Tender For Special Repair To Bldg No. P 49 At Dinjan Mil Stn Under Ge Dinjan.; 1 Demolition of cement concrete in ground floor n exc 15 cm thick (un reinforced) complete all as specified and directed. 2 M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in chajjas top,laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted inmin slope 1:30 over top of chajja complete all as specified and directed. 3 Dismantling of plain or corrugated sheeting all as specified and directed. 4 S & F pre- painted galvalume aluminum zinc coating GIbased corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed. 5 S&F Pre-painted galvatume aluminium zinc coating GI basedplain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws all as specified and directed. 6 M & L for taking down wall panelling and similar work complete all as specified and directed. 7 S & F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing all as per specified and directed. 8 S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed. 9 Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets all as specified and as directed. 10 S&F for aluminium anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frameincluding providing two coats of white wash complete all as specified and as directed. 11 M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed. 12 M&L for 8mm Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately all as specified and as directed. 13 M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed. 14 M&L for preparation of old painted steel surfaces of any description, n exc 10 cm in width or girth, not otherwise described when unconnected with other painting or when painted in adifferent tintand applying one coat of synthetic enamel paint complete all as specified and as directed. 15 M&L for preparation of New painted steel surfaces of any description, n exc 10 cm in width or girth, not otherwise described when unconnected with other painting or when painted in adifferent tintand applying Two coat of synthetic enamel paint over a coat red oxide primer complete all as specified and as directed. 16 M&L for applying two coat of Synthetic enamal paint over a coat of red oxide primer on new steel based surfaces exc.10cm width or girth including preparation all as specified and directed. 17 Taking down chowkats or frame, n. exc 1.5 sqm each with shutters (without taking off shutter from the frame) all as specified and as directed. 18 Taking down chowkhats or frames with shutter (without taking off shutter from the frame) exe 1.50 & n.exc. 4 sqm in each complete all as specified & directed. 19 Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and as directed. 20 S&F for Mild steel section of flat iron fillets as in wind ties for roof sheet including drilled, securing bolt to flat iron fillets etc and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed. 21 S&F solid PVC moulded door frame of size 50mmx47mm made out of 5mm, single side prelam PVC sheet used and edges will be painted to match with printed to match with prelam sheet, reinforced with MS square tube & fixing in opening including hold fast all as specified and as directed. 22 S&F factory made solid PVC Moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face& 2 mmplain colour PVC sheet on back face, supplying and fixing in frame at site all as specified and as directed. 23 S&F 75 mm size stainless steel butt hinges medium weight cold rolled all as specified and as directed. 24 Supply and fix for 150mm long aluminium handles, cast type, anodised complete all as specified and as directed. 25 Supply and fix infor 150mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed. 26 M & L MS flat ironwork as in hold fast and similar small articles, cut to length, bent to shape, drilled hole and fixed with screw etc conforming to Fe-290 Gde-E-165 complete as specified and directed. 27 S & F pressed steel frames for door 105mm X 60mm withrevates including necessary fittingslugs, hings, lock strike plate, etc complete as specifieds, supplied and fixed complete all as specified. 28 S&F pressed steell door frame 125x60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plates comlete as specified and directed (PCC filling of holloow section measured and paid seprately) 29 M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 or E-165 all as specified and as directed. 30 S&F 30mm thick factory made Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sidesDitto, but with particle board core all as specified and as directed. 31 S & F 35mm thick factory made, 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars)edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete as specified and directed . Sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (a) all as specified and as directed. 32 Supply and fixbutt hinges 100mm long cold rolled medium weight complete all as specified and as directed. 33 Supply and fix for 150mm long aluminium handles, cast type, anodised complete all as specified and as directed. 34 Supply and fix150mm long mild steel pressed handles, oval type, stove enameled black complete all as specified and as directed. 35 S & F mild steel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200mm long all as specified and as directed. 