Above 50mm & upto150 mm15 mm dia 163 20 mm dia 164 25 mm dia 165 Supply of G.I. reducing elbow.20 mm X 15 mm 166 25 mm X 15 mm 167 25 mm X 20 mm 168 Labour for fitting and fixing G.I. specials including cost of jointing materials.a) Plug.(i) Upto 25 mm dia. 169 (b) Socket, Reducing socket, Bend, Plain equal elbow, Reducing elbow, Nipple, Short piece.(i) Upto 25 mm dia. 170 (ii) Above 25 mm upto 50 mm dia. 171 c) Plain tee, Reducing tee, Pendent tee, Jamnut, Socket and Nipple. 172 (d) Cross, Union, Long screw.(i) Upto 25 mm dia. 173 Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992(A) (i) Single Socketed 3 Meter Length(b) 110 mmPVC Pipes100 mm dia 174 Renewing C.I. clamp for pipe including cutting hole in wall etc. and mending good all damages with cement concrete(4:2:1) with jhama chips and cement plaster (6:1) to match with and curing.100 mm 175 Supplying, fitting & fixing approved patent vent cowl I.C.I. conforming to I.S.S and painting two coats to the exposed surface with approved paint complete. (Payment of Painting will however be paid seperately).75 mm dia 176 Cleaning I.P.W.C. with acid. 177 Cleaning urinal with channel with acid. 178 Cleaning wash basin/ sink with acid. 179 Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately)(i) 15 mm dia. medium quality 180 (ii) 20 mm dia. medium quality 181 (iii) 25 mm dia. medium quality 182 (v) 40 mm dia. medium quality 183 (vi) 50 mm dia. medium quality 184 Supplying, fitting and fixing shower of approved brand and make.(a) (i) Chromium plated round shower with revolving joint 100 mm dia with rubid cleaning system (Equivalent to Code No. 542(N) & Model - Tropical / Sumthing Special of ESSCO or similar brand). 185 (a)(iii) Chromium plated shower arm 240 mm long (Equivalent to Code No.536(A) & Model - Tropical / Sumthing Special of ESSCO or similar brand). 186 (f) Hand Shower(Health Faucet) with 1mtr Fexible Tube with Wall Hook (Equivalent to Code No.573 & Model -ALLIED of Jaquar or similar). 187 Cleaning silt of inspection pit. 188 Cleaning soak pit by removing the top slab and replacing inner filling with jhama bats and repairing the pit as necessary including fitting the slab. 189 Wash basin vitreous china of approved make (without fittings) supplied,fitted and fixed in position on 75mm X 75 mm X 75 mm wood blocks and C.I. brackets including two coats of painting of C.I. brackets.(i) 450 mm X 300 mm size 190 Add GST @ 18% 191 Add Labour Welfare Cess@ 1%
