Tender For Special Repair To Building No P-33 And T-66 At Mil Station Barabanki Under Ge (East) Lucknow.; 1 Demolition of brick work built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed. 2 M&L for brick work with modular fly ash bricks, straight or curved on plan exc 6m mean radius in CM 1:6 complete all as specified and directed. 3 Taking down of cement plaster in any description on brick or stone wall etc, incl racking out joints hacking for key scrubbing down with water etc complete. 4 M&Lrendering 15mm thick in patches in cement mortar1:6 on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement 5 M&L rendering 15mm thick in patches in cement mortar in 1:4 on fare face of brick work or concrete surfaces even and smoothe without using extra cement & with using integral water proofing compound 6 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm 7 M&L for preparation of new plastered surface of wallsand applying two coats ofoil bound distember including preparity to plastered surface for distemperingcomplete all as specified and directed. 8 M&L for preparation of old plastered surfaces of walls and applying one coat of Oil Bound distemper of approved tint, complete all as specified. 9 Providing and applying white wall care putty of 2 mm thickness over plastered surface to prepare the surface even and smooth. 10 Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm thick above or below ground level complete all as specified and directed. 11 M& L for cement concrete 75mm thick type D - 2 using 40mm graded stone aggregate as in sub base to receive floor finish etc complete all as specified. 12 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premisescomplete all as spd/directed by Engr-in-Charge. 13 M& L for Virified Ceramic tiles double charge/dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm,n.exc 1 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or colouredcement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified and as directed. 14 All as per above item No. 13 buton vertical surfaces including 10mm thick screed plaser in CM 1:4complete all as specified. complete all as specified and as directed. 15 S&F glazed ceramic (non skid) joint free edge cut coloured tiles7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm (400mmx400mmx8mm thick ) set and jointed in neat cement slurry and pointed in colour cement as in floor over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as dierected. 16 S&F ceramic coloured tiles 7 to 8 mm thick 600 x 300mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade. Etc including 10 mm thick rendering in CM 1:4complete all as specified. 17 M&L for broken stone or boulderhard core of gauge not exc 63 mmdeposited spread and levelled in layers not exc.15 cm thick watered and rammed to a true surfaces complete. 18 M&L for cement concrete 1:3:6 type C2 , 75 mm thickas in plinth protectionsmooth without using extra cement incl cutting joints at every 3 m & at corner, Joints to be filled with mastic bituminous. 19 M&L 75mm thick cement concrete type C2, 1:3:6 (40mm graded stone aggregate) as in sub-floors, sub-bases, etc.; all as specified 20 Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings including ridges, hips, valleys and flashings. 21 S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of n colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self taping screws as specified. 22 S & F Pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of n colour having tensile strength of 550 Mpa as in roof covering/clading to wall for ridge and eaves board fixed with self taping screws as specified. 23 Taking down of chowkats or frames not exc 1.5sqm with shutters (with out taking off shutters from the frames). 24 Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters(W/out taking off shutters from the frames). 25 S&F Anodised aluminium powder coated frame work for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified. 26 S&F Anodised aluminium powder coated door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges anodised aluminium snap beading screws etc. complete all as specified. 27 M&L for powder coated (min 50 micron) aluminium three track sliding window with extruded profile of top bottom & side track for fixing 5.5mm thick tinted glass fitted with glazing clips and EPDM rubber in two shutters and fixing SS wire mesh in one shutter and powder coated deco grill including roller and handle, complete all as specified and directed by Engr-in-charge.Note:- (a) including 5.5mm thick tinted glass, SS wiremesh, Deco grill etc in this item.