Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Providing and fixing of Wooden fire rated doors as per BS:476 Part- 20 and 22 and IS 3614 part-1 and part-2 for stability, integrity and thermal insulation. 03 Criteria Wooden door confirming to IS 277 with the following specification. Recommended fire door shall have doors tested at CBRI for maximum rating of 2hrs tested either withor without vision panel. Individual Test certificates should be available for glass used in vision lites confirming the required fire ratings.Any deviation in specification other than what is mentioned in the test certificates are not allowed. Proper label confirming the type of door and the hourly rating is mandatory. Approved manufacturer Navair International Ltd or equivalent subject to architect’s approval. And should be ISO Certified company.Door leaf shall be minimum 50mm thick fully flush door with or without vision lite. 50mm thick shutter, comprising of 75mm x 44mm hardwood internal timber frame work, with infill of 48 kg/m3, ceramic fiber blankets, coated with VIPER FR intumuscent coating on both sides for insulation. The coated insulation shall be sandwiched between maximum 12mm thick HILUX Make Calcium Silicate Boards on both sides (edge to edge on internal Hardwood frame) having a maximum density of 900 Kgs/ Cum, cladded with 3mm ply commercial ply on both faces. (The same can be pasted with1mm thick laminate (as per approved shade) or replaced with 4mm thick teak ply as per clients requirement at an extra cost) on both sides of the shutter, with 50mm x 10mm hard wood lipping all round the shutter. r. The rebate shall be of 20mm x 54mm in the Door Frame to accommodate the shutter . Both frame and shutter shall be fitted with intumescent Fire seal strips , The shutter fitted with 20x4mm Fire seal and Frame with 2 no. Fire seal of size 10x4mm on all the three sides of the except bottom. The pasting of the ply/veneer/laminate should be done using automatic machine and should be free from any nails or perforations. (Main Staircase Doors). Tata Parvez, Navair, Kutty Makewith the prior approval of engineer-in-charge. |
| 2 | Supply and fixing the door frame will be made out of Hardwood of maximum section 120 x 70mm and coated with VIPER Fire reatrdent Primer.(Main Hall Doors)Tata Parvez, Navair, Kutty Makewith the prior approval of engineer-in-charge. |
| 3 | Supply and fixing SS Ball Bearing Hinges of size 100 x 75 x 3mm complet with SS Screws of BB1953 e ( 4 Nos per panel ) (Required For All Doors).Hafele, Dorset, Hormann Makewith the prior approval of engineer-in-charge. |
| 4 | Supply and fixing Panic Bar single leaf panic bar. Becker, Dorma, Briton, Hormann Makewith the prior approval of engineer-in-charge |
| 5 | Supply and fixing PEL905 Becker F.S. Make Panic Trim For Operation From The Other Side Of The Panic Bar. Becker, Dorma, Briton, Hormannwith the prior approval of engineer-in-charge |
| 6 | Supply and fixing Mortise Dead Lock with 80mm cylinder body both side key DL7260 Becker F.S.Dead Lock Required For Shaft Door Location).Becker, Dorma, Briton, Hormann Makewith the prior approval of engineer-in-charge. |
| 7 | Supply and fixing SS D Type Pull Handle of size 300mm mm Long of PHD2230Becker, Hafele, Dorset, Hormann Makewith the prior approval of engineer-in-charge. |
| 8 | Supply and fixing Door closers of BLC-604 (Required For All Fire Doors Except Shaft Door).Becker, Dorma, Briton, Horman Makewith the prior approval of engineer-in-charge |
| 9 | Supply and fixing Stainless Steel 304 grade 300mm Long Tower Bolt ofwith necessary screws as required.Hafele, Dorset, Hormann Makewith the prior approval of engineer-in-charge. |
| 10 | Supply and fixing Anchor fastners of of maximum 120mm length. Make - HILTI, FISHER, Godrej makewith the prior approval of engineer-in-charge |
| 11 | Supply and fixingIS-1212 S88 UL 1784-01 Smoke tested adhesive seal Make Smoke seal batwing type on all side of frame. Make - LORIENT, Becker FS, PEMKOmake with the prior approval of engineer-in-charge. |
| 12 | Supply and fixing 5 MM thick clear Non wire 2 Hr Fire Vision glass 300x300mm. Saint gobain, Asahi India glass ltd., Modiguard make with the prior approval of engineer-in-charge |
| 13 | Providing and Fixing SS ball bearing hinge (4 x 3 x 3mm) - Isuzul, Godrej, Hettich make with prior approval of Engineer-in-Charge. |
| 14 | Providing and Fixing Tower bolt 12` Aluminium -Godrej, Ebco, Hafele make r prior approval of Engineer-in-Charge. ( |
| 15 | Providing and Fixing SS finish door stopper - Godrej/ Ebco/ Hafelemake with prior approval of Engineer-in-Charge. |
| 16 | Providing and Fixing SS back stopper- Godrej/ Ebco/ Hafelemake with prior approval of Engineer-in-Charge. |
| 17 | Providing and Fixing Pull handle 240 mm - Godrej/ Ebco/ Hafelemake with prior approval of Engineer-in-Charge. |
| 18 | Providing and Fixing Ebco SS 304 friction stay-FRS-16 - ModelofGodrej, Ebco, Hafelemake with prior approval of Engineer-in-Charge |
| 19 | Providing and Fixing Door Closer 60 kg Tto 90 kg of Ebco, Godrej, Dorset make with prior approval of Engineer-in-Charge. |
| 20 | Providing and Fixing Mortise lock and latch with both side handle and keyed cylinder. 5991 NEH-16, 200mm of Ebco, Godrej, Dorset make with prior approval of Engineer-in-Charge |
| 21 | Providing and Fixing Patch fittings with 90 kg Floor spring of Ebco, Godrej, Dorset make with prior approval of Engineer-in-Charge. |
| 22 | Providing and Fixing H Handle SS 304 , 750 mm hole to hole of Ebco, Godrej, Dorset make with prior approval of Engineer-in-Charge. |
| 23 | Providing and Fixing ALDROP 16*200mm stainless steal complete in all respect Ebco, Godrej, Dorset make with prior approval of Engineer-in-Charge |
| 24 | Supply and installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine laminated finish, groove perforated slats L8-2 - (2mm grooves @ 8mm centers) / L16-2 - (2mm Slats @16mm pitch) / L32-2 - (2mm grooves @ 32mm centers) / L64-2 - (2mm grooves @ 64mm centers) / L128-2 - (2mm grooves @128mm centers), backlined with Soundtexblack acoustical fleece, tongue-groove edge for a seamless look, FR Grade, size 128x2440x16mm, volume density of base board 800Kg/m3, weight 8Kgs/m2 (L16), 10.5Kgs/m2 (L32), 11Kgs/m2 (L64) installed by using Anutone Strut framework system.Anutone Strut framework system includes Anutone Strut CC50 aluminium core cross channel having thickness 0.55mm, length 3600mm, knurled web 40mm, depth 50mm and equal flanges 15mm is fastened to wall or framework behind vertically/horizontally at every 600mm c/c. Anutone Strut CC18 aluminium core cross channel, thickness 0.5mm, length 2400mm,web 15mm and 27mm, depth 18mm and flanges of 7mm with suitable edge andcentre brackets is then fixed perpendicular to the Strut CC50 Cross channel with the help of fasteners at every 400mm centers. Slats Surco of size 128x 2440x16mm in then fixed perpendicular to CC18 with suitable edge and centre brackets. Short edges of the panel are staggered.Contractor to provide expansion joints of 3mm at every 4.88m length wise and 4.992m width wise. Panels are backlined with Anutone SynthPF 10x25 held in position with dab spots of Anutone Stick S7 of Anutone, Knauf Daniel, Tranquill make with prior approval of Engineer-in-Charge.(FOR DINING CUM CONFRENCE HALL) |
| 25 | Supply and installation of Anutone Stretch Hush system consisting of FR Grade Hush fabric-based membrane with high-performance integrated core andacoustically-transparent face covering of choice colour, size 1.4mx75m, stretched by using combination of Anutone Strut C50 Cross Channel and Anutone Strut FS15/25 Tracks, Anutone Strand, 10mm woodenbase, Anutone SynthPF 10x10 infill with requisite accessories. The Anutone Strut system includes Anutone Strut CC50 Cross Channel, fully knurled, sectional thickness 0.55mm, length 3600mm, web 40, depth 50mm and equal flanges of 15mm is fastened to the wall @ 600mm centers. Woodenbase 10mm is then installed on the CC50 along the marking lines with metal fasteners at 300mm centers. FS15/25 tracks to be installed on wooden base, by first applying Stick S7 adhesive on both surfaces for a true and continuous secure grip, and heavy-duty fasteners at 150mm centers on one/both sides of Anutone Strut Tracks. Strand square edge magnesite bonded pinewood fiber panels of size 600x1200x20mm having density 400kg/m3, weight 8kg which is fixed to Strut CC50 Cross Channel inbetween tracks. Long edge of panels should be perpendicular to length of Strut CC50 Cross Channel. SynthPF 10x10mm adhered on Strand by using Stick 7 adhesive. The Anutone Stretch Hush acoustical membrane of width 1.4m is stretched and tucked into the Anutone Strut Tracks and secured to the locking jaws with purpose-specific tucking tools to obtain smooth, taut, wrinkle-free finish. Ensure the weft and weave of the fabric along with the surface are all oriented in one direction to achieve uniform shade. Note: Minimum 100mm additional fabric is required for tucking hence maximum module wall fabric width would be 1300mmof Anutone, Knauf Daniel, Armstrong, Tranquill make with prior approval of Engineer-in-Charge. (FOR DINING CUM CONFRENCE HALL) |
| 26 | Supply and Installation of Anutone Subtex Nubby,square edge, Glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having volume density 120Kgs/m3, weight 1.8kg/m2 which is suspended by using 0.3mm thick Anutone Skelet TrelisT15 metal grid system.Anutone Skelet TrelisT15 metal grid system of 600x600mm module includes Anutone Skelet WA15W30 wall angle with unequal flanges of 15/19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Anutone Skelet MT15W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Anutone Skelet MT15W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Anutone Skelet CT15W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally Anutone Skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600x600mm module. Anutone Subtex Nubby square edge of size 595x595x15mm shall be placed into the grid size of 600x600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The system is backlined with the acoustical infill Anutone SynthPF 10x25 of Anutone, Armstrong,Knauf Daniel, Tranquill make with prior approval of Engineer-in-Charge. (FOR CONFRENCE HALL) |
| 27 | roviding and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge.(The panel shuttering work shall be paid for separately).(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). (DSR-16.75)(FOR BASEMENT FLOORING) |
| 28 | Providing and fixing solid laminated flush door shutters having uniform thickness of 37mm with smooth finish and moisture content 10 to 12% with water absorption of 2%, climate stable, warp and bend free as certified by IS-2202 with 1mm HPL conforming to IS - 2046including , screws chocks/cleats and stops etc. (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position) of Greenlam, century, duro)with prior approval of Engineer-in-Charge |
| 29 | Providing and laying smooth stone texture paint in colors shade and texture as per approval applied by a coat applied by a spray gun in the desired shade of approved make including sand papering the existing surface of putty, to give it a base for applying primer coat. It also includes scaffolding charges complete in all respect (FOR EXTERIOR FACADE) (N.S.ITEM) of Heritage Paint, Spectrum, Asian make with prior approval of Engineer-in-Charge |
| 30 | Supplying and fixing 10mm thick multiwall polycarbonate sheet roof cladding at all levels as per pattern for skylight roof cladding and specials with necessary aluminium extrusions with EPDM gasket, cutting, fabricating, erection at all levels with paintings all fixtures and fixing accessories such s self drilling, self taping fastener including cost of all materials, tools, tackles, equipment, preparation of shop drawings etc. all complete as per specifications of Lexan, Polygal, Danaplon make with prior approval of Engineer-in-Charge. (FOR RAMP ROOFING). |
| 31 | Providing and Fixing of Panelling on wall with BWP grade Ply of 12mm on MS Frame work.25mmx50mm MS tube with composite panelling lined with 1mm thick Laminate panelled.Surface shall be inperfectplumb with wall andceiling.(Hall Wall Panelling) of Greenlam, Century , Archidmake with the prior approval of engineer-in-charge |
| 32 | Providing and Fixing of Panelling on wall with BWP grade Ply of 12mm on MS Frame work.25mmx50mm MS tube with composite panelling lined with 1mm thick Laminate panelled.Surface shall be inperfectplumb with wall andceiling.(Hall Wall Panelling) of Greenlam, Century , Archidmake with the prior approval of engineer-in-charge. |
| 33 | Extra for Proving V Groove and L groove in granite cladding including cutting of stone, Polishing to give high gloss finish complete in all respect with theengineer in charge. |
| 34 | Providing 15mm thick Engineered Wooden Flooring with plank width of 185mm / 135mm and length of 1800mm / 2100mm and top layer up to 3mm Oak natural Veneer. Surface of Top layer is prefinished with several layer of UV hardened acrylic lacquer. Strictly Free from Formaldehyde and solvents. Flooring plank shall be interlocked using Plank Loc locking system in a glue less floating manner. Engineered wood planks shall be a composition of 3 layer of Pine wood with direction of each layer oriented at right angle to the adjacent layer of natural strain in Lacquer and Non-Beveled /Beveled in length and width (FOR DINING CUM CONFRENCE HALL) (N.S.ITEM) of Mikasa, squarefoot, Span make with prior approval of Engineer-in-Charge. |
| 35 | Providing and laying fine flakes texture paint in colors shade and texture as per approval applied by a coat applied by a spray gun in the desired shade of approved make including sand papering the existing surface of putty, to give it a base for applying primer coat. It also includes scaffolding charges complete in all respectof Heritage Paint, Spectrum, Asian make with prior approval of Engineer-in-Charge. (FOR INTERIOR FACADE) |
| 36 | Providing and fixing Movable Partition consisting of series of individual flat elements of 100 mm thick travelling along the ceiling track assembled to form a solid wall. The entire system must function as a solid wall and even when closed should reveal minimal screws, fixing or other similar solid metal parts. The sound insulation of the operable partition 50dB tested under third party reputed laboratory in accordance to EN 20140-3. The test certificate should show the make and model of the system. Elements must be constructed of a torsion-free steel horizontal tube frame and torsion-stiff vertical aluminium profiles, bolted together to make the element strong and sturdy. The frame must be clad either side with 16mm MDF panels hung inacoustic free suspension from the panel frame. The panel skin shall be installed on site and able to be replaced without totally disassembling the panel frame. The element must be constructed in accordance with the specified sound insulation requirements. The elements must be inter-connected by means of a positive locking concave/convex aluminium profile with an integrated magnetic strip and sealing lip having a linear attraction of 40N/m. The spindle mechanism in every element should be connected to the top and bottom horizontal seals which should be constructed of aluminium plates with flexible rubber at the contact point. Specially formed polyurethane corner rubber seal to be provided for overlapping acoustic seals horizontal sealing strip.Each element of Variflex must have a spindle mechanism which should be connected to the spring loaded top and bottom retractable seal. The spindle mechanism should be operated manually by a bayonet connected crank handle that acts as a lock in function during cranking process. Drop down seal are not acceptable. The horizontal top and bottom seals must be retracted as per the operating mechanism and should ensure a contact pressure of 800N when the seals are completely extended. The spring loaded retractable horizontal seals should also be able to adjust to minor floor undulation for better accoustic efficiency. No fixed sweep seals allowed in top and bottom of the element that would rub against the track or floor while moving the element. The seal spindle mechanism must be accessible while the panel is hanging for servicing and adjustment if necessary. The fascia boards to be clipped on as free oscillating panels to offer optimum sound insulation.The fascia boards must be removable without dismantling the Movable walls elements. Sound Barrier Partition above Operable Sliding/Folding Partition. Providing and fixing to the required profile and shape 2 layers of 12.5mm thickGypsum board on GI framework comprising 40x40x18G galvanized tubular frame 610x610mm centre to centre fixed on Roof Structure with 40x40x5 MS cleat, 100mm long 1200 c/c and ceiling framework with welded connections. The Gypsum board to be backed with 50mm thick resin bonded fiberglass cut to size and inserted in GI framework and held in place with 28G x 12mm GI wire netting. The first layer of Gypsum board to have joints over frame and second layer of Gypsum board tohave joint staggered with respect to the first layer, all joints between board in both layers to be taped with paper tape and filled with sealing compound. Gypsum board layer to be sealed at junction with Roof sheeting / structure and false ceiling below with the non-hardening mastic compound, so as to provide smooth surface.Entire work to be done as per drawing of Dormahuppe, skyfold, modernfold make with the prior approval of engineer-in-charge.(FOR DINING CUM CONFRENCE HALL) |
