Tender For Maint And Repair To Joinery Items And Certain Other B/R Works At Officer Md Accn Tarapore Enclave Under Age B/R-Ii Of Ge (South) Delhi Cantt-10; 1 Taking down chowkhats or frames with shutter (without taking off shutter from frame) exc. 1.5 sqm and n exc.4.00 Sqm each including make good disturb portion as the existing surfaces complete all as specified and as directed. 2 M&L for factory made pressed steel door frame of size 105mm x 60mm made out of 1.25 mm thick MS sheet with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate 12 mm bar thresh hold etc. including one shop coat of red oxide zinc chrome primer complete all as specified and as directed. 3 M&L for factory made pressed steel door frame of size 125mm x 60mm made out of 1.25 mm thick MS sheet with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate 12 mm bar thresh hold etc. including one shop coat of red oxide zinc chrome primer complete all as specified and as directed. 4 S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, with decorative face veneer on both faces with lipping/ frame to match complete all as specified and as directed. 5 S&F 100 mm stainless steel butt hinges, AISI 304 medium weight, complete all as specified and as directed. 6 S&F 200 mm stainless steel tower bolt AISI 304 complete all as specified and as directed. 7 S&F 150 mm stainless steel handles AISI 304 complete all as specified and as directed. 8 S&F 300 mm stainless steel, AISI 304 sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded complete all as specified and as directed. 9 S&F in repair for mild steel, 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed. 10 S&F Solid PVC door frame of size 50 mm x 47mm made out of 5 mm both side prelam PVC sheet used instead of plain colour PVC Sheetand edge will be painted to match with prelam sheet. reinforced with M.S. Square tube, in opening as per specifiecation and drawings complete all as specified and as directed. 11 S&F Factory made solid panel PVC Moulded door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. Clause No. 8.B.1 to8.B.10 and drawing on page No. 156 & 157 of MES SSR-2010 Part-II complete all as specified and as directed. 12 M & L for mild steel framed work as in doors or gates of angle or tubularsection with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepered for hanging or sliding with or including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete including dismantling of existing steel complete all as specified and as directed. Fe 410 - (Gde- E- 250) complete all as specified and as directed. 13 M&L for preparation of new wooden surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paintoveronecoat of pinkprimer complete all as specified and as directed. 14 M&L for preparation of new steel surfaces of any description not otherwise described over 10 cms width or girth and apply two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer all as specified. 15 Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc,complete all as specified and as directed. 16 M&L for 10 mm thick rendering with readymix plaster (as per manufaturers instruction) on face of brick or concrete surfaces finished even and smooth surface without using extra cement on wall of up to four stories bldgs complete all as specified and as directed. 17 M&L for 5 mm thick rendering on ceiling surfaces with redimix plaster (as per manufaturers instruction) on face of brick or concrete surfaces finished even and smooth surface without using extra cement on wall of up to four stories bldgs complete all as specified and as directed. 18 M&L for complete removal of existing treatment under (OBD/Oil paint/ white wash etc)by scrapping with mechanical wall sander on wall/ceiling (having mechanical vacuum mechanism) having RPM not less than 1500, sending pad of 80 grit having dia of 7/9to make the surface free from dust, loose paint , removal of nails etc and filling cracks/ holes and windows /doors jams by putty & repairs in good shape by skilled labour complete all as specified and as directed. 19 M&L for cement based putty of average thickness1-2 mm over the plastered/Old painted wall /ceiling surcafes to make the surface free from dust etc, by skilled labor as per following steps :-Step 1 :-Mix the putty powder by adding water as per manufacturer instructions and mix it with wall mixture with the mixing capacity of minimum 2.5 kg putty per minute Step 2 :-Applying the first coat of prepared mixture with the help of fully automatic airless spray machine of putty application having flow speed of maximum 6 liters per minute with a maximum pressure of 3300 PSI.Step 3 :- Allow 6-8 Hrs time to dry the putty surface. 