Tender For Repair To Wpt In Sunken Slab , Rcc Roof, Flooring And Misc B&R Work At Aicts , Ngm, Ogm, Fafa, Qtrs And Connectedarea Under Age B/R -I (S) Of Ge South Pune.; 1 Demolition of cement concrete of any description and in any position not otherwise specifically provided for but including sunken portion and floor tiles and roof concrete , unreinforced etc all as specified and as directed. 2 Material and labour Water proofing treatmenttosunken slab, walls,etc, shall be carried out as specified below and as directed by Engineer-in-Charge.(a) Clean the sunken portion of toilet/Baths/WCs/Kitchen thoroughly remove laitance, dirt, dust etc.(b) Form angle fillet of size 40 mm x 40 mm along the junction of wall and floor using polymer modified mortar (“ Dr fixit” Pidicrete URP” or eqvt).(c) Sanitary pipes entering through walls and floor shall be sealed with “Dr Fixit Bath seal Tape” and the gaps to be grouted with non-shrink cementitous grout “Dr Fixit Bath seal Grout” or eqvt. Nahani traps etc to be fitted securely and the gaps around it to be grounted in the same manner.(d) Apply one coat of a Bitumen-modified polymer coating “Dr Fixit Bath seal Plus” or eqvt on all angle fillets by brush and cover it with 100mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely. 3 (e) In the remaining area, in dry substrate condition brush apply first coat of the same coating and further apply second coat when first is dry. Extend the coating upto150mm above the FFL.(f) After 2 to 3 days, sunken portion must be overlaid with a 50 mm thick concrete screed 1:3:6 type B0 mixed with integral WPC (Liquid) laid to slope 1:60 towards outer face of wall. Provide 40 mm OD UPVC pipe at the lowest point with 300 mm projection beyond the outer face of the wall. After satiscfactory ponding test Then fill up the sunken portion with lean concrete 1:5:10 type E2. (Note : Lean concrete 1:5:10 Type E2 shall be measured and paid separetly. (g) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready to make tile grouts of approved makes such as Dr Fixit, FOSROC SIKA, MC BUCHEMIE, ROFF, etc. 4 M/L for PCC 1:5:10 type E2 (using 40 mm graded brick aggregate)lean concrete for filling sunken floor etc. 5 M&L forcleaning the roof portion Thoroughly remove laitance diert dust ect .and form angle filletsof size 40 mm x 40 mm along the juction of wall and floor using polymer molymer modified mortar (Dr Fixit PidicreteURP or Eqvt). incl 40 mm thick PCC 1:2:4 type B0 (Using 12.5mm graded aggregate) finishing cement concrete surface even and smooth with extra cement with water proofing compound as on roof. mixingwater proofing. 6 M&L for water proofing treatment by applying primer @ 0.20 kg per sqm, providing and laying 3 mm thick APP modified water proofing membrane weighing not less than 3.00 kg per sqm reinforced with non woven polyester matt weighing not less than 100 gm per sqm having softening point not less than 140 degree centigrade, longitudinal tensile strength not less than 300 N per sqm tearning strength of 100 N by torch on application including minimum over lapping 10 cm on either side and 15cm on ends and applying evenly a tack coat of hot blown bitumen grade 85/25 bottom of AAPmembrane @ 1.20 Kg / sqm including two coat of solar reflective paintcompleteincludingdismantling of old unserviceable water proofing treatment / membrane and removal of debreies / dismantled materials complete all as specified and directed.Note : (a)The water proofing treatment shall be carried out by company authorized applicator only 7 M&L for rendering 15 mm thick onfair faces of brick work/ concrete surfacein cement mortar 1:4with water proofing compound finished even and smooth withusing extra cementat Chhajja and above wallafter M&L fordubbing out 15 mm thickin cment mortar 1:4 on irrugular surface.( WPC shall measured and paid sepretally)(Note: - Quoted rates shall be deemed to be inclusive of necessary scaffolding / security measures as the work to be carried out for elvated up to 12 mtr height Building .) 8 Removing of existing water tank of capacity 500,1000 or 2000 Ltr setting aside (or lowering if required) for repair, cleaning etc and reconnecting & refixing in position after carrying out necessary roof treatment including necessary fittings and GI Pipes if required complete all as specified and directed.(NOTE : Necessary by pass arrangements for water supply is to be done by the contractor till completion of roof work.) 9 Dismantiling structural steel work including doors,gatesbut excluding framed trusses etc complete all as specified and directed. 10 S & Froof sheeting prepainted galvalume aluminium zinc coating 150 gms GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed including dismantling of old AC sheet complete all as specified and directed. 11 S & Froof sheeting prepainted galvalume aluminium zinc coating GI based plainsheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified incl dismantling of old sheet complete all as specified and directed. 12 S&F 1.25 mm thick Plain, black, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashingsincl welding and solding jointand incl dismantling oldgutter (length and girth as fixed) complete all as specified and directed. 13 S&F 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc. fixing with L-type or J- type or crank hook bolt etc and incl dismantling of old sheet complete all as specified and directed. 14 Dismantling and refixing old asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc. fixing with L-type or J- type or crank hook bolt etccomplete all as specified and directed. 15 M&L for MS structural steel work, framed as in trusses, purlins, rafter, post etc. conforming to grade E-250 (Fe-410W, quality A) including shaped washers including necessary cutting required length, notching drilling, riveting and or welding or connecting with nut bolts with angle cleats, fish plat, gusset plate and also erecting in true position complete as directed. 16 M&LforMangalore pattern roof tiles, interlocking at side joints, laid dry including dismantling of existingcomplete all as specified and directed. 17 M&Lfordismantling and refixing oldMangalore pattern roof tiles, interlocking at side joints, laid dry complete all as specified and directed. 18 M&L for Ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in lime mortar 1:3 or cement mortar 1:6 including dismantling existing complete all as specified and directed. 19 M&L forsecond class hard wood Clean sawn battens of sectionalareaexc 15 & n. exc 25 Sq.cm and at 25 cm centres including dismantling existing in any positioncomplete all as specified and directed. 20 M&L fordisamtling and refixing second class hard wood Clean sawn battens of sectionalareaexc 15 & n. exc 25 Sq.cm and at 25 cm centres complete all as specified and directed. 21 M&L for clean swanSecond class hard-wood in scantlings including dismantling of existing in any positioncomplete all as specified . 22 S&F for20 mm thick boarding plane both side with butt joint for roof including dismantling existingall as specified 23 S&F false ceiling with 9 to 9.5mm thick glass fibre reinforced Gypsum ceiling tiles of size 595 X 595 mm ,prima fine fissured micro look white coloured laid over including grid work 600 x 600mm using GI powder coated “T:” section grid as Main T 38 X25 mm , cross T 25x25mm and wall angle 25x25mm grid and 6 mm dia GI suspension wire etc complete all as specified anddirectedincluding taking exsitingfalse ceiling/ liningetc Make-Saint-Gobain, Armstrong,Diamond or Equivalent. 24 M & L for cleaning of roof area not exceeding 300 Sqcm each and chajjas of bldgs front, rear and side complete. clearing mouth of rain water pipes and spouts in chajjas etc complete including removals of roots of Tree , vegetative growth, algae, small plants and applying hydrochloric acid on the left over roof portion etc and making good the existing surface with cement mortar plaster in CM 1:3 mixed with WPC @ 3% of weight of cement, minium area of cement plaster per block - 05 Sqm, complete all as directed by Engr-in-Charge.(Note: - Quoted rates shall be deemed to be inclsive of necessary scaffolding / security measures as the work to be carried out for elvated up to 15 mtr height Building .) 25 Supply and fix in replacement rotational moulded polyethylene water storage tanks(vertical cylindricalwith closed top) double layered ISI marked with existing inlet, outlets & provision ofwashouts, (vent pipe all as directed offollowing capacityincluding all new tank nipples of suitable size.Including dismantling old water tanks all as specified and directed . 26 (a) 500 ltr. 27 (b )1000 ltr. 28 (c) 2000 ltr. 29 M/L for PCC 1:2:4 type B0 (using 12.5 mm graded brick aggregate) as in coving rounded, chamfered,sub base above lean Concrete , tank staggingand other etc on sunken floor complete all as specified and directed. 30 M&L for PCC 1:2:4 type B-0, 25 mm average thickness, levelling course as in padding concrete complete all as specified and directed. 31 M&L for 300x300x 6 to 7mm thick, non skid, ceramic, coloured tiles, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete over and including 15mm thick screed bed in CM 1:6 completeincluding demolition of existing tiles of any description all as specified & directed by Engr-in-Charge. 32 M&L glazed coloured digital printed ceramic tiles of size 600 mm x 300mm x 7mm thick in vertical surfaceses etc set qnd jointed in neat cement slurry and pointed in colouredcement to match with colour tiles including 15 mm thickbacking coat in CM (1:4) and filleting at top etc complete and including taking down of existing tles of any description etc complete all as specified and directed. 33 M&L formatt finished, coloured ceramic tiles 7 to 8 mm thick 600 x 600mm size of approved colour, set, jointed in cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 20 mm thickscreed bed in CM 1:6 etc complete as in flooringincluding demolition of existing tiles of any description etc all as specified and directed. 34 M&L for 16 to 18mm thickGranite slab(of any type/colour) work (table rubbed and polished) in steps,pillars;window cills/jamb, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. as counters of any radious etc laid over20 mm thick screed bed in CM ( 1:4) inclding demolition of existing stone slab of any description complete all as specified and directed. 35 S & F Machine cut cuddappa stone 30 to 40 mm thick one side polished as in kitchen platformand partition wall of slab etc bedded & jointed in CM (1 : 3) including taking down existing stone slab etc complete all as specified and directed. 36 S&F in repairs vitreous china wash down water closet pan, Pedestal white, including fixing bolts etc including PVC seat cover white with flat bottom including MS, CP or aluminium anodised hinge devices including PVC low level flushing cistern 10 Ltr capacity with all internal fitting, inlet, outlet pipe connections etc. complete all as specified and directed. 37 S&F in repairs vitreous china, squatting pan, Orissa pattern, size 580 x 440 mm white, with integral foot rest, including concrete bedding and PVC flushing cistern 10 Ltr capacity including all internal fitting, inlet, outlet pipe connections etc. complete all as specified and directed. 38 S & Fin repair vitreous china wash basin white flat back of size 550 mm x 400 mm including32 mm dia CP waste coupling long screw, chain and plug and PVC waste pipe including CI brackets, etc. complete in repairsall as specified and directed by Engineer-in-Charge 39 M&Lfor providing and fixing CP toilet fitting in repairs as specified and as directed by the Engr -in-Charge for the following:-. 40 Bib taps CP 15mm bore fancy type with wall flange conforming to CAT No. CON- 037 Jaquar/ 9206 (CASA) of Prayagcomplete all as specified and directed. 41 Soap dish CAT No. ACN-1131N Jaquar/BA-259 of Prayag complete all as specified and directed. 42 CP towel rail 20mm dia and600mm long including brackets conforming to CAT No. ACN-111N of Jaquar/ BA-20 of Prayagcomplete all as specified and directed. 43 Health faucet CAT No. ALD-583KN of Jaquar/ BEA-85 of Prayag complete all as specified and directed. 44 S&F in repair Angular type stop cock conforming to CAT No. 053 of Jaquar/ 9210 of Prayag complete all as specified and directed. 45 CP toilet paper holder conforming to CAT No. ACN-1151N of Jaquar/ BA-38 of Prayag complete all as specified and directed. 46 CP towel ring round with round flange conforming to CAT No ACN-1121 BN of Jaquar/9218 of Prayag. complete all as specified and directed. 47 CP wall mixer 3 in 1 including telephone shower for 15mm bore of pipe conforming to CAT No.CON 281 and HSH -1939 of Jaquar/ PIS-70 and BH-73 of Prayag complete all as specified and directed. 48 S&F 2 way bib cock with wall flange conforming to CAT No. CON 041N of Jaquar complete all as specified and directed. 49 S&F Towel Rack600 mm long with lower hangers stainless steelconforming to CAT No.AEC - 1181N of Jaquar complete all as specified and directed. 50 S&F for Brass chromium plated shower rose100 dia with 235 mm long arm with or without swivel joints, including fixing to steel pipe or union Jaquarall as specified and directed by Engr-in-Charge 51 S&F in repairs Pillar taps long neck with aerator CAT No CON -021KN screwed for iron pipe and fixed complete all as specified and directed. 52 S&F inrepairs satinless steelRobe Hook (khuti) with5Hookcomplete complete all as specified and directed. 53 S&F in repair Sink Cock with swinging casted spout with aerator conforming to CAT No.SQN - 522KN of Jaquar complete all as specified and directed. 54 S&F inrepairs glass corner assembly cosisting of 5.5 mm thicksheet glassround(9 x 9 ) with stainless steel railing complete all as specified and directed. 55 S&F in repairSheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. 56 S&F 100 mm round Stainlesssteel Grating with waste hole complete all as specified and directed. 57 S&F 100mm round Stainlesssteel Grating complete all as specified and directed. 58 S & Fin repairPVC connections 15 mm size with PTMT nuts of length 600 mm ( hot and cold water .) all as specified and directed. 59 S & F in repairs PVC flexible waste pipe 32mm bore complete all as specified and directed. 60 M&L for old sizefly ash bricks, straight or curved on plan exc 6 m mean radiusbuilt in CM 1:6 complete all as spd and as directed including demolition of brick / stone wall etc complete all as specified and directed. 61 S&F in repairs PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to wall / ceiling or laid in trenches includingtaking down pipe of following size :(Note: - Quoted rates shall be deemed to be inclsive of necessary scaffolding / security measures as the work to be carried out for elvated up to 15 mtr height Building .) 62 (a) 110 mm bore 63 (b) 75 mm bore 64 S&F in repairs PVC (SWR) bends any radius 110 mm bore complete all as specified and directed. 65 S&F in repairs PVC (SWR) bends any radius 75 mm bore 66 S&F PVC (SWR) vent cowl 100 mm bore complete all as specified and directed. 67 S&F PVC SWR branch piece, (Double Y) equal or unequal of 110 mm bore complete all as specified and directed. 68 S&F PVC SWR branch piece, (Double Y) equal or unequal of 75 mm bore complete all as specified and directed. 69 M&L in replacement for PVC (SWR) gully trap 125/100mm, setting and jointing with solvent cement complete all as specified and directed. 70 M & L in replacement PVC (SWR) floor trap, dia of outlet 75mm, plain with grating including jointing with solvent cement complete all as specified and directed. 71 M&L for 110mm PVC (SWR) WC connector with lip ring complete all as specified and directed. 72 M&L for 75 mm PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and directed. 73 M&L for 40 mmbore Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cmwith and includingcomplete fittingsall as specified and directed . 74 Refixing of old steel tubing and connections in new or old position (wall/floor/ ceilings etc) of size including taking down complete all as specified and directed. :- 75 (a) 15 mm bore 76 (b) 20 mm bore 77 S&F GI tubing medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid in floors etc. including taking down existingsteel tubingof the following sizes complete all as specified and directed. :- 78 (a) 15 mm bore 79 (b) 20 mm bore 80 (c) 25 mm bore 81 Cutting existing steel tubing and including screwing for alterations or additions for following sizes complete all as specified and directed. 82 (a) 15 mm bore 83 (b) 20 mm bore 84 (c) 25/32 mm bore 85 S & F in repairs gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of following sizes complete all as specified and directed. :- 86 (a) 15 mm bore 87 (b) 20 mm bore 88 (c) 25 mm bore 89 S&F in repairs ball valves suitable for iron pipe high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball, screwed for iron pipe and fixed of following sizes complete all as specified and directed. 90 (a) 15 mm bore 91 (b) 20 mm bore 92 (c) 25/32 mm bore 93 S&Fball valves suitable for iron pipe high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball, screwed for iron pipe and fixed of following sizes complete all as specified and directed. 94 (a) 20mm bore 95 Cuttingin stone wall for chases, pining in making good to facings where required and painting incement mortar 1:3 to ends or edges of landinsgs, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed watter tubing etc and making good , cutting not exc10cm girth as specified and directed. 96 M & L for Cleaning and removing all dirt and scale etc from tank and from the mouths of circulating pipes for the tanks of following capacity including written of date of cleaning complete . :- 97 (a)Not exc. 500 Ltrs 98 (b)Not exc. 1000 Ltrs 99 (c)Not exc. 2000 Ltrs 100 S&F, in repairs, PVCwater storage tank lid/ coverof500/1000litres Capacity fixed with PVC locking arrangements complete all as specified anddirected. 101 Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified anddirected. 102 M&L for rendering 15 mm thickin cement mortar 1:4with water proofing compound finished even and smooth without using extra cementafter M&L fordubbing out average 15 mm thick in cement mortar 1:6on irregular face of wall .( WPC shall measured and paid sepretally) 103 M&L for rendering 15 mm thickin cement mortar 1:6finished even and smooth without using extra cementafter M&L for dubbing out average 15 mm thick in cement mortar 1:6on irregular face of wall . 104 M&L for rendering 10 mm thickin cement mortar 1:4 in ceiling andfinished even and smooth with using extra cementafter M&Lfordubbing out average 15 mm thick in cement mortar 1:4on irregular face of ceiling. Note (Plaster inceiling in patches no extra payment shall be consider) 105 M&L for rendering 15 mm thick onfair faces of brick work in cement mortar 1:6 andfinished even and smooth without using extra cement complete all as specified anddirected. 106 M&L for rendering 15 mm thick onfair faces of brick work in cement mortar 1:4with water proofing compound finished even and smooth without using extra cement .( WPC shall measured and paid sepretally) complete all as specified anddirected. 107 M&L for rendering 15 mm thick onfair faces of brick work/ concrete surfacein cement mortar 1:4with water proofing compound finished even and smooth withusing extra cementat Chhajja and above wallafter M&L for dubbing out 15 mm thickin cment mortar 1:4 on irrugular surface.( WPC shall measured and paid sepretally)(Note: - Quoted rates shall be deemed to be inclusive of necessary scaffolding / security measures as the work to be carried out for elvated up to 12 mtr height Building .) 