Tender For Special Repair To Block No P 24 Md Accommodation At Dinjan Mil Station Under Ge Dinjan.; 1 Demolition of cement concrete in ground floor n exc 15 cm thick (un reinforced) complete all as specified and directed. 2 M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in chajjas top,laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted inmin slope 1:30 over top of chajja complete all as specified and as directed. 3 Dismantling of plain or corrugated sheeting all as specified and directed. 4 S & F pre- painted galvalume aluminum zinc coating GIbased corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed. 5 S&F Pre-painted galvatume aluminium zinc coating GI basedplain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws all as specified and directed. 6 Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets all as specified and directed. 7 S&F for aluminium anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frameincluding providing two coats of white wash complete all as specified and as directed. 8 M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed. 9 Taking down chowkats or frame, n. exc 1.5 sqm each with shutters (without taking off shutter from the frame) as directed all as specified and directed. 10 Taking down chowkhats or frames with shutter (without taking off shutter from the frame) exe 1.50 & n.exc. 4 sqm in each complete all as specified and as directed. 11 Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed. 12 S&F solid PVC moulded door frame of size 50mmx47mm made out of 5mm, single side prelam PVC sheet used and edges will be painted to match with printed to match with prelam sheet, reinforced with MS square tube & fixing in opening including hold fast all as specified and directed. 13 S&F factory made solid PVC Moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face& 2 mmplain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and directed. 14 S&F 75 mm size stainless steel butt hinges medium weight cold rolled all as specified and directed. 15 Supply and fix for 150mm long aluminium handles, cast type, anodised complete all as specified and as directed. 16 Supply and fix infor 150mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed. 17 M & L MS flat ironwork as in hold fast and similar small articles, cut to length, bent to shape, drilled hole and fixed with screw etc conforming to Fe-290 Gde-E-165 complete as specified and directed. 18 S & F pressed steel frames for door 105mm X 60mm withrevates including necessary fittingslugs, hings, lock strike plate, etc complete as specifieds, supplied and fixed complete all as specified. 19 S&F pressed steell door frame 125x60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plates comlete as specified and directed. 20 M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work all as specified and directed. 21 S&F 30mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sidesDitto, but with particle board coreall as specified and directed. 22 S & F 35mm thick, 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars)edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete as specified and directed . Sizes of members of shutters all as specified and directed. 23 Supply and fixbutt hinges 100mm long cold rolled medium weight complete all as specified and as directed. 24 Supply and fix for 150mm long aluminium handles, cast type, anodised complete all as specified and as directed. 25 Supply and fix150mm long mild steel pressed handles, oval type, stove enameled black complete all as specified and as directed. 26 S & F mild steel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200mm long all as specified and directed. 27 Supply and fix250mm long mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed. 28 Supply and fix250mm long Aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed. 29 S&F in RepairFloor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor all as specified and directed. 30 S&F door seal aluminium rod withnylon brush of approved colour fixed to shutter with and incl 20mm steel wooden screw complete all as specified and directed. 31 M & L preparation of newuntreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paintover a coat of pink primer complete as specified and directed. 32 S & F in repairs curtain rails, harrison rail, aluminium alloy chromium plated with fixing brackets, stops, rollers etc all as specified and directed. 33 S&F powder coated aluminium anodised frame for doors, windowsetc with one or more rebates including joining cleat for fixing etc complete all as specified and directed. 34 S&F Anodised aluminium powder coated window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including all necessary fittings like hinges joining cleats, glazing clips,moving roller, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified 35 Supply and fixing of aluminium sliding window with powder coating (minium thickness of powder coating 50 micron) including following components / specification complete all as specified and directed.