Tender For Annual Rate Contract For Civil Maintenance Works In Sector C Of Bvfcl Township For 12 Months.; 1 Civil Items 2 Earth work in excavationby mechanical means (Hydraulic Excavator)/ manual means over areas (exceeding 30 cm in depth, 1.50M in width as well as 10 Sqm on plan) including disposal of excavated earth lead up to 50M and lift upto 1.50m and disposedearth to be levelled and neatly dressed : (a) All kind of soil 3 Earth work in excavationby mechanical means (Hydraulic Excavator)/ manual means over areas (exceeding 30 cm in depth, 1.50M in width as well as 10 Sqm on plan) including disposal of excavated earth lead up to 50M and lift upto 1.50m and disposedearth to be levelled and neatly dressed :(b) In or under foul condition including pumping out water as required 4 Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.50m 5 Supplying & filling in plinth with river sandunder floors including watering, ramming, consolidation and dressing complete 6 Supplying and stacking of sandy gravel in measurable stack and then spreading at working watering, ramming, consolidation and dressing complete as per the direction of Engineer-In-charge. 7 Surface dressing of the ground including removing vegetation and inequalitiesnot exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift up to 1.5 m. All kinds of soil 8 Engazement of Mechnical excavator ( Tyremounted) with bucket capacity of 0.30 CUM including the cost of fuel, lubricant, driver & helper. 9 Mechanical carriage of excavated earth, dismantled building materials, grasses, shrubs and other rubbish including loading, unloading and stacking / spreading at designated site within Township area - 20% void shall be deducted. 10 Dismantling RCC works including stacking of reclaimed MS reinforcement & disposal of unserviceable materials up to a distance of 50 M lead outside the periphery of area cleared 11 Dismantling CC works manually/by mechanical means including disposal of unserviceable materials up to a distance of 50 M lead as per direction of engineer-in-charge. Nominal mix 1:3.:6 or richer mix(including equivalent design mix). 12 Dismantling brick work manually / by mechanical means in cement mortar including stacking of serviceable materials and disposal of unserviceable materials upto a distance of 50 m lead as per the direction of EIC. 13 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 m lead 14 Removing mortar and cleaning bricks including stacking within a lead of 50M (stacks of cleaned bricks shall be measured) 15 Providing & laying in position specified grade of cement concrete excluding the cost of centering, shuttering - all work upto plinth level CC 1:2:4 (1 cement : 2 river sand : 4 stone aggregate 20 mm nominal size) 16 Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement - 1:2:4 (1 cement : 2 river sand : 4 stone aggregate 20 mm nominal size) 17 Providing and laying in position cement concrete of specified grade CC 1 : 3 : 6 ( 1 Cement : 3 river sand : 6 Stone aggregate 20mm nominal size) excluding the cost of centering & shuttering - All work upto plinth level . 18 Providing and laying in position cement concrete of specified grade CC 1 : 4 : 8 ( 1 Cement : 4 river sand : 8 Stone aggregate 40 mm nominal size) excluding the cost of centering & shuttering - All work upto plinth level 19 25 mm cement concrete flooring 1:2:4 (1 cement : 2 river sand : 4 stone aggregate 12.50 mm nominal size) finished with a floating coat of neat cement .. May be used as plinth protection & foot path 20 Reinforcement for RCC work includingbending, binding and placing in position complete 21 Providing & fixing up to first floor level precast reinforced cement concrete 1:2:4 (1 cement : 2 river sand : 4 stone aggregate) including finishing and plastering with cement plaster 1:3 (1 cement : 3 local river sand) of thickness not exceeding 6 mm on exposed surface to give a smooth and even surface, excluding the cost of centering & shuttering and reinforcement : (a) Kerbs, steps, slabs and the like. 22 Centering and shuttering including strutting, propping etc and removal of form work for: (a) Foundation, footings, bases of columns etc. for mass concrete 23 Centering and shuttering including strutting, propping etc and removal of form work for:(b) Columns, piers, abutments, posts and struts 24 Centering and shuttering including strutting, propping etc and removal of form work for:(c) Lintels, beams, plinth beams, girders, bressumers and cantilever 25 Pucca brick work in foundation and plinth using common burnt clay local best quality bricks in cement mortar 1: 6 (1 cement : 6 river sand) including curing etc. complete 26 Extra for brick work with local best quality bricks in superstructure above plint & up to floor 5 level in all shapes & sizes in cement mortar 1: 6 (1 cement : 6 river sand) including curing etc. 27 Half brick masonary with local best quality bricks in superstructures above plinth level upto floor five level in cement mortar 1: 4 (1 cement : 4 river sand). . 28 12 mm cement plaster of mix 1 : 6 (1 cement : 6 river sand) at all height . 29 15 mm cement plaster of mix (a) 1 : 6 (1 cement : 6 river sand) at all height 30 Neat cement punning at all height . 