36 Supply and fix250mm long mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed. 37 S&F in RepairFloor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor all as specified and as directed. 38 S&F door seal aluminium rod withnylon brush of approved colour fixed to shutter with and incl 20mm steel wooden screw complete all as specified and as directed. 39 M & L preparation of newuntreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paintover a coat of pink primer complete as specified and directed. 40 S & F in repairs curtain rails, harrison rail, aluminium alloy chromium plated with fixing brackets, stops, rollers etc all as specified and as directed. 41 S&Fin repairs door closer hydraulically regulated, designation No. 3, aluminium (Die cast) body, universal type (ISI marked),complete all as specified & as directed. 42 S&F powder coated aluminium anodised frame for doors, windowsetc with one or more rebates including joining cleat for fixing etc complete all as specified and directed. 43 S&F for Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified. 44 Supply and fixing 5.5mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified and as directed. 45 Supply and fixing 5.5mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified and as directed. 46 Supply and fixing 5mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified and as directed. 47 Supply and fixing of aluminium sliding window with powder coating (minium thickness of powder coating 50 micron) including following components / specification complete all as specified and directed.(i) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (ii) All vercal/ horizontal joint shall be of extruded aluminium section so as to avoid any play between jointed members. (iii) all other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, srews, etc. (iv) Stainless steel wire cloth, 036 mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples, etc. (v)Sheet glass 4 mm thick selected quality tinted/black glass and glazing with oil putty or fixed with wooden beads in square not exceeding 0.5 Sqm in each pane (vi) Rest all as specified in drawing no CEZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5, 5R/5. Note :- Grill shall be measured and paid separately. 48 Supply & fixing Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all as specified and as directed. 49 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises as directed. 50 M & L 25 mm thick PCC type B0 1:2:4 (using12.5 mm graded stone aggregate) asin leveling all as specified and directed. 51 M&L for ceramic colouredtiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:4) for laying of floor finishes complete all as specified and directed. 52 M&L for ceramic colouredtiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick backing coat in cement & sand mortar 1:3 complete all as specified and as directed. 53 M&L Non skid ceramic tiles 7 to 8mm thickarea of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm 7mm thick coloured tiles in floors etc., set and jointed in neatcement slurry and pointed in white or coloured cement to match, over screed bedding 15mm thick in CM 1:4as specified and as directed. 54 M&L for glazed ceramic tiles in vertical surface 300x450x7mm thick in dado over 10mm thick screed bed in CM 1:4 on walls set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed 55 M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floorsetc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick backing coat in cement & sand mortar 1:3 complete all as specified and as directed. 56 M&L for ceramic colouredtiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick backing coat in cement & sand mortar 1:3 complete all as specified and as directed. 57 Dismantling of stone slabs or tiles of any description or thickness as in floors, pavings, aprons, pathway etc laid dry or laid dry and pointed complete all as specified & directed. 58 M & L 75 mm thick PCC type D-2 1:4:8 ( using40mm graded stone aggregate) asin sub baseall as specified and directed. 59 M&L for prepolished, chequered cement concrete tiles of size 25cmx25cmx22mm thick, as in floors etc,including 15 mm thick screed bed or bedding in cement mortar (1:6) and set and jointedin neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and as directed. 60 M&LPre-cast (Factory casted) cement concrete Kerb stone casted in PCC (1:2:4) Type B-1 using 20mm graded stone aggregates with plan or interlocking joints (as directed)with solid blocks, exc. 10 cm in width and setting and jointedin cement mortar 1:6, complete all as specified & directed. 61 M & L for preparation of kerb stone, new un-treated concrete or plastered surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of synthetic enamel paint in black and white colour over a coat of primer complete all as specified and directed. 62 M& L for Marble work 18-20 mm thik(table rubbed and polished) (Colour- Green) in steps, jambs, pillars, window cills, cooking platforms and like in vertical surfaces in/over 10 mm thick screed bed of cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble of any shade other than white and black all as specified and directed. 63 Demolition of Brickwork or stone/boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, all as specified and as directed. 64 Material & Labour for Brick work with sub class ‘B’ old size bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) complete all as specified. 65 M&L for half thickbrick work with sub class B bricks straight or curved on plan exceeding 6m mean radius with old size bricks locaaly available built in cement mortar 1:4 complete, all as specified and as directed. 66 Taking down cement plaster on brick walls/ concrete surface, etc. including raking out joints, hacking for key, scrubbing down with water, etc all as specified and as directed. 67 M&L 15 mm thick cement plaster on wall in CM (1:6) on fair faces of brick work incl finished even and smooth without using extra cement all as specified and as directed. 68 M&L 15 mm thick cement plaster in CM (1:4) on wall( with approved water proofing compound) on fair faces of brick work incl finished even and smooth without using extra cement.Note: 1. WPC @ 2% of cement, will be paid separately.2. The rate quoted by contractor is deemed to be included necessary scaffolding and formwork as required upto 7.00 Mtr height building. 69 M&L 5 mm thick cement plaster in CM (1:3) on ceiling surfaces incl finished the surface even and smooth without using extra cement. 70 M&L for applyiing 15mm plaster with polymer modified mortar fortified with SBR(Nito Bond SBR 45) in proportion 1:3 by weight 5 litr Nitobond SBR 45 added to 50kg cement with 13 litr water and finished surfaces to existing adjoining surface of ceiling, columns, beam and like etc complete all as specified and directed 71 Supply only Integral water proofing compound all as specified and as directed. 72 M&L for complete removal of exisiting treatment of wall and applying two coat of oil bound distemper over 1mm to 1.5mm thick wallcare puttyall as specified and as directed. 73 M&L for preparation of newly plastered surfaces of walls & applying two coat of distemper oil emulsion over 1mm thickwall care putty birla white or JK & over one coat of chalk whiting priming paint complete. 74 M&L for preparation of new plastered surface of wall Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 1mm thick plaster of paris putty on new surfaces complete all as specified and as directed. 75 M&L for complete removal of existing treatment inclpreparation of old surfaces, scrubing down, washing etc from walls by scrapping with mechanical wall sander (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7/9 to make the surface free from dust, loose paint etc. and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistant as per IS-15489:2004 alkali and fungal resistant exterior paint of required shed (company depot tinted)with silicon additives 1.43 litrs/ 10 Sqm over and including primer coat of exterior primer applied 0.90 litre/10 Sqm over new surfacesincl 1mm thick plaster of paris putty, using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 mtr, the spray machine shouldbe of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and will execute the same work by authorised applicator as mentioned in PS and acessories complete all as specified and directed. 76 M&L preapring old plastered surfaces incl washing rubbing down and stopping of distempered and painted surface of ceiling and applying two coat of white wash complete all as specified and as directed. 77 M&L for Preparation of new plastered surfaces andapplying three coat of white wash on ceiling complete all as specified and as directed. 78 M&L for 75 mm thick plain cement concrete (1:3:6) Type C2 using 40 mm graded aggregates as in plinth protection/paving including finishing surface even and fair without using extra cement complete all as specified and directed 79 Forming Construction joint 30mm deep x10mm wide filled with sealing compound, Grade ‘A’ all as specified and as directed. 80 Providing precast cement concrete Type C0 (1:3:6) 12.50 mm graded aggregateas in louvres and jallies, 25mm thick (measured solid), including all mould- ings but excluding framecomplete all as specified and directed. 81 Supply and fix as in repairs rolled mild steel as in joist, channel, angle or tee section/hold fast/wind ties fixed independently with connecting base plate etc complete all as specified and as directed. 82 M&L PCC 1:3:6, C-1 (using 20 mm graded stone aggregate) as in bed blocks for inserting holdfast/ filling of steel frame, etc including necessary form work complete as specified and directed. 83 Taking up or down 15mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified & directed. 84 Taking up or down 20mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified & directed. 85 Refixing 15mm old steel tubing and connection in new or old position (wall, ceiling, floors, etc.) all as specified and as directed. 86 S & Fsteel tubing 15mm bore medium grade galvanised with all fittingsand fixed completeto wall, ceilings or laid in floors all as specified and directed. 87 Refixing 20mm old steel tubing and connection in new or old position (wall, ceiling, floors, etc.)all as specified and as directed. 88 S & Fsteel tubing 20 mm bore medium grade galvanised with all fittingsand fixed completeto wall, ceilings or laid in floors all as specified and directed. 89 Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good , cutting not exc 10cm girth complete all as specified and as directed. 90 S & F for 15mm bore CPVC tubings medium grade with all fittings & fixed complete to walls & ceilings or laid in floors complete all as specified and directed. 91 S&F in repairs for MS grating CP 75/100mm dia, without hole and with hole for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as specified and as directed. 92 S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm .complete all as specified and directed. 93 S&F wall mixer with L bend with provision for over head shower complete all as specified and as directed 94 S&F 15 mm wall mounted sink mixer regular spout with long neck as per model Casa Cat Part No 9216 of make prayag or equivalent complete all as specified and as directed 95 S & F in repairs 15 mm bore Bip taps, Chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferruleand fixed all as specified and as directed. 96 S & F in repairs, stop valves, 15 mm bore cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and directed. 97 S & F in repair , Elbows brass both ends screwed and fixed.complete all as specified and directed. 98 S & F in repairs, 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends all as specified and as directed. 99 S&F in repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges all as specified and as directed. 100 S& F as repairs brass chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union 125 mm size complete all as specified and directed. 101 S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect all as specified and as directed. 102 S&F in repairs stainless steel peg set of 6 peg, 45 cm long, complete all as specified and as directed. 103 S&F in repair soap dish of stainless steel fixed to wall with chromium plated brass screws complete all as specified and as directed 104 S&F in repairs flexible (coil shaped) PVC waste pipe for sink and wash hand basin 32/40mm dia, length not less than 70 cm, connected to PVC waste coupling/fittings complete all as specified and as directed. 105 S&F fixed in repair vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified & as directed. 106 S&F in repairs Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed. 107 S & F in repairs, 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe complete all as specified & directed. 108 S & F in repairs Vitreous china wash basin pedestal pattern, white,flat back, size 550 x 400 mm with brackets,excludingpillar cock 15 mm bore CP, PVC connection of 450 mm long including PVC(HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc complete all as specified and directed. 109 S & F 15 mm bore pillar taps, cast copper alloy, chromium plated, fancy type with capstan heads, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe all as specified and as directed. 110 Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including taking down existing water tanks complete all as specified and as directed. 111 Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including taking down existing water tanks complete as specified in SSR Part-I, all as specified and as directed. 112 S & F20 mm bore,Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) all as specified and as directed. 113 S&F as in repairs for Gun metal gate valves with iron wheel headscrewed both ends for iron pipes or for unions for 20 mm bore pipes, complete all as specified and as directed. 114 Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement and similar work complete all as specified and as directed. 115 S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts,if required: hooks (stay),heavy,for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks forhanging fans; plain angle cleats for securingpurlinstowood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed. 116 S&F 0.71 mm thick Plain Aluminium sheeting alloy 31000H4 in ridges, hip, valley gutter, crumple joint etc. complete all as specified and directed. 117 M& L for PVC (SWR) floor trap 100 dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed. 118 M& L for PVC (SWR) floor trap 75 dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed. 119 M&L for water proofing treatment on RCC roof etc. comprising with the following operation & as specified herein below:-(a)Taking down existing old tarfelt, bituminous compoundincluding cleaning & removing debris to a distance exc 100 m n.exc.250m.(b) M&L 25 thick cement concrete type B0 1:2:4 (12.5 mm graded aggregate) finished even and smooth.(c) Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight). (d) M&L for 20 mm thick screed bed in cement mortar 1:4 finished even and smooth.(e) Preparing & cleaning of fully dried cement plastered surface.(f) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 liters per sqm conforming IS-3384.(g) A layer of APP based polymeric membrane3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyester non woven fabric(weighing not less than 160 gms/sqm) shall be applied over bituminous primer as specified above.Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction.(h) One coat of aluminium paint over APP membrane @0.11Kg/Sqm.Note:-Prior to execution of the APP Membrane works, leak proof test shall be done by ponding water on roof slab to minimum depth of 25 mm. The entire roof slab shall be flooded with water for 48 hours. The necessary barrier shall be made to make feasible to stagnate water for 48 hours on roof slab. 120 M&L for 20mm thick granite (of any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cookingplatform, and likein cement mortar (1:4)including pointing in white cement (1:2) using marble dust with admixure of pigment to match the shade of granite complete all as specified and directed. 121 M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. 122 M&L for cutting holes in stone /RCC/granite slabfor inserting coocking gas cylinder pipeand making good complete all as specified and as directed. 123 S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 124 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size18mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and as directed. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 125 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size18mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and as directed. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 126 S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush type as in shelves of 18mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel L Shaped brackets which should with hold as average weight of 20-30 kg and fixed with ecessary fully body threaded star headed counter sunk S.S screw, all as specified and as directed. 127 S & F stainless steel soft close hydraulic clip concealed cabinet hinges fixed with stainless steel screws complete all as specified and as directed. 128 S & F Width of flaps (when open) 40mm Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and as directed. 129 S & F 75 mm size aluminium anodised Hasp and staple, safety type with mild steel hinge pin including bolt to hinge plate and fixed with screw all as specified and as directed. 130 S & F 50mm dia polished hard wood knobs fixed with thread screw and nut complete all as specified and as directed. 131 S & F stainless steel magnetic door catched magnet of size 50 X 15mm fixed with stainless steel screw on shelf/sides wall and shutter complete all as specified and as directed 132 Febrication & fitting of modular kitchen with cabinet/ shelves & wardrobe/ cupboard made out of 18mm thick (one side decorative lamination & other side balancing lamination) PVC sheet with plano hinges including providing cabinet for keeping baskets / cutlery basket with handles / door shutters complete all as specified and directed.Note :- PVC sheet, fitting & fixture will be measured and paid separetely as supply only. 133 Suppy only of 18mm thick UV coating, HDHMR board exterior grade, including acrylic high gloss sheet of 3mm thick over HDHMR board,anti fungal,moisture resistence,anti borer, as per IS 14587 for frame and shutter for kitchen cabinets/Cupboards etc. complete all as specified and as directed. 134 Supply & Fixing125 mm dia oval shape brass handle fancy type bright finish complete all as specified & directed. 135 Supply & Fixing stainless steel basket (plain) of approved quality of size 520 x 485 x 100 mm complete all as specified and directed. 136 Supply & Fixing stainless steel plate basket of approved quality of size 520 x 485 x 150 mm complete all as specified and directed. 137 Supply & Fixing stainless steel cup & saucer basket of approved quality of size520 x 485 x 100 mm complete all as specified and directed. 138 Supply & Fixingstainless steel glass basket of approved quality of size 520 x 485 x 150 mm complete all as specified and directed. 139 Supply & Fixing stainless steel two shelf pull out basket of approved quality of size 520 x 485 x 150 mm complete all as specified and directed. 140 Supply & Fixing ofstainless steel cutlery basket of approved quality of size 520 x 485 x 100 mm complete all as specified and directed. 141 Supply & Fixing in repair of basket/ trolly channel 500mm long extruded MS galvanised over roller as per site required to make funcontional complete all as specified and directed. 142 Demolition and breaking up 150 mm bore drain pipes, salt glazed stone ware set in cement mortar including PCC haunching and bedding, complete. 143 S&F salt glazed stone ware drain pipes of 150mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified. 144 M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW/NP2 drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed. 145 M&L for cutting into existing manholes / Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe all as specified and as directed. 146 S&F for 50mm thick steel fibre reinforced (SFRC) man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard minimum load bearing capacity 5 ton/Sqm in square, rectangular shape of size 300X300, 450X450, 600X600 complete all as specified & as directed. 147 Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed. 148 S & F Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges of thickness 1.25mm of dia 150mm complete all as specified & as directed. 