(i) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (ii) All vercal/ horizontal joint shall be of extruded aluminium section so as to avoid any play between jointed members. (iii) all other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, srews, etc. (iv) Stainless steel wire cloth, 036 mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples, etc. (v)Sheet glass 4 mm thick selected quality tinted/black glass and glazing with oil putty or fixed with wooden beads in square not exceeding 0.5 Sqm in each pane (vi) Rest all as specified in drawing no CEZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5, 5R/5. Note :- Grill shall be measured and paid separately. 36 Supply & fixing Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening,all as specified and directed. 37 Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre peri linear metre including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 Cement : 2 Coarse sand) to match the existing floors drilling and plugging holes etc complete all as specified and as directed. 38 M & L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors all as specified and directed. 39 Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre / hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with cement mortar (1:3) & painted with white or coloured paint complete all as specified and as directed 40 Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove, dust etc. all as specified and directed. 41 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises all as specified and directed. 42 M & L 25 mm thick PCC type B0 1:2:4 (using12.5 mm graded stone aggregate) asin leveling all as specified and directed. 43 M&L for ceramic colouredtiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:4) for laying of floor finishes complete all as specified and directed. 44 M&L for ceramic colouredtiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick backing coat in cement & sand mortar 1:3 complete all as specified and as directed. 45 M&L Non skid ceramic tiles 7 to 8mm thickarea of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm 7mm thick coloured tiles in floors etc., set and jointed in neatcement slurry and pointed in white or coloured cement to match, over screed bedding 15mm thick in CM 1:4as specified and as directed. 46 M&L for glazed ceramic tiles in vertical surface 300x450x7mm thick in dado over 10mm thick screed bed in CM 1:4 on walls set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed 47 Dismantling of stone slabs or tiles of any description or thickness as in floors, pavings, aprons, pathway etc laid dry or laid dry and pointed complete all as specified & directed. 48 M & L 75 mm thick PCC type D-2 1:4:8 ( using40mm graded stone aggregate) asin sub baseall as specified and directed. 49 M&L for prepolished, chequered cement concrete tiles of size 25cmx25cmx22mm thick, as in floors etc,including 15 mm thick screed bed or bedding in cement mortar (1:6) and set and jointedin neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and as directed. 50 M&LPre-cast (Factory casted) cement concrete Kerb stone casted in PCC (1:2:4) Type B-1 using 20mm graded stone aggregates with plan or interlocking joints (as directed)with solid blocks, exc. 10 cm in width and setting and jointedin cement mortar 1:6, complete all as specified & directed. 51 M & L for preparation of kerb stone, new un-treated concrete or plastered surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of synthetic enamel paint in black and white colour over a coat of primer complete all as specified and directed. 52 M& L for Marble work 18-20 mm thik(table rubbed and polished) (Colour- Green) in steps, jambs, pillars, window cills, cooking platforms and like in vertical surfaces in/over 10 mm thick screed bed of cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble of any shade other than white and black all as specified and directed. 53 Material and labour for Machine cut kota stone slab flooring 20 to 25mm thick size not less than 22 x 22 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 20mm thick cement screed bed in cement mortar 1:3including rubbing and mirror polishing complete all as specified and as directed. 54 Material and labour for kota stone slab20 to 25mm thick in riser of steps, skirting, dado and pillarslaid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thickrendering in cement mortar 1:4including cutting, moulding outer edges,rubbing and mirror polishing complete all as specified and as directed. 55 Demolition of Brickwork or stone/boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles all as specified and directed. 56 Material & Labour for Brick work with sub class ‘B’ old size bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) complete all as specified and directed. 57 M&L for half thickbrick work with sub class B bricks straight or curved on plan exceeding 6m mean radius with old size bricks locaaly available built in cement mortar 1:4 complete all as specified and directed. 58 Taking down cement plaster on brick walls/ concrete surface, etc. including raking out joints, hacking for key, scrubbing down with water, etc all as specified and directed. 59 M&L 15 mm thick cement plaster on wall in CM (1:6) on fair faces of brick work incl finished even and smooth without using extra cement all as specified and directed. 60 M&L 15 mm thick cement plaster in CM (1:4) on wall( with approved water proofing compound) on fair faces of brick work incl finished even and smooth without using extra cement all as specified and directed.Note : 1. WPC @ 2% of cement, will be paid separately.2. The rate quoted by contractor is deemed to be included necessary scaffolding and formwork as required upto 7.00 Mtr height building. 61 M&L 5 mm thick cement plaster in CM (1:3) on ceiling surfaces incl finished the surface even and smooth without using extra cement all as specified and directed. 62 M&L for applyiing 15mm plaster with polymer modified mortar fortified with SBR(Nito Bond SBR 45) in proportion 1:3 by weight 5 litr Nitobond SBR 45 added to 50kg cement with 13 litr water and finished surfaces to existing adjoining surface of ceiling, columns, beam and like etc complete all as specified and directed 63 Supply only Integral water proofing compound all as specified and directed. 64 M&L for complete removal of exisiting treatment of wall and applying two coat of oil bound distemper over 1mm thick wallcare putty & one coat of Primer complete all as specified and directed. 65 M&L for preparation of newly plastered surfaces of walls & applying two coat of distemper oil emulsion over 1mm thickwall care putty birla white or JK & over one coat of chalk whiting priming paint complete all as specified and directed. 66 M&L for preparation of new plastered surface of wall Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 1mm thick plaster of paris putty on new surfaces complete all as specified and directed. 67 M&L for complete removal of existing treatment inclpreparation of old surfaces, scrubing down, washing etc from walls by scrapping with mechanical wall sander (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7/9 to make the surface free from dust, loose paint etc. and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistant as per IS-15489:2004 alkali and fungal resistant exterior paint of required shed (company depot tinted)with silicon additives 1.43 litrs/ 10 Sqm over and including primer coat of exterior primer applied 0.90 litre/10 Sqm over new surfacesincl 1mm thick plaster of paris putty, using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 mtr, the spray machine shouldbe of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and will execute the same work by authorised applicator as mentioned in PS and acessories complete all as specified and directed. 68 M&L preapring old plastered surfaces incl washing rubbing down and stopping of distempered and painted surface of ceiling and applying two coat of white wash complete all as specified and directed. 69 M&L for Preparation of new plastered surfaces andapplying three coat of white wash on ceiling complete all as specified and directed. 70 M&L for applying two coat of Synthetic enamal paint over a coat of red oxide primer on new steel based surfaces exc.10cm width or girth including preparation all as specified and directed. 71 M&L for 75 mm thick plain cement concrete (1:3:6) Type C2 using 40 mm graded aggregates as in plinth protection/paving including finishing surface even and fair without using extra cement complete all as specified and directed 72 Forming Construction joint 30mm deep x10mm wide filled with sealing compound, Grade ‘A’ all as specified and directed. 73 Providing precast cement concrete Type C0 (1:3:6) 12.50 mm graded aggregateas in louvres and jallies, 25mm thick (measured solid), including all mould- ings but excluding framecomplete all as specified and directed. 74 Material and labour rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening etc. confirming to Fe 410-W (gde-E-250) quality-A and fixing complete all as specified and as directed. 75 Supply and fix rolled mild steel as in joist, channel, angle or tee section/hold fast/wind ties fixed independently with connecting base plate etc complete all as specified and as directed. 76 M&L PCC 1:3:6, C-1 (using 20 mm graded stone aggregate) as in bed blocks for inserting holdfast/ filling of steel frame, etc including necessary form work complete as specified and directed. 77 Taking up or down 15mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified & directed. 78 Taking up or down 20mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified & directed. 79 Refixing 15mm old steel tubing and connection in new or old position (wall, ceiling, floors, etc.) all as specified and directed. 80 S & Fsteel tubing 15mm bore medium grade galvanised with all fittingsand fixed completeto wall, ceilings or laid in floors all as specified and directed. 81 Refixing 20mm old steel tubing and connection in new or old position (wall, ceiling, floors, etc.) all as specified and directed. 82 S & Fsteel tubing 20 mm bore medium grade galvanised with all fittingsand fixed completeto wall, ceilings or laid in floors all as specified and directed. 83 Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good , cutting not exc 10cm girth complete all as directed. 84 S & F for 20 mm bore CPVC tubings medium grade with all fittings & fixed complete to walls & ceilings or laid in floors complete all as specified and directed. 85 S&F in repairs for MS grating CP 100mm dia, without hole and with hole for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as specified and directed. 86 S&F in repairs Mirror cabinet PVC frame of size 400 x 500 mm fixed to wall with rawl plug & stainless steel suitable size screws complete all as specified and direceted. 87 S & F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 485mm x 420mm bowl size 410mm x 330mm x 160mm all as specified and directed. 88 S&F wall mixer with L bend with provision for over head shower complete all as specified and as directed 89 S&F 15 mm wall mounted sink mixer regular spout with long neck as per model Casa Cat Part No 9216 of make prayag or equivalent from list of make complete all as specified and as directed. 90 S & F in repairs 15 mm bore Bip taps, Chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferruleand fixed all as specified and as directed 91 S & F in repairs, stop valves, 15 mm bore cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions as specified and directed. 92 S & F in repairs, 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends all as specified and as directed 93 S&F in repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges all as specified and as directed. 94 S& F as repairs brass chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union 125 mm size complete all as specified and directed. 95 S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed. 96 S&F in repairs stainless steel peg set of 6 peg, 45 cm long, complete all as specified and as directed 97 S&F in repair soap dish of stainless steel fixed to wall with chromium plated brass screws complete all as specified and as directed 98 S&F in repairs flexible (coil shaped) PVC waste pipe for sink and wash hand basin 32/40mm dia, length not less than 70 cm, connected to PVC waste coupling/fittings complete all as specified and as directed. 99 S & F in repairs, 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe complete all as specified & directed. 100 S & F in repairs Vitreous china wash basin, white,flat back, size 550 x 400 mm with brackets,excludingpillar cock 15 mm bore CP, PVC connection of 450 mm long including PVC(HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc complete all as specified and directed. 101 S & F 15 mm bore pillar taps, cast copper alloy, chromium plated, fancy type with capstan heads, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe all as specified and as directed. 102 S & Fvitreous china Semi pedestal pattern (Anglo Indian type) whiteconnection to trap P or S and flush pipe etc including seat cover and making good to disturbed surfaces of floor by filling with PCC 1:4:8 type D-2 to match with existing includingtaking down the existing old one all asspecified and as directed. 103 S&F in repairs plastic water closet seat cover white closed pattern with flat bottom and mild steel CP or aluminium hinging device complete all as specified an directed. 104 S & Fin repairs mild steel300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed 105 Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including taking down existing water tanks complete all as specified and as directed 106 S & F20 mm bore,Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed all as specified and as directed 107 S & F brass magic eye for main door, minimum wt 40gm complete all as specified and as directed 108 S&F as in repairs for Gun metal gate valves with iron wheel headscrewed both ends for iron pipes or for unions for 20 mm bore pipes, complete all as specified and as directed 109 Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement and similar work complete all as specified and as directed. 110 S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts,if required: hooks (stay),heavy,for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securingpurlinstowood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed 111 S&F 0.71 mm thick Plain Aluminium sheeting alloy 31000H4 in ridges, hip, valley gutter, crumple joint etc. complete all as specified and directed. 112 S&F wall mounted Modern kitchen Utensils Dish Rack Stainless steel (31X10X30 inches) all as specified and directed. 113 M& L for PVC (SWR) floor trap 100 dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified. 114 M& L for PVC (SWR) floor trap 75 dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified. 115 M&L for water proofing treatment on RCC roof etc. comprising with the following operation & as specified herein below:-(a) Taking down existing old tarfelt, bituminous compoundincluding cleaning & removing debris to a distance exc 100 m n.exc.250m.(b) M&L 25 thick cement concrete type B0 1:2:4 (12.5 mm graded aggregate) finished even and smooth.(c) Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight). (d) M&L for 20 mm thick screed bed in cement mortar 1:4 finished even and smooth.(e) Preparing & cleaning of fully dried cement plastered surface.(f) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 liters per sqm conforming IS-3384.(g) A layer of APP based polymeric membrane3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyester non woven fabric(weighing not less than 160 gms/sqm) shall be applied over bituminous primer as specified above.Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction.(h) One coat of aluminium paint over APP membrane @0.11Kg/Sqm.Note:-Prior to execution of the APP Membrane works, leak proof test shall be done by ponding water on roof slab to minimum depth of 25 mm. The entire roof slab shall be flooded with water for 48 hours. The necessary barrier shall be made to make feasible to stagnate water for 48 hours on roof slab. 116 M&L for Special treatment for sunken portion of WCs/Bath & toilet executed in following stage:- Stage1:-Demolition of wc including lime concrete and cemennt concrete etc and preparing of surfaces of existing sunken portion of wc`s or bath etc with wire brush to removed all loose dirts, oil grease etc including removing debries from site of work etc.Stage 2:- Providing 10mm thick plaster in CM 1:3 mixed with integral water proofing chemical of Dr Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantityall as per manufacturere`s instructions.Stage 3:- Apply Dr. Fixit Premeseal primer or equivelent of STP Ltd (and allow to dry for 8 hrs) all as per manufacturer`s instructions.Stage 4:- Apply two coats of water proofing elastomeric coating system of Dr Fixit Raincoats with DFT 100 micron or shilicry 215 of STP (The surfaces after painting one coats shall be allowed to dry for 6 hrs before next coats) Stage 5:-Rendering 10mm thick in CM 1:3 mixed with integral water proofing chemical of Dr Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantityall as per manufacturere`s instructions. Stage 6:-All CI joints shall be filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr. Fixit pidicrete URP all as per manufacturer`s instructions.Stage 7:- Making holes in walls and fixing 600mm long 40mm dia medium grade GI spouts for draining of excess water if any. Stage 8:-Carryout ponding testfor 48 hrs to ensure water tighteness of repaired sunken portion and filling of sunken portion for cement concrete Type E2, 1:5:10 using 40mm graded stone aggregate as in lean concrete complete all as specified and directed. Note:- only plan area shall be measured for payment under this items. (b)Depth of suken portion of WC`s/ bath shall be upto 35 CM which is to be taken into account while coating the rate against this item.(c)The rate shall be quoted by contractor shall be deemed to be included for all the horizontal and verticl treated surface of sunken portion of WC`s/baths all as specified and as directed 117 M&L for 20mm thick granite (of any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cookingplatform, and likein cement mortar (1:4)including pointing in white cement (1:2) using marble dust with admixure of pigment to match the shade of granite complete all as specified and directed. 118 M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. 119 M&L for cutting holes in stone /RCC/granite slabfor inserting coocking gas cylinder pipeand making good complete all as specified and as directed 120 Demolition ofcement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed. 121 Material and labour for RCC (1:2:4) type B-1 (using 20 mm graded broken stone aggregate) as in slab supported on walls, beams and column in floors, roof landings, balconies, canopies, deck slabs and in shelvescomplete all as specified and as directed. (Note : Reinforcement shall be measured and paid seperately under relevant) 122 Material and labour TMT bar 10 mm and over cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and as directed. 123 Use and waste formwork to soffits of suspended slabs such as roof slab, floor slabs, landing covers, and similar works,for rough finished flat surfaces of concrete, thickness of slab not exc 200 mm,complete all as specified and directed. 124 Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm widecomplete all as specified and directed. 125 S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made all as specified and as directed 126 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size18mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and as directed (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 127 S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush type as in shelves of 18mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel L Shaped brackets which should with hold as average weight of 20-30 kg and fixed with ecessary fully body threaded star headed counter sunk S.S screw, all as specified and as directed. 128 S & F stainless steel soft close hydraulic clip concealed cabinet hinges fixed with stainless steel screws complete all as specified and as directed 129 S & F Width of flaps (when open) 40mm Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and as directed 130 S & F 75 mm size aluminium anodised Hasp and staple, safety type with mild steel hinge pin including bolt to hinge plate and fixed with screw all as specified and as directed 131 S & F 50mm dia polished hard wood knobs fixed with thread screw and nut complete all as specified and as directed 132 S & F stainless steel magnetic door catched magnet of size 50 X 15mm fixed with stainless steel screw on shelf/sides wall and shutter complete all as specified and as directed 133 Demolition and breaking up 150 mm bore drain pipes, salt glazed stone ware set in cement mortar including PCC haunching and bedding, complete all as specified and as directed 134 S&F salt glazed stone ware drain pipes of 150mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified and as directed 135 M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW/NP2 drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed. 136 M&L for cutting into existing manholes / Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe all as specified and as directed 137 S&F for 50mm thick steel fibre reinforced (SFRC) man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard minimum load bearing capacity 5 ton/Sqm in square, rectangular shape of size 300X300, 450X450, 600X600 complete all as specified & as directed. 138 Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed. 139 S & F Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges of thickness 1.25mm of dia 150mm complete all as specified & as directed. 140 S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors complete all as specified including dismantling of PCC & taking out old unserviceable 110mm bore PVC pipe with fittings & making good disturbed area complete all as specified & directed. 141 S &F for PVC (SWR) pipes single soketed, in any length with rubber ring joints, fixed to walls, 110mm bore pipes complete all as specified and directed. 142 S &F for PVC (SWR) pipes single soketed, in any length with rubber ring joints, fixed to walls, 75mm bore pipes complete all as specified and directed. 143 S & F for PVC (SWR) bends any radius with access door, 110mm bore complete all as specified and directed. 144 S & F for PVC (SWR) bends any radius, 110mm bore complete all as specified and directed. 145 S & F for PVC (SWR) vent cowl, 75mm bore complete all as specified and directed. 146 S & F for PVC (SWR) bends any radius, 75mm bore complete all as specified and directed. 147 S & F for PVC (SWR) bends any radius with access door, 75mm bore complete all as specified and directed. 148 S&F PVC(SWR) Vent cowl 75mm dia all as specified and as directed 149 S&F PVC(SWR) Vent cowl 110mm dia all as specified and as directed 150 S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed. 151 Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and as directed 152 Taking down carefully MCB DBs any type and size by unscrewing from main switch boards/cut out boxes and removing materials to store for keeping in safe custody for reuse at site or for taking credit including sealing the cable ends and making good disturbed surface of wall etc as per existing finishes complete all as specified and directed. 153 Taking down fan, sealing cable end, dismantling blades and removing fan and keeping it in MES store for safe custody and refix it after repair all as specified and as directed 154 Material and labour for point wiring for One light/fan point controlled by one,one way switch with 1.5 Sqmm single core, PVC FRLSH insulated unsheathed, multistranded copper conductor drawn through concealed wiring and includingPVC conduit of required size including necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLSH insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth dolly including sunken type pressed steel terminal boxes of 1.2mm thickness with plastic laminated white top sheet cover 3mm thick all as specified and as directed.(Note:-(1) Rate forCutting, chieseling and making good the existingsurface for complete concealed wiring is deemed to be included in quoted rate) all as specified and as directed. 155 Description all as per Ser item No.154 here-in-before but One bell point controlled by one push button switch. 156 Description all as per Ser item No.154 here-in-before but One 3 Pin 5 Amps socket out let point onindependentboard. 157 Description all as per Ser item No.154 here-in-before but One 3 Pin 5 Amps socket out let point on same board alongwith other suitable switchs. 158 Description all as per Ser item No.154 here-in-before but One light point controlled by two, 2 way switch. 159 Description all as per Ser item No.154 here-in-before but but using 2.5 sqmm PVC FRLSH insulated copper condutor wire for connecting 15A socket on independent board complete all as specified and as directed. 160 Description all as per Ser item No.154 here-in-before but but using 4 sqmm PVC FRLSH insulated copper condutor wire for connecting 15A socket on independent board complete all as specified and as directed. 161 Supply and fixing of switch piano flush type 240 Volts 5 Amps, SP, one way complete all as specified and as directed. 162 Supply and fixing of switch piano flush type 240 Volts 5 Amps, SP, two way complete all as specified and as directed. 163 Supply and fixing of bell push piano flushtype one way 240 Volts, 5 Amps all as specified and as directed. 164 Supply and fixing of switch socket combination 3/5 Pin, 2 in 1, 5 Amps, 240 volts flush type (non shuttered) complete all as specified and as directed. 165 Supply & fixing of socket outlet 2 in 1, 3/5 pin 5 Amps, 240 Volts,flush type (non shuttered) complete all as specified and as directed. 166 Supply and fixingof switch socket out let combination multipurpose 3/5 pin, 15/16 Amps and (with 3 pin 5 Amps outlet also) flush type (non shuttered) complete all as specified and as directed. 167 Supply and fixingof bell electric, ding dong type240 Volts, single pole complete all as specified and directed. 168 Supply & Fixingof ceiling fan regulator electronic, Deluxe,rotary, step type, 120/280 volts all as specified and as directed. 169 Supply and fixing angular/batten holderPVC/Polycarbonate suitable for batten fittings including one inverter LED Lamp of 9W complete all as specified and as directed. 170 Supply and fixing ofceiling rose surface PVC/Polycarbonate, 65x50 mm two to three terminals complete all as specified and as directed. 171 Supply and fixing inverter LED fitting 1x18 watts, with 45000 burning hr 220volts AC decorative box type with driver,holder and aluminium housing with Burning hr of 45000 withLED tube light conncting up to 3 core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. 172 S&F LED light fittingtype with high ouput diffuser 2 feet, 10 watts 220 volts AC inverter type with aluminium housing driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable of suitable size all as specified and as directed. 173 S&F LED building light fitting 35W 230 volts AC outdoor tye with high pressure die cst aluminium hostng and heat resistant complete with driver, lamp baacket with impact and corrosin resistant including thermal management in multiple optics complete all as specified and as directed. 174 Supply and fixing in repair of MCB Distribution board TPN 4 Way for mountingSPN/ SP/TPN/TP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossyfinished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smoothfinish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and as directed. 175 Supply and fixing in repair of MCB Distribution board SPN 8 Way for mountingSPN/ SP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossyfinished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smoothfinish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and as directed. 176 Supply & fixing in repair 415 Volts 10KA C curve miniature circuit breaker(MCB)TPN 63 AMP in the DB complete with connection testing and commissioning all as specified and as directed. 177 Supply and fixing 240V, 10 KA B curveminiature circuit breaker (MCB)SPN and current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissioning all as specified and as directed. 178 Supply & fixing in repair of MCB SPN 32 AmpsC Series 10 KA 240 volts complete all as specified and as directed. 179 Supply & fixing in repair of MCB SP 6-32 AmpsC Series 10 KA, 240 volts complete all as specified and as directed. 180 Material and labour for earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick, burried directly in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanised wire of dia 4 mm as earthing lead by means of nuts, bolts and washers of galvanised iron and earth lead protected by galvanised iron pipe 15 mm bore (light grade) and connected to earth test point and including cement concrete pit in PCC (1:3:6) type C-1(using 20 mm graded aggregate) and pre-cast RCC cover slab of size 540 x 540 x 50 mm thick, reinforced with 8 mm dia TMT bars both ways and one handle for lifting made with 10 mm dia mild steel bar,funnel, wire mesh 20 mm bore galvanised (light grade) for watering, charcoal and salt in alternate layers including necessary execuation and eath works in any types of soil complete all as shown on Electrical plate No 3 of MES SSR-I including taking out the old earthing material complete all as specified and as directed. 181 Taking down old unsv submain wiring and Material & labour for Sub main wiring with two runs of single core 6 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC conduit of adequate size fixed on surface of wall/ceiling with all necessary fittings and accessaries and 1 run of FRLSH PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 6 Sqmm as earth wire (green in colour) run through PVC Conduit and connected common earth dolly including taking out the old sub main wiringfor connection to DBs/dolly shall be deemed to be included in this item and Two runs of 6 Sq mm as current carrying conductor and one run of6 Sq mm as earth conductor PVC conduit shall be measured as one run for measurement, complete all as specified and as directed. 182 Taking down old unsv cable and Supply and laying and testing cable, XLPE insulated,screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables(heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 sq mm 3½ core all as specified and as directed. 183 Excavating in Trenches not exc. 1.50 mtr wide and not exc. 1.50 mtr in depth, Taking Out and Laying of Cables, etc. and getting out in Soft/ Loose Soil, complete all as specified and as directed. 184 Returning, Filling in, including Spreading, Levelling, Watering and Well Ramming in Layers not exc. 250mm in Soft/Loose Soil, complete all as specified and as directed. 185 Removing excavated Materials (Soils) not exc. 50.00 mtr and depositing where directed at a level not exc. 1.50 mtr above the Starting Point in Soil, complete all as specified and as directed. 186 M&L Sand Cushioning (dry) in Trenches for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thick -ness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. 187 S&F LT cable cover, well burnt, laid breadth-wise along the axis of Cable laid in Trenches over Sand Cushion laid for UG Cable Protection, complete all as specified and as directed. 188 Boring under without disturbing the top surface of the road for passing through GI protection pipe 50mm bore, not exceeding 10m in single length complete all as specified and as directed. Note: Rate for Necessary machanry and assesories required for boring deemed to be includedin the quoated rate by contractor.