31 Repairing of RCC chajjas & parapet walls etc. with 12 mm cement plaster of mix 1:4 (1 cement : 4 river sand) with a floating coat of neat cement including preparation of surface at all height as per the direction of EIC. 32 Repairs to plaster of thickness 12mm to 20mm in patches of 2.50 sqm & under including cutting the patch in proper shape and preparing and plastering, finishing of walls complete including the surface rubbish to the dumping ground as per the direction of Engineer-In-Charge (a) With cement mortar 1:4 (1 cement : 4 river sand). 33 Providing and fixing 1st quality ceramic glazed walltiles (300x200) mm confirming to IS : 15622 (Thickness to be specified by the manufacture of approved make in all colours, shades, except burgundy, bottle green, black of any size as approved by EIC in skirting, riser of steps and dado over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 river sand) and joining with grey cement slurry @ 3.3 Kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 34 Providing & fixing available 1st quality ceramic glazedfloor tiles(300x300)mm (Thickness to be specified by the manufacture) of 1st quality confirming to IS : 15622 of approved make incolours such as white, ivory, grey, fume red, brown laid down of 20 mm thick cement mortar 1:4 (1 cement : 4 River sand) including pointing the joints with white cement and matching pigment etc. complete. 35 Dismantling of wooden / MS doors, windows and clerestory windows shutters of area 3 Sqm. & below including frames; hold fast etc. complete and stacking of serviceable materials and disposal of unserviceable materials up to Township maintenance store (a) Of area 3 sqm and belowstacking within 50 metres lead 36 Dismantling of wooden / MS doors, windows and clerestory windows shutters of area 3 Sqm. & below including frames; hold fast etc. complete and stacking of serviceable materials and disposal of unserviceable materials up to Township maintenance store(b) Of area beyond 3 sqmstacking within 50 metres lead 37 Taking out doors, windows and clerestory window shutters (Steel or wood) of area 3 Sqm & below including stacking at our store (a) Of area 3 sqm and below 38 Taking out doors, windows and clerestory window shutters (Steel or wood) of area 3 Sqm & below including stacking at our store (b) Of area beyond 3 sqm stacking within 50 metres lead 39 Dismantling wood work in frames, trusses, purlins and rafters up to 10 M span and 5 M height of sectional area 40 Sq CM & above including stacking the materials at our store 40 Providing wood work in frames of windows, clerestory windows and other frames, wroughed frame of locally available best quality wood and fixed in position 41 Providing wood work in frames of false ceiling, partitions etc. sawn and put up in position 42 Providing & fixing MS round or square bars at required spacings in wooden frame of windows and clerestory windows 43 Providing & fixing 15 mm GI pipes of approved quality with fittings and clamps as curtain rod including cutting etccomplete in all respect 44 Providing and fixing 40 x 3 mm flat iron hold fast 30 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedded in cement concrete block 30 x 10 x 15cm with cement concrete of mix 1 : 3 : 6 (1 cement : 3 river sand : 6 stone aggregate 20mm nominal size) 45 Providing and fixing 40 x 3 mm flat iron hold fast 20 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedded in cement concrete block 30 x 10 x 15cm with cement concrete of mix 1 : 3 : 6 (1 cement : 3 river sand : 6 stone aggregate 20mm nominal size) 46 Supplying MS Bolts & Nuts with washer of different diameter as per site requirement 47 Providing and fixing ISI marked flush door shutters confirming to IS:2202 (Part-1), non decorative type , core or block board construction with frames of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneer on both faces of shutters including black enamelled iron hinges with necessary screws of: (i) 30 mm thick 48 Providing and fixing ISI marked flush door shutters confirming to IS:2202 (Part-1), non decorative type , core or block board construction with frames of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneer on both faces of shutters including black enamelled iron hinges with necessary screws of: (ii) 25 mm thick 49 Providing and fixing ISI marked 19 mm thick water proof block board door shutters confirming to ISincluding oxidised MS hinges with necessary MS screws. 50 Providing and fixing reputed brand & manufacturer 21 mm thick PVC door shutter along with PVC door frameincluding oxidised MS hinges with necessary MS screws. 51 Repairs to flush doors shutter or cupboard shutter by fixing 3 mm ply to the damaged portion of door with nails at 100 mm C/C & use of approved quality adhesive finished smooth complete in all respect as per the direction of Engineer-In-charge 52 Providing and fixing approved quality MS pressed butt hinges bright finished with necessary screws etc. complete:(a) 125 x 65 x 2.12 mm 53 Providing and fixing approved quality MS pressed butt hinges bright finished with necessary screws etc. complete:(b) 100 x 58 x 1.90 mm 54 Providing and fixing approved quality MS pressed butt hinges bright finished with necessary screws etc. complete:(c) 75 x 47 x 1.70 mm 55 Providing and fixing approved quality MS bright finished handle with necessary screws etc. complete:(a) 75 mm 56 Providing and fixing approved quality MS bright finished handle with necessary screws etc. complete:(b) 100 mm 57 Providing & fixing oxidised approved quality MS tower bolts with necessary screws etc. complete :(a) 100 x 10 mm 58 Providing & fixing oxidised approved quality MS tower bolts with necessary screws etc. complete :(b) 150 x 10 mm 59 Providing & fixing approved quality oxidised MS sliding door bolts with nuts & bolts etc. complete:(a) 250 x 16 mm 60 Providing & fixing approved quality oxidised MS sliding door bolts with nuts & bolts etc. complete:(b) 300 x 16 mm 61 Repairs to all types of wooden doors by fixing approved quality 0.35 mm thick aluminium plain sheet to the damaged portion of door with nails at 100 mm c/c finished smooth complete in all respect as per the direction of Engineer-In-charge. 62 Renewing approved quality glass panes with putty / wooden fillets and nails where ever necessary (a) 3 mm thick @ 7.50 Kg/Sqm 63 Renewing approved quality glass panes with putty / wooden fillets and nails where ever necessary (b) 4mm thick @ 10 Kgs/ Sqm 64 Renewal of old putty of glass panes (Length) 65 Supplying & fixing new wooden fillets where ever necessary of local best quality wood 66 Providing and fixing 30 mm thick glazed shutters for doors, windows & clerestorty windows of local best quality wood using 4 mm float glass panes includingblack enamelled ISI marked MS butt hinges with necessary screws 67 Providing & fixing galvanised MS wire mesh of average width of aperture 1.40 mm with wire of dia 0.63 mm for doors and windows and clerestory windows including necessary wooden fillets, wire nails and also including removing the damaged / existing wire mesh. 68 Providing and fixing 30 mm thick wire gauge shutter using galvanised MS wire gauge of average width of aperture 1.40 with wire of dia 0.63 mm for doors and windows and clerestory windows including necessary wooden fillets, wire nails and also removing the damaged / existing wire mesh. 69 Providing & fixing 20 gauge 12 mm mesh galvanised wire netting above post plate with netting cane bead on existing frame including labour for removing the old wire netting etc. complete as per the direction of Engineer - In- Charge. 70 Providing and fixing oxidised MS Hasp & staple (safety type) conforming to IS :363 with necessary screws etc complete. a) 90 mm 71 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossedon the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 72 Providing & fixing 12 mm thick and 100 mm wide ply pelmet with locally available best quality hard woodwith bracket including fixing with 25 x 3 mm flat 10 cm long and pluge etc complete with necessary screws / nails 73 Construction of temporary urinal; of size 1.5 M x 3.0 M with jati bamboo post 1.5 M C/C with hessian cloth layer and tying with coir rope including digging holes etc. complete as per direction of EIC. 74 Providing & fixing cupboard shutter by fixing 3 mm plyover wooden frame with nails at 100 mm C/C & use of approved quality adhesive finished smooth complete in all respect as per the direction of Engineer-In- charge 75 Dismantling CGI roofing including ridges, hips valleys and gutters etc. and stacking the material within 50 M lead. 76 Dismantling AC Plain or corrugated / transparent sheets in roofing including ridges, hips, valleys and gutters etc. and stacking the material within 50 m lead 77 Providing & fixing asbestos cement 6 mm thick corrugated sheets in roofing & side cladding and fixing with GI J or L hooks, bolts & nuts 8mm dia including GI plain & bitumen washers complete at all height excluding the cost of purlins, rafters, trusses & other supporting structures at upto 60 - degree pitch (a) Height up to 5.00 M 78 Providing & fixing asbestos cement 6 mm thick corrugated sheets in roofing & side cladding and fixing with GI J or L hooks, bolts & nuts 8mm dia including GI plain & bitumen washers complete at all height excluding the cost of purlins, rafters, trusses & other supporting structures (a) upto 60 - degree pitch (b) Height above 5.00 M & upto 10.00 M 79 Providing and fixing 0.63 mm thick with zinc coating corrugated CGI sheets confirming to IS-277-1969 @ 5.70 Kg/Sqm with Zinc coating not less than 275 gm / Sqm in roofing & side cladding fix with galvaised iron J or l hooks or bolts & nuts 8 mm diameter with bitumen & GI limpet washers or with GI limpet washers filled with white lead complete excluding the cost of purlins, rafter and trusses. 80 Providing & fixing AC ridges & hips in asbestos cement sheet roofing at all height 81 Providing & fixing plain AC sheet of approved quality with necessary screws /nails etc. complete at all height (frame work to be paid separately) (a) 4mm thick sheet 82 Providing & fixing wooden beading of size 50 x 12 mm of local hard wood in ceiling to support AC plain sheet at all height including nailing at 100 mm C/C as per the direction of Engineer - In- Charge. 83 Replacement of 8 mm dia GI J or L hooks in roofing / side cladding including fitting and fixing etc all complete at all heights 84 Steel work in single section fixed with or without connecting plates but including cutting, welding, hoisting, fixing in position all complete in Tee, channels & angles etc and applying a primingcoat of approved steel primer all complete. 85 Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts,cutting rivets, welding etc. dismembering and stacking within 50 M lead 86 Providing and fixing on wall face unplasticised rigid PVC rain water pipe conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion - single socketed pipes of diameter 150 mm (a) 110MM diameter. 87 Providing and fixing on wall face unplasticised rigid PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion (a) Bend 110MM diameter. 88 Providing and fixing on wall face unplasticised rigid PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion (b) Bend 75mm mm diameter 89 Providing & fixing White vitreous china water closet squatting pan(Indian type) along with S or P trap including dismantling of oldWC seat and S or P trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. Orissa pattern WC pan (Parryware, Hindware, Jaquar, Cera and kohler only) 90 Providing & fixing a pair of white vitreous china 250 x 130 x 30 mm foot rests of standard pattern for squatting pan closet or urinal basin 91 Providing & Fixing P or S trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting & making good the walls & floors: (i) 100 mm dia. 92 Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls andfloors wherever required : (Parryware, Hindware, Jaquar, Cera and kohler only) 93 Providing & fixing white solid plastic seat with lid for pedestal type WC pan complete 94 Flushing Cistern P.V.C. 10 litre capacity (low level) (White) (with fittings, accessories and flush pipe) (Parryware, Hindware, Jaquar, Cera and kohler only) 95 Providing & fixing in position 32 mm diameter PVC (approved quality) telescopic flush pipe complete cutting & making good the walls & floors including making all the connection but excluding the cost of fittings 96 Providing & fixing approved quality white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively 97 Providing & fixing in position 60 x 45 cm plain mirror superior glass of approved quality complete with 6 mm thick hard board ground fixing to wooden cleats with CP brass screws and washer complete 98 Providing & fixing in position 600 x 120 x 5 mm glass shelf with edges round of supported on anodised aluminium angle frames CP brass brackets and guard rails complete, fixed with 40 mm long screw, rawl plug etc. complete 99 Labour rate for repairing of high / low level automatic cistern by adjusting floating valves and other internal fittings as per the direction of EIC. 100 Providing & fixing in position 400 x 120 mmapproved quality PVC shelffix to wooden cleats with screws complete 101 Providing & fixing aluminum towel rail of size 600 x 20 mm complete with aluminium brackets fixed to wooden cleats with aluminium screws etc. complete 102 Providing & fixingwhite vitreous china wash basin along including making all connections and the cost of fittings of following sizes (i) 550 x 400 mm(Parryware, Hindware, Jaquar, Cera and kohler only) 103 Providing & fixingwhite vitreous china wash basin along including making all connections and the cost of fittings of following sizes (ii) 450 x 300 mm(Parryware, Hindware, Jaquar, Cera and kohler only) 104 Providing & fixing brass stop cock of approved quality 15mm nominal bore. 105 Providing and fixing PTMT stop cock of approved quality and colour 15 mm nominal bore, 86 mm long, weighing not less than 88 gms 106 Providing and fixing PTMT stop cock of approved quality and colour 20 mm nominal bore, 89 mm long, weighing not less than 88 gms 107 Providing & fixing CP pillar tap @ 400 Gms. of approved quality of 15 mm NB 108 Providing and fixing C.P. brass bib cock of approved quality 15 mm nominal bore 109 Providing & fixing PTMT bib cock of approved quality and colour 15mm nominal bore. 110 Providing & fixing PVC waste of approved quality. 111 Providing & fixing White glazed fire clay drain board of approved size 600 x 450 x 25 mm 112 Providing and fixing Stainless Steel kitchen sink as with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040 mm bowl depth 250 mm 113 Providing & fixing heat resistant connection pipe with brass union 15 mm nominal bore of length 45Cm leangth (a) 15 mm nominal bore 114 Providing & fixing heat resistant connection pipe with brass union 15 mm nominal bore of length 45Cm leangth (b) 20 mm nominal bore 115 Providing & fixing CP brass towel ring of approved quality 116 Providing & fixing 100 mm sand cast iron grating for gully, floor or Nahani trap 117 Providing & fixing CP brass stopcock of standard design and of approved make conforming to IS:8931 (1) 15 mm NB 118 Dismantling GI pipes (External work) including excavation and refilling trenches after taking out the pipes manually / by mechanical means including stacking of pipes within 50 metres lead as per direction of EIC :(a) From 15 mm to 40mm NB 119 Dismantling GI pipes (External work) including excavation and refilling trenches after taking out the pipes manually / by mechanical means including stackibg of pipes within 50 metres lead as per direction of EIC :(b) Above 40 mm NB 120 Repairs to GI lines including trenching, cutting the old pipes, taking out the same, rethreading & back filling etc. required for refixing the same: (a) GI pipes from 15 mm to 40 mm Nominal bore. 121 Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(a) 15 mm nominal bore 122 Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(b) 20 mm nomonal bore 123 Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(c) 25 mm nominal bore 124 Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(d) 40 mm nominal bore 125 Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(e) 50 mm nominal bore 126 Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(f) 80 mm nominal bore 127 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 15 mm nominal dia Pipes 128 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 20 mm nominal dia Pipes 129 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm nominal dia Pipes 130 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 40 mm nominal dia Pipes 131 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 50 mm nominal dia Pipes 132 Making connection GI distribution branch with main, by providing & fixing tees, nuts etc. including cutting and threading the pipes, testing etc. complet.(a) 25 mm to 40 mm Nominal Bore 133 Making connection GI distribution branch with main, by providing & fixing tees, nuts etc. including cutting and threading the pipes, testing etc. complet.(b) 50 mm to 80 mm Nominal Bore 134 Providing & fixing gun metal gate valve with CI wheels of approved quality (screwed end):(a) 25 mm nominal bore 135 Providing & fixing gun metal gate valve with CI wheels of approved quality (screwed end):(b) 40 mm nominal bore 136 Providing & fixing gun metal gate valve with CI wheels of approved quality (screwed end):(c) 50 mm nominal bore 137 Providing & fixing gun metal gate valve with CI wheels of approved quality (screwed end):(d) 80 mm nominal bore 138 Providing & fixing CPVC valve of approved standard: 25 mm nominal bore 139 Providing & fixing unplasticised PVC connection pipe with brass union 15 mm nominal bore of length 45 CM length 140 Providing & fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls & floors etc. complete in all respect (internal work):(a) 15 mm nominal bore 141 Providing & fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls & floors etc. complete in all respect (internal work):(b) 20 mm nomonal bore 142 Providing & fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls & floors etc. complete in all respect (internal work):(c) 25 mm nominal bore 143 Providing & fixing Chlorinated Polyvinyl Chloride (CPVC) plumbing pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing of pipewith clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. Internal work- Exposed on wall- 15mm nominal outer dia pipes:(a) 15 mm nominal bore 144 Providing & fixing Chlorinated Polyvinyl Chloride (CPVC) plumbing pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing of pipewith clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. Internal work- Exposed on wall- 15mm nominal outer dia pipes:(b) 20 mm nomonal bore 145 Providing & fixing Chlorinated Polyvinyl Chloride (CPVC) plumbing pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing of pipewith clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. Internal work- Exposed on wall- 15mm nominal outer dia pipes:(c) 25 mm nominal bore 146 Providing & fixing (i) GI union socket 15 mm nominal borein existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 147 Providing & fixing (ii) GI union socket 20mm nominal borein existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 148 Providing & fixing (iii) GI union socket 25mm nominal borein existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 149 Providing & fixing (iv) GI union socket 40mm nominal borein existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 150 Providing & fixing (v) GI union socket 50mm nominal borein existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 151 Providing & fixing (vi) GI union socket 80mm nominal borein existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 152 Providing & fixing (i) GI plain socket 15mm nominal borein existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 153 Providing & fixing (ii) GI plain socket 20mm nominal borein existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 154 Providing & fixing (iii) GI plain socket 25mm nominal borein existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 155 Providing & fixing (iv) GI plain socket 40mm nominal borein existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 156 Providing & fixing (v) GI plain socket 50mm nominal borein existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 157 Providing & fixing (vi) GI plain socket 80mm nominal borein existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 158 Providing & fixing (i) GI elbow 15 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 159 Providing & fixing (ii) GI elbow 20 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 160 Providing & fixing (iii) GI elbow 25 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 161 Providing & fixing (iv) GI elbow 40 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 162 Providing & fixing (v) GI elbow 50 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 163 Providing & fixing (vi) GI elbow 80 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 164 Providing & fixing (i) GI reducing socket 20 - 15 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 165 Providing & fixing (ii) GI reducing socket 25 - 20mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 166 Providing & fixing (iii) GI reducing socket 40-25 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 167 Providing & fixing (iv) GI reducing socket 50-40 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 168 Providing & fixing (v) GI reducing socket 80-50 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 169 Providing & fixing (i) GI Tee 15 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 170 Providing & fixing (ii) GI Tee 20 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 171 Providing & fixing (iii) GI Tee 25 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 172 Providing & fixing (iv) GI Tee 40 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 173 Providing & fixing (v) GI Tee 50 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 174 Providing & fixing (i) GI nipple 15 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 175 Providing & fixing (ii) GI nipple 20 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 176 Providing & fixing (iii) GI nipple 25 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 177 Providing & fixing (iv) GI nipple 40 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 178 Providing & fixing (v) GI nipple 50 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required. 179 Making temporary connection for social function to be held in BVFCL township quarters as well as public buildings within the township areas by laying PVC pipes as required upto a length of 50 metre and 04 nos. of water points including the cost of all. (Duration of connection shall be for three days). 180 Dis-connection of water supply line within BVFCL township areas including cleaning of site, earth work in excavation, cutting of pipe(s), plugging of point and deposition of reclaimed serviceable materials in Township store. 181 Providing & fixingin position 40 mm dia PVC pipe of approved quality (to be used as out lets of sink, wash basin & urinal pan etc.) as per direction of EIC. 182 Engagement of manpower for miscellaneous assistance in petty civil jobs as per the direction of Engineer-In-charge 183 White washing with lime on new work (three or more coats) to give an even shade 184 White washing with lime on old work (one or more coat) to give an even shade 185 Colour washing such as green, blue or buffto give an even shade on old work (one or more coat) 186 Distempering (one or more coat) with oil bound washable distemper of approved brand & manufacture in all shades in old work to give an even shade 187 Finishing walls with water proofing cement paint of required shade , (a) Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of priming coat. 188 Applying one coat of water thinnable cement primer of approved brand & manufacture on wall surface 189 Finishing walls with water proofing cement paint of approved brand and manufature and of required shade to give an even shade: old work (one or more coats) -. 190 Applying priming coat with ready mixed pink or grey primer of approved brand & manufacture on hard & soft wood work 191 Applying priming coat with ready mixed red oxide Zinc chromateprimer of approved brand & manufacture on steel galvanised iron / steel work 192 Paintingwith synthetic enamel paint of approved brand & manufacture in all shades to give an even & smooth shade including cleaning of surface :Old wood / steel works 193 Paintingwith synthetic enamel paint (two or more coats) of approved brand & manufacture in all shades to give an even shade - new wood / steel work 194 Painting with oil type wood preservative of approved brand & manufacture on new work (two or more coats) 195 Painting with oil type wood preservative of approved brand and manufactureon old work (one or more coats). 196 Wall painting with plastic emulsion paint of approved brand & manufacture to give an even shade (one or more coat on old work). 197 Wall painting with acrylic emulsion paint of approved brand & manufacture to give an even shade (two or more coat on new work). 198 Removing white or colour wash by scraping , sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 199 Varnishing with varnish of approved brand and manufacture - two or more coats of glue sizing with copal varnish over an under coat of flatting varnish 200 French spirit polishing including cleaning of the surface of the dirt, dust and sand papered smooth - One or more coat on old work. 201 Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