108 Supply only Integral waterproofingcompound 109 M&L for preparatio of newplastered surface of wall and applying two coats ofdistempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification.Over andincluding 2 mm thick wall care putty over plastered surface to prepare the surface even and smooth complete all as spd and as directed. 110 M&L for preparation of newsurface of ceiling andapplying 2 coats of oil bound distemper over 2 mm thick wall care puttycomplete all as specified anddirected. 111 M & L for preparation of surface of any description new plastered ,over 10 cm width or girth including and applying two coats ofexterior weather paint complete all as specified anddirected. 112 M&L for preparation of old decorative surfaces of wall incl, cornices (plastered or unplastered)of any description, sand papered , and dusted incl complete removal of existing surface of walland applying two coats of Oil Bound distemper over coat of 2mm thck wall care putty complete all as specified and directed 113 M&L cement concrete type B01:2:4 using (12.5 mm graded aggregate) , as in roof kerbs , rounded chamfered on edges , in lintel upto 1.5 m clear span, cill, steps, seismic and other similar bands, plinth courses string courses, lacing courses , copings kneelers, apexincludingweathering , slightly rounded or chemfered angles and throatingetc.necessary form workincluding demolation of existingconcrete complete all as specified anddirected. 114 M&L for 75 mm thick Cement concrete type C1, 1:3:6 (using 20 mm gradedaggregate)as in flooring/ Plinth protection Finish even & smoothwith extra cement complete including demolition of existing concrete complete all as specified anddirected. 115 Removing building materials etc. (other than spoil payable under items 03028 to 03031 in Section-3—Earthwork) to a distance ofexc 5 Km or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified anddirected. 116 M &L for preparation of new steel surface & applying two coats of synthetic enamel to steel surface of any description over 10 cm in width or girth not otherwise described over a coat of red oxide primer complete all as specified anddirected. 117 M&L for preparation of old painted wooden surfaces exe 10 cm width or girthand applying one coat of synthetic enamel paint complete all as specified anddirected. 118 S&Fin repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers ,and wastes coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,bowl size 560 mm x 460 mmincluding coupling complete all as specified anddirected. 119 Taking down chowkats or frames wooden/steel with shutters (w/o taking off shutters from frames) n.exc 1.5 Sqm each complete all as specified anddirected. 120 Taking down /cutting steel windows shutter by means of gas cutter w/o disturbing of sofit/jambs/cills etc of any description n exc 1.5 sqmcomplete all as specified and as directed. 121 S&Faluminium powder coatedthree track sliding window with two or more shutters with & including4 mm thick tinted glass, one shutter of stainless steel mosquito proofing with good qualitybearing,handle, lock etc using PVC beadingetc using following sections of `Jindal Aluminum Ltd or equivalent in Ajit India Pvt Ltd or Crystal Bombay, as approved. fixing to stone masonary walls with & including Ist class teak wood plugs of size 20mmX20mm at an interval of 0.5m alround the track including drilling holes.(a) Frame bottom 20620(b) Frame top& side 20621(c) Shutters top & bottom 20844(d) Shutter inter lock 20724(e) Handle (Side ) for 20606 shutters, (f) Glazing Clips 19352 122 S&Faluminium powder coatedventilators/louvers 5mm thick x10cm wide frosted glass strips and following aluminium powder coated sec conforming to catalogue of JINDAl or of equivalent make and rubber beading etc all as directed :- (a) SP- 20048 (b)Glazing clips 19352 123 S & F solid PVC door frame of size 50 mmx47mm made out of 5 mm plain colour PVC sheet rainforced with MS tube suppling and fixing in opening complete all as per specification and drgs. 124 S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails.M.S frame shall be covered with heat moulded plain colourPVC C channel having a PVC sheet strip of 20 mm widthstuck inside with solvent cement for stylesplain colourPVC sheet for top rail , lock rail & bottom rail either side & as gap isert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & railswit sutable PVC beading and jointed together with solvent cement ,suppling and fixing in the frame at site as perSSR Pt-I specification & drawing complete all as specified anddirected. 125 S&F 200mm Alu. Anodised barrel tower bolt of extruded sec complete all as specified anddirected. 126 S&F 100mmsize Steel butt hinges ,medium weight, cold rolledcomplete all as specified anddirected. 127 S&F 150 mm Alu. Anodised handle, fabricated type complete all as specified anddirected. 128 M&L Preparation of Old painted Steel and iron surfacesof any description, not otherwise described, over 10 cm width or girth and applying one coats of Synthetic enamel paint complete all as specified anddirected.