20 M&L for applying two coats of oil bound distemper on wall/ceiling surfaces over and including one coat of primer using airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 m the spray machine should be of reputed manufacturer with Pro guard technology and capability of tracking pressure and paint usage and certified by pain manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and as directed. 21 M&L for preparation of newly plastered surfaces of wall/ceiling sufraces and applying 1mm thick (average thickness) cement based putty and thereafter apply two coats of oil bound distemper on wall/ceilingsurfaces over acoat of primer andusing Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 Mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by pain manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and as directed. 22 M&L for preparation of old plastered surfaces of wall / ceilingapplying two coats of white wash including scaffolding arrangement, trestles, ladders complete all as specified and as directed. 23 M&L for preparation of oldwooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed. 24 M&L for preparation of old painted surfaces of steel of any description over 10cm width or grith and applying one coat of synthetic enamel paint, complete all as specified and as directed. 25 S&F in repairs, centre hole wash hand basin mixing valve 15 mm bore, Hot & cold CP brass fancy including joints to steel pipe or unions including fittings complete all as specified and as directed. 26 S&F in repairs, wallmixervalve 15 mm bore Hot & cold CP brass fancy with L-bend including joints to steel pipe or unions , including fittings for, complete all as specified and as directed. 27 S&F in repairs, sink mixer valve 15mm bore Hot & cold CP brass fancy including joints to steel pipe or unions , including fittings complete all as specified and as directed. 28 S&F in repair Stainless Steel (SS304)towel Rail/Rackfixed with suitable screw complete all as specified and as directed. 29 S&F in repair corner glass shelf with chromium plated guard rails complete all as specified and as directed. 30 S&F in repair plastic WC seat cover white / off white closed pattern with flat bottom end cover and mild steel CP hinging device complete all as specified and as directed. 31 S&F in repairs, CP brass health faucet alongwith 1.00 to 1.50 meter good quality SS flexible connection pipe suitable for 15mm bore pipe, complete all as specified and as directed. 32 S&F in repair, brass spindles with knob (Each splindle having 01 x CP Knob fitted with screw) Chromium plated suitable for existing concealed stop valves/Bib tap/Hot & Cold mixer valve (for WHB/Sink/Wall) all as per sample, complete all as specified and as directed. 33 S&F in repair Vitrous china wash hand basin white, ovel type over counter wash hand basin size 550x420mm, including necessary waste pipe and coupling, wash basin to be fixed in granite counter complete all as specified and as directed. 34 S&F in repair vitreous China wash down water closet pan pedestal pattern or EWC type, white (excluding fixing bolts, flushing cistern and flush pipe) with P or S trap but including plastic water closet seal, seat cover ,white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device including connection to drain and flush pipe complete all as specified and as directed. 35 S&F in repairPVC valveless, syphonic action type, flushing cistern of 10 Ltr capacity, low level, white, with inlet, ball valve, float and handle, one number PVC connection,with brass nuts including PVC Lbend pipe fitted to WC and brackets to fix the flushing cistern with wall, complete all as specified and as directed. 36 S&F in repair PVC waste pipe 32 mm bore, 65cm long plain/ corrugated including suitable adopter, complete all as specified and as directed. 37 S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified 38 S&F steel peg set colour coated of six as per sample in repairs complete all as specified. 39 S&F in repair stainless steel grating dome 100/125 mm dia of best quality, complete all as specified and as directed. 40 S&F in repair Brass chromium plated shower rose 125mm size with arm, complete all as specified and as directed. 41 S&F in repair for stainless steel plate rack made of 1mm thick stainless steel sheetof size 975 mm x 750 mm x 210mmconsisting of 4 shelf for bowls and three shelf for keepingthen nos of big size plates, ten nos medium size plate and seven nos of small size plates divided by 10mm dia stainless steel hollow pipe @ 60mm centre to centre, complete all as specified and as directed. 42 S&F in repair Sinks with drainage board made of 1 mm thick stainless steel for kitchen or laboratory overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipeincludingPVC waste pipe 32 mm bore, 65 cm long complete all as specified and as directed. 43 S&F in repair 15 mm bore angle valve / stop cock chromium plated, cast copper alloy screwed down high pressure fancy type, chromium plated with long shank and cup (concealed type) screwed for both ends for iron or for unions complete all as specified and as directed. 44 S&F in repair Bib taps long body 15 mm bore, chromium plated cast copper alloy, fancyscrewed both ends complete all as specified and as directed. 45 S&F in repairs, PVC connection 15mm size with brass nut of length 450/600 mm for hot water pipe,complete all as specified and as directed. 46 S&F in repair toilet paper holder of vitreous china fixed to wall with chromium plated (CP) brass screws, complete all as specified and as directed. 47 S&F in repair Bevelled edge mirror of 5 to 6 mm thick selected quality glass, 900 x 600 mm size, mounted on 6 mm thick AC Building board or commercial plywood and fixed to wooden plugs with Chromium plated brass screws and cup washer complete all as specified and as directed. 48 S&F in repairs 15 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed. 49 S&F in repairs 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed. 50 S&F in repairs 25 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed. 51 Supplying and laying of CPVC 20 mm outer dia pipes SDR 11 including Plain CPVCandbrass threaded fittings SDR 11 (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.)fittings on walls/ceiling or laying in floors including all including taking down of existing GI steel tubing complete all as specified and as directed. 52 Supplying and laying of CPVC 25 mm outer dia pipes SDR 11 including Plain CPVCandbrass threaded fittings SDR 11 (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.)fittings on walls/ceiling or laying in floors including all including taking down of existing GI steel tubing complete all as specified and as directed. 53 M&L for steel water tubing of nominal bore 32-40mm medium grade galvanised with all fittings including short lengths, fixed to walls or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.)including taking down of existing GI steel tubing complete all as specified and as directed. 54 S&F Factory Made 18mm thick 100% Solid WPC (Wood polymer Composite) Laminated Board of required size for WC/Bathroom/Toilet/Kitchen and Cabinets, comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade), Calcium Carbonate and natural fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbmhaving good screw holding capacity ( Screw Withdrawal strength of 2000 N (Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2and esistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws including dismantling of existing board any type complete all as per direction of GE. Note :- (a) Pattern & design of WPC board to be decided by GE.(b) Items like, magnetic Catcher, cupboard 100mm SS handle, and CP Clip/continuous (piano) hinges,mild steel, bright finish or electrogalvanised, width of flap (when open) is 30mm, Haps & Staple deemed to be included in the quoted rate. 55 S&F Factory Made 6 mm thick 100% Solid WPC (Wood polymer Composite) Laminated Board of required size for WC/Bathroom/Toilet/Kitchen and Cabinets, comprising of virgin PVC resin of K Value 57-60 (Suspension Grade), Calcium Carbonate and natural fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbmhaving good screw holding capacity ( Screw Withdrawal strength of 2000 N (Face) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2and esistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws including dismantling of existing board any type complete all as per direction of GE. Note :- (a) Pattern & design of WPC board to be decided by GE.(b) Items like, magnetic Catcher, cupboard 100mm SS handle, and CP Clip/continuous (piano) hinges,mild steel, bright finish or electrogalvanised, width of flap (when open) is 30mm, Haps & Staple deemed to be included in the quoted rate. 56 M&L for running welding not exceeding 6 mm for iron wire mesh door and fixing of hinges of wooden flush door with iron door frame in repair including petty repairs material like screws/nails etc. to make it functional complete all as specified and as directed. Note :- Any items required to be replaced shall be paid under respective items completed all as specified and directed. 57 M&L for cleaningof PVC water storage tanks 250 litre capacity and removing waste material etc to a distance not exceeding 50 m and burrying in pits and re-filling the same including petty repairs material like sand/cement arrangement etc. to make it functional complete all as specified and as directed. 58 S&F in repair PVC water storage tanks 250 litre capacity (Rectangular with closed top) and fixed in position including PVC float valve 15 mm bore with ball & aluminum rod and fly nut complete, screwd for iron pipe inclusing dismantling of water tanks of any type/patternand removing from site complete all as specified and as directed. 59 S & F PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints fixed to wall including dismantling of existing SWR/PVC/Salt glazed ware/AC or reinforced concrete pipe set in cement mortar etc. complete all as specified and as directed. 60 S&F PVC (SWR) bend/Tee/Socket etc any radius 110mm bore pipe complete all as specified and as directed.. 61 S&F holder bat clamps 110 mm bore made out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stay to wall or roof complete all as specified and as directed. 62 PVC (SWR) pipes 75 mm bore single socketed, in any length with rubber ring joints fixed to wall including dismantling of existing SWR/PVC/Salt glazed ware/AC or reinforced concrete pipe set in cement mortar etc. complete all as specified and as directed. 63 S&F PVC (SWR) bend/Tee/Socket etc any radius 75mm bore pipe complete all as specified and as directed. 64 S&F holder bat clamps 75 mm bore made out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stay to wall or roof complete all as specified and as directed. 65 S&F in repair stainless steel wire cloth, 0.63 mm nominal dia or wire and sqm average width or aperature 1.40mm, fixed with tinned tacks or galvanised wire staples to doors / steel windows, including necessary welding work complete all as specified and as directed. 66 Demolition of stone slab and tiles of any description or thickness on cooking platform, floors, aprons etc laid bedded and pointed in any morter complete all as specified and directed 67 M&L for 25 mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor complete all as specified and as directed. 68 M&L for granite (of any type) work, 18-20 mm thk (table rubbed and polished) in steps, jambs, pillars, cooking platforms, floor, skirtings with necessary hole for gas pipe where ever required and likes over and including screed bed of 20 mm thick in cement mortar 1:6 including pointing in white cement using marble dust with admixture of pigment to match including rounded edges with shade of granite complete all as specified and as directed. 69 M&L for 10-12 mm granite stone tile (mirror polished and machin cut edge) of any colour and shade as approved by Engr-in-Charge, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of graniteincluding 10 mm thick backing coat in cement mortar 1:4), completeall as specified and as directed. Note :-Work alsoincludes in patches forinside or outside the house complete as in cooking plateform. 70 M&L for Glazed Ceramic coloured tiles in vertical surface 300X600mm / 300x450mm 7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and including 10 mm thick backing coat in cement mortar (1:4), including dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off thepremises completeall as specified and directed 71 M&L forVitrified Ceramic tiles light shade 8 -10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm Each, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete over and including 15 mm thick screed bed in cement mortar 1:6 including dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off thepremisescompleteall as specified and directed. 72 All as per srl item No 71.00 here-in-before but on vertical surfaces as in skirting including 10 mm thick rendering as backing coat to receive the tiles on fair faces of brick /concrete surfacesin cement mortar 1:4 complete all as specified and as directed. 73 Demolition of concrete (unreinforced) of any description and any position not otherwise specifically provided complete all as specified and as directed. 74 M & L for Precast RCC 1:2:4 type B-1 (20 mm graded crushed stone aggregate ) as in Drain cover slab etc complete all as specified and as directed. 75 M&L for cement concrete 1:3:6 type C2 (using 20mm graded stone aggregate) in plinth protection, 50 mm thick, finished even and rough, including M&L for machine pressed, factory made, Glossy finishedchequered cement concrete tiles 25cmx25cm x (22-25)mm thick, set jointed and pointed in neat cement slurry in floor with grey cement and pigment with 20 mm thick screed bed are bedding layer of cement mortar (1:6) for top finishes complete all as specified and as directed. 76 M&L for cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in height, coping, kneeless apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 (12.5 mm graded crushed stone aggregate) complete all as specified and as directed. 77 M&L for 75 mm thick PCC 1:4:8 Type D2 using 40 mm graded crushed stone aggregates as in foundations filling and mass concrete complete all as specified and as directed. 78 M & L for60 mm thick factorymade chamfered edge cement concrete paverblock of M-35 grade with approved colour,design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer throughvibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. 79 M&L for machine pressed, factory made, Glossy finishedchequered cement concrete tiles 30cmx30cmx(22-25) mm thick, set jointed and pointed in neat cement slurry in floor with grey cement and pigment with 20 mm thick screed bed are bedding layer of cement mortar (1:4) for laying floor finishes complete all as specified and as directed. 80 M&L for machine cut kota stone slab flooring 18-20 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4, rubbing and polishing etc. complete all as specified and as directed. 81 M&L for machine cut kota stone 18-20 mm thick as in riser, steps, skirting, dado and pillar laid over cement screed andjointed with grey cement slurry mixed with pigment to match the shade of the slab including 15mm thich cement screed or bedding layer in cement mortar (1:4), rubbing and polishing etc. complete all as specified and as directed. 82 M&L for two coats of synthetic enamel paint on new/old concrete or plastered surfaces (as in kerb stones etc) over a coat of primer including preparation ofnew surface complete all as specified and as directed. 83 S & F 4.0 mm thick frosted sheet glass ordinary quality (in repair) and glazing with oil putty in square n.exceeding 0.5 Sqm in eachpane including hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads metal frame including punching or drilling out old glazing pins/spring clips and providing and fexing new complete all as specifed and as directed. 84 S & F 4.8 mm thick frosted sheet glass ordinary quality (in repair) and glazing with oil putty in square n.exceeding 0.5 Sqm in eachpane including hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads metal frame including punching or drilling out old glazing pins/spring clips and providing and fexing new complete all as specifed and as directed. 85 S&F in repair PVC Coated/ Stainless Steel AISI 304 curtain rods 1.6 mm thick, 25 mm dia of approved quality with decorative wooden finish or as per required colour and two number brackets as per approved quality and diesign (for each 01 mtr of rod) fixed in brick/concrete wall and same finished knobs on each end of curtain rodcomplete all as specified and as directed. 86 S & F rotational moulded polyethylene water storage tank white colour (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 300 litres including all accessories and dismantling of existing water tank complete all as specified and as directed. 87 S & F 3 layered heavy duty blow moulded Rotational moulded HDPE water storage tank 1000 ltr capacity white colour hoisted and fixed in position having 20mm dia PVC float valve and tank nipple, including dismantling of existing tank complete all as specified and as directed. 88 S&F in repairs HDPE PVC lid (cover) for 300 to 1000 Litres capacityPVC tanks,complete all as specified and as directed. 89 S&F in replacement PVC syphone Cylinderical type Push buttonfor low level flushing cistern complete all as specified and as directed. 90 S&F in repair PVC trap/floor trap with grating including jointing to wastepipe,dia of outlet 100mm in cement concrete type, B1, (1:2:4)complete all as specified and as directed. 91 Demolition of brick work or stone masonry built in cement mortar including all quoines arches,pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified. 92 M&L for old size Brick work with sub class B bricks, straight or curved on plan to exceeding 6 m mean radius in cement mortar 1:4 complete all as specified and as directed. 93 M&L for 15 mm thick rendering with redimix plaster (as per manufaturers instruction) on face of brick or concrete surfaces finished even and smooth surface without using extra cement complete all as specified and as directed.Note :- Contractor shall be bounded to carryout repair / maint upto G+4 storey building and the rate shall be deemed including scafolding / double scafolding, safety equipments and misc accessories. 94 M&L for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or by steel wire brushes, scraping down smoke spots, moulds, moss and elllorescent salts, trading oil, gresey spots etc, and applying one coat of cement base paint on wall complete all as specified and as directed. 95 M&L for applying two coats of cement base paint on walls after preparation of newly plastered surfaces complete all as specified and as directed. 96 S&F in repair70 mmthick factory made SFRC manhole cover of any size any shape (square/rectangular/circular)with frame set in cement mortar 1:4complete all as specified and as directed. 97 S&F in repair deco door seal bottom brush dust stopper strip aluminium plate with nylon brush for cover the bottom door gaps between 20-25mm including fixing with steel screws etc, complete all as specified and as directed.
