|
| 1 | Dismantling the Rein forced cement concrete cleaning away and carefully stocking materials usefull for reuse |
| 2 | Dismantling the Brick Masonry & RR Masonry incementmortorcleaning away at carefully stocking materials usefull for reuse for any thickness at well |
| 3 | Removing Exisiting door and windows including reused and frame, hinges etc |
| 4 | Earth work excavation for foundation by manual means for Isolated, Combined and Other type foundations in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers. |
| 5 | Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers -Mixing by mechanical means |
| 6 | Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require onlynominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener,side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid). |
| 7 | Providing and laying in position, Standardised Concrete Mix M-25 Grade by insitumachine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kglm3 and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m’) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials). |
| 8 | Ground Floor |
| 9 | Supplying and Fabrication of Steel and placing in position MS / Ribbed tor steel grills for RCC works as per design given including cost of steel and GI binding wire in Floors etc., Complete complying with standard specification in force per Kilogram. |
| 10 | Above Basement |
| 11 | Brick Work in Cement Mortor 1:5 Mix (one cement, five sand) using new best Second Class Bricks of size9 ” x 4 3/8 “x 2 3/4 ”from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications. |
| 12 | Ground Floor |
| 13 | Plastering with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 12mmthick mixed with water proofing compound conforming to BIS at 2% by weight ofcement used including mortar plasticizer at 200ml per 50Kg of cement used, finsihing, curing, etc., complete in all floors complying with standard specification and asdirected by the departmental officers. |
| 14 | Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand),12mmthick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curingetc. complete complying with standard specification and as directed by the departmentalofficers. |
| 15 | Painting New Plastered Wall Surface with Two finishing coats of ready mixed(Emulsion) of approved quality and colour over one coat priming coat in all floorsincluding the cost of primer etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should begot approved by the Executive Engineer before use on works.) |
| 16 | Flooring with ceramic tiles of following size and variety conforming to IS 15622 laidover cement mortar bed of 20 mm thick in cement mortar 1:3 (One Cement and Threecrushed stone Sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 17 | Plastering with Cement Mortar 1:3 (One Cement and Three Plastering Sand)20mmthick mixed with water proofing compound conforming to BIS at 2% by weight ofcement used including mortar plasticizer at 200ml per 50Kg of cement used, finsihing,curing, etc., complete in all floors complying with standard specification and as directedby the departmental officers. |
| 18 | Dadooing walls with following best approved quality, white / colour glazed tiles conformingto IS 15622 of following sizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant TileEpoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use onworks) |
| 19 | Paving the floor with best quality vitrified Tiles of following size and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laidover cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and threecrushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors andthe top pointed with Water Resistant Tile Epoxy Grout etc., complete complying withstandard specification and as directed by the departmental officers. (The make and brandof the tiles should be got approved by Executive Engineer before use on works) |
| 20 | Supply and fixing of Solid PVC door shutters with frameusing 19 guage 19mm Ms square tubes for styles and outer frame 15mm MS square tubes for top lock bottom rails. The steel square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutterrs using 5mm thicksolid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. the overall size of styles shall be 50mm x 30mm. the overall size of top rail, lock rail and bootom rail shall be 75mm x 30mm. the ovrall size of frames shall be 50mm x 45mm with suitable rebate for housing the shutters. etc., complete complying with standard specification (PWD SOR 2022-23 P.No.43) |
| 21 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work |
| 22 | Painting new iron works such as steel doors, windows, ventilators, window bars,balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost ofpriming coat etc., complete complying with standard specification and as directed by thedepartmental officers. (The make, quality and colour of paint should be got approved bythe Executive Engineer before use on works.) |
| 23 | Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A FT switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed light point / fan point (for electronic regulator)(SD No :23) |
| 24 | Supply and fixing of 1400 mm sweep (56\") AC ceiling fan complete with step pedelectronic 300W regulator with 1 metre down rod including fan clamp with side plates and cross arm of size 450mm (SD No :108) |
| 25 | Supply and fixing of 4\"40W twin box type fluorescent fitting complete with copper choke and condensor with TW round block on wall or ceiling with tubes and PVC unsheathed FRLS copper leads from terminal to the fitting with fluoresent tubes (SD No:90) |
| 26 | Supply and fixing of fancy glass shade and 7W / 9W LED bulb (SD No:80) |
| 27 | Supplying and fixing in position best quality PVC soil / waste pipes of various dia having6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level |
| 28 | 110mm dia Pipe |
| 29 | 75mm dia Pipe |
| 30 | Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with “P” or “S” trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works). |
| 31 | Supplying and fixing in position best approved of BIS quality PVC rain water down fallpipes having a pressure of 4 kg. / sq.cm including cost of neceSORy PVC shoe, PVCbend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab includingfinishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of “U” clamp at the centreof the pipe line in addition to those for more than 3.0 metre pipe length, etc., completecomplying with standard specification and as directed by the departmental officers |
| 32 | Supply and fixing in position 15mm dia brass CP screw down tap/pillar tap (heavy duty) of approved make confirming to BIS Specifications and quality including cost of shellac thread etc complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works) |
| 33 | SD Tap |
| 34 | Pillar Tap |
| 35 | Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works). |
| 36 | PVC Elbow |
| 37 | 110mm dia |
| 38 | 75mm dia |
| 39 | PVC Elbow with Door |
| 40 | 110mm dia |
| 41 | 75mm dia |
| 42 | PVC Tee |
| 43 | 110mm dia |
| 44 | 75mm dia |
| 45 | PVC Tee with single door |
| 46 | 110mm dia |
| 47 | 75mm dia |
| 48 | PVC \"Y\" with single door |
| 49 | 110mm dia |
| 50 | 75mm dia |
| 51 | Supplying PVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements |
| 52 | Coupler |
| 53 | 25mm dia |
| 54 | 32mm dia |
| 55 | Elbow |
| 56 | 25mm dia |
| 57 | 32mm dia |
| 58 | Bend |
| 59 | 25mm dia |
| 60 | 32mm dia |
| 61 | Tee |
| 62 | 25mm dia |
| 63 | 32mm dia |
| 64 | End Cap |
| 65 | 25mm dia |
| 66 | 32mm dia |
| 67 | Reducer |
| 68 | 20mm x 15mm |
| 69 | 25mm x 20mm |
| 70 | 32mm x 25mm |
| 71 | Reducer Tee |
| 72 | 20mm x 15mm |
| 73 | 25mm x 20mm |
| 74 | 32mm x 25mm |
| 75 | Reducer Elbow |
| 76 | 20mm x 15mm |
| 77 | 25mm x 20mm |
| 78 | 32mm x 25mm |
| 79 | Jet Nipple |
| 80 | 25mm dia |
| 81 | 32mm dia |
| 82 | Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls,etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work. |
| 83 | 25mm Gun Metal Gate Valve |
| 84 | 32mm Gun Metal Gate Valve |
| 85 | Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works) |
| 86 | Supplying and fixing of 1000 Liters capacity HDPE tank with IS specification IS 10701/96 the tank is meant for outdoor (or)indoor use complete with removable hinged top locking arrangement and to make provision to fix water supply pipe lines, necessary man hole with cover and including all PVC specials pugs, screws nails to fix the tank etc., complete and the tank should fixedfirming as directed by the departmental officers.The rate shall be inclusive of all materials, labour conveyance hoisting and fixing charges etc. (The water tank should be got approved by the EEbefore use on work. |
