Tender For Special Repair To Bldg No T-26 Of Sajjan Lines At Udaipur Mil Stn; 1 Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level andremovingmaterial from site complete all as specified and directed.(for one roomflooring & plinth protection) 2 Material and Labour for PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in sub base/levelling coarse and finished the top surface even and fair complete all as specified. 3 Material & Labour for 75 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished complete. Note : Joints 12 mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection. 4 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed. 5 Material & Labour for Coloured Ceramic tiles 8 to 10 mm thick (square/rectangular) size of 600x600 mm ,in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed incement mortar 1:6 complete all as specified and directed. 6 Material & Labour for Coloured Glazed ceramic tiles in vertical surface300mm X 600 mm X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to matchincluding 10mm thick cement plaster in ement mortar 1:4 as backing coat on fair faces on stone surface all as specified and directed. 7 Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. all complete as specified and directed.(For Entrance Verandah only) 8 Material and labour for machine cut Prepolished Kota stone slab 20-25 mm thick (of size not less than 55 cm x 55 cm in flooring and 120 cm x 25 cm in treads) laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including half round edge moulding, over and including cement screed bed 15 mm thick in cement mortar (1:6) baseincluding rubbing and mirror polishing, and half nose moulding (bull nosing) etc,complete all as specified. 9 Material and labour for mirror polishing of existing Kota stone in flooring , skirting, riser and treads etc with and including grey cement slurry mixed with pigment to match shade of kota stone wherever as required complete. 10 Material & Labour for marble work (Bhaislana Zebra Black) 18 to 20mm thick (table rubbed and polished) in window cills ,in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types and including 10 mm thick screed bed in CM 1:6set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces and half nose moulding (bull nosing) etc, complete all as specified and directed. 11 M&L for Polishing of shutters and frameswith approved wood polish (Melamine/PU/French Polish as specified) to exisiting seasoned wooden windows (including glass panes) in original position ,including minor repairs (like filling cracks,tightening joints),cleaning or replacing damaged glass panes, fixing with new hardware (hinges,stays,handles,screws), realignment for smooth operation ,and final cleaning; all complete as specified and directed by Eng-in-charge.(Note : Windows size - 1.0 x 1.20 m Approx.) 12 Taking down wooden chowkats or frames area exceeding 1.50 Sqm andnot exceeding 4.00 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and as directed. 13 Supplyand fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 65 mm x 125mm(moulded) having Double rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by Rajshri/Echon or Eq an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company. 14 Supplyand fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 50 mm x 100 mm(moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by Rajshri/Echon or Eq an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company. 15 S&FFactory made single extruded WPC (wood polymer composite) soild decorative type Moulded door shutter of size 30 mm thick material comprising of virgin PVC polymer of K-Value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives(maxiumum toxicity index of 12 for 100 gms)having minimum frame density of 650 Kg/cbm & manufactured by Rajshri/Echon or Eq an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 1800N(face) & 900 N(edge),) Minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter& fixed with SS butt hinges of required size with necessary full body threaded star headed counter sunk SS screws complete all as specified and directed. 16 Supply and fixing IInd class (hollock) hard wood factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed. 17 S&FFactory made single extruded WPC (wood polymer composite) soild decorative type Flush door shutter of size 30 mm thick material comprising of virgin PVC polymer of K-Value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives(maxiumum toxicity index of 12 for 100 gms)having minimum frame density of 650 Kg/cbm & manufactured by Rajshri/Echon or Eq an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 1800N(face) & 900 N(edge),) Minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter& fixed with SS butt hinges of required size with necessary full body threaded star headed counter sunk SS screws complete all as specified and directed. 18 Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed. 19 Supply & fixed150 mm long Extruded aluminiumalloy handles, fabricatedtype anodised complete all as specified. 20 Supply & fixed100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed. 21 S&F alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified. 22 S&F double legged door stopper of overall length of cover plate 150 mm of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floors and rubber all as specified and directed by Engr-in-charge. 23 Supply & fixedMS helical door spring 300 mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats. 24 Supply & Fixedin repairs aluminium Hat and coat hooks, solid body, 175mm to 250 mm 25 Supply & fixedin repair stainless steel wire cloth,0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples. 26 Dismantling structural steel work including doors, gates but excluding framedtruss etc.all complete as specified and directed . 27 Supply and fixing for mild steel framed work as in cooler stand, gate doorsas in fixing by drilling/cutting the stone masonry wall and fixing for particle board & other section of grade Fe-290-Gde E-165 with gusset plate rails, braces etc welded/drilled to fixing of steel sheeting or other covering doors etc. to be prepared for sliding or hanging with and including either hooks and hinges or steel hanging door fittings (exclusive steel sheeting or other covering, running rails & guides), complete all as specified and as directed by the Engr-in-Charge. 28 Supply & fixing in repairs stainless steel type curtain rod 22 to 25mm dia as per sample 29 Supply & fixedin repair of purpose made brackets trade pattern for stainless steel decorative type curtain rods suitable for holding 22 to 25mm dia as per sample as in repair. 30 Supply & fixedin repair of stainless steel decorative fincals(round type with mirror optic finish)trade pattern for decorative type curtain rods suitable for 22 to 25mm dia curtain rods as per sample as in repair complete all as specified. 31 Material and labourfor suspended false ceiling system using Chicago Metallic (E-grid) exposed suspended system, grid size 600mm x 600mm comprising of GI poweder coated main dunner fo dimensions 39mm x 24mm xx 0.8mm thick (thickness comprising of GI/0.4mm +PPPCGS/0.3mm & weight of runner 1.35 Kg for 3600mm length), cross tee of dimensions 29mm x 24mm x 0.8mm thick (thickness comprising of GI/0.4mm + PPPCGS/0.3mm & weight of Tee 0.195 Kg for 600mm length) and wall angle of dimensions 22.2mm x 22.2mm x 0.65mm thick (thickness comprising of GI / 0.35mm + PPPCGS/.3mm & weight of angle 0.70Kg for 3050mm length) with and including 4mm thick HPSC (High pressure steam cured) pre-primed, self embossed, tentured designed board to be placed in the grid system duly suspended with 4mm dia GI wire hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt-0.007 kg/clip), hold down clips (wt-0.0035 kg/clip), with provn of light fixture complete all as per manufacturers instructions and as directed. 32 Dismantling wooden boarding, any description, fixed in any position with nails including of any size including tilting fillets sapced exc 15 cmall complete as specified and directed. 33 M&L For Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings all complete as specified and directed. 34 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steelsheet 0.50 mm thick of an colour having tensile strength of 550 Mpa (150 AZ) as inroof covering/cladding to wall, fixed with self tapping screws as specified and directed. 35 S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet0.50mm thick of any colour having tensile strength of 550 Mpa (150 AZ) as in roof covering/cladding to wall, fixed with self tapping screws as specified as and directed. 36 Taking down cement plaster from brick walls/stone masonry walls, concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed. 37 Material andlabour for 10 mm thick rendering in cement mortar (1:6) onbrick/stone masonry or concrete surfaces (internal walls) of any description, finished the surface even and smooth without using extra cement complete all as specified. 38 M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of primercomplete all as specified and directed. 39 M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper (acrylic) white or tinted wallscomplete all as specified and directed. 40 M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of Cement Based Paint white or tinted wallscomplete all as specified and directed. 41 M&L for two coat of synthetic enamel painting to new steel surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of red oxide primer complete allas specified and directed. 42 M&L for One coat of synthetic enamel painting to old steel surface of any description, not otherwise described over 10cm width or girth including preparation of old steelsurfaces complete allas specified and directed. 43 Demolition of Brickwork or stone/ boulder masonry, built in Cement mortar including all quoins, arches, pillars, etc,complete allas specified and directed. 44 Material andlabour for 15mm thick rendering in cement mortar (1:6) onbrick/stone masonry or concrete surfaces (External walls) of any description, finished the surface even and smooth without using extra cement complete all as specified. 45 M&L for preparation of newly plastered surfaces of wall and applying two coats of Cement Base Paint white or tinted over a coat of primercomplete all as specified and directed. 46 M&L For Providing precast cement concrete louvres and jallies, 25mm thick (measured solid), including all mould- ings set in C:M (1:6) ,Type B0 1:2:4 (12.5 mm graded aggregate ) fixed to brick masonery walls all complete as specified and directed. 47 Supply & fixedPolymer coloured (Polypropeylene Delrin and ABS) low levelflushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets, rawl plug, brass screws handle etc complete having BIS derscriptionmark with 2731 with andincluding suitable size of MS brackets, plug, screws all as required incl taking down existinghigh level/low level flushing cistern any type disconnecting pipes and jointingwith new one etcand making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed. 48 Supply and fixing in repairs Vitreous ChinaW.H.B. white oval type counter below type of size 550 x 400 mm including waste coupling, waste pipe and brackets etc. complete all as specified. 