149 S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors complete all as specified including dismantling of PCC & taking out old unserviceable 110mm bore PVC pipe with fittings & making good disturbed area complete all as specified & directed. 150 S &F for PVC (SWR) pipes single soketed, in any length with rubber ring joints, fixed to walls, 110mm bore pipes complete all as specified and directed. 151 S &F for PVC (SWR) pipes single soketed, in any length with rubber ring joints, fixed to walls, 75mm bore pipes complete all as specified and directed. 152 S & F for PVC (SWR) bends any radius with access door, 110mm bore complete all as specified and directed. 153 S & F for PVC (SWR) bends any radius, 110mm bore complete all as specified and directed. 154 S & F for PVC (SWR) bends any radius, 75mm bore complete all as specified and directed. 155 S & F for PVC (SWR) bends any radius with access door, 75mm bore complete all as specified and directed. 156 S&F PVC(SWR) Vent cowl 75mm dia all as specified and as directed. 157 S&F PVC(SWR) Vent cowl 110mm dia all as specified and as directed. 158 S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cementcomplete all as specified and as directed. 159 Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and as directed. 160 Taking down carefully MCB DBs any type and size by unscrewing from main switch boards/cut out boxes and removing materials to store for keeping in safe custody for reuse at site or for taking credit including sealing the cable ends and making good disturbed surface of wall etc as per existing finishes complete all as specified and directed. 161 Taking down fan, sealing cable end, dismantling blades and removing fan and keeping it in MES store for safe custody and refixing it after repair all as specified and as directed. 162 Material and labour for point wiring for One light/exhaust fan point controlled by one, one way switch with 1.5 Sqmm single core, PVC FRLS insulated unsheathed, multistranded copper conductor drawn through and includingPVC concealed including necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLSH insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth dolly suitable for modular sunken box with inner and outer cover for 01 module to 08 module as required at site complete all as specified and directed as below :-Note:-(1) Rate forCutting, chieseling and making good the existingsurface concealed wiring is deemed to be included in quoted rate by the contractor.(2) Rate for Modular sunkan boxes, inner and outer cover measured and paid separately. 163 Description all as per Ser item No.162 here-in-before but One 3 Pin 5 Amps socket out let point onindependentboard. 164 Description all as per Ser item No.162 here-in-before but One bell point controlled by one push button switch. 165 Description all as per Ser item No.162 here-in-before but one 3 pin socket outlet, 5 Amp same board. 166 Description all as per Ser item No.162 here-in-before but using 2.5 sqmm PVC FRLS insulated copper condutor wire for connecting 15A socket on independent board. 167 Description all as per Ser item No.162 here-in-before but with 4 sqmm. 168 Supply and fixing of modular switch one way 6 amps 1 module 240 Volts complete all as specified and directed 169 Supply and fixing of modularsocket outlet 2/3 pin 6 Amps 240 volts2 module complete all as specified and directed 170 Supply & fixing of modular switch one way 16 Amps1 module 240 Volts complete all as specified and directed 171 Supply and fixing of modularsocket6/16 Amps, 2/3 pin combined, 2 module complete all as specified and directed 172 S&F modular Bell push switch 6A 1 module all as specified and directed 173 Supply and fixing of modular metal flush box 1/2 module all as specified and directed 174 Supply and fixing of modular metal flush box 3 module all as specified and directed 175 Supply and fixing of modular metal flush box 4 module all as specified and directed 176 Supply and fixing of modular metal flush box 6 module all as specified and directed 177 Supply and fixing of modular white cover plate with frame 1 module all as specified and directed 178 Supply and fixing of modular white cover plate with frame 3 module all as specified and directed 179 Supply and fixing of modular white cover plate with frame 4 module all as specified and directed 180 Supply and fixing of modular white cover plate with frame 6 module all as specified and directed 181 Supply and fixing of surface mounting LED edgelit slim round downlighter made of PDC AL with huge efficient LEDs and glare free opal diffuser, IP20 including all the accessories needed for its installation all complete as directed/specified. Make havells, crompton, phillips or equivalent. cat part- SM296C LED20S-6500 PSU WH or equivalent 182 Supply and fixingof Bell electric, ding dong type240 Volts, single pole complete all as specified and directed. 183 Supply and fixing in repair of MCB Distribution board TPN double door4 Way for mountingSPN/ SP/TPN/TP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossyfinished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smoothfinish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed at site.as specified and directed by Engr-in-charge. make: havells, scneider or equivalent make: havells, scheide or equivalent 184 Supply and fixing in repair of MCB Distribution board SPN 12 Way for mountingSPN/ SP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossyfinished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smoothfinish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed. 185 Supply & fixing in repair TPN 4 Pole, 415 V, fixed type,63 Amps with breaking capacity 16 KA with connection testing and commissioning including all the accessories needed for its installation all as specified and directed. 186 Supply & fixing in repair of MCB DP 32-40 AmpsB Series 10 KA 240 volts complete all as specified and directed. 187 Supply & fixing in repair of MCB SP 6-32 AmpsC Series 10 KA, 240 volts complete all as specified and directed. 188 M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not lessthan 1.5 metres below normal ground level, connected to galvanised earth lead wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing and commissioning all as specified and directed. 189 Supply & Fixingof ceiling fan step modular step regulator ,120W, 2 module all as specified and directed. 190 Supply and fixing angular/batten holderPVC/Polycarbonate suitable for batten fittings including one inverter type LED Lamp of 9W complete all as specified and directed. 191 Supply and fixing LED fitting 1x20 watts,witn 45000 burning hr interver batten holder with min 4hr battery backup 220volts AC decorative box type with driver with aluminium housing,LED tube light conncting up to 3 core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 192 S&F LED light fitting inverter type with high ouput diffuser 2 feet, 10 watts burning hr of 45000 220 volts with min 4 hr battery backup AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable of suitable size. all as specified and directed. 193 Supply and fixing of LED wall bracket light aestheticallydesigned wall bracket light with B22d & E27 lamp holder with one lamp and with all the accessories required for its installation all as specified and directed. 194 Supply and fixing of recess mounted LED2 x 2 celing light 40W made of CRCA steel sheet housing duly powder coated with high efficacy LEDs & glare free full opal diffuser , IP20 with micro motion sensor including installation of all other accessories complete all as specified and directed. 195 Supply and fixing ofceiling rose surface PVC/Polycarbonate, 65x50 mm two to three terminals complete all as specified and directed. 196 Supply and fixing LED Bldg light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed. 197 S&F Bldg light bracket fabricated out of GI Tubing light grade 32 mm bore Bend to the shape as directed and of length 1.5 mtrcomplete with mounting MS clamp of flat iron size 40X5mm of suitable length 02 pairs incl nut bolts etc of suitable size, including taking down old corroded one all as specified and directed. 198 Material & labour for Sub main wiring with two runs of single core 6 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC conduit of adequate size fixed on surfafce of wall/ceiling with all necessary fittings and accessaries and 1 run of FRLS PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 6 Sqmm as earth wire (green in colour) run through casing capping and connected common earth dolly including taking out the old sub main wiring two run of 6 Sqmm cable one run of casing capping and one run of 2.5 Sqmm earth continuity wire for connection to DBs/dolly shall be deemed to be included in this item and shall be measured as one run complete all as specified and directed. 199 Taking down and Supply & Laying or Fixing or Passing through Pipe, XLPE insulated, Armoured, Electric Power UG Cable (Heavy Duty) with Aluminium Conductor, 1100 Volt Grade, Nominal Cross-Sectional Area 50 sqmm 4 core and Testing, including Brass Compression Cable Gland, Terminal Lug, etc including taking downcomplete all as specified and directed. 200 Excavating in Trenches not exc. 1.50 mtr wide and not exc. 1.50 mtr in depth, Taking Out and Laying of Cables, etc. and getting out in Soft/ Loose Soil, complete all as specified and as directed. 201 Returning, Filling in, including Spreading, Levelling, Watering and Well Ramming in Layers not exc. 250mm in Soft/Loose Soil, complete all as specified and as directed. 202 Removing excavated Materials (Soils) not exc. 50.00 mtr and depositing where directed at a level not exc. 1.50 mtr above the Starting Point in Soil, complete all as specified and as directed. 203 M&L Sand Cushioning (dry) in Trenches for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thick -ness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. 204 S&F LT cable cover, well burnt, laid breadth-wise along the axis of Cable laid in Trenches over Sand Cushion laid for UG Cable Protection, complete all as specified and as directed. 205 Boring under without disturbing the top surface of the road for passing through GI protection pipe 50mm bore, not exceeding 10m in single length complete all as specified and as directed. Note: Rate for Necessary machanry and assesories required for boring deemed to be includedin the quoated rate by contractor.