(b) Framed section 3 track size = 92x31.75x1.5mm(c) Shutter section size = 40x18x1.55mm 28 M&L 4.8 mm thick sheet glass, ordinary quality in squares exc. 0.5 Sqm in each pane 29 S&F powder coatingaluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats glazing clips rubber packing, anodised aluminium sanp beading screw , anodised aluminium fittings such as peg stays 150 mm long (01 Nos) hinges type B-21 100 mm long (2 Nos) suitable handles (1 no) complete all as specified. 30 S&F 18/19 mm prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations fixed with screws to timber frame work. 31 Supply only Liquid water proofing compound complete all as spesified and directed. 32 Dismantling of boarding, any description ,fixed in any position with screws etc all as specified and directed. 33 M&L for in repair block board, 18/19mm thick, grade 1 quality, exterior grade, commercial type, fixed with screws to timber frame work as kitchen cabinet and cub board incl 6 mm thick wooden beading on edge and complete fittings (Stainless steel handle 125 mm, piano hinge,)complete,all as specified & directed. 34 S & F 0.9 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturers instructionas complete all as specified and directed. 35 Demolation of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any motar etc all as specified and directed. 36 M&L Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 20mm thick screed in CM 1:4 including cutting, polishing, rubbring & moulding of edges complete all as directed. 37 Rounding to edges of stone slabs one edge, such as in steps, cooking plateform and other similar situation complete all as directed. 38 Dismantling of timber scantling 40 sqcm and over in section in any position as in unframed work complete all as specified and directed. 39 S&F 2nd class hardwood scantling clean swan as in purlins rafters including wooden cleats etc complete all as specified and directed. 40 Dismantling textile covering incl frames (if any) and cover fillets in ceiling (measured flat and not girthed) 41 S&F for 12 mm thick plain Gypsum board false ceiling with GI frame work including all necessary drilling, cutting to fix electrical items as under:-(a) GI Sheet channel 30x25x20mm of 24 Gauge fixed with raql plug and screws 450mm centre to centre along with perimeter of walls (b) GI Sheet channel made to shape 50x40x40mm of 24 gauge placed @ 600mm centre to centre alongwith perimeter of wall except long wall (in one span)(c) GI Sheet intermediate runner of size 45x10x10xmm of 24 gauge fixed @ 1200mm centre to centre to centre leveling frame of one side wall (in one span) (d) GI sheet 25mm wide & 20mm gauge suspenders fixed with steel fasteners to roof ceiling @ 1200 mm centre to centre incl plugging in RCC slab. Fixing of 12 mm thick gypsum boards, filling joints with P.O.P and finshing complete with two coat of plastic emulsion paint over a one coat of primer on ceiling 42 Providing and fixing of E-board Everest or equivalent make 600 x 600 x 4mm thick white prelaminated sett embosed reinforced desigener (lake & HM as approved ceiling board/tiles at all height laid on Armstrong Hot dipped Galvanised imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work will comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers of GI wire 4mm dia to be fixed by approved rawl plugs, level and justers and screws etc. 43 Taking up or down GI tubing 15 mm bore pipe and connections including cleaning for re-fixing or removal to store 44 S&F GI tubing 15 mm bore medium grade galvanise with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm including cutting and chasing complete all as specified. 45 Taking up or down GI tubing20mm bore pipe and connections including cleaning for re-fixing or removal to store 46 S&F GI tubing 20 mm bore medium grade galvanise with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified. 47 S&F in repair vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified. 48 S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mincluding 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sinkincl 40mm dia Waste coupling of PTMT (half or full threaded) .(Minimum weight 32mm-45gms/40mm-60 gms) 49 S & Fin repair stainless steel Kitchen plate rack of overall minimum size 750 mm x 900 mm and 250 mm deep, with partitions for small/large plates etc made out of stainless steel 0.80 mm thick fixed with rawl plug and CP steel screws complete, all as directed. 50 S&F CP grating 125mm dia with waste hole (Minimium weight 40 grams) 51 S&F in repair PVC connection 450 mm long suitable for 15 mm bore GI pipe including CP brass nuts on both sides, complete,all as specified. 52 S&Fin repair long body15mm bore bib tap, cast copper alloy, chromium plated fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule,complete all as specified & directed. 53 S&F in repair 15 mm dia chromium plated fancy type angle valve pipe with capstan head long screwed shank including cp cover plateetc all as specified and directed. 54 S&F in repair 15 mm bore CP brass Central HoleBasin mixture fixed to GI pipe.complete all as sp and directed. 