Tender For Special Repairs To Jcos Married Accn Block No P74 02X Quarter At Suranussi Under Age I Suranussi; 1 Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles 2 Demolition of cement concrete of any description and in any position (above /below of ground level) not otherwise specifically provided as in sunken floor , plinth protection, foundationetc. 3 Taking down cement or cement lime plaster of any description from walls, including racking out joints hacking for key scrubbing down with water etc , complete all as specified & directed. 4 Taking down chowkats or frames with Shutters( without taking off the shutter from the frame ) of area n.exc 1.50 Sqm each including iron mongery and removing from site. 5 All as perItem No 4 above but area exc 1.50 Sqm but n.exc 4.00 Sqm each. 6 Taking down shutter only of any desription of size exc 1 sqm and n.exc 2sqm. 7 Taking down shutter only of any desription of size exc 1 sqm and n.exc 2 sqm but refixing in the same opening 8 M&L for brick work , with sub class B bricks built in cement mortar 1:6 straight or curved on plan exc 6mtr mean radius with old size bricks complete all as specified. 9 All as per description of item No 8above but except brick. 10 M&Lfor 15mm thick cement plastering in cement mortar (1:6) on other than fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement, complete all as specified & directed. 11 M&L for 15 mm thick cement plastering in cement mortar (1:4) on fair faces of brick work or concrete surfaces mix with water proofing compound as per manufacturers instruction,finished even & smooth without using extra cement complete all as specified and directed. 12 M&L for 5 mm thick rendering in cement mortar1:3 on ceiling ofRCC slab, complete all as specified & directed. 13 M&L for preparation of affected concrete and steel surface as in ceiling of roof slab, beams & chajjas by cleaning with metallic wire brush scrupulously and carrying out the following operations step wise :-(a) Applying rust remover solution on steel bars by using cotton waste swab or by brush and leave the surface for 15-30 minutes. Remove the loose rust particles by scrubbing with brush and wash the steel surface with water.(b) Apply red oxide primer over cleaned steel surfaces. Apply epoxy bonding agent (adherent solution) over cleaned dust freed old concrete surface. Apply polymer mortar with the help of trowel in single or multilayer as an when required during application and finishing the surface even and smooth.Notes :- (a) The bars which are corroded badly need to be strengthen by placing new bars by means of welding withproper splice length and will be measured and paid separately under appropriate item. The rate of item includes necessary formwork, shuttering, scaffolding, staging etc all as specified and directed by Engineer-in-Charge. 14 S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering to Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to GdeFe 290(Gde E-165), complete all as specified and directed. 15 S & F 1 mm thick Mild steel, plain, black sheetfactory made, cup board shutters with necessary angle iron frame including all fittings i.e mortice lock with handle ,butt hinges peg set etc including two coats of spray painting over a coat of red oxideetc. as required, complete all as specified and directed. 16 S&F 35 mm thickflush shutter solid core constructionwith block board core and plywood face panels commercial face on both faces including both face is covered with decorative face veneer with lipping/frame as required, complete all as specified anddirected 17 M&L for 35mm th IInd class HW glazed /gauged shutters open rebatd and prepared to receive glass /gauge etc without sashbars edges of framing plain or chamfered, rounded fitted with cut and mitred beads for securing glass/gauge etc,size of members of shutters as specified in SSR Part-I section 8 clause 8.24 (a), complete, all as specified anddirected. 18 S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat /Frame size 65x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. 19 M&L for providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type/moulding typeflush door shutter of size30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 20 S & FAnodised aluminium frame Powder Coating (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified & directed. 21 S & F for Anodised aluminium window and ventilator shutters, Powder Coating (minimum thickness of powder coating 50 micron) fixed type without sash bar, hook and eye closure Each door having 02 Nos D type handles, 02 Nos aluminium tower bolts 300 mm size,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified 22 S & F for Anodised aluminium window and ventilator shutters, powder coating (minimum thickness of powder coating 50 micron) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats,hook and eye closure, each door having 02 Nos D type handles, 02 Nos aluminium tower bolts 300 mm size, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified & directed. 23 S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 100 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening,complete, all as per requirement and direction of Engineer in- charge. 24 S & F 4.8mm thick glass sheet ordinary quality glazing fixing in aluminium frame black or transparent in square n.exc0 .5 sqm in each pane, complete, all as specified and directed. 25 S&FStainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete, all as specified and directed. 26 M&L18/19 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white laminationandfixed with screws to timber frame work . 27 S & Fauto closing hinges 50 mm size of 0 crank OR8 crank openable at 110 degree for kitchen cabinet shutters, of stainless steel grade SS-304, bright finish or electro galvanised complete as approved by GE.Make: Kaff / Hettich / Hafele/ Godrej 28 S&F Continous (piano) hinges, stainless steel , bright finishor electrogalvanised, width of flap 40mm,complete all as specified and directed. 29 S&F stainless steel handles 125 mm size for kitchen cabinet shutters/ cupboard complete all as specified and directed. 30 S&F magnetic catcher of size 20mmx50mm suitable for kitchen cabinet shutters/ cupboard, complete all as specified and directed.Make: Kaff / Hettich / Hafele/ Godrej 31 S & F Ball bearing runners 50 mm size Telescopic full extension load capacity 50 kgs, of stainless steel grade SS-304 complete as approved by GE.Make: Kaff / Hettich / Hafele / Godrej 32 S&F 300mm size stainless steel sliding door bolt plate type stove enamelledblack with bright bolt not less than 12mm diaincl a minimum of six nut and bolts ,four on bolt plate and two on staple plate complete all as specified & directed. 33 S&F steel locking bolts with mild steel electrogalvanised plate and bright bolt not less than 10mm dia 100mm size etc all as specified & directed. 34 S&F 150 mm size stainless steel pressed handles, oval type, stove enamelled blackall as specified and directed by Engineer-in Charge 35 S&F 100 mm sizebutt hinges of cold rolled mild steel, medium weight, complete, all as approved and directed. 36 S&F floor door stopperaluminiumalloy body and tounge 140mm anodised with hard drawn steel spring etc,complete all as approved and directed. 37 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), rmoving servicable tiles to store and rubbish off the premises, complete all asdirected. 38 S&F 300mm size mild steel rat rail rod pattern spring including roller and roller plate complete all as approved and directed. 39 M&L for Granite (of any type) work (table rubbed and polished) 20 mm thickin steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including screed or bedding layer 20mm thick in CM 1:4 all as thicknessof screed specified. 40 M&L for virified ceramic tiles ofdark shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over andincluding 15 mm thick screed or bedding layer in CM 1:6 complete all as specified and directed. 41 M&L for glazed ceramic coloured tiles on vertical surface 450 x350 x 7mm thick set and jointed in neat cement slurry pointed in white or colour cement to match the colour, with and including 10mm thick cement screed bed in cement mortar (1:4) complete all as specified and directed. 42 S&F in repair vitreous china squatting pan ‘Orissa patten’ size 580x440mm white with intergral foot rest (excluding flushing cistern and flush pipe)with P or S trap including water connection to trap and flushing pipe, flushing cistern etc incl lime concrete bedding and PCC 1:2:4 for making good the floor fixed in repair complete all as specified & directed. 43 S&F in repair PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32mm bore, connection to WC pan & PVC connection 15mm size with PTMT nuts of length 300mm complete all as specified & directed . 44 S& F vitrious china wash hand basin flat back550X400mmincluding padestal withfixing bracket, PVC waste coupling , CP grating and waste pipe, 15mm CP pillar cock swan neck etc, complete, all as specified and directed. 45 S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers etc, complete, all as specified and directed. 46 S&F in replacement 20 mm dia harrison rails mild steel with decorative finish , with fixing brackets , stops, rollers complete all as specified and as directed .(Two brackets per 1.5 M length and 08 Nos roller per 1.RM) 47 Dismantling brick tile or terracing tile single layer on roof, all as directed. 48 Demolition of mud in roofs ,any thickness including plastering and leeping (weather full thickness removed or part thereof all as specified and directed. 49 Demolition of cement Concrete of any description and in any position not otherwise specifically provided for, complete, alldirected. 50 Supply only Integral waterproofing compound, ISI marked. 51 M & L for repairing of RCC projections , chajjas, roofs,facia, etc.by necessary preparations i.e.scrapping cutting,chiseling,dusting and cleaning exposed reinforcement ,surface of damaged,loose RCC surface and applying one coat of cement slurry and filling the surface with cement cencrete (1:2:4) using 12.5mm garded crushed stone aggregate and finished with cement sand mortar (1;3) using coarse sand in patches, area n exc 5 sqm each and thickness of RCC member exc 50mm including applying two coats of finishes to match with the bexisting surface in at any height, complete, all as directed by Engineer-In-Charge Note :Cost of form work for bldg ht upto 12m ,shall be deemed to be included in unit rate quoted by the contractor. 52 Applying evenly a tack coat of industrial bitumen 85/25 at the rate of1.2 kg per sq.m including cleaning surfaces 53 M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (weight not less than 150 gms/sqm) laid on primed surface by torch application complete all as specified & directed. 54 M&L for 75mm thick PCC 1:3:6 type C-2 as in plinth protection finishing the surface even and smooth without using extra cement laid to a slope of 1 to 20.It shall be laid in alternate bays, each bay not exceeding 3 m in length with joint to be filled with bituminous mastic filling comprising of mixture of one part of heated hot blown bitumen 85/25 penetration and three parts of heated sand all as specified & directed. 55 M&L for Cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed with grey cement and pigment; set jointed and pointed in neat cement slurry in floors, and cut and polished with WPC and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement and pointed in CM (1:3)complete all as specified and as directed. 56 M&L for 75 mm(average consolidated thickness) PCC 1:3:6 type C2using 20mm graded stone aggregate as in padding on flat roofs etc, complete all as specified & directed. 57 M&L forProviding, cement concrete type B-0 1:2:4 (12.5 mm graded aggregate ) asin roof kerbs or mud stops, rounded or chamfered on edges parapets copings, bed plates, etc complete all as specified & directed. 58 Cutting groovesof size 75mm wide and 65mm deep in brick parapet wall for inserting APP membrane and making good the disturbed portion in CM (1:3) etc complete all as specified & directed. 59 Dismantling water tanks of any description exc 250 and n.exc 500 ltr capacity. 60 S&F Rotational moulded polythene water storage tanks triple layer (cylinder each vertical with closed top) of capacity 500 Itrs, hoisted and fixed in position including pvc float valve 20mm size,specified in SSR Pt-1. 61 Taking up/ down GI tubing and connections with all fittings 15 mm bore. 62 Taking up/ down GI tubing and connections with all fittings 20 mm bore. 63 S&F 15 mm dia GI water tubing , medium grade with all fittings,fixedto wall and ceiling or laid in floors including making hole in RCC slabs for vertical pipes & making goods the same with cement concrete 1:2:4 including laid in floor etc complete, all as specified and directed. 64 All as per item No 63 above but fixing only. 65 S&F 20 mm dia GI water tubing , medium grade with all fittings,fixedto wall and ceiling or laid in floors including making hole in RCC slabs for vertical pipes & making goods the same with cement concrete 1:2:4 including laid in floor etc complete, all as specified and directed. 66 All as per item No 65 above but fixing only. 67 M&Lfor Cutting chases not exc 10 cm girth , pinning in, making good to facings wherever required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring etc. and making good, Complete, all as directed. 68 S&F in repairCP shower rose 15mm size fixed to iron pipe . 69 S&F PVC connection 15mm size with PTMT nuts of length 450mm, complete, all as directed. 70 S&F in repair for chromiumplated central hole basin mixer 15mm size for mixing hot & cold water for WHB complete all as specified and directed 71 S&F in repair 15mm CP Bib taps long body ,cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete, as directed. 72 S&F in repair 15mm size brass stop valves/angle valve with crutch or butterfly handles high pressure screwed both endsfor iron pipe, complete, all as directed. 73 S&F in repair fancy type stop cock cast copper alloy screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipe chromium plated with long shank(concealed type) for 15mm bore pipe. 74 S&F in repair 20mm size stop valves PTMT high pressure screwed for iron pipe, complete. (Minimum weight 92 gms) 75 S&F in repair Tubular towel rail600mm longof PTMT fixed with and including Chromium plated brass screws and wooden/plastic, cleats (Minimum weight 190 gms), complete all as directed by Engr-In-Charge. 76 Dismantling wrought iron or mild steel work of any description not otherwise provided for, as directed. 77 M&L for preparing new surfaces ofwalls and applying two coats of oil bound distemper over a coat of alkali primer over and including a finished coat ofwall care putty to achieve smooth finish, complete, all as specified & directed. 78 M&Lfor complete removal of existing treatment of wall and preparing old surfaces ofwalls and applying two coats of oil bound distemper over a coat of alkali primer over and including a finished coat ofwall care putty to achieve smooth finish, complete, all as specified & directed. 79 M&Lfor applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete, all as specified and directed. 80 M&L for complete removal of existingold paints and preparing old decorated plastered or unplastered surface of walls and applying two coats of Apex paint(Exterior acrylic emulsion paint)as per designincluding priming coat of exterior primer applied given by Engineer-in-Charge,on wall and roof and similar articles etc.complete all asspecified and directed by Engineer-in-Charge 81 M&L forpreparing new plastered surfaces of ceilingand applying two coats of oil bound distemper over a coat of alkali primer etc all as specified & directed. 82 M&L M&L preparing old plastered surfaces on ceiling andapplying two coats of oil bound distemperetc all as specified& directed. 83 M&L for preparation of new wooden surfaces of any description, over 10cm in width or girthand applyingtwo coats of synthetic enamel paint over a coat ofpink primer, complete, all as specified and directed. 84 M&L for preparation of old paintedwooden surfaces of any description, over 10cm in width or girthand applying one coat of synthetic enamel paintcomplete, all as specified and directed. 85 M&L for preparation of new steel surfaces of any description, over 10cm in width or girthand applyingtwo coats of synthetic enamel paint over a coat ofred oxide primer, complete, all as specified and directed. 86 M&L for preparation of old paintedsteel surfaces of any description, over 10cm in width or girthand applying one coat of synthetic enamel paintcomplete, all as specified and directed. 87 M&L for PCC 25mmthick 1:2:4, type B-0using 12.5 mm graded stone aggregates as in levelling course,complete, all as specified and directed.. 88 S&F in repair PVC SWR pipe 110 mm dia single socketed in any length with rubber ring joints fixed to walls etc all as specified & directed. 89 All as per description of item No 88 above but laid in trenches. 90 S&F in repair PVC SWR pipe 75 mm dia single socketed in any length with rubber ring joints fixed to walls incl vent cowl 75 mm etc all as specified & directed. 91 All as per description of item No 90 above but laid in trenches. 92 S&F in repair 75mm size PVC (SWR) floor trap plain with grating including to jointing with waste pipe with adhessive etc, complete, all as specified & directed. 93 S&F PVC (SWR) 110 mm bore type bends any radius complete, all as specified & directed. 94 All as per item No 93 above but 75mm bore . 95 S&F 100 mm dia stack clampmade out of25x4mmflat iron including nut, bolts etc complete, all as specified & directed. 96 S&F 75 mm dia stack clampmade out of25x4mmflat iron including nut, bolts etc complete, all as specified & directed. 97 S&F in repair PVC SWR pipe 110 mm dia branch pieces (Single T), single (equal or unequal ) ordinary or inverted or with parallel branches with oval access door, complete allas specified & directed 98 S&F in repair PVC SWR pipe 75 mm dia branch pieces (Single T), single (equal or unequal ) ordinary or inverted or with parallel branches with oval access door, complete allas specified & directed 99 S&F sinks made of stainless steel1 mmthickkitchenorlaboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, incl waste coupling and waste pipe etc complete, all as specified & directed. 100 Use and wste of form work to soffits of suspended slab such as roof slab n exc200mm thick (horizontal/sloping/vertical) with fair finished surfacecomplete all as specified & directed. 101 M&L forTMT bars6mm to 8mm dia, cut to length bent to shape required including cranking, bendingand binding with and including MS wire (annealed) notless than 0.9mm dia or securing with clips complete all as specified & directed. 102 Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for, all as directed 103 M&L for reinforced cement concrete (nominal mix) Type B0 1:2:4 (12.5mm graded aggregate) inslabs supported on walls, beams, columnsdeck slabs and in shelves, the like all as specified and directed. 104 S & F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long,complete all as specified & directed. 105 S&F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) 106 M&L 75 mm thickCement concrete type D-2, 1:4:8 using 40mm graded aggregateas in sub bases complete all as specified and directed . 107 M&L for 20mm thick screed bed or bedding layer of cement mortar1:6 for laying floor finishes,complete all as specified & directed. 108 M & L for chequered cement concrete tiles 30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slurry and pigments as in floors complete all as specified and directed. 109 Taking down carefully surface aluminium or copper point wiring onTW Batten/in conduit/ with PVC casing-caping/conduit(light, fan, socket, or power) complete and making good the disturbed surface of wall/celling etc including taking down fitting such asswitches, ceiling roses, pendants, regulators, sockets, light fittings etc and removing material from site, complete, all as specified & directed. 110 M & L for concealed Point wiring complete with 1.5 Sqmm (nominal area)1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable in and including medium grade PVC conduit not less than 20 mm(wall thickness 1.5 mm ) including fitting & accessories, with MS concealed terminal boxes with 3 mm thick laminated baklite (Hylum/Anchor) sheet top cover for mounting switch, socket etc for one light/fan/bell point controled by one switch and(Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm. solid copper conductor with green FRLS PVC insulating earth common earth dolly, complete all as specified. 111 All as per description of serial item No. 110 above but for one socket outlet 6 amp controlled by one switch on the same board with other switches. 112 All as per description of serial item No. 110 above one socket outlet 6 amp controlled by one switch on indepdendent board. 113 M & L forPoint wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia,ISI marked with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for one 16 Amp socket outlet controlled by one switch on independent board, complete. 114 All as per Item No. 110 here-in-beforebut for one light point controlled by two, 2 way switches. 115 S & F switch piano flush button single pole one way 5/6 Amp, complete. 116 S & F switch piano flush button single pole one way 16 Amp complete. 117 S & F of switch piano, flush type, 5 Amps, 230 volts, single pole, two way (ISI marked), complete. 118 S & F socket outlet 2 in 1, 2 & 3 pin, 6 Amp, flush type complete. 119 S & F socket outlet2 in 1, 3 pin16 Amp flush type complete. 120 M & L for lamp holder, PVC/ polycarbonate type with back plate, complete and including taking down unserviceable lamp holder of any description complete all as specified & directed. 121 Supply and fixing of LED lights fitting 1 x 20 W, 220 Volt,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complect as specified & directed. 122 Supply and fixing of LED lights fitting mirror type with high output diffuser 2 feet, 10Watt 220 V AC decorative type with driver holder and LED lamp includingconnecting up with three core flexible copper conductor cable of suitable sizecomplete, all as specified & directed. 123 S & F ceiling rose surface bakelite 65x50mm three terminals, 3 plates complete. 124 S & Felectronic step fan regulator 120 - 280 volts of 100 watt capacity (socket type) including connecting upcomplete. 125 S & F MCB DB SPN 8 waydouble door, IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt, 50 Hz, AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified anddirected . 126 S&FMCBs single pole and neutral 32 Amps, 240 Volts,10 KA rapturing capacity B curve, omplete all as specified & directed. 127 S&F MCBs single pole 6 Amps to 32 Amps, 240 Volts,10 KA rapturing capacity B curve, complete all as specified & directed. 128 S&F in repair of bell AC single pole Ding Dong type 230 Volt all as specified. 129 S&Fbellpush flush type 5 Amps complete all as specified. 130 S & F LED light fitting 1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified & directed. 131 M&L for submain wiring with approved colour code/as per IS (Red, black & green for single phase) concealed conduitcircuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 6.00 Sqmm (FRLS) in PVC conduit (medium grade) including one run of PVC insulated multistrandedcopper conductor nominal cross sectinal area of 6.00 Sqmm (FRLS) of continous earth wire green in colour, complete,all as specified and directed by Engr-In-Charge.Note :- Two runs of 6.00 Sqmm cable & one run of 6.00 Sqmm cable incl PVC conduit shall be paid as one unit length. 132 M& L for painting of ceilingfan complete in situ with synthetic enamel paint by spray painting including preparation of old painted surface and filling cavity with filler one coat after cleaning all dust etc compete, all as specified and directed . 133 S&F exhaust fan, steel body AC single phase. 230V of size 300 mm sweep with blades and frame and louvers all as specified & directed. 134 M&Lfor making opening for exhaust fan by cuttings of holes in PCC or through bricks walls250 to 300 mm dia making good in cement mortar 1:3 or cement concrete 1:2:4 type B2 as required making good the disturbed portion and matching with existing wall finishes, complete,all as specified and directed. 135 S&F exhaust fan, made of sturdy Engineering plastic complete with louvers shutter voltage 230 Volt,50 HZ, 1200 RPMcopper winding of size 250 mm sweep with frame all as specified & directed. 136 S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.all as specified &directed. 137 M&L for Earthing completewith galvanised steel earth plate electrode 60x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers ofgalvanised iron or steel all as shown in electrical plate no. 3 connected to earthing test point all as specified or indicated including testing on complection., earth plate surrounded by packed layers of charcoal dust and common salt 15cm thick, all around includingtop and bottom and watering pipe 20mm bore of GI pipe light grade with funnel and wire mesh, PCC chamber of size 300x300x300mm (top of chamber minimum 15 cm above the normal ground level, PCC 1:3:6 using 20mm graded stone aggregate and RCC cover (1:2:4) type B-I using 20mm graded crushed stone aggregatewith 1 No MS handle madeof 8mm dia including necessary excavation/ earth work in any type of soil/rock and as shown in Electrical plate No. 3 of SSR Part-I (2020) testing on completion complete all as specified & directed. 138 Supply, laying and testing cable XLPE insulated , PVC sheathed, PVC bedded, galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 Volts grade with stranded aluminium condutor of size 16 Sq mm 2 coreincluding taking down the old cable complete all as specified and directed. 139 Excavation in trenchesnot exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, laying of GI pipe, cables etc not exceeding 10 sqm on plan and getting out in Soft/loose of soil complete all as specified & directed. 140 Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick soft/loose soil, all as specified & directed.. 141 Removing excavated soil to a distance not exceeding 50 m and depositingwhere directed at a level not exceeding 1.5 mabove the starting point soft /loose soil, complete, all as directed. 142 M&L for sand cushioning with 8 cm sand beneath the cable and 15 cm above thecableand gently punning the sand above the cable upto10 cm to cushioning the cable complete all as directed by Enginner-in-charge .(Note : The payment will be made for 18cm punned thickness.) 143 M&L for common burnt clay building brick Sub class B designation75 and laying it perpendicular along the length of the cable all as specified and directed. 144 S&F in repair 40 mm bore GI tubing light grade in treches on pole including required fittings, claimps etc for protection of cables complete all as specified & directed. .
