Tender For Special Repair To Bldg No P-6 Of Stn Kalimata Mandir Under Ge Narangi; 1 Dismantling floor, hearth and wall tiling including cement mortar bedding (but excluding backing), removing rubbish off the premises complete all as specified and as directed. 2 Material and labour for Glazed ceramic tiles (Coloured) 450x350x7 mm thick on vertical surfaces such as skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match Including rendering 10 mm thick cement mortar 1:4 complete all as specified and as directed. 3 Material and labour for vitrified ceramic coloured tiles of10 mm thick area of each tile exceeding 0.42 and n.exc 1.00 Sqm in floor, shelves etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 20 mm thick screed bed or bedding layer in cement mortar 1:6complete all as specified and directed. 4 Material and labour for vitrified ceramic coloured tiles10 mm thick (square/ rectangular) polished, area of each tiles exc 0.42 and n.exc 1.00sqm , in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick renderingin CM 1:4 complete all as specified and directed. 5 Dismantling of plain or corrugated steel sheeting, any gauge or any thickness in roof covering complete all as specified and as directed. 6 Material and labour for Pre- paintedhot dip aluminium Zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick (Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screwscomplete all as specified and as directed. 7 Material and labour for Pre- paintedhot dip aluminium Zinc alloy metalic coated plain steel sheet 0.50mm thick (Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws as specifiedcomplete all as specified and as directed. Note:To be executed for provision of ridges and hips. 8 Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles. 9 Material and labour for brick work with sub class B bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specifed and directed. 10 Demolition of concrete in ground floors and pavings n exc 15 cm thickness ( below or above ground level) & also removing the debris to the out side of MD land 11 Material and labour for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smoothwithout using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic jointfilling at every 3m length and at corners complete all as specified and as directed. 12 Material and labour for 25mm thick PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in floor finishing the surfaces complete all as specified and as directed. 13 Material and labour for 100mm thick PCC 1:2:4 type B2 (using 40mm graded stone aggregate) as in path/paving/hard standing and finishing the surfaces even and smooth with using exra cement complete all as specified and as directed. 14 Taking down cement plaster/cement mud plaster on brick walls etc, incl racking out joints, hacking for key, scrubbing down with water etc. 15 Material and labour for rendering 15mm thick internal in cement mortar 1:6 on fair faces of brick/concrete surfces finished even and smooth without using extra cementcomplete all as specified and as directed 16 Material and labour forrendering 15mm thick external in CM 1:4 on fair faces of brick/concrete surfaces finished even and smooth without using exta cement with usingWPC @200 ml/50 kgby the wt of cement. WPC shall be measured and paid seperately. 17 Material and labour for rendering 5mm thick in cement mortar 1:3 on fair faces of brick/concrete surfces as in ceiling finished even and smooth without using extra cement complete all as specified and as directed. 18 Supply only approved integral water proofing compound. 19 Dismantling of stone slabs and tiles of and any description or thickness as on platform, shelves, floors etc laid, bedded and pointed in any mortar . 20 Material and labour for 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match withshade of granite complete all as specified and as directed. 21 Material and labour for Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Makrna Doogri/udaipur green over RCC slab including15 mmthick screed bed 1:4 complete all as specified and as directed. 22 Material and labour for machine cut kota stone slab flooring 20-25 mm thick over cement screed base 20 mm in CM 1:6,laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete mixed with pigment to match the shade of the slab including rubbing and polishing complete 23 Material and labour for machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with including 10mm thick rendering in CM 1:3 etc set and jointed in neat cement slurry complete all as specified and as directed. 24 Taking down chowkats or frames area exceeding 1.5 Sqm but not exceeding 4 Sqm each including shutter with builders hardware (without taking off shutters from the frame) complete all as specified and as directed. 25 Taking down chowkats with shutters including builders hardware(without taking off shutters from the frame) area n.exc. 1.5 Sqm each complete all as specified and as directed. 26 Supply and fix Pressed steel frames for doors of size 125mmx60mmx1.25mm with double rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed. 27 Supply and fix factory made 30 mm thick flushshutter solid core construction with block board core & plywood face panels commercial type on both sides incl 5mm thick teakwood leaping alroundcomplete all as specified and as directed. 28 Supply and fix 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc(with out sash bar), edges of framing with plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (a) complete all as specified and as directed. 29 Supply and fix aluminium, anodised, barrel tower bolts of extruded section, 150mm long and fixed complete all as specified and as directed. 30 Supply and fix of aluminium handles, cast type anodised of 150 mm long complete all as specified and as directed. 31 Supply and fix aluminium alloy. anodised, sliding door bolt of 300 mm size with hasp, staple ( bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed. 32 Material and labour for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paints over a coat of red oxide, zinc chrome primer complete all as specified and as specified anddirected. 33 Material and labour for preparation of new wood or wood based surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over a coat of pink primer complete all as specified and as directed. 34 Supply and fix 140mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor complete all as specified and as directed. 