55 S&Fin repairhand shower (Health faucet) with 1 Mtr flexible tube with wall hook bracket etc, complete set of superior quality all as specified and directed. 56 S&F in repair CP shop dish fancy type fixed with SS screw on wall etc all as specified and directed. 57 S&F in repair PVC bath cabinet with 4 mm thick loocking mirror of overall size 560 x 410 mm fixed on wall etc complete all as specified and directed. 58 S&F in repair glass corner self assembly, fancy type,made of 6 to 7mm thick sheet toughened glass of size 250x250mm,fixed with CP brackets,complete,all as specified and directed. 59 Supply & fixin repairsheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long. 60 S&F in repairCP brass tubular towel rail,20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified. 61 S&Fin repair40mm borePVClow density (LDPE) pipe of pressure 6kg/Cm2 fixed to wall or laid in floor, complete,all as specified. 62 S&F in repairs PVC floor trap/nahani trap plan with grating of 100 mm size including jointing to waste pipe with cement joints etc complete as directed 63 Dismantling of PVC drain pipe jointed in lead joints or cement joints and taking out of under floors if required 64 S & F 100 mm dia PVC soil waste and vent pipes sand cast in any length with or without laid in wall with cement joints 65 S & F 75 mm dia PVC soil waste and vent pipes sand cast in any length with or without laid in trenches or in floor with cement joints 66 S & F in repairs 100 mm bore PVC bends of any radius diminshing pieces or tappers (larger bore measured) 67 S & F in repairs 75 mm bore PVC bendswith acces door of any radiusdiminshing pieces or tappers (larger bore measured) 68 S & F in repairs 75 mm bore PVC bends of any radius diminshing pieces or tappers (larger bore measured) 69 S&F 100 mm branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engr-in-charge 70 S&F 75 mm branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engr-in-charge 71 S&F in repair vitreous china floor/wall hung WC with flushing cistern, UF seat cover, hinges, accessories set of size 375 x 650 x 800/370 x 645 x 810 mm fixed to wall/floor with P/S trap complete as per manufactures instructions. 72 S&F 5 mm thick hollowPVC Wall panlling heavy duty including PVC beading at corner and top & bottom of any design, fixed on wall as per manufacture instruction complete all as specified and directed. 73 S & F in repairs vitreous China squatting pan of Orrissa pattern of approved make of size 580 mm X 440 X 260 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe incl lime concrete bedding and connection to antisyphonage pipe etc including making good to floor. 74 S & F in repair vitreous china wash down water closet pan (pedestal pattern/EWC) white (excluding flushing cistern and flush pipe) including connection to drain or out going pipe and flush pipe anti syphonage pipe etc complete and making good to floor complete all as specified and as directed. 75 Complete removal of existing treatment from walls, preparation the surface of wall including cornices plasters etc and applyingtwo coats of cement base paint (any colour as approved) on old treated surface of wall including preparation complete all as specified and directed. 76 M&L for gunniting to RCC works in column beams, slabs, chajja, facia, landing, balconies etc by removing/ dismantling of RCC (loose concrete) and cutting of steel barincluding plaster cleaning of surfaces with wire brushes and applying epoxy, paint anti corrosive coating of minimum 40-50 microns thick with sikatop Armatec 108 or Colusal VL of MC Bauchemie to rusted steel reinforcement after removing cleaning all rust and supply and fixing welded steel wire mesh 75mm x75mm with 4mm dia steel wire as facies/drops and similar works etc and expoxy based or other equivalent suitable bonding against treatment to be carried out on old concrete surface with Sikadur 32 of Sikka.Nito bond EP of fosroc or equivalent (as per manufacturers instruction) to bond old and new concrete mixing @ 2% by weight of cement polycrete and providing gunniting with a minimum pressure of 2 to 2.5 Kg sqcm and applying 25mm thick gunniting in cement mortar (1:2) (one part of cement and two part of ghaghar sand)using ordinary port land cement of 43 grade over wherever required, complete all as specified and directed by Engineer-in-Charge. Note:-(i)After placing the additional reinforcement all concrete surface shall be thoroughly scrubbing with. (ii)Additional reinforced TMT bars where incorporated in work and including 20mm thick cement plaster in 1:4(iii)Work to be carried out as in patches as directed by Engr-in-charge.(iv)Rate for steel scaffolding as directed to be included in quoted rate.(v) All demolished material removed from MOD land completely. 77 S& Fwhite colourtriple layer rotational moulded polyethylene water storage tank (cylindricalvertical with closed top) hoisted and jointed in position all as specified in SSR Part-I (1000 ltr capacity) including dismantling of existing tank and providing all necessary fittings for connecting with pipe line, metal lockable cover. 78 S&F 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & hihdesity plastec ball screwed for iron pipe and fixed.(Minimum weight 20mm - 210 gms) etc complete. 79 S&F 12 mm thick toughened glass as in hinged doors automatic doors and similar work including cutting to shape, drilling holes requiredand pivot at top fance type glass handle of size not less than 300 mm on both sides of shutter to match with colour of glass shutter top and bottom aluminium rail with suitable locking arrangement and all necessary fitting complete all as specified and directed. 80 S&F for frosted film with logo for glass door all as specified and directed 81 S&F 30 mm thick flush shutters, solid coreconstructed with block board core and plywood face panelscommercial type on both side ISI marked 82 S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing and as directed by Engineer-in-Charge 83 Factory made solid panel PVC door shutter pralam30mm thick (style) feather edge consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing. 84 S&F butt hinges of size 100 mm medium weight, stainless steel ISI marked complete all as specified. 85 S&F aluminium handle, 150mm size, 12 mm dia cast type, anodized (ISI marked) complete all as specified. 86 S&F 200 mm long 12 mm dia aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified 87 S&F 300 mm long 16 mm dia aluminium alloy anodised sliding door bolts, with hasp staple (Bolt type) and fixing clips ofsheet cast or extruded sections and fixing bolts and slinding bolts of extruded sections or cast - aluminium alloy and fixed complete, all as specified. 88 Excavation in trenches not exc 1.5 m wide and not exc 1.5m depth and getting out in soft/loose soil completeall asspecified and directed by Engr-in-charge. 89 M&L PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foudation or mass concrete etc complete all as specpfied and directed. 90 Returing, filling in including spreading, leveling, watering and well ramming in layers not exc 25cm complete all as specified and directed by Engr-in-Charge. 91 Removing excavated material n exc 100m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed by Engr-in-Charge. 92 S&F (TMT bars) 10mm dia and over cut to length, bent to shape required,including cranking and bending spirally for hooping for coloumns, hooking ends and binding with and including M.S wire not less than 0.9mm dia all as specified and directed. 93 - Ditto- as per item No 92 but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders complete all as specified and directed. 94 M&L reinforced cement concrete1:2:4 type B1(using 20mm graded stone aggregate) as in columns, pillars, piers, posts all as specified 95 M&L for mild steel framed structural work as in doors or gates of angle or ther section with gusset plates, rairls braces etc complete drilled for fixing of steel sheeting or other covering.Doors etc to be prepared for hanging or slinding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing of Fe-410-0 (Gde E- 250 complete all as directed by Engr-in-Charge. 96 M&L for preparation of new surfaces of steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide complete all as specified. 97 S&F exterior tiles (heavy duty) of superior quaility 400x400x10-12MM thick of approved size/design/shade set and jointed in neat cement slurry & pointed in white or coloured cement to match as in floor over and including 20mm thick screed bed in cm 1:4 complete all as specified and directed. 98 S&F in repair PVC low level flushing cistern of 10 ltrs capacity with dual push buttion inclusive of brackets and PVC bend long type and connectin to flush pipe of any size and pattern with inlet ball valve float and handle complete of approved 99 S&F in repair 15mm bore chromium plated Pillar cock screwed down high pressure, with or without lettered Hot ot Cold with long screwed shanks and flynuts screwed for iron pipe complete all as specified. 100 S&Fin repair toilet paper holder CP fixed complete all as specified and directed . 101 S&F (600mm x 450mm) bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood with aluminium frame 15 x 15 and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified. 102 S&F in repairs long body15mm bore two-way bib tap, cast copper alloy, chromium platedwith capstan head, screwed down, screwed for iron pipe or for brass ferrule,complete all as specified & directed. 103 S&F IInd class hard wood plain, soild chowkhats and frames wrought,framed rebated on the solid rounded or chamfered put together withglue pined at jints all as specified and direcetd at site 104 S&F mild steel work as in hold fast made out of flat iron 25mm x5 mm including necessary welding or fixing with nut and bolts complete all as specified and as directed 105 M&L PCC 1:3:6 type C-1 using 20 mm graded stone aggregate for filling in bed block of hold fast etc complete all as specified and as directed. 106 M&L preparing wood or wood based surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 107 S&F mild steelFramed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 including welding work complete all as specified & as directed. 108 Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc for taking credit including making good the disturbed surfaces to match with the existing complete all as specified and directed. 109 Material and labour for one light / fan point controlled by one, one way switch 06 Amp wiring with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing complete all as specified and directed. 110 All as per serial item No 109 here-in-before but one 3 pin, 06 Amp socket outlet point on independent board controlled by one, one way switch 06 Amp. 111 All as per serial item No 109 here-in-before but one 3 pin, 06 Amp socket outlet point on same board controlled by one, one way switch 06 Amp. 112 All as per Serial Item No 109here-in-before but point wiring with 2.5 Sq mm single core FRLS cables and earth continuity wire of 1.5 Sq mm single core FRLS cable for one 3 pin 16 Amp socket out let point controlled by one, one way switch on independent board complete all as specified and directed. 113 S&F Switch Modular 6A single pole, one way, 1 module complete all as specified and as directed 114 S&F Switch Modular 16A single pole, one way, 1 module complete all as specified and as directed 115 S&F Socket, 6A - 2/3 pin combined 2 module complete all as specified and as directed 116 S&F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and as directed 117 S&F Modular White cover plate with frame,12 module complete all as specified and as directed 118 S&F Modular White cover plate with frame,8 module complete all as specified and as directed 119 S&F Modular White cover plate with frame,3 module complete all as specified and as directed 120 S&F Modular Metal flush box 12 module complete all as specified and as directed 121 S&F Modular Metal flush box 8 module complete all as specified and as directed 122 S&F Modular Metal flush box 3 module complete all as specified and as directed 123 Supply and fix fan step regulator, 120W 2 module complete all as specified and as directed 124 Supply and fix lamp holder, PVC / Polycarbonate type with back plate suitable for batten fitting complete all as specified & directed. 125 Supply and fix in replacement of decorative wall mounting type LED light fitting, 1 x 15 Watt, 230 Volt made up of Polycarbonate including shade, lamp holder, 9/10 Watts LED lamp B22 CDL etc and all accessories pre-wired including connecting up complete all as specified and directed 126 Supply and fix in replacement of integrated LED 2 x 2 round / squarefitting 40 Watt, 6500K with IP 65 protection comprises of high pressure die cast aluminium housing, polycarbonate cover, etc complete all as specified and directed. 127 Supply and fix in replacement of LED security light fitting 25 watt, 5700K with IP 66 protection comprises of a pressure die cast aluminium housing, heat resistance toughened glass, LED lenses, surge protector, electronic driver, etc and all accessories pre-wired including connecting up with PVC insulated copper conductor cable 1.5 Sq mm, 3 core as required for connections and 32 mm bore light grade G. I. tube mounting bracket of 1.5 metre in length, bend to shape at 140 degree in ‘L’ shape and fixed to wall by means of 02 nos. of 40 x 5 mm flat iron clamps, nuts, bolts and washers etc complete all as specified and directed. 128 Supply and fix LED tube light fittings 1200 mm,20 Whigher energy saving decorative ultra slim square profile LED lighting fixture with extruded polycarbonate enviromental friendly, energy efficient complete all as specified and directed 129 Supply and fix LED tube light fittings 600 mm, 10 Whigher energy saving decorative ultra slim square profile LED lighting fixture with extruded polycarbonate enviromental friendly, energy efficient complete all as specified and directed 130 Supply and fix ceiling rose, 6 Amp, 250 volt, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body of 50 x 25 mm sizecomplete all as specified & directed. 131 Taking down carefully ceiling fan of any sweep complete with all accessories, dismantling blades and deposit in safe custody of AGE E/M Yard-II for BER procedure complete all as specified & directed. 