49 Supply and fixing in repairs vitreous china premium quality/1st quality wash down water closet pan (pedestal pattern), white (excluding flushing cistern & flush pipe) &incl 01 No ‘P’ or ‘S’ trap of dia 100mm includingprovn of lime concrete bedding, complete all as specified. 50 Supply andfixing in repairs,15mm bore pillar tap, fancy type, chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks , compete all as specified. 51 Supply andfixing in repair, bib tap screwed down high pressure, cast copper alloy,fancy type, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified. 52 Supply andfixing (in repair) angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified.(Note : Weight of cock shall not be less than 0.575kg) 53 Supply & fixedin repair PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified. 54 S&F in repair 15mm bore concealed stop valve type chromium plated cast copper alloy screwed down high pressure screwed both ends for iron pipe or for unionall as specified and directed by Engr-in-charge. 55 S&F in repair brass chromium plated tubular towel rail 20mm dia D type 60cm long between flanges all as specified and directed by Engr-in-charge. 56 Supply and Fixing in repair rotational molded polyethylene water storage tanks white tripple layered (cylindrical vertical with closed top) capacity 1000 Ltrhoisted and fixed in position including dismantling water tanks including disconnecting all necessary connections ofwater tanksall as specified and directed by Engr-in-charge. 57 S & F in repair gun metal globe/gate valves, with iron wheel head, screwed both ends for iron pipe flange ends type fixed of 20mm dia all as spd and directed. 58 S&F in repair PTMT float ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipesall as specified and directed by Engr-in-charge. 59 Supply & fixedin repair 1500 mm x 600 mm beveled edge mirror of selected quality glass mounted on 5.5 to 6 mm thick PVC sheet board & decorative teakwood beading all around including polishing and fixed to wooden plugs with CP brass screws and cup washers. 60 Taking up or down steel tubing and connections of 15mm bore including cleaning for refixing or removal to store provision for branch connection by inserting tee union elbow etc. complete all as required at site. 61 All as item above but 20mm bore, complete all as specified. 62 Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 16mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the entire satisfaction of Engineer-in-charge. 63 Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 20 mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the entire satisfaction of Engineer-in-charge. 64 Supply & fixed in repairs stainless steel grating openable 100mm dia without hole including fixing with white cement complete all as specified. 65 Supply & fixed in repairs stainless steel grating openable 100mm dia with hole including fixing with white cement complete all as specified. 66 Supply & fixedin repair fancy type shower rose125mm dia sizeof Rim and 30cm long CP brass pipe with swiwel joint complete all as specified. 67 Supply & fixedin repair glass shelf assembly consisting of made out of 5.5 mm thick glass shelf 12 cm wide with chromium plated bracket guard andrailing 60cm long complete all as specified and directed. 68 Supply & fixedin repair for CP brass Soap Dish Holder, complete all as specified and as directed. 69 Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortarand taking out complete all as specified and directed. 70 S&F 110mm dia UPVC (SWR) type B pipe single sockets in any length with rubber ring joints, laid in trenches or in floor complete all specified and directed. 71 S&F 110mm dia UPVC (SWR) type B pipe single sockets in any length with rubber ring joints, fixed to wall complete all specified and directed. 72 S&F 75mm dia UPVC (SWR) type B pipe single sockets in any length with rubber ring joints, laid in trenches or in floor complete all specified and directed. 73 S&F 110mm dia UPVC (SWR) bends any radius including cutting of holes. 74 S&F 75mm dia UPVC (SWR) bends any radius including cutting of holes. 75 S&F 110mm dia UPVC (SWR) branch piece single (single Y) equal or unequal. 76 S&F 75mm dia UPVC (SWR) floor trap, plain with grating including jointing with solvant cement complete all specified and directed. 77 S&F UPVC (SWR) gully trap 125/110 mm setting and jointing with solvant cement complete all as specified and directed. 78 S&F UPVC (SWR) vent cowl 110 mm bore setting and jointing complete all as specified and directed. 79 Taking down old unserviceable copper/aluminium point wiring (light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling rose, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. all as directed by engineer in charge. 80 M&L for point wiring with 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated, FRLS and unsheathed type alongwith 1.5 Sqmm PVC insulatedstranded copper conductor cable for continous earthing in & including PVC rigid conduit concealed on stone/brick masonrty wall surface with accessories having ISI mark fixed on wall surfaces / ceilingincluding provision of PVC box of appropriate size for fixing switches sockets etc. all as specifiedfor One light point / Fan/ bell point controlled by one switch. 