| 37 | Supply and erection of GRC screens in approved designs and sizes and thickness manufactured containing alkali resistant Glass Fiber of make NEG, Japan and fixing by Dry Cladding using SS Cleats, SS Threading rods, Self Tapping Screws etc. Providing and fixing factory manufactured of G.R.C Jali made. It also includes scaffolding charges complete in all respect of Mahesh GRC, Unistone, Asian GRC make with the prior approval of engineer-in-charge. (FOR EXTERIOR FACADE). |
| 38 | Design, Fabrication, Supply, Installation, Testing and Commissioning of Electric Traction Type fully automatic gearless andsuitablefor Machine room, PassengerElevator having SS Enclosurewith AC Variable Voltage and Variable Frequency drive unit suitable for operation on 415Vplus /- 10% , 3 Phase, 50 Hz. AC supply,power operated SScenter bi-parting opening type car and landing doors (Landing Doors with minimum 2hours Fire rating), electro-magnetic brake system, car operating panel with braille push buttons, overload warning indicator, battery operated alarm bell, emergency light, intercom and SS Handrail to meet the requirement as per standard for physically challanged , infrared ray sensing door protection for full height, reverse phase relay on controller, fire man`s switch at ground floor, digital car positions indicator in car and at all floors with up / down direction indications, light fixtures, ventilation fan, Rear wall in 12mm Thk. Toughened Clear Glass Panel, landing sill, main beam in shaft for machine, pit ladder,complete with all accessories serving different floors in the lift shaftalongwith Integrated controller in door frame, Predictive maintenance Enabledcompletecomplyingwithrelevant IS codes and requirement of local authorities, getting approval of concerned state/ central government authorities including 12 months guarantee with free maintenance and replacements of equipment and spares. Automatic rescue device complete with dry maintenance free Ni-Cd batteries with charging circuit as required.Elevator control and Interfacing with building fire alarm System Voice announcement system in the car to announce the position of the elevator in the hoistway as the car passes or stops at a floor served by the elevator.Passenger LiftL1 and L2 i) No of persons - 10 Paxii) Capacity- 680 Kgiii) Stops and Openings ( Same side)- 8 Nos.iv) Aproximate Travel- 25 metersv) Travel Speed- 1.5 mpsvi) Car and Hoistway Entrnce -800x2100viii) Type of Operation- Group Supervisory Controlix) Layout- Both lifts adjacent to Each OtherPASSENGERELEVATOR AS DESCRIBED ABOVE of JOHNSON / KONE / OTISmake with prior approval of Engineer-in-Charge. |
| 39 | Providing and fixing in position Bib cock with wall flange (model CQT-23047) Jaquar, Hindware, Parryware make with prior approval of Engineer in charge. |
| 40 | Providing and fixing Hand shower (Health faucet) with 1.0m long easy flex tube in chrome finish and wall hook (model no. ALD-565)Jaquar, Hindware, Parryware make with prior approval of Engineer in charge |
| 41 | Providing and fixing in position two way Bib cock for and hand shower (model CON-041KN) Jaquar, Hindware, Parryware make with prior approval of Engineer in charge. |
| 42 | Providing and fixing in position Angle Valve(model No.CON-059KN)ofJaquar, Hindware, Parryware make with prior approval of Engineer in charge |
| 43 | Providing and fixing in position Central hole basin mixer without popup waste system with 450mm having long braided hoses (model (CON-169KNB) of Jaquar, Hindware, Parryware make with prior approval of Engineer in charge. |
| 44 | Providing and fixing in position 15 mm i/d wall mounted sink cock with swinging casted round shape spout (Model No.CON-347KN)of Jaquar, Hindware, Parryware make with prior approval of Engineer in charge. |
| 45 | Providing and fixing in position European Type Wall Mounted Water Closet (white) Suit of size(mm), (Model No. CNS-WHT-363SPPZ) of Jaquar, Hindware, Parryware make with prior approval of Engineer in charge. |
| 46 | Providing and fixing under counter Basin (model No. CNS-WHT-705) of Jaquar, Hindware, Parryware make with prior approval of Engineer in charge |
| 47 | Providing and fixingfloor drain (B)with jali as per I.S:14735:1999 marked of Supreme, Astral and Prakash make with prior approval of Engineer in charge. |
| 48 | Providing and fixing in position Geyser of 25 liters capacity (Model-Elena Vertical Manual) ofJaquar, Hindware, Parryware make with prior approval of Engineer in charge. |
| 49 | Providing and fixing in position Bottle trap (model no.ALD-769L300x190) with internal partition 32mm size with 300mm and 190mm Long wall connections pipes and wall flange and waste coupling. (Model no.ALD-705L130) 32mm size full thread with 130mm Height of Jaquar, Hindware, Parryware make with prior approval of Engineer in charge. |
| 50 | Providing and fixing Pillar Cock long neck with 450mm long braided Hose (model No. CQT -23021) of Jaquar, Hindware, Parryware make with prior approval of Engineer in charge |
| 51 | Providing and fixing Wall Hung Basin (model No. CNS-WHT-801 plus CNS-WHT-301) with full pedestalofJaquar, Hindware, Parryware make with prior approval of Engineer in charge |
| 52 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 110mm dia including fixing jointing and testing etc. Supreme, Astral and Prakash make with prior approval of Engineer in charge.FLOOR TRAP WITH TOP TILE and STAINER(100mm) |
| 53 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 110mm dia including fixing jointing and testing etc. Supreme, Astral and Prakash make with prior approval of Engineer in chargeFLOOR TRAP WITH TOP TILE and STAINER(125mm) |
| 54 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 110mm dia including fixing jointing and testing etc. Supreme, Astral and Prakash make with prior approval of Engineer in chargeDOOR TEE |
| 55 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 110mm dia including fixing jointing and testing etc. Supreme, Astral and Prakash make with prior approval of Engineer in chargeDOOR BEND (TS) |
| 56 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 110mm dia including fixing jointing and testing etc. Supreme, Astral and Prakash make with prior approval of Engineer in chargeBEND 87.5 ° |
| 57 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 110mm dia including fixing jointing and testing etc. Supreme, Astral and Prakash make with prior approval of Engineer in chargeDOOR CROSS TEE |
| 58 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 110mm dia including fixing jointing and testing etc. Supreme, Astral and Prakash make with prior approval of Engineer in chargeCoupler |
| 59 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 110mm dia including fixing jointing and testing etc. Supreme, Astral and Prakash make with prior approval of Engineer in chargeDoor Cap |
| 60 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 110mm dia including fixing jointing and testing etc. Supreme, Astral and Prakash make with prior approval of Engineer in chargeVENT COWL WITH PREMIUM WIREMESH |
| 61 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 110mm dia including fixing jointing and testing etc. Supreme, Astral and Prakash make with prior approval of Engineer in chargeMulti floor trap |
| 62 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 110mm dia including fixing jointing and testing etc. Supreme, Astral and Prakash make with prior approval of Engineer in chargeCleanout |
| 63 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 160mm dia including fixing jointing and testing etc.Supreme, Astral and Prakash make with prior approval of Engineer in chargeDoor tee |
| 64 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 160mm dia including fixing jointing and testing etc.Supreme, Astral and Prakash make with prior approval of Engineer in chargeCoupler ( Rib Type) |
| 65 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 160mm dia including fixing jointing and testing etc.Supreme, Astral and Prakash make with prior approval of Engineer in chargeVent cowl |
| 66 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 160mm dia including fixing jointing and testing etc.Supreme, Astral and Prakash make with prior approval of Engineer in chargeDoor Elbow |
| 67 | Providing and Fixing SWR Fittings (supreme make) for type B pipes 160mm dia including fixing jointing and testing etc.Supreme, Astral and Prakash make with prior approval of Engineer in chargeCleanout |
| 68 | Providing and Fixing dwc Fittings for double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 including fixing jointing and testing etc. for 150mm Pipe. Supreme, Astral and Prakash make with prior approval of Engineer in charge. ROTO DWC BEND 90D |
| 69 | Providing and Fixing dwc Fittings for double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 including fixing jointing and testing etc. for 150mm Pipe. Supreme, Astral and Prakash make with prior approval of Engineer in charge.ROTO DWC BEND 45D |
| 70 | Providing and Fixing dwc Fittings for double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 including fixing jointing and testing etc. for 150mm Pipe. Supreme, Astral and Prakash make with prior approval of Engineer in charge.ROTO EQUAL TEE |
| 71 | Providing and Fixing dwc Fittings for double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 including fixing jointing and testing etc. for 150mm Pipe. Supreme, Astral and Prakash make with prior approval of Engineer in chargeROTO CROSS TEE |
| 72 | Providing and Fixing dwc Fittings for double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 including fixing jointing and testing etc. for 180mm Pipe. Supreme, Astral and Prakash make with prior approval of Engineer in chargeROTO DWC BEND 90D |
| 73 | Providing and Fixing dwc Fittings for double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 including fixing jointing and testing etc. for 180mm Pipe. Supreme, Astral and Prakash make with prior approval of Engineer in chargeROTO DWC BEND 45D |
| 74 | Providing and Fixing dwc Fittings for double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 including fixing jointing and testing etc. for 180mm Pipe. Supreme, Astral and Prakash make with prior approval of Engineer in chargeROTO EQUAL TEE |
| 75 | Ground Floor Meter Board panel (N.S. ITEM)Incoming 1 Set of100 Amps. 415 Volts, FP MCCB of 25 KA with overload, O/C, S/C and earth fault protection.Bus bars 1 Set of 125-Amps, 3-Phase, 4-wire, 415 volts, 50 Hz Aluminium bus-bars with colour coded PVC heat shrinkable sleeves (Neutral to be equal to phase size).Metering and Indication One set of R/Y/B phase indication Lamp and MCB. 1 No. Multi Function Meters(A/V/kW/kWh) ON/OFF/TRIP indication lamp for incomer Outgoing 4 Nos. 63 Amps. FP MCB of 16 KA with energy meter2 Nos. 63 Amps. FP MCB of 16 KA Panel as mentioned aboveshould be complete in all respect with internal wiring, al. bus bar etc |
| 76 | 1st Floor Meter Board Panel (Typical for 1st, 2nd, 3rd, 4th and 5th Floor)Incoming 1 Set of160 Amps. 415 Volts, FP MCCB of 25 KA with overload, O/C, S/C and earth fault protection.Bus bars 1 Set of 200-Amps, 3-Phase, 4-wire, 415 volts, 50 Hz Aluminium bus-bars with colour coded PVC heat shrinkable sleeves (Neutral to be equal to phase size).Metering and Indication One set of R/Y/B phase indication Lamp and MCB. 1 No. Multi Function Meters(A/V/kW/kWh) ON/OFF/TRIP indication lamp for incomerOutgoing 4 Nos. 63 Amps. TPN MCB of 10 KA with energy meter2 Nos. 63 Amps. TPN MCB of 10 KA Panel as mentioned aboveshould be complete in all respect with internal wiring, al. bus bar etc. INNOVIC, ZENIA, ADLEC make with prior approval of Engineer in charge |
| 77 | SixthFloor Meter Board Panel (N.S. ITEM)Incoming 1 Set of160 Amps. 415 Volts, FP MCCB of 25 KA with overload, O/C, S/C and earth fault protection. Bus bars 1 Set of 200-Amps, 3-Phase, 4-wire, 415 volts, 50 Hz Aluminium bus-bars with colour coded PVC heat shrinkable sleeves (Neutral to be equal to phase size).Metering and Indication One set of R/Y/B phase indication Lamp and MCB. 1 No. Multi Function Meters(A/V/kW/kWh) ON/OFF/TRIP indication lamp for incomer Outgoing 4 Nos. 63 Amps. TPN MCB of 10 KA with energy meter1 Nos. 40 Amps. TPN MCB of 10 KA2 Nos. 63 Amps. TPN MCB of 10 KA Panel as mentioned aboveshould be complete in all respect with internal wiring, al. bus bar etc INNOVIC, ZENIA, ADLEC make with prior approval of Engineer in charge. |
| 78 | UPS Output DB (N.S. ITEM)Incoming 1 Set of40 Amps.DP MCB 1 Set of40 Amps.DP RCCB 30mABus bars 1 Set of 60-Amps, SPN Copper Bus BarOutgoing 6 Nos. 25 Amps. SPN MCB of 10 KA UPS Output DB as mentioned aboveshould be complete in all respect with internal wiring, al. bus bar etcINNOVIC, ZENIA, ADLEC make with prior approval of Engineer in charge |
| 79 | External lighting DB (N.S. ITEM) Incoming 1Set of40 Amps.FP MCB1 Set of40 Amps.FP RCCB 30mA1 No Astronomical timer with ContactorBus bars 1 Set of 60-Amps, SPN Copper Bus BarOutgoing 2 Nos. 10 Amps. SPN MCB of 10 KA2 Nos. 16 Amps. SPN MCB of 10 KA1 No FP Contactor with Astronomical timer8 Nos. 10 Amps. SPN MCB of 10 KA. Note- Power to these MCB shall be feed through above mentioned FP contactor and astro timer. Ext DBas mentioned aboveshould be complete in all respect with internal wiring, al. bus bar etc. INNOVIC, ZENIA, ADLEC make with prior approval of Engineer in charge. |
| 80 | Lift Machine Panel (N.S. ITEM) Incoming 1 No. 100 Amps 4 Pole on load auto change over system complete with 2 Nos. 100 Amp. 4P Contactor with voltage sensing realy interconnection etc. as required. 1 Set of100 Amps. 415 Volts, FP MCCB of 25 KA with overload, O/C, S/C and earth fault protection.Bus bars 1 Set of 125-Amps, 3-Phase, 4-wire, 415 volts, 50 Hz Aluminium bus-bars with colour coded PVC heat shrinkable sleeves (Neutral to be equal to phase size).Metering and Indication One set of R/Y/B phase indication Lamp and MCB. 1 No. Multi Function Meters(A/V/kW/kWh)ON/OFF/TRIP indication lamp for incomer Outgoing 3 Nos. 63 Amps. TPN RCCB of 30 mA3 Nos. 40 Amps. TPN MCB of 16 KA2 Nos. 40 Amps. DP MCB of 16 KA Panel as mentioned aboveshould be complete in all respect with internal wiring, al. bus bar etc.INNOVIC, ZENIA, ADLEC make with prior approval of Engineer in charge. |
| 81 | Supply, installation, testing and commissioning of 34 to 36 watt 2 ft X 2 ft (nominal size) recessed mounted LED Panel Light, in CRCA powder coated metallic housing, having lumen out put minimum 120 lumen/watt, suitable for recessed mounting,Armstrong/grid/POP/GB ceiling complete with Toatl system lumen )4400 lumenTHD (10%, PF )0.95. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. complete with all accessories, electronic driver, diffuser, directly on ceiling/ wall, including connections and earthing etc. as required. The seller shall provide five years manufacturers’ warranty for complete luminaire Havells, Philips, Wipromake with prior approval of Engineer in charge. |
| 82 | Supply, installation, testing and commissioning of 600 mm (nominal size) 9 to 10 watt Mirror light LED batten luminaire in aluminium housing with minimum light output 100 lumen/watt complete with all accessories, electronic driver, diffuser, directly on ceiling/ wall, including connections etc. as required of Havells, Philips, Wipromake with prior approval of Engineer in charge. |
| 83 | Supplying of 10 to 12 W downlighter Recess mounted complete with aluminium powder coated pressure die cast housing and PC diffuser, LEDs and electronic driver with THD (less-than 10%), Output Short Circuit Protection, Surge Voltage Protection. Minimum system efficacy of 100 lumen/Watt, Operating voltage range 140 V-270 V , The fixture shall be designed for a average LED life L70B50 50000 hours. LM 79 and LM 80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. The seller shall provide five years manufacturers warranty for complete luminaire of Havells, Philips, Wipromake with prior approval of Engineer in charge. |
| 84 | Supplying, installation, testing and commissioning of 12 to 15 W downlighter Recess mounted complete with aluminium powder coated pressure die cast housing and PC diffuser, LEDs and electronic driver with THD (less-than 10%), Output Short Circuit Protection, Surge Voltage Protection. Minimum system efficacy of 100 lumen/Watt, Operating voltage range 140 V-270 V , The fixture shall be designed for a average LED life L70B50 50000 hours. LM 79 and LM 80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. The seller shall provide five years manufacturers warranty for complete luminaireof Havells, Philips, Wipromake with prior approval of Engineer in charge |
| 85 | Supplying, installation, testing and commissioning of 10 to 12 W downlighter Surface mounted complete with aluminium powder coated pressure die cast housing and PC diffuser, LEDs and electronic driver with THD (less-than 10%), Output Short Circuit Protection, Surge Voltage Protection. Minimum system efficacy of 100 lumen/Watt, Operating voltage range 140 V-270 V , The fixture shall be designed for a average LED life L70B50 50000 hours. LM 79 and LM 80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. The seller shall provide five years manufacturers warranty for complete luminaire of Havells, Philips, Wipromake with prior approval of Engineer in charge |
| 86 | Supply, installation, testing and commissioning of 9 to 10 watt LED bulkhead fittings with IP 65 ingress protection aluminium housing with minimum light output 100 lumen/watt and Toatl system lumen )1000 lumenTHD (15%, PF )0.95. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. complete with all accessories, electronic driver, diffuser, directly on ceiling/ wall, including connections and earthing etc. as required. The seller shall provide five years manufacturers’ warranty for complete luminaireof Havells, Philips, Wipromake with prior approval of Engineer in charge |
| 87 | Supply, installation, testing and commissioning of 1180 mm (nominal size), 36 to 40 watt LED batten luminaire in aluminium housing with minimum light output 120 lumen/watt and Toatl system lumen )4000 lumen THD (10%, PF )0.95. The fixture shall be designed for a system life of 50,000 hours @ 70%lumen maintenance. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. complete with all accessories, electronic driver, diffuser, directly on ceiling/ wall, including connections and earthing etc. as required. The seller shall provide five years manufacturers’ warranty for complete luminaire of Havells, Philips, Wipromake with prior approval of Engineer in charge |
| 88 | Supplying of 12 to 15 W downlighter Surface mounted complete with aluminium powder coated pressure die cast housing and PC diffuser, LEDs and electronic driver with THD (less-than 10%), Output Short Circuit rotection, Surge Voltage Protection. Minimum system efficacy of 100 lumen/Watt, Operating voltage range 140 V-270 V , The fixture shall be designed for a average LED life L70B50 50000 hours. LM 79 and LM 80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. The seller shall provide five years manufacturers warranty for completeof Havells, Philips, Wipromake with prior approval of Engineer in charge. |
| 89 | upplying of 12 to 15 W downlighter Surface mounted complete with aluminium powder coated pressure die cast housing and PC diffuser, LEDs and electronic driver with THD (less-than 10%), Output Short Circuit rotection, Surge Voltage Protection. Minimum system efficacy of 100 lumen/Watt, Operating voltage range 140 V-270 V , The fixture shall be designed for a average LED life L70B50 50000 hours. LM 79 and LM 80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. The seller shall provide five years manufacturers warranty for complete luminaire of Havells, Philips, Wipromake with prior approval of Engineer in charge.( |
| 90 | Supply, installation, testing and commissioning of 1180 mm (nominal size), 36 watt - 40 watt LED batten luminaire in aluminium housing with minimum light output 120 lumen/watt and Toatl system lumen )4000 lumen THD (10%, PF )0.95. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. complete with all accessories, electronic driver, diffuser, directly on ceiling/ wall, including connections and earthing etc. as required. The seller shall provide five years manufacturers’ warranty for complete luminaire of Havells, Philips, Wipromake with prior approval of Engineer in charge. |
| 91 | Supply, installation, testing and commissioning of 9 to 10 watt LED Bracket light with 9W LED Bulb and accessories, electronic driver, diffuser, directly on ceiling/ wall, including connections and earthing etc. as required. The seller shall provide five years manufacturers’ warranty for complete luminaire of Havells, Philips, Wipromake with prior approval of Engineer in charge. |
| 92 | Supplying of 15 to 18Watt downlighter Surface mounted complete with aluminium powder coated pressure die cast housing and PC diffuser, LEDs and electronic driver with THD (less-than 10%), Output Short Circuit rotection, Surge Voltage Protection. Minimum system efficacy of 100 lumen/Watt, Operating voltage range 140 V-270 V , The fixture shall be designed for a average LED life L70B50 50000 hours. LM 79 and LM 80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. The seller shall provide five years manufacturers warranty for completeof Havells, Philips, Wipromake with prior approval of Engineer in charge. |
| 93 | Supply of 45 watt LED based street light luminaires, IP 65, with Die-cast aluminum electronic LED driver, High efficiency polycarbonate UV stablized cover, the fixture should have a minimum system efficacy of 100 lumen/watt and mechanical impact resistance rating of lk)=07. The fixture driver should have an operating voltage range of 140- 270 Volt, surge protection of )=10KV, PF))0.90, THD (10%. The fixture shall be designed for a system life of 50,000 hours. LM 79 and LM 80 reports need to be submitted from a NABL/ULaccredited lab to verify above parameters . The seller shallprovide five years manufacturers’ warranty for complete luminaire of Havells, Philips, Wipromake with prior approval of Engineer in charge |
| 94 | Supplying of 10 Watt, 0.5 Metre, LED Bollard Light fittings alongwith its all accessories like electronic LED driver made out of Die Cast base and opal acrylic diffuser having IP-65 protection and mechanical impact resistance rating of lk)=07. The fixture should have a minimum system efficacy of )95 lumen/Watt.The fixture driver should have an operating voltage range of 140-270 Volt, surge protection of PF))0.95, THD (20%. The fixture shall be designed for a system life of 50,000 hours. LM 79 and LM 80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. The seller shall provide five years manufacturers’ warranty for complete luminaire of Havells, Philips, Wipromake with prior approval of Engineer in charge |
| 95 | Supply, Installation, Testing and Commissioning of Exhaust fans/ wall fan/Ceiling Fans of following sizes including making the holes to suit the size of the fan and making good the damages, including providing and fixing of louvers/shutters, connection, testing and commissioning Supply, installation, Testing and Commissioning of 1200 MM 1200 MM ceiling fan with all accessories of Havells, Crompton, Ushamake with prior approval of Engineer in charge.( |
| 96 | Supply, Installation, Testing and Commissioning of Exhaust fans/ wall fan/Ceiling Fans of following sizes including making the holes to suit the size of the fan and making good the damages, including providing and fixing of louvers/shutters, connection, testing and commissioning Supply, installation, Testing and Commissioning of 1400 MM energy effceiant 1200 MM ceiling fan with all accessories of Havells, Crompton, Ushamake with prior approval of Engineer in charge.(N.S. ITEM) Usha |
| 97 | Supply, Installation, Testing and Commissioning of Exhaust fans/ wall fan/Ceiling Fans of following sizes including making the holes to suit the size of the fan and making good the damages, including providing and fixing of louvers/shutters, connection, testing and commissioning Supply, installation, Testing and Commissioning of450 MM, 900 RPM exhaust Fan with all accessories.Havells Turboforce 450 MM Havey duty Exhaust fan with Louver suitable for operation on 1-Phase.Or eqv Crompton, Almonard, Usha. |
| 98 | Supply, unloading, installation, testing and commissioning of 10KVA IGBT based ON line UPS (in-put3-Phase and out-put 1-Phase) with external extra Sealed maintenance free Batteries for 30 min. backup with the following with all required assecories and Masonary works. Operating Environment 0 - 35 Deg C, operating relative Humidity 20 - 80%, operating Elevation0 to 99.9 meters, Storage Temperature- 10 - 40Deg C, storage Elevation0 - 9000 meters, Regulatory Approvals CE,ISO 14001/ 9001. (Conf. N plus 1). ETN, NUMERIC and DELTA make with prior approval of Engineer in charge. |
| 99 | Supply, unloading, installation, testing and commissioning of Micro processor based. Intelligent Addressable 2 Loop Main Fire alarm panel, Central Processing Unit , with each loop capacity of 120 detector per loop with total of 240 detectors and devices with loop length up to 2 kmtr, network communication card, minimum 320 character graphics, LCD display with touch screen or other keypad and 1000 event history logs in the non volatile memory (EEPROM) power supply unit at 230 plus5 % V, 48 Hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout logs and facility to have integration with analog voice evacuation system( which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel should be compatible for integration with IBMS system with open protocol Bacnet/IP , complete as per specs and as required for following loops. NOTIFIER, SIEMENS and SYSTEM CENSOR MORLAY make with prior approval of Engineer in charge. |
| 100 | Supplying, of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.NOTIFIER, SIEMENS and SYSTEM CENSOR MORLAY make with prior approval of Engineer in charge. |
| 101 | SITC of Intelligent Addressable Multi-Sensor (Optical Smoke plus Heat) detector with base. The optical sensor element shall have multiple selectable sensitivity levels from 0.2% Obs/ft to 3.7% Obs/ft. The ROR detection element shall have selectable rate of rise setting of 8°C per minute and 11°C per minute (or close to this value not deviating more than 1°C). Fixed temp detection element shall have two selectable settings of 57°C and 68°C (or closer to this value not deviating by 1°C). Multis-sensor detector shall have a configuration mode that gives separate alarms for smoke detection and heat detection and shall indicate the cause of alarm (smoke or heat). Also the multi-sensor shall have combined configuration mode of smoke and heat detection that gives only one evaluated alarm from a multi-sensor detector in case of a fire event. The detector shall have operating temperature range from -9°C to 50°C and humidity tolerance range up to 95% RH, Non-Condensing.NOTIFIER, SIEMENS and SYSTEM CENSOR MORLAY make with prior approval of Engineer in charge. |
| 102 | SITC of Intelligent Addressable Multi-Sensor (Optical Smoke) detector with base. The optical sensor element shall have multiple selectable sensitivity levels from 0.2% Obs/ft to 3.7% Obs/ft. The ROR detection element shall have selectable rate of rise setting of 8°C per minute and 11°C per minute (or close to this value not deviating more than 1°C). Fixed temp detection element shall have two selectable settings of 57°C and 68°C (or closer to this value not deviating by 1°C). Multis-sensor detector shall have a configuration mode that gives separate alarms for smoke detection and heat detection and shall indicate the cause of alarm (smoke or heat). Also the multi-sensor shall have combined configuration mode of smoke and heat detection that gives only one evaluated alarm from a multi-sensor detector in case of a fire event. The detector shall have operating temperature range from -9°C to 50°C and humidity tolerance range up to 95% RH, Non-Condensing. (Above False Ceiling).. NOTIFIER, SIEMENS and SYSTEM CENSOR MORLAY make with prior approval of Engineer in charge. |
| 103 | SITC of Intelligent Addressable Multi-Sensor (Optical Smoke) detector with base. The optical sensor element shall have multiple selectable sensitivity levels from 0.2% Obs/ft to 3.7% Obs/ft. The ROR detection element shall have selectable rate of rise setting of 8°C per minute and 11°C per minute (or close to this value not deviating more than 1°C). Fixed temp detection element shall have two selectable settings of 57°C and 68°C (or closer to this value not deviating by 1°C). Multis-sensor detector shall have a configuration mode that gives separate alarms for smoke detection and heat detection and shall indicate the cause of alarm (smoke or heat). Also the multi-sensor shall have combined configuration mode of smoke and heat detection that gives only one evaluated alarm from a multi-sensor detector in case of a fire event. The detector shall have operating temperature range from -9°C to 50°C and humidity tolerance range up to 95% RH, Non-Condensing. (Below False Ceiling).. NOTIFIER, SIEMENS and SYSTEM CENSOR MORLAY make with prior approval of Engineer in charge. |
| 104 | SITC ofResponse Indicators with Single LED.. NOTIFIER, SIEMENS and SYSTEM CENSOR MORLAY make with prior approval of Engineer in charge. |
| 105 | SITC of Intelligent AddressableManual Pull Stations / Manual Call Points suitable for wall/column mounting. MCP shall have red coloured housing with molded, raised-letter operating instructions of contrast colour. The MCP shall latch mechanically upon operation and shall remain so until manually reset with its key by an authorized operator. The MCP shall have operating temperature range from 0°C to 50°C and humidity tolerance range up to 93% RH, Non-Condensing.. NOTIFIER, SIEMENS and SYSTEM CENSOR MORLAY make with prior approval of Engineer in charge. |
| 106 | SITC of Intelligent Addressable, Supervised Short-Circuit Isolator. The Isolator Monitor Module shall have operating temperature range from 0°C to 49°C and a humidity tolerance of up to 90% RH, Non-Condensing. . NOTIFIER, SIEMENS and SYSTEM CENSOR MORLAY make with prior approval of Engineer in charge. |
| 107 | SITC of Addressable Notification Devices (Hooter with Strobe). Hooter with Strobe unit shall sit directly on addressable NAC (Notification Appliance Circuit) of FACP, fully supervised and powered from FACP. Hooter and Strobe elements of the combined unitshall have independent activation and deactivation criteria. Hooter shall stop at alarm `Acknowledge` and the Strobe shall stop at panel `Reset`. The Hooter and Strobe element of Hooter cum Strobe combined unit shall be selected and triggered independently from FACP for performance check and maintenance. Hooter with Strobe unit shall have provision to be tested by a hand-held field diagnostic tool in `Silent Mode` and `Full Operation Sound Mode`. The Strobe shall have multiple selectable candela settings configured and selected from the FACP. The hooter cum Strobe unit shall deliver output up to 94 db. at 3m from its installed location. The sounder/strobe unit shall display the voltage received by them at the control panel. The activation and deactivation requirement of Notification devices shall not be deviated. No external 3rd party power supply shall be permitted.. NOTIFIER, SIEMENS and SYSTEM CENSOR MORLAY make with prior approval of Engineer in charge. |
| 108 | Supply,installation, testingandcommissioningof 5A power supply which operates on 220 V 50 Hz power supply with 24 V DC supply with built in battery and battery charges for 2 hours backup. Power supply is for powering hooters/strobes.. NOTIFIER, SIEMENS and SYSTEM CENSOR MORLAY make with prior approval of Engineer in charge. |
| 109 | SITC of Intelligent Addressable, Supervised Monitor Module monitoring Potential-free, Normally Open Dry Contact input. The Monitor Module shall have operating temperature range from 0°C to 70°C and a humidity tolerance of up to 93% RH, Non-Condensing. NOTIFIER, SIEMENS and SYSTEM CENSOR MORLAY make with prior approval of Engineer in charge. |
| 110 | SITC of Intelligent Addressable Potential-free, Form-C, SPDT contact based control module to trigger 3rd party utilities like Pressurization fan activation, Special notification activation etc. The contact shall be rated for 2A@24Vdc (Resistive) and 1A@24Vdc (Inductive). The control module shall have operating temperature range from 0°C to 49°C and a humidity tolerance of up to 93% RH, Non-Condensing. NOTIFIER, SIEMENS and SYSTEM CENSOR MORLAY make with prior approval of Engineer in charge. |
| 111 | SITC ofFireman Jack . CRAB TREE, HONEYWELL and SYSTEM CENSORmake with prior approval of Engineer in charge. |
| 112 | Supply and laying of 2 core 1.5 Sq mm stranded plain annealed copper conductor glass mica taped , XLPE insulated , LSZH inner sheathed , galvanised steel wire armoured and over all LSZHout sheatheated fire survival cable generally as per BS:7846:2009 including connections etc as required . The cable will be fixed on surface with suitable saddles at an interval of not more than one meter. POLYCAB, KEI, HAVELLS make with prior approval of Engineer in charge |
| 113 | Supply, installation, testing and commissioning offixed type IR indoor Dome type, 1/3` 4 MP ,progressive scan dual Streaming: H.265 smart codec, dual stream support, 2688 x 1520 resolution, Auto lens detection (2.7-13.5 mm) ,compatible with digital video recorder, PoE (802.3af) or 12 VDC support,UL/CE Listed,ONVIF conformant with IP 66 weather proof housing and 30 mtrs IR range. HONEYWELL, HIKVISION, PANASONIC make with prior approval of Engineer in charge |
| 114 | SITC of 16 channel network recorder with 320 Mbps incoming bandwidth , Builtin POE switch,8 SATA ports up to 64 TB with RAIDS 0/1/5/6/10 configuration, Two Monitor HDMI Out . four USB ports. Operating temperatureplus 0°C toplus 50°C , Operating humidity (90% non-condensing.HONEYWELL, HIKVISION, PANASONIC make with prior approval of Engineer in charge |
| 115 | SITC of 32 channel network recorder with 320 Mbps incoming bandwidth , Builtin POE switch,8 SATA ports up to 64 TB with RAIDS 0/1/5/6/10 configuration, Two Monitor HDMI Out . four USB ports. Operating temperatureplus 0°C toplus 50°C , Operating humidity (90% non-condensing.HONEYWELL, HIKVISION, PANASONIC make with prior approval of Engineer in charge |
| 116 | SITC of of 8TB Survillance Hard Disk of approved makeSEGATE/WB/SAMSUNG make with prior approval of Engineer in charge |
| 117 | Supply , Installation , Testing and Commissioning of 24 port L2 web Managed switch having port density 16 Nos. of 10M/100M/1G RJ45 Port POE/POE plus ports , 2 Nos. of 1G/10G SFP Ports , 1Xconsole port , Available POE power 370 W , 128 Gbps switching bandwidth , 16K MAC address support . DLINK/CISCO/HP make with prior approval of Engineer in charge |
| 118 | Supply , Installation , Testing and commissioningof 18 U floor mount rack with fans , 2 cable managers , stationary shelf , 2 Nos of hardware pkts .DATA RACK / OMNITECH /RITTAL make with prior approval of Engineer in charge |
| 119 | Supplying and laying of UTP 4 pair CAT 6 LAN Cable in surface/ recessed PVC conduit as required. 4 Pair CAT6 Unshielded, Twisted Pair (U/UTP) Cable. Blue in colour conforming to the following standards like ANSI/TIA 568 C.2, EN50173, IEC 11801 2nd ED, 700Mhz etc. in Cat 6 U/UTP LCS2 cable with 23AWG . Cost PVC pipe shall be included in the quoted price DLINK/LEGRAND/MOLEX make with prior approval of Engineer in charge. |
| 120 | Supply , Installation , Testing and Commissioning of Full HD 32` LED Professional Display Panel.SONY/LG/SAMSUNG make with prior approval of Engineer in charge |
| 121 | Supply installation and testing and commissioningof follwing size of Telephone distribution board in a M.S.boxwithhingedcover/doorcompletewithkronetypetagblockwithdoublejumperingfacility mounted on a bakelite sheet etc. including terminations of cable as required.KRONE, PANASONIC and IDLIS make with prior approval of Engineer in charge.10 Pair telephone distribution board |
| 122 | Supply installation and testing and commissioningof follwing size of Telephone distribution board in a M.S.boxwithhingedcover/doorcompletewithkronetypetagblockwithdoublejumperingfacility mounted on a bakelite sheet etc. including terminations of cable as required.KRONE, PANASONIC and IDLIS make with prior approval of Engineer in charge.50 Pair telephone distribution board |
| 123 | Supplyingandlaying offollowingpair0.5mmdiaFRLSPVCinsulatedannealedcopperconductor, armored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. (N.S. ITEM) kei, delton, havells make with prior approval of Engineer in charge10pairs |
| 124 | Supplyingandlaying offollowingpair0.5mmdiaFRLSPVCinsulatedannealedcopperconductor, armored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. (N.S. ITEM) kei, delton, havells make with prior approval of Engineer in charge50 Pair telephone distribution board |
| 125 | Supply of First aid box as approved by St. John Ambulance Brigade/Indian Red Cross make with prior approval of Engineer in charge |
| 126 | Supply and Installation of Shock treatment chartin Hindi and English duly mounted on a wooden frame with glass Jyoti, polymax, vardhman make with prior approval of Engineer in charge. |
| 127 | Supply of installation of Rubber mat 1m x 2m x 3mm. thick to withstand 1.1 KV dielectric strength as per IS : 5424 - 1969.Jyoti, polymax, vardhman make with prior approval of Engineer in charge. |
| 128 | Supply of Rubber gloves of 1.1 KV grade as per IS 4770-68.Jyoti, polymax, vardhman make with prior approval of Engineer in charge |
| 129 | Supply and Installation of 3 Pin 20A Modular type socket with Switch complete with front plate GI Box etc.for GeyserJyoti, polymax, vardhman make with prior approval of Engineer in charge. |
| 130 | Supply and Installation of 3 Pin 25A Modular type socket with Switch complete with front plate GI Box etc.for ACJyoti, polymax, vardhman make with prior approval of Engineer in charge. |
| 131 | Supplying, Receiving, unloading, shifting, installation, testing and commissioning of AMCA 210 certified Axial flow fan. Fans shall be direct driven. Casing shall be constructed of heavy gage sheet steel. Fan casing, motor mount and straightening vane shall be of welded steel construction. Motor mounting plate shall be minimum 15 mm thick and machined to receive motor flange. The inlet and outlet of the casing shall be fitted with flanges for ductwork connection and other accessories as required. The surface finish shall be Powder coated. Rotor hub and blades shall be cast aluminium construction. Blades shall be dieformed aerofoil shaped for maximum efficiency and shall vary in twist and width from hub to tip to effect equal air distribution along the blade length. Fan blades mounting on the hub shall be statically and dynamically balanced. Extended grease leads for external lubrication shall be provided. Motor shall be energy efficient ( minimum IE- 3) squirrel-cage, totally-enclosed, fan cooled, standard frame, constant speed, continuous duty, single winding, suitable for 415±10% volts, 50 cycles, 3 phase AC power supply, provided with class `F’ insulation. Motor shall be specially designed for quiet operation. The speed of the fans shall not exceed 1000 RPM for fans with impeller diameter above 450 mm, and 1440 RPM for fans with impeller diameter 450 mm and less. For lowest sound level, fan shall be selected for maximum efficiency or minimum horsepower. Each fan shall include all accessories necessary for proper fan operation. Static pressure : The Indicated static pressure is only provisional. Contractor to calculate static pressure based on final approved construction drawing and pressure drop of finalized Equipment/Items and submit for review/approval to the Design consultants. The procurement shall be processed only after duly verification / approval of calculation and selection from the Client/design consultant. All accessories like vibration isolators,Bird Screen, metallic gravity (Non-return) louvers and Sound attenuator (wherever required) shall be included in the cost of fan. The unit shall be BMS compatible with open protocol for software integration. The static pressure is 35mm of wg. BASEMENT PARKING EXHAUST. (21000 CFM).HUMIDIN, KRUGER, GREEN HECK make with prior approval of Engineer in charge. |