132 Material and labour for sub main wiring with 06 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 06 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed. 133 Material and labour for sub main wiring with 04 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 04 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed. 134 Supply and fix in replacement of industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB, SP, AC, 240 volt of 20 Amp, C curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed. 135 Supply and fix in replacement of sheet metal enclosure distribution board, double door, single pole and neutral, AC, 240 volt, 12 way, with 200 Amp rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed. 136 Supply and fix in replacement of sheet metal enclosure distribution board triple pole and neutral (VTPN),double door,AC, 440 volt, 04 way with 200 Amp rated copper bus bar and metal door with IP 54 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed and comprising of the following:-(a) MCCB, 125 Amp, 04 pole, AC, 415 Volt of 16 KA breaking capacity complete - 01 No. (b) MCB, SP, AC, 240 volt of 06 to 32 Amp, C curve, 10 KA breaking capacity - 12 Nos. 137 Supply and fix in replacement of MCB, SP, AC, 240 volt of 06 to 40 Amp capacity C curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed. 138 Supply and fix in replacement of MCB, DP, AC, 240 volt of 32 Amp capacity C curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed. 139 Material and labour for earthing complete with galvanised mild steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level steel earth plate connected with GI wire 04 mm dia by means oflug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15 mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150 mm thick around GI earth plate, GI pipemedium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6 mm dia at the rate of 75 mm centre to centre both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40 mm x 40 mm x 3 mm frame for pit cover including testing on completion complete all as specified and directed. 140 Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) all as specified and directed by Engr-in-Charge 141 S&F exhaust fans, plastic body, ac, single phase, 230/240 v of size 250 mm sweep with louver and making connection with twisted copper flexible wire 23/0.076mm all as specified and directed 142 S&F exhaust fans, heavy duty, ac, single phase, 230/240 v of size 300 mm sweep with louver and making connection with twisted copper flexible wire 23/0.076mm all as specified and directed 143 Supply and fix SRCD D Box 20 Amp with steel enclosure suitable for Geyser & AC protection to human from eletric shock due to direct and Indirect current as well as provide protection from overload and short circuit fault complete with double pole MCB20Ampafter fixing making good surface with fine plastering, finishing and colouring with existing colour matching complete all as specified 144 Cutting walls any type, making holes for fixing of exhaust fan of any size or sweep and making good surface with fine plastering, finishing and colouring with existing colour matching complete all as specified and directed 145 Supply only LED bulb 9/10 Watts suitable for B22 white in colour all as specified and directed. 146 Excavation in trenches in any type of soil not exceeding 1.5 mtr wide and not exceeding 1.5metre in depth for taking out of unserviceable under ground cable complete all as specified and directed 147 Returning, filling in, any type of soil and spreading, in layers not exceeding 25 cm thick complete all as specified and directed 148 Removal of surplus soil (any type of soil obtained from excavation) to a distance not exceeding 50 metre and depositing where directed& complete all as specified and directed 149 Supplying and laying bricks common brunt clay building bricks sub class Binclremoving of old bricks complete all as specified and directed 150 M & L sand cushioning for laying of under ground cableall as specified and directed.( Note:- punned down thickness shall be considerd for mesurement) 151 Supply and fixing of stationery storage type electric BEE 5 star rated Hot Water Geyser of capacity 25 Ltr to operate on 230 volt AC,vertical type, white in colour, working pressure min 0.8 Mpa with glass lined coated tank, magnesium anode, adjustable thermostat, enamel coated incology heating element 2 KW, ABS plastic body,Product warranty-2 Years, Heating element warranty-4 Years, Inner Tank warranty-7 Years, including 4 nos full threaded fastner of size 100 x 10 mm with 2 Nos washer,complete all as specified and directed. 152 Supply, laying, jointing, testing and commissioning in replacement of 35 Sqmm 3.5 Core cable XLPE insulated , armoured heavy duty electric cable with aluminium conductor, 1100 volts grade,laid in trenches,on pole complete all as specified and directedMake