35 Supply and fix300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed. 36 Material and labour for PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in hold fast block, including form work complete all as specified and as directed. 37 Material and labour for Plain Cement Concrete B-0 Nominal Mix 1:2:4 using 12.5 mm graded stone aggegate as in filling of hollow portion of pressed steel frames complete all as specified and as directed. 38 Supply and fixstainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel stapple etc complete all as specified and as directed. 39 Supply andfixed sheet glass4 mm thick ordinery quality and glazing with oil putty in sqaure exc 0.50 sq. m in each pane complete all as specified and directed. 40 Complete removal of existing treatment on wall surfaces by scrapping, washing & rubbing down including applying a layer 1 mm wall care (putty) for making the surface even & smooth and applying two coats of acrylic distemper over a coat of alkali resistant primer including necessary cleaning splashes of paints from window panes and floor etc complete all as specified and as directed. 41 Material and labour for preparation of new plaster surface of wall and applying 2 coats of acrylic distember over1mm thick wall care putty on wall and a coat of alkali resistant priming paint complete all as specified and as directed. 42 Material and labour for preparation of newly plastered surface of ceilingand applying three coats of white wash including preparationcomplete all as specified and as directed. 43 Material and labour for preparation of newly plastered surface of walls and applying two coat of acrylic exterior weather coat paint (Weather proof paint with quality of dust guard, anti algal and anti fungal paint with minimum 05 years performance warranty,over a coat of approved primer over 1mm thick water proof putty of same manufacturer complete all as specified and as directed. 44 Material and labour for applying two coat of acrylic exterior weather coat paint (Weather proof paint with quality of dust guard, anti algal and anti fungal paint with minimum 05 years performance warranty,over a coat of approved primer of same manufacturer complete all as specified and as directed. 45 Material and labour for complete removal of existing treatment on wall surfaces by scrapping, washing & rubbing down including applying a layer 1 mm wall care (putty) for making the surface even & smoothetc complete all as specified and as directed. 46 Supply and fix Powder coated aluminium frame for doors, windows, ventilators, partition, posts to sustain curtain rail etc with one or more rebates including joining cleat for fixing etc complete all as specified and directed. 47 Material and labour Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standardtubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitredand jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainlesssteel screws, all complete as per architectural drawings and thedirections of Engineer-in-Charge. 48 Powder coated aluminium (minimum thickness of powdercoating 50 micron) for shutters of doors, windows & ventilatorsincluding providing and fixing hinges/ pivots and makingprovision for fixing of fittings wherever required including thecost of EPDM rubber/neoprene gasket required (Fittings shall bepaid for separately) with extruded built up standard tubularMaterial and labour sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge 49 Material and labour for 12 mm thick prelaminated particle board BWA type melamine finished (both side) for fixing the panel of the partition/door including necessary fittings, gusket, angle cleats, screw etc complete all as specified and directed. 50 Supply and fixing Stainless steel railing 304 Grade any dia, complete all as specified and directed. 51 Supply and fixing Stainless steel chain 304 Grade any dia, complete all as specified and directed. 52 Dismantling structural steel work wrought iron or mild steel workincluding door, gates, of any description not otherwise provided for all as specified and dorected. 53 Supply and fix mild steel Framed work such as grills, gratings, angle iron, mild steel sheets, mild steel round bar, MS flat iron etc.. for chowkhats or doors shutters or windows etc with ends of bars shouldered and/or riveted, wlded or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanksand similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed. 54 Supply and fix Welded mild steel wire fabric n.exc 4 kg pefr sqm supplied and fixed complete to wood or steel members complete all as specified and as directed. 55 Material and labour for repair & rehabilitation of existing old damaged concrete surface of ceiling of any description as follows:- (i) Chipped offf the old damaged surfaces of structuralmember of wall/ceiling/coloums/ beams and remove the rust by passivating rust remover (Sika rurst off - 100) and applying one coat of anti corrosive treatment by zinc rich primer (Friazing R) (ii)application of two coat of sika slurry coating /Bond coat on surfaces with mixer of sika latex power: water cement in the ratio of 1:4:8 as per manufacturer instruction. (iii) Repair the surfaces by polymer morter in ration of cement and sand 1:4 and mixer of sika latex power diluted in water is 1:6 complete as per manufacture instruction and making surfaces even and smooth without using extra cement complete all as specified and directed Note: Work will be carried out in patches. Make : Sika or equivalent. 56 Material and labour for forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade A complete all as specified and as directed. 57 Taking down carefully aluminium/ copper point wiring for light/fan/ socket/bell or power point incl. all fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. complete removing materials to store for keeping in safe custodysite or handed over to contractor as schedule of credit and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed. 58 Taking down ceiling/exhaust/wall fan including connection wires carefully and deposit to MES store in safe custody complete all as specified and as directed. 59 Material and labour for point wiring with 1.5 sqmm, single core, PVC insulated and PVC unsheathedFR-LSH cable, 1100 volts grade IS-694marked, with multistranded copper conductors and earthcontinuity wire with 1.5 Sqmm copper conductor cable (including connecting to earth dolly)laid/fixed with and including PVC rigid conduit on walls/ceiling (concealed),with MS/PVC terminal boxes fixed flush with wall surface with 3mm thick masonite laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulators etc. including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly for one light or fan point controlled by one 5 Amp switch one way complete all as specified and as directed. 60 All as per item serial No 58 here-in-before but One 3 pin socket outlet 6 amps on the same board with other switches 61 All as per item serial No 58 here-in-before but One socket outlet 3 pin 6 Amp on independent board. 62 All as per item serial No 58 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable for 6 pin 15 Amp socket outlet on independent board and earth continuity wire with 2.5 sqmm cable complete all as specified and as directed. 63 Supply and fix switch modular type 6 Amp 240 Volts single one way (ISI marked) complete all as specified and as directed. 64 Supply and fix modular socket, 6 Amp 2/3 pin combined, 2 module complete all as specified and as directed. 65 Supply and fixmodular switch 1 way 16 amp, 1 module complete all as specified and as directed. 66 Supply and fixmodular socket, 16 Amp 2/3 pin combined, 2 module complete all as specified and as directed. 67 Supply and fixstepped type modular electronic fan regulator, two module size, flush type complete all as directed. 68 Supply and fixceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as specified and as directed. 69 Supply and fixmodular lamp holder ,PVC/Polycarbonate type with back plate suitablefor batten fittings complete all as specified and as directed. 70 Supply and fixmodular white cover plate with frame, 2 module complete all as specified and as directed. 71 Supply and fix modular white cover plate with frame, 4 module complete all as specified and as directed. 72 Supply and fix modular white cover plate with frame, 6 module complete all as specified and as directed. 73 Supply and fixmodular white cover plate with frame, 8 module complete all as specified and as directed. 74 Supply and fixmetal flush box 4 module for modular switches complete all as specified and as directed. 75 Supply and fixmetal flush box 6 module for modular switches complete all as specified and as directed. 76 Supply and fixmetal flush box 8 module for modular switches complete all as specified and as directed. 77 Supply and fixmetal flush box 1/2 module for modular switches complete all as specified and as directed. 78 Supply and fixing in repair LED lights fitting 1x 20W, 220V,warm white AC decorative batten type connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. 79 Supply and fixing in repairs round shape 15 watt warm white 220 volts AC surface/ recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. 80 Supply and fixing in repairs 9/10 watt or nearby in size focus light warm white 220 volts AC for surface mounted type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. 81 Supply and fix in repair LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. 82 Supply and fix in repair wall decorative fixtures in durable body and designer mesh in gold finish suitable for 9W LED lamp of B22, including lamp of 9watt complete all as specified and as directed. 83 Supply and fix single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp 240 V complete all as specified and as directed. 84 Supply and fix in repair/replacementMCCB DB IP-43 of sheet metal enclosure double door VTPN 4 way with 250 Amps rated copper bus bar 415 volt and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and as directed. 85 Supply and fix in repair/replacementMCB DB of sheet metal enclosure IP 43 double door SPN 8 way with 200 A rated bus barand grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and as directed. 86 Supply and fix in repair/replacement MCCB four pole 100A, Icu 16KA, thermal magnetic, 415v AC complete all as specified and as directed. 87 Supply and fix in repair/replacement MCBs, SP 6 to 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA,B-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and as directed. 88 Supply and fix in repair/replacementMCBs, SPN 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,B-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and as directed. 89 Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1400 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. 90 Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450m sweep, 1400 rpm with blades, and frame and louvers complete all as specified and as directed. 91 Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm burieddirectly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including galvanised earth lead wire 4 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia GI pipe connected to main control board and GI pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etcRCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate)including excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009 92 Supply and fix in repair/replacement LED 60 W building secruity light made up of pressure die cast housing with high efficient LED as lighting source and PC cover having TOP Opening separate driver compartment with IP66 protection and impact resistance of IK07 and suitable for dia upto 43 mm complete all as specified and as directed. 93 Material and labour forbuilding secruity light bracket made out of 40 mm bore light grade GI Pipe with two sets clamps, with nuts and bolts, bend to shape for fixing street light luminaries all as directed, length of GI Pipe shall not be less than 2.0 mtrs complete all as specified and directed. 94 Material and labour for Sub main wiring with 2 runs of 4.0 sqmm, single core,FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dia non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4.0 sqmm single core FR-LSHPVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and type of conduit complete all as specified and directed. Note: 2 run of 4 Sqmm cable and 1 run of 4 Sqmm cable along with conduit altogether shall be measured as one unit. 95 Material and labour forwiring with 2 runs of 6 sqmm, single core,FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith single run of 6 sqmm single core FR-LSHPVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down oldwiring and type of conduit complete all as specified and directed. Note: 2 run of 6 Sqmm cable and 1 run of 6 Sqmm cable along with conduit altogether shall be measured as one unit.