| 132 | Supply. Installation, testing and commissioning of AMCA certifed Cabinet fans. The fan shall be complete with centrifugal impeller, casing, direct driven motor and vibration isolators. Direction of discharge, and rotation position shall be as per the job requirement and shall be marked on the fan assembly. In case of lower ceiling heights the unit shall be with swing out motor type fans Housing shall be constructed of hot rolled GSS sheets in double skin construction. Housing metal parts shall be either spot welded or screwed or mounted together with rivets. Indication showing rotation arrow and make, model number and duty conditions of the fan shall be available on the housing. Fan Wheel shall be forward curved type. Fan wheel shall be statically and dynamically balanced. Fan motor shall be suitable for 230plus10% volts, 50 cycles, 1 phase power supply, squirrel cage, totally enclosed fan cooled motor (IP-44/IP-55), provided with class B or F insulation. Motor shall be with built-in thermal contact which will open and break the power supply at critical high temperature point. General Exhaust for Service Rooms. (2000 CFM) HUMIDIN, KRUGER, GREEN HECK make with prior approval of Engineer in charge. General Exhaust for Service Room. HUMIDIN, KRUGER, GREEN HECK make with prior approval of Engineer in charge |
| 133 | Design, manufacture, supply, installation, testing and commissioning of the following cubicle type, dead front, sheet steel, wall mounted control panels, including anchoring into the wall, wiring terminating into MCCB and copper earthing, in each panel shall be provided by the electrical contractor. All wiring and copper earthing of motors from the panel shall be included. All outgoing shall be provided with stop / manual / auto/ selector switch to facilitate operation through BAS. All starters shall be provided with potential free contact for connections to Building Automation System.The panel shall include the following components and accessories.Suitable rating incoming MCCB/MCB. Suitable rating AC-3 duty contactor(s), overload relay with builtin single phasing preventor, star delta timer (For S/D starters).96 sq. mm. digital voltmeter, ammeter, selector switches, CTs and control MCBs. Phase indicating lights and control MCBs. Push buttons for manual start/stop of motor. ON status indicating light for starter with control MCB. Minimum 2 pole auto/manual selector switch and 1 NOplus1 NC potential free aux. contacts for use by Building automation system.Time delay relay for delayed restart of motor. Interlocking terminals and wiring for fire damper, motorized dampers etc. as per control scheme. The number of control panels shall be as follows: 25 amps MPCB, upto 7.5HPDOLstarter. (CONTROL PANEL FOR FANS) SCHINDLER, L and T, JOHSONS make with prior approval of Engineer in chargeONTROL PANEL FOR FANS. SCHINDLER, L and T, JOHSONS make with prior approval of Engineer in charge. |
| 134 | Supply, Fabrication, Installation and testing of Factory Fabricated G.I sheet metal ducts in accordance with the approved shop drawings and specifications and shall also confirm to the SMACNA specifications including standard accessories like supports, Vanes, dampers, links, access doors, levers and quadrants etc. as per specifications and drawings. The rates shall include all materials and labor for suspension and supporting arrangement of galvanized steel for Plenums, Ducts, complete with UL listed fire retardant factory fabricated flexible connection as per specifications. Contractor to provide bracing in the ducts as per IS/ SMACNA standards. ) DUCTOFAB, GSR and GP SPIRA make with prior approval of Engineer in charge.24 Gauge (0 – 750 mm) |
| 135 | Supply, Fabrication, Installation and testing of Factory Fabricated G.I sheet metal ducts in accordance with the approved shop drawings and specifications and shall also confirm to the SMACNA specifications including standard accessories like supports, Vanes, dampers, links, access doors, levers and quadrants etc. as per specifications and drawings. The rates shall include all materials and labor for suspension and supporting arrangement of galvanized steel for Plenums, Ducts, complete with UL listed fire retardant factory fabricated flexible connection as per specifications. Contractor to provide bracing in the ducts as per IS/ SMACNA standards. ) DUCTOFAB, GSR and GP SPIRA make with prior approval of Engineer in charge.22 Gauge (751 – 1500 mm) |
| 136 | Supply, Fabrication, Installation and testing of Factory Fabricated G.I sheet metal ducts in accordance with the approved shop drawings and specifications and shall also confirm to the SMACNA specifications including standard accessories like supports, Vanes, dampers, links, access doors, levers and quadrants etc. as per specifications and drawings. The rates shall include all materials and labor for suspension and supporting arrangement of galvanized steel for Plenums, Ducts, complete with UL listed fire retardant factory fabricated flexible connection as per specifications. Contractor to provide bracing in the ducts as per IS/ SMACNA standards. ) DUCTOFAB, GSR and GP SPIRA make with prior approval of Engineer in charge.20 Gauge(1501 – 2250 mm) |
| 137 | Supply, Fabrication, Installation and testing of Factory Fabricated G.I sheet metal ducts in accordance with the approved shop drawings and specifications and shall also confirm to the SMACNA specifications including standard accessories like supports, Vanes, dampers, links, access doors, levers and quadrants etc. as per specifications and drawings. The rates shall include all materials and labor for suspension and supporting arrangement of galvanized steel for Plenums, Ducts, complete with UL listed fire retardant factory fabricated flexible connection as per specifications. Contractor to provide bracing in the ducts as per IS/ SMACNA standards. ) DUCTOFAB, GSR and GP SPIRA make with prior approval of Engineer in charge.18 Gauge(Above 2250 mm) |
| 138 | Supply, Fabrication, installation and testing of sheet metal ducts in accordancewith the approved shop drawings and as required by the specifications for pressurisation and smoke extraction. Ducts shall be with 2 hour fire rating,fire retardant factory fabricated flexible connection as per specifications. DUCTOFAB, GSR and GP SPIRA make with prior approval of Engineer in charge24 Gauge (0 – 750 mm) |
| 139 | Supply, Fabrication, installation and testing of sheet metal ducts in accordancewith the approved shop drawings and as required by the specifications for pressurisation and smoke extraction. Ducts shall be with 2 hour fire rating,fire retardant factory fabricated flexible connection as per specifications. DUCTOFAB, GSR and GP SPIRA make with prior approval of Engineer in charge22 Gauge (751 – 1500 mm) |
| 140 | Supply, Fabrication, installation and testing of sheet metal ducts in accordancewith the approved shop drawings and as required by the specifications for pressurisation and smoke extraction. Ducts shall be with 2 hour fire rating,fire retardant factory fabricated flexible connection as per specifications. DUCTOFAB, GSR and GP SPIRA make with prior approval of Engineer in charge20 Gauge(1501 – 2250 mm) |
| 141 | Supply, Fabrication, installation and testing of sheet metal ducts in accordancewith the approved shop drawings and as required by the specifications for pressurisation and smoke extraction. Ducts shall be with 2 hour fire rating,fire retardant factory fabricated flexible connection as per specifications. DUCTOFAB, GSR and GP SPIRA make with prior approval of Engineer in charge. 18 Gauge(Above 2250 mm) |
| 142 | Supply, fabrication, installation and testing the Flexible connections constructed of fire resistance flexibledoublