DEPOSIT- Repair and maintenance of stock room in the Department of Periodontics attached to Dental College Thiruvananthapuram.-Work-General Civil Work- 1 Stock room 2 15.7.4:Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar 3 15.23.1:Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm 4 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 5 15.56:Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 6 50.9.1.1:Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood 7 50.9.3.1:Providing and fixing paneled or paneled and glazed shutters for doors, windows and clerestory windows, 30 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding paneling which will be paid for separately, all complete as per direction 0f Engineer in- charge. using Anjili/ Jack wood 8 OD73807/2025-2026: Providing and fixing plywood 4 mm thick, one side decorative veneer conformingto IS: 1328 (type-1), for plain lining / cladding with necessary screws, includingpriming coat on unexposed surface with : Decorative veneer facings of approved manufacture (From DSR 2021 Spec8.28.1) 9 OD108749/2023-2024:Providing and fixingStainless Steel handles of approved quality & make with necessary screws etc all complete.150 mm 10 13.68.1:French spirit polishing:Two or more coats on new works including a coat of wood filler 11 OD70185/2025-2026:Supplying and fixing 200 mm size stainless steel aldrop with stainless steel screws for doors and windows including cost, conveyance and labour charges etc. complete as per the direction of Engineer-In-Charge 12 OD70188/2025-2026: Supplying and fixing 200 mm size stainless steel tower bolts with stainless steel screws for doors and windows including cost, conveyance and labour charges etc. complete 13 OD108751/2023-2024: Providing and fixing Pure Stainless steel floor door stopper(Twin type),ISI marked required color and shape, with necessary screws,etc complete. Additional Details: Details of cost for 10 nos 14 9.70.2:Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:100x58x1.90 mm 15 50.4.1.1:Providing and laying in position cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) up to floor five level excluding the cost of centering, shuttering, finishing for leveling coarse of floor and roof etc. 16 11.41.2:Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm. 17 11.48.2:Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm 18 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 19 10.16.1:Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes 20 OD56949/2025-2026: Providing and fixing 3mm thick Aluminium Composite Panel with minimum thickness of Aluminium layer on both sides 0.25mm fixed with CP Brass/steel screws for paneling in doors and windows/ cupboards/ partitions etc. including all materials, labour charges, hire charges etc. complete as per the direction of Engineer in charge. 21 13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer 22 13.82.2:Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture including applying additional coats wherever required, to achieve even shade and colour.Two coats 23 OD73507/2025-2026:Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work (Form DSR 2021 Spec 13.99) 24 21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) 25 21.1.2.2:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) 26 OD108760/2023-2024:Labour engaging for cleaning the premises, shifting the materials before and after the completion of work.
