Tender For Making Rooms And Miscellaneous Works At Vivekananda Hostel Of Iiitdm Jabalpur.; 1 MASONRY WORK 2 Providing and fixing 25 mm thick limestone(Kadappa stone) slab of required size and shade for making racks embedded in brickwork including cutting,making key joint and filling the joints with cement mortar of 1:4 ratio. 3 Providing and fixing window roller for the sliding aluminium window shutter with all necessary screws and fittings. 4 Providing and fixing window lock for the sliding aluminium window shutter with all necessary screws and fittings. 5 Providing and fixing health faucets into the washroom area with holder,necessary screwsetc. 6 P/F CP Uninal Push valve (concealed) of standard design and of approved make conforming to IS standard. 7 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 9 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 10 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 11 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) 12 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 13 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 14 Thermo-Mechanically Treated bars of grade Fe-500D or more. 15 Centering and shuttering including strutting, propping etc. and removal of form for 16 Lintels, beams, plinth beams, girders, bressumers and cantilevers 17 ProvidingandlayingAutoclavedAeratedconcreteblocks (AAC)masonry 150mm/230mm/300mmthick AACwith Grade-1blocks of density 551-650 kg/cum conforming to IS:2185 (Part 3)in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block layingpolymermodifiedadhesivemortarallcompleteasperdirectionof Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). 18 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 19 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. 20 Granite stone slab of colour black, Cherry/Ruby red 21 Area of slab upto 0.50 sqm 22 WOOD AND P. V. C. WORK 23 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : 24 Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading 25 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 26 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 27 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws 28 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 29 30 mm thick shutters 30 with ISI marked M.S. pressed butt hinges bright finished of required size 31 Kiln seasoned and chemically treated hollock wood 32 Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete : (copper oxidized as per IS: 1378) 33 150 mm 34 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. 35 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 36 250x16 mm 37 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 38 200x10 mm 39 100x10 mm 40 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 41 100 mm 42 75mm 43 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 44 Twin rubber stopper 45 Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. 46 Double strip (horizontal type) 47 Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge. 48 Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC C channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the C Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturers specification & drawing. 49 30 mm thick pre laminated PVC door shutters 50 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 51 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 52 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 53 25 mm thick 54 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 55 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 56 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 57 110 mm diameter 58 FINISHING 59 12 mm cement plaster of mix : 60 1:6 (1 cement: 6 coarse sand) 61 Finishing walls with Acrylic Smooth exterior paint of required shade: 62 New work (Two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.9Lt/10 sqm) 63 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 64 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 65 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 66 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. 67 Two coats 68 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 69 In cement mortar 70 Dismantling dressed stone work ashlar face stone work, marble work or precast concrete work manually/ by mechanical means including stacking of serviceable and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge: 71 In cement mortar 72 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever) conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls andfloors wherever required: 73 White Vitreous china Orissa pattern W.C. pan of size580x440 mm with integral type foot rests 74 Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls andfloors wherever required: 75 W.C. pan with ISI marked white solid plastic seat and lid 76 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brasspillar taps, 32 mm C.P. brass waste of standard pattern, includingpainting of fittings and brackets, cutting and making good the wallswherever require: 77 White Vitreous China Wash basin size 550x400 mmwith a pair of 15 mm C.P. brass pillar taps 78 Providing and fixing white vitreous china flat back or wall corner typelipped front urinal basin of 430x260x350 mm or 340x410x265 mmsizes respectively. 79 Providing and fixing P.V.C. waste pipe for sink or wash basin includingP.V.C. waste fittings complete. 80 Flexible pipe 81 32 mm dia 82 Providing and fixing mirror of superior glass (of approved quality) andof required shape and size with plastic moulded frame of approvedmake and shade with 6 mm thick hard board backing: 83 Rectangular shape 453x357 mm 84 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls 85 20 mm nominal dia Pipes 86 25 mm nominal dia Pipes 87 32 mm nominal dia Pipes 88 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 89 50 mm nominal dia Pipes 90 Providing and fixing uplasticised PVC connection pipe with brass unions : 91 45 cm length 92 15 mm nominal bore 93 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 94 100 mm diameter 95 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 96 15 mm nominal bore 97 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 98 15 mm nominal bore 99 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 100 15 mm nominal bore 101 Providing and fixing PTMT grating of approved quality and colour. 102 Circular type 103 100 mm nominal dia 104 ALUMINIUM WORK 105 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately): 106 For fixed portion 107 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) 108 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 109 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) 110 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 111 With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) 112 Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit with modular switch, modular plate suitable GI Box & Earthing the point with 1.5 sq.mm FRLS PVC insulated copper condutor single core cable etc. as reqd. 113 Group A 114 Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduitas reqd. 115 4 x 10 sq. mm. + 2 x 6 sq. mm. earth wire 116 Supplying and drawing of following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/PVC conduit etc. as required. 117 3 x 1.5 sq. mm. 118 6 x 1.5 sq. mm. 119 9 x 1.5 sq. mm. 120 Supplying and fixing of following sizes of medium class PVC conduit alongwith accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 121 (a) 25mm 122 (b) 32mm. 123 Supplying & fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. 124 3 pin 5/6 amp switch 125 3 pin 5/6 amp socket outlet 126 RJ45 computersocket outlet 127 Supplying and fixing 2 module stepped type electronic fan regulator on the existing modular plate switch box including connection but excluding modular plate etc as required. 128 Supplying & fixing following size/ modules , GI box along with modular base and cover plate for modular switches in recess etc as required. 129 8 module (125mm x 125mm) 130 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 131 1 run of cable 132 Providing and fixing folowing capacity TP&N disconnector fuse swith unit inside the existing panel board with ISI mark HRC fuse including drilling hole in cubical panel, making connections etc. as required 133 32A TP&N 134 Supply and fixing following way horizontal ways type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/recess, complete with tinned copper bus bar, neutral bas bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (but without MCB/RCCB/Isolator) 135 6 way (4+18), Double door 136 Supply and fixing 5A to 32A rating,240/415 V, 10KA C curve minuature circuit breaker suitable for inductive load of following poles in the existing MCB BD, complete with connections, testing and commissioning etc. as required 137 Single pole 138 Supplying, Installation, testing and commissioning of following sweep Ceiling fan including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq mm FRLS PVC insulator, Copper conductor, single core cable etc as required. (Cropmton, Havells, Bajaj) 139 a) 1200 mm sweep 140 Supplying, Installation, testing and commissioning of following prewired LED light fitting of all type complete with all accessories on ceiling connection with 3 x 1.5 sq mm FR LS insulated copper conductor wire etc as reqd. 141 a) Wall mountedlight fixture suitable for 1x20 watt LED Tube light fixture complete as reqd. (Make:Crompton,Phillips, Havels)
