Tender For Open Gym And Horticulture Work In The Park Behind Ward-65 Awas Vikas Bullet Agency. - Excavation In Foundation In Ordinary Soil (Loam, Clay Or Sand) Including, Lift Upto 1.50 M And Lead Upto 30M And Including Filling Watering And Ramming Of Exc, bareilly-Uttar Pradesh

Tender For Open Gym And Horticulture Work In The Park Behind Ward-65 Awas Vikas Bullet Agency. - Excavation in foundation in ordinary Soil (Loam, Clay or sand) including, lift upto 1.50 M and lead Upto 30m and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-in-charge upto a distance of 30.0m from the foundation trencches. excluding royalty.( S.I. No.251) 2 Providing and laying cement concrete in 1:4:8 (1 cement : 4 coarse sand : 8 stone ballast 40 mm gauge) and curing complete, including cost of form work in foundation and floors-completion of the work as per direction of E/ I. (S.I No. 281) 3 First class B/w in 1:4 Cement Csand mortor in F/P including supply of all meterial labour T&P etc required for proper completion of work. 4 12 mm thick plaster in 1:5 cement & csand mortor over brick work minimum thickness not less then 10 mm including all supply of meterial , Labour T&P etc required for proper completetion of the work. 5 Finishing wall with Acrylic smooth exterior paint of required shade new work ( two or more coat applied @1.67ltr./10 sqm over and including priming coat of exterior primer applied @2.20 kg/10 sqm ) as per D.S.R.No. 13.46.1 6 Cement Concrete with 2cm gauge approved stone ballast, approved coarse sand and cement in proportion of 1:2:4 including supply of all material labour and T&P etc. required for proper completion of the work. 7 Earth work for filling or embankment in ordinary soil earth work in filling or embankment to be in 20 cm layers, including ,watering ,Dressing ,compacting ,ramming the soil to achive 95% proctor density ,and dressing the surface to be required levels and slope and also including 1.50m lift and 30 m lead . The earth from cutting to be used in making embankment or to be deposited as spoil banks within 30m distance as directed by the Engineer-in-charge. (Excluding Royalty) Analysis rate 8 Supply and Laying of C.C Interlocking Tiles 80mm thick in road pavement having a compressive strength not lass than 300 kg / cm2 including 40 mm thick bed of fine sand of F/M 1.25 with a specification ratio of coarse material stone grit of size 8 mm to 12 mm in ratio 2:3 and fine material port land cement & coarse sand 1 : 1 -1/2 and mix it coarse material with ratio 3:2 and top sarface of tile at least 5mm thick with mix of cement and marble dust with ratio 1:1 provide the machanical pressure of 380 kg/cm2 at the time of manifacture of tile. In the manifacture of tiles the use of cement 7.5 begs of 50 kg to 8.5 bages per m,3 and labour, including supply of all material, T&P for proper completion of the work, and joint filled with fine sand, also including as per direction of E/I (zig-zag and 20% coloured tiles) 9 S/F chest press100 NB GI B-class Pipe LEG FRAME: 32 NB GI B-CLASS Pipe MAIN FRAME: 40 NB GI B-CLASS Pipe HANDLE FRAME: 32 NB & 25 NB GI B-CLASS Pipe LEG REST: 32NB & 25NB GI B-CLASS PIPE WITH TWO HANDLES Handle cover: Nylon 66 injection moulded. SEAT & BACK REST: LLDP Roto moulded seat with inbuilt bolts 3/8 X 1.5. BOTTOM COVER: Base Cover for 100 NB-PP injection moulded (Only for Self-Standing items). STOPPER: PU ROD. 50MM DIA PIPE CAP: Nylon 66 injection moulded. BEARING CAP: Cap for 100 NB - Nylon 66 injection moulded. BEARING HOUSING AND PIN: Seamless Pipe & Round Bar BEARINGS: REPUTED MAKE (FAG/SKF) NUT BOLTS CAP: Nylon 66 injection moulded with SS M6 fasteners. POWDER COAT: DONE BY PURE POLYESTER POWDER WITH 70 80 MICRON THICKNESS. 2 Wheel/ Shoulder Twirl MAIN FRAM MADE UP 100 NB GI 10 S/F Hand Rower FRAME: 80 NB GI B- FUN ROWER SEAT HANDLE FRAME: 32 CLASS PIPES FUN WALKER FRAME: 80 NB GI B-CLASS PIPES NB GI B-CLASS Pipe LEG REST: 32NB & 25NB GI B- CLASS PIPE WITH TWO HANDLES SEAT & BACK REST: LLDP Roto moulded seat with inbuilt bolts 3/8 X 1.5. FOOT REST: LLDP Roto moulded seat with inbuilt bolts 3/8 X 1.5. 2 BOTTOM COVER: Base Cover for 100 NB PP injection moulded (Only for Self-Standing items). STOPPER: PU ROD. 50MM DIA PIPE CAP: Nylon 66 injection moulded. BEARING CAP: Nylon 66 injection moulded. BEARING HOUSING AND PIN: Seamless Pipe & Round Bar NUT BOLTS CAP: Nylon 66 injection moulded with SS M6 fasteners. BEARINGS: PERMANENT SEALED OF REPUTED MAKE (FAG/SKF) POWDER COAT: DONE BY PURE POLYESTER POWDER WITH 70-80 MICRON THICKNESS. 11 S/F Back Extention The main frame of the Back Extension is to be made in 80 NB GL. Plipes. The handle frame is to be made up of 25 NB GL. pipe which is hinged to main Frame by a suitably designed camp. Rectangular pipe of size 50x25x3 mm thick is to be provided as supportting structure for Thigh Rest. Thigh rest or seats is to be Made up of HOPE material. Footrest is to be made up of HDPE material and Attached to main frame with the help of 40 NB GL. pipes. All pipes are to be Uniformly powder coated up to minimum 60-micron thickness to avoid comosion 12 S/F Cycle 100 NB GI B- CLASS PIPES ARM FRAME: 40 NB GI B-CLASS PIPES HANDLE FRAME: 25 NB GI B-CLASS PIPES LEG REST: 32NB & 25NB GI B-CLASS PIPE WITH TWO HANDLES SEAT REST: LLDP ROTOMOULDED SEAT. POWDER COAT: DONE BY PURE POLYESTER POWDER WITH 70-80 MICRON THICKNESS. 13 S/F of Circular pull up station The main frame of Circular Pull up Station is to be made by combinations of Different size frames. The vertical support pipes have to be made by 80 NB G.I. pipes. This vertical support pipes shall give supports to the horizontal handle bars. All different size horizontal supports have to be made up of 40 NB G.I. pipes. These different sized horizontal bar supports has to be attached at different height to the vertical frame. Separate foundation stands have to be made of 80 NB G.I. pipes and G.I. plated M.S. round plates has to be provided to each support. All pipes are to be uniformly powder coated up to minimum 60- micron thickness to avoid corrosion. All open ends of pipe are to be close by GI/HDPE caps for User safety against entrapment. POWDER COAT: DONE BY PURE POLYESTER POWDER WITH 70-80 MICRON THICKNESS 14 S/F of ABS Board Double MAIN FRAME: 80 NB G.I. PIPES. INTERMEDIATE PIPE: 20 NB & 25 NB G.I. PIPE POWDER COAT: DONE BY PURE POLYESTER POWDER WITH 70-80 MICRON THICKNESS 15 S/F of Hip Twister Double Circular MAIN FRAME: 100 NB GI B- class Pipe ARM FRAME: 32 NB GI B-CLASS Pipe HANDLE FRAME: 20 NB GI B-CLASS Pipe BOTTOM COVER: Base Cover for 100 NB-PP injection moulded. TWISTER DISC: LLDP Roto moulded seat with inbuilt bolts 3/8 X 1.5, PIPE CAP: Nylon 66 injection moulded. BEARING CAP: Nylon 66 injection moulded. BEARING HOUSING AND PIN: Seamless Pipe & Round Bar NUT BOLTS CAP: Nylon 66 injection moulded with SS M6 fasteners. BEARINGS: PERMANENT SEALED OF REPUTED MAKE (FAG/SKF) POWDER COAT: DONE BY PURE POLYESTER POWDER WITH 70-80 MICRON THICKNESS. 16 S/F of Shoulder Exerciser CENTRE PIPE: 100 NB GI B- class Pipe SEAT FRAME: 32 NB GI B-CLASS Pipe MAIN FRAME: 40 NB GI B-CLASS Pipe HANDLE FRAME & LEG REST: 32NB & 25NB GI B-CLASS PIPE WITH TWO HANDLES Handle cover: Nylon 66 injection moulded. SEAT & BACK REST: LLDP Roto moulded seat with inbuilt bolts 3/8 X 1.5. BOTTOM COVER: Base Cover for 100 NB-PP injection moulded. PIPE CAP: Nylon 66 injection moulded. BEARING CAP: Cap for 100 NB - Nylon 66 injection moulded. BEARING HOUSING AND PIN: Seamless Pipe & Round Bar BEARINGS: REPUTED MAKE (FAG/SKF) NUT BOLTS CAP: Nylon 66 injection moulded with SS M6 fasteners. POWDER COAT: DONE BY PURE POLYESTER POWDER WITH 70-80 MICRON THICKNESS. 17 S/F of leg press Double CENTRE PIPE: 100 NB GI B- class Pipe SEAT FRAME: 32 NB GI B-CLASS Pipe SEAT & BACK REST: LLDP Roto moulded seat with inbuilt bolts 3/8 X 1.5. FOOT REST: LLDP Roto moulded seat with inbuilt bolts 3/8 X 1.5. BOTTOM COVER: Base Cover for 100 NB-PP injection moulded. PIPE CAP: Nylon 66 injection moulded. BEARING CAP: Nylon 66 injection moulded. BEARING HOUSING AND PIN: Seamless Pipe & Round Bar BEARINGS: REPUTED MAKE (FAG/SKF) STOPPER: PU ROD. 50MM DIANUT BOLTS CAP: Nylon 66 injection moulded with SS M6 fasteners. 2 POWDER COAT: DONE BY PURE POLYESTER POWDER WITH 70-80 MICRON THICKNESS. 18 S/F Sky/Cross walker 100 NB G.I. PIPES. FOOT REST PIPE: 40 NB G.I. PIPE FOOT REST: LLDP Roto moulded seat with inbuilt bolts 3/8 X 1.5. BOTTOM COVER: Base Cover for 100 NB-PP injection moulded. HANDLE: 25 NB CLAMPS: NYLON 66 INJECTION MOULDED CASING Handle cover: Nylon 66 injection moulded. BEARINGS: REPUTED MAKE (FAG/SKF) POWDER COAT: DONE BY PURE POLYESTER POWDER WITH 70-80 MICRON THICKNESS. 19 Supply and Instalation of Open Air Gym Outdoor Equipments including cost of loading and unloading & fixing labour as per direction by E/I 20 Supply and Placing of Doormat on the floor of open gym area including loading and unloading and labour as per direction by E/I 21 Azadirachta indicia ( Neem ) height 120-130cm in big polybag size 25 cm. 22 Polyalthia longifolia (Ashok) height 150-165 cm. in earthen pot size 25 cm. & Providing and stacking of Polyalthia pendula (Ashok Pendula) of height 150-165 cm. in earthen pots of size 25 cm as per direction of theofficer-in-charge 23 Dalbergia sissoo (Seasam) height 120-135 cm. in big poly bag size 25 cm. 24 Delonix regia (Gulmohar) height 150-165 cm. in big poly bag size 25 cm. 25 Providing and stacking of Ficus religiosa (Peepal) of height 150-165 cm. in big poly bags of size 30 cm as per direction of the officer-in-charge. 26 Providing and stacking of Phyllanthus emblica (Amla) of height 150-165cm. in Big HDPE Bag as per direction of the officer-in-charge. 27 Bauhinia purpurea (Kachnar) height 150-165 cm. in big poly bag size 25 cm. 28 Bottle palm ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bag size 25 cm 29 Sunflower hybrid well developed 15 to 20 cm ht. with fresh & healthy foliage at blooming stage in 20 cm Earthen Pot/Plastic Pot 30 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge 31 Bamboo 18 to 20 cm girth and 90 cm height

INR 708 /-

INR 5.93 Lakhs /-

FileName	File Description	File Size
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB