|
| 1 | Taking down cement plaster of any description on stone /PCC block /brick wall / top of chajja etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris to outside of INS Mandovi Area including filling of open joints in cement mortar 1:6 complete all as specified and directed. |
| 2 | M & L for rendering 15 mm (10+5) thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 in two layers i.e first layer 10 mm thick and 5 mm thick outer layer mixed with WPC as per manufacturer\"s instruction and finished surfaces even and smooth without using extra cement including necessary scaffolding complete all as specified and directed. Note: Quoted rate shall be deemed to be inclusive of cost of waterproofing compound. |
| 3 | M & L for preparation of newly plastered wall surfaces and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 4 | M & L for dubbing coat average 15 mm thick on irregular face of external and internal wall surfaces (when specifically ordered in writing) in CM 1:6 complete all as specified and as directed. |
| 5 | M & L for rendering 10 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 6 | M & L for preparation of newly plastered wall surfaces, priming the surface with alkali resistant priming paint, applying 1mm thick wall care putty and distempering with two coats of distemper oil emulsion, white or tinted complete all as specified and directed. |
| 7 | M & L for rendering 5 mm thick on fair faces of brick work or concrete surfaces on ceilings, soffit of chajja and roof projection in cement mortar 1:3 finished even & smooth without using extra cement complete all as specified and directed. |
| 8 | M & L for preparation of newly plastered ceiling surfaces, priming the surface with alkali resistant priming paint, applying 1mm thick wall care putty and distempering with two coats of distemper oil emulsion, white or tinted complete all as specified and directed. |
| 9 | M & L for washing, rubbing down and stopping of any type of distempered wall surfaces, preparation of the surface, applying 1 mm thick wall care putty wherever required and applying two coats of oil bound distemper of any tint complete all as specified and directed. |
| 10 | M & L for washing, rubbing down and stopping of any type of distempered wall surfaces, preparation of the surface, applying 1 mm thick wall care putty wherever required and applying one coat of oil bound distemper of any tint complete all as specified and directed. |
| 11 | M & L for washing, rubbing down and stopping of any type of painted wall surfaces, preparation of the surface and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 12 | M & L for washing, rubbing down and stopping of any type of painted wall surfaces, preparation of the surface and applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 13 | M & L for complete removal of existing treatment and preparation of old ceiling surfaces and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed. |
| 14 | M & L for preparation of old plastered wall surfaces and applying two coats of white wash complete all as specified and directed. |
| 15 | M & L for preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 16 | M & L for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 17 | M & L for chipping, removing carefully concrete work using low impact hammer, breaking without damaging the structure, cleaning and disposing debris outside the premises complete all as specified and directed.Note: Hard concrete shall not be removed by force. |
| 18 | M & L for cleaning existing reinforcement with wire/ rotary wire brush, making the surfaces free of loose material, rust spalls, dirt etc, applying two coats of alkaline rust converting primer FEOVERT, confirming to ASTM-B-117, on rebars, with time interval of 6 hour between each coat) and applying protective coating of IPNET-RB complete all as specified and directed. |
| 19 | S & F wire netting of stainless steel wire 1.4 mm dia (size of mesh 25 mm) fixed with tinned tacks of stainless steel wire staples, including necessary frame of steel complete all as specified and directed. |
| 20 | M & L for injecting cement slurry grout in the ratio 1:2 (cement : water) and super plasticiser (Supercon-100) at the rate 250 ml/50 kg, mixed by using mechanical mixer stirring continuously; injected by means of pump at a pressure of 0.5 kg/sqcm till grout mix flows out from the nozzles indicating complete filling of grout in the drilled holes for repairs to walls and slabs; as per manufacturer\"s instructions complete all as specified and directed. |
| 21 | M & L for injecting low viscosity MONOPOL (3-5cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories, till nozzles refuse to accept the grout, including mixing of material components (Part a & b) in quantities as per manufacturer\"s instruction by weigh batching, grouting by maintaining the pressure at exit (0.5 to 1.0 kg/cm2) by monitoring pressure guage at exit, grouting the material through prefixed nozzles in the structural elements @ 100ml per nozzle and repeating the process for all the nozzles (beam and columns) complete all as specified and directed. |
| 22 | M & L for drilling and fixing Rohibb Teflon nozzles in RCC structural members, including drilling holes of 12mm dia, 50 to 100mm deep holes in structural members at intervals of 500 center to center in staggered manner and carrying out the work as under complete all as specified and directed. (i) Cleaning of holes : Holes shall be cleaned by air blower prior to fixing nozzles.(ii) Fixing of nozzles : 12mm dia Rohibb Teflon nozzles shall be inserted in cleaned holes. External end of nozzles to be machine cut to receive outlet of grouting gun. Nozzles shall be fixed inside the holes by applying thixotropic epoxy putty to ensure complete sealing. The system shall be cured for min 12 hrs. (iii) Cutting of nozzles : Nozzles shall be cut by chisel after completion of grouting without damaging structural elements. |
| 23 | M & L for providing and applying jacketing around columns with micro concrete (Molith-MC) M40 including lifts, shuttering, drilling holes and fixing shear anchor complete all as specified and directed. Note: Reinforcement shall be measured and paid separately. (Quoted rates shall be deemed to be inclusive of jacketing, formwork and micro concrete) |
| 24 | M & L for providing TMT bars mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips for stiffner of chainlink fencing complete all as specified and directed. |
| 25 | Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 26 | M & L for providing cement concrete 1:2:4 type B0, using 12.5mm graded crushed stone aggregate in roof kerbs or mud stops, rounded or chamfered on edges on concrete surfaces over top of RCC chajjas using waterproofing compound as per manufacturer\"s instruction fcomplete all as specified and directed.Note: Quoted rate shall be deemed to be inclusive of cost of waterproofing compound. |
| 27 | Dismantling single layer Mangalore pattern or similar tiles in roofing complete all as specified and directed. |
| 28 | M & L for laying roof tiles, Mangalore pattern, interlocking at side joints, laid dry complete all as specified and directed. |
| 29 | M & L for providing ridge or hip tiles to suit Mangalore pattern of roofing Tiles, bedded and jointed in cement mortar 1:6 complete all as specified and directed. |
| 30 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed. |
| 31 | S & F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 32 | S & F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.Note: Width of ridge sheet shall be 60cm on both sides |
| 33 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 34 | S & F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc in Fe-290 Gde E-165 complete all as specified and directed. |
| 35 | M & L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 36 | Demolition of precast concrete articles and precast concrete block walling built in cement mortar or cement lime mortar complete all as specified and directed. |
| 37 | M & L for precast cement concrete block masonry with solid blocks of PCC 1:3:6 type C1 using 20 mm graded trap aggregate, exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed. |
| 38 | M & L for preparation of new wall surfaces and applying two coats of white wash complete all as specified and directed. |
| 39 | Disconnecting existing tanks of capacity exc. 250 ltr and n.exc. 500 ltr, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required, reconnecting and re-fixing in position complete all as specified and directed. |
| 40 | Disconnecting existing tanks of capacity exc. 500 ltr and n.exc. 1000 ltr, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required, reconnecting and re-fixing in position complete all as specified and directed. |
| 41 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 42 | M & L for providing 15mm thick screed bed or bedding layer of cement mortar 1:6for laying floor finishes complete all as specified and directed. |
| 43 | M & L for rendering 10 mm thick onfair faces of brick work or concrete vertical surfaces in cement mortar 1:4 complete all as specified and directed. |
| 44 | M & L for providing granite tile work using granite (of any type) tiles, 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed withwhite cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed. |
| 45 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and directed. |
| 46 | M & L for providing glazed ceramic coloured tiles in vertical surface, 350 x 250 x 7 mm/ 450 x 350 x 7 mmthick, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 47 | M & L for providing non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 48 | M & L for providing non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 49 | M & L for providing non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 50 | M & L for providing chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments complete all as specified and directed. |
| 51 | Taking down steel tubing and connections of 15 mm dia bore complete all as specified and directed. |
| 52 | Taking down steel tubing and connections of 20 mm dia bore complete all as specified and directed. |
| 53 | Dismantling water tanks of capacity exc 250 ltr & n exc 500 ltr and removing to store complete all as specified and directed. |
| 54 | Dismantling water tanks of capacity exc 500 ltr & n exc 1000 ltr and removing to store complete all as specified and directed. |
| 55 | Supplying and laying of CPVC pipes of 20 mm outer dia, SDR 11 & plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and directed. |
| 56 | Supplying and laying of CPVC pipes of 25 mm outer dia, SDR 11 & plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and directed. |
| 57 | S & F in repairs bib taps (long body), cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15mm dia bore complete all as specified and directed. |
| 58 | S & F in repairs stop valves, copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends, for iron pipes or for unions of 15 mm dia bore complete all as specified and directed. |
| 59 | S & F in repairs pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with fly nuts screwed for iron pipes of 15 mm dia bore complete all as specified and directed. |
| 60 | S & F in repairs brass chromium plated shower rose, 125 mm size with shower arm of 15 mm size, 195mm long with 45 degree bend and flange complete all as specified and directed. |
| 61 | S & F 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 62 | S & F PTMT bathroom mirror cabinet of size 600mm x 450mm x 200mm with all necessary arrangements for fixing to wall complete all as specified and directed.Make: Shakthi Cat Pt No SB-155 or Water Tec or equivalent |
| 63 | S & F in repairs plastic water closet seat, white, closed pattern with flat bottom, cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 64 | S & F in repairs toilet paper holder, flat recessed type, stainless steel, including all necessary fittings complete all as specified and directed. |
| 65 | S & F in repairs brass, tubular towel rail, chromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and directed. |
| 66 | S & F in repairs grating doom 100mm dia of PTMT (Minimum weight 40 gms) including jointing with solvent cement complete all as specified and directed. |
| 67 | S & F in repairs 32 mm dia waste pipe, 800 mm long complete all as specified and directed. |
| 68 | S & F in repairs 2 in 1 health faucet with hook, chromium plated, with 1.5 m tube complete all as specified and directed. |
| 69 | S & F in repairs vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed. |
| 70 | S & F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm, white, with integral foot rests, excluding flushing cistern and flush pipe, complete all as specified and directed. |
| 71 | S & F in repairs vitreous China bowl urinal flat back, full stall type, white, with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; flush pipe, grating and union for discharge pipe complete all as specified and directed. |
| 72 | S & F in repairs PVC valveless, syphonic action type, flushing cistern of 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified and directed. |
| 73 | S & F PVC connections of 15 mm size and 450 mm long with PTMT nuts complete all as specified and directed. |
| 74 | S & F PVC connections of 15 mm size and 600 mm long with PTMT nuts complete all as specified and directed. |
| 75 | S & F in repiairs wash basins, Vitreous China, flat back or angle back type, 550mm x 400mm size, including brackets and cutting for and pinning in ends of brackets or erecting stand and fixing of polyethylene of low or high density or PVC. 32 mm dia waste pipe complete all as specified and directed. |
| 76 | S & F sinks with drainage board made of stainless steel 1 mm thick, kitchen with plugs, washers and wastes; includding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, of overall size 915mm x 460 mm and of bowl size 410mm x 330mm x160mm complete all as specified and directed. |
| 77 | S & F 500 litre capacity rotational moulded polyethylene water storage tanks (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and directed. |
| 78 | S & F 1000 litre capacity rotational moulded polyethylene water storage tanks (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and directed. |
| 79 | S & F in repairs ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 25 mm dia bore complete all as specified and directed. (minimum weight 25 mm - 455 gm) |
| 80 | S & F in repairs ball valves to CPVC pipe of 25 mm dia bore complete all as specified and directed. |
| 81 | S & F in repairs tank adaptor to CPVC pipe of 25 mm dia bore complete all as specified and directed. |
| 82 | M & L for PVC (SWR) floor trap of 75 mm dia outlet, plain with grating including jointing with solvent cement, fixed in repairs, complete all as specified and directed. |
| 83 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed. |
| 84 | S & F 160 mm dia bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, solvent cement jointed fixed to walls complete all as specified and directed. |
| 85 | S & F PVC (SWR) bends of 160 mm dia bore, any radius, with acess door complete all as specified and directed. |
| 86 | S & F 110 mm dia bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, solvent cement jointed fixed to walls complete all as specified and directed. |
| 87 | S & F PVC (SWR) bends of 110 mm dia bore, any radius, with acess door complete all as specified and directed. |
| 88 | Dismantling/ taking down existing hessain base felt or clay tiles or any other existing water proofing treatment from roof/ chajja including cement plaster, cleaning the surface and removing the dismantled debris to a distance exceeding 1.50 km but not exc 5 km to outside the MD land and laying water proofing membrane treatment using 4mm thick APP modified membrane consisting five layer membranes, weighing not less than 4.00kg/sqm laid over a coat of cold bituminous primer @ 0.40 kg/sqm by torching the membrane and sealing the overlap by 100mm length side and 150mm width side all as per manufacturer\"s instructions including joints and changes in direction be curved with 10mm thick cement mortar 1:3 mixed with SBR latex @ 2.00ml/bag of cement, curved well before laying of membrane, including applying two coats of solar reflective bituminous aluminium paint @ 0.10 litre/sqm complete all as specified and directed.Note: (i) Irrespective of lap, the net covered area will only be measured for payment. (ii) Quoted rate shall be deemed to be inclusive of bituminous primer, APP membrane, solar reflective bituminous aluminium paint and SBR latex. |
| 89 | M & L for providing 25 mm thick cement concrete 1:2:4 type B0 (using 12.5mm graded stone aggregate) on concrete surface over top of RCC roof using waterproofing compound as per manufacturer\"s instruction finished even and fair using extra cement complete all as specified and directed.Note: Quoted rate shall be deemed to be inclusive of cost of waterproofing compound. |
| 90 | Taking down shutters of any descrption not exceeding 1.0 sqm eachfrom chowkhats, complete all as specified and directed. |
| 91 | Taking down shutters of any description, exceeding 1.0 sqm but not exceeding 2 sqm each, from chowkhats, complete all as specified and directed. |
| 92 | Taking down chowkats or frames not exceeding 1.5 sqm each, with shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 93 | Taking down chowkats or frames exceeding 1.5 sqm but not exceeding 4.0 sqm each, with shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 94 | Taking down chowkats or frames not exceeding 1.5 sqm each complete all as specified and directed. |
| 95 | Taking down shutters of any description n exc 1 sqm each and refixing in same opening complete all as specified and directed. |
| 96 | Taking down chowkats or frames exceeding 1.5 sqm but not exceeding 4.0 sqm each complete all as specified and directed. |
| 97 | Taking down shutters of any description exc 1 sqm and n exc 2 sqm each and refixing in same opening complete all as specified and directed. |
| 98 | S & F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. |
| 99 | S & F 2nd class hard wood, 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); and fitted to chowkats complete all as specified and directed. |
| 100 | S & F factory made plain framed, panelled shutter (two panel) of 40 mm thick, with 2nd class hardwood rail and style, with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, the size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed. |
| 101 | M & L for forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, in CM 1:6 complete all as specified and directed. |
| 102 | S & F mild steel ordinary rat tail door springs (capsule type), 300 mm long, including roller and roller plate complete all as specified and directed. |
| 103 | S & F in repairs mild steel ordinary rat tail door springs (capsule type), 300 mm long, including roller and roller plate complete all as specified and directed. |
| 104 | S & F extruded aluminium alloy handles, 150 mm long, fabricated type, anodised complete all as specified and directed. |
| 105 | S & F in repairs extruded aluminium alloy handles, 150 mm long, fabricated type, anodised complete all as specified and directed. |
| 106 | S & F extruded aluminium alloy handles, 100 mm long, fabricated type, anodised complete all as specified and directed. |
| 107 | S & F in repairs extruded aluminium alloy handles, 100 mm long, fabricated type, anodised complete all as specified and directed. |
| 108 | S & F aluminium anodised, barrel tower bolts of extruded section and 150 mm length complete all as specified and directed. |
| 109 | S & F in repairs aluminium anodised, barrel tower bolts of extruded section and 150 mm length complete all as specified and directed. |
| 110 | S & F aluminium anodised, barrel tower bolts of extruded section and 100 mm length complete all as specified and directed. |
| 111 | S & F in repairs aluminium anodised, barrel tower bolts of extruded section and 100 mm length complete all as specified and directed. |
| 112 | S & F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 113 | S & F in repairs 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 114 | S & F in repairs aluminium plate type II, gate and shutter, hooks and eyes of size 150 mm complete all as specified and directed. |
| 115 | S & F in repairs 125 mm long hasp and staple, safety type, aluminium anodised hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 116 | S & F 100 mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and directed. |
| 117 | S & F 75 mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and directed. |
| 118 | S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty / beedingin squares not exceeding 0.5 sqm in each pane complete all as specified and directed. |
| 119 | Hacking out old broken glass (any thickness, size, quality or description) from wooden/ steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. |
| 120 | S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty / beedingin squares exceeding 0.5 sqm in each pane complete all as specified and directed. |
| 121 | S & F 4 mm thick figured glass, pin head type and glazing with oil putty/ beeding in squares exc 0.5 sqm in each pane complete all as specified and directed. |
| 122 | S & F aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with aluminium wire staples complete all as specified and directed. |
| 123 | S & F in repairs aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with aluminium wire staples complete all as specified and directed. |
| 124 | S & F mild steel clamps; hold fasts; wall ties and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 125 | M & L for providing PCC 1:3:6 type C1 using 20mm garded stone aggregate, for fixing hold fast complete all as specified and directed. |
| 126 | M & L for preparing new wooden surfaces of any description exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 127 | S & F in repairs door closer, hydraulically regulated, designation No. 3, universal type, aluminium (die cast) body, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed. |
| 128 | S & F in repairs 40 mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed. |
| 129 | S & F in repairs snake guards on bottom sides of doors (door sealing strip) of aluminium plate and nylon bristles for weather stripping, air and sound blocking complete all as specified and directed. |
| 130 | S& F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat ofFrame size 65x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with and including MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge,as per specification & drawing Note: 1. For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. 2. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 131 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm thickcomprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: Stainless steel butt hinges and necessary S S screws shall be paid separately under relevant item of this schedule. |
| 132 | S & F in repairs plain aluminium sheeting, 0.56 mm thick, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete all as specified and directed. |
| 133 | S & F in repairs floor door stopper of aluminium alloy body and tongue, anodised with hard draw steel spring, 140mm overall length of cover plate complete all as specified and directed. |
| 134 | M & L for providing 18/19mm thick prelaminated particle board, exterior grade, prelaminatedone side with decorative choice lamination and other side balancing white lamination, fixed in repiars with screws to timber frame work in cup board shelves complete all as specified and directed. |
| 135 | S & F continuous (piano) hinges, mild steel, bright finish or electrogalvanised, of 30mm wide flaps (when open) complete all as specified and directed. |
| 136 | S & F in repairs continuous (piano) hinges, mild steel, bright finish or electrogalvanised, of 30mm wide flaps (when open) complete all as specified and directed. |
| 137 | S & F hasp and staple, 100mm long, safety type, aluminium anodised including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 138 | Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required, depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall exc. half brick but not exc.one brick complete all as specified and directed. |
| 139 | S & F in repairs mild steel mortice lock, 4 lever, vertical type, size 65 mm complete all as specified and directed. |
| 140 | S & F in repairs 100 mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and directed. |
| 141 | S & F in repairs 75 mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and directed. |
| 142 | M & L for greasing and easing only to existing rolling shutters, area of shutter exc 5.0 Sqm and not n exc 10 Sqm each complete all as specified and directed. |
| 143 | S & F in repairs curtain rails of anodised aluminium alloy with fixing brackets, stops, rollers etc complete all as specified and directed. |
| 144 | S & F aluminum powder coated window/ ventilator shutter including frame, any type (sliding or open-able) and other similar work etc, fabricated, with approved standard sections, including necessary arrangement to receive 4mm thick sheet glass or wire mesh with aluminium channel beading, stainless steel screws, rollers, maruti lock including the cost of rubber gasket / rubber beading, rollers, maruti lock etc, fixing frames complete all as specified and directed.Note: Weight of rubber gasket / beading rollers, maruti lock will not be measured with weight of aluminium shutter. Note: Sheet glass & wire mesh shall be measured and paid separately. |
| 145 | S & F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement complete all as specified and directed. |
| 146 | M & L for cleaning of RCC /AC/PVC water tank (staged over the bldg), capacity not exc. 500 ltrs, by removing float valve carefully, draining out water, scrapping down by wire brush for removing fungus, mud scales etc., washing down with fresh water, refixing float valve in same position, spreading bleaching powder inside water tank and applying one coat white/ colour wash on external surface complete all as specified and directed. |
| 147 | M & L for cleaning of RCC /AC/PVC water tank (staged over the bldg), capacity exc. 500 ltrs but not exc. 1000 ltr, by removing float valve carefully, draining out water, scrapping down by wire brush for removing fungus, mud scales etc., washing down with fresh water, refixing float valve in same position, spreading bleaching powder inside water tank and applying one coat white/ colour wash on external surface complete all as specified and directed. |
| 148 | M & L for cleaning of RCC /AC/PVC water tank (staged over the bldg), capacity exc. 1000 ltrs and not exc 2000 ltr, by removing float valve carefully, draining out water, scrapping down by wire brush for removing fungus, mud scales etc., washing down with fresh water, refixing float valve in same position, spreading bleaching powder inside water tank and applying one coat white/ colour wash on external surface complete all as specified and directed. |
| 149 | Note: An amount of Rs 64115.00 on account of Credit Schedule for Schedule A Part II shall be deducted from the total amount of BOQ to arrive at Contract Sum. |