81 (a) One light point controlled by one switch with cables 1.5 sqmm size. 82 (b) One fan/ exhaust fan point controlled by one switch with cables 1.5 sqmm size. 83 (c) One 3 pin socket outlet, 5 amps on the same board with other switches, with cables 1.5 sqmm size. 84 (d) One 3 Pin socket oulet 5Amps on indepndent, with cables 1.5 Sqmm size 85 (e) One light point controlled by two 2 - way switches, with cables 1.5 sq.mm size. 86 (f) One 3 Pin 15A pin socket oulet 15Amps on indepndent board with cables 4 Sqmm size 87 S&F switch piano flush type single pole one way 5/6 Amps. 88 S&F lamp holder, PVC/Polycarbonate typewith back plate suitable for batten fittings including dismantling old one. 89 S&Fsocket outlet 5 pin 5/6 Amps flush type multipurpose suitable for 3 pin/2 pin plug complete includingdismantling old one. 90 S&F ofswitch piano 15 Amp 230 Volt, flush button single pole one way complete all as specified and directed by Engr-in-Charge includingdismantling old one. 91 S&F socket outlet 2 in 1, 3 pin 5/6 Amps and 3 pin 15/16 Amps flush type including old one. 92 S&F ceiling rose surface tpe 3 terminals to be fixed on PVC block includingdismantling old one. 93 S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd. 94 S&F switch piano flush type single pole 16 Amp 2 Way . 95 S/F LED integrated batten tube light fittings 20W 4 Feet long complete up with twin core twisted flexible copper conductor cable of size 23/0.0076 complete all as specfied and directed. 96 Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. 97 M&L MCB SPN DB comprising of sheet metal enclosure single door suitable for mounting MCB 240 Voltswithbusbar 200 amps rated8 way includingdismantling old one. 98 S&F RCBOs Double pole, 30mA 32 Amp rating for earth leakage, overload & short-circuit protection. 99 Supply and fixing SPN 32 Amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning. 100 Supply and fixing SP 6 to 32 Amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning. 101 Taking down carefully, deposited to MES store and hanging only ceiling fan & Exhaust Fanand connecting up including provision of cable from ceiling rose or connector to fan complete all as specfied and directed. 102 Excavating in trenches n.exc 1.5 m widthand n.exc 1.5m in depth for taking out cable and cable coverand getting out in any type of soil 103 Returning, filling in, including spreading levelling, watering and well ramming in layers n.exc 25 Cm. 104 Removing excavated materials n.exc 50 mtr depositing where directed at a level n.exc 1.5 m above the starting point 105 M&L for spreading, levelling in layers n exc. 25 cm thick and ramming of sand cushioning to PVC/ XLPE cables with tibba sand and punning to provide required cover to UG cables.Note :- For the purpose of payment only punned thickness will be measured. 106 Supply and laying reinforced precast concrete cable cover, class LV,type 1 flat, 250mm x 150mm x 40mm. 107 Material & labour for taking out old GI Pipe 50mm dia from trenches and removing from site 108 Supply and fix medium grade50 mm dia GI pipe fix complete to wall , poles etc with suitable clamp for protection of cable complete all as directed. 109 Supply, laying and testing cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of size25 sq mm 3.5 core. 110 Material & labour for earthing complete with galvanised steel earth plate electrode 60x60cmx6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below the ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level, connected to galvanised earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or of steel all as shown in electrical plate No 3 of SSR part-I2009 connected to main switch board all as specified and testing on completion including. Necessary excavation, earthwork, PCC works and CI earth pit cover with watering pipe 20mm dia GI pipe medium grade, funnel with wire mesh and lugs and GI pipe 15 mm dia of light grade,for protection of earth leadcomplete all as specified and directed. 111 S&F Submain wiring alongwith earth wire with the following sizes of 2x2.5 sqmm + 1x2.5sqmm earth wire FR PVC insulated copper conductor, single core cable in surface/recessed as required.Note : Two run of 2.5 sqmm cable with colour code of R, Y & B for phase/ neutral and one run of same size cable with Green colour as earthing for socket point alongwith required PVC conduit and connected items will be measure as one RM. 112 S&F Submain wiring alongwith earth wire with the following sizes of 2x4.0 sqmm + 1x4.0 sqmm earth wire FR PVC insulated copper conductor, single core cable in surface/recessed as required.Note : Two run of 4.0 sqmm cable with colour code of R, Y & B for phase/ neutral and one run of same size cable with Green colour as earthing for socket point alongwith required PVC conduit and connected items will be measure as one RM. 113 M & L for scrapping out old rusted and corroded sufaces to making good surface of iron body/CRCA sheet main DBs of any shape & size for external and internal surface and preparing the exposed surfaces & applying two coat of aluminium paint paint over a coat of red oxide zinc crome primer complete all as specified and directed. 114 S&F LED security light luminaries of 35 watt for energy saving having IP-65 degree of protection made of pressure die cast aluminum housing and heat resistant thoughned glass with excellent thermal management, LEDs should have better optics and uniform distribution of light including GI tubing 40mm dia light grade 1.2 mtr long pipe bent to shape 120 degree for mounting of security light and fixed to wall/pole, with suitable MS clamps 2 Nos with nut and bolt and washers including connecting complete including 2.5 sqmm stranded copper conductor of suitable length as per direction and approved by Engr-in-charge, 115 Material and Labour for Testing of water from approved Govt lab samples collected from pump house No-01 at main Gate as per norms of WHO and submission of test reports to the entire satisfaction of Engineer-in-Charge, the test report includes following parameters:- PH value, TDS(mg/l), Hardness (as CaCO3) (mg/l), Fluoride (mg/l), Chloride (mg/l),Turbidity (NTU), E.Coli (cfu), Free residual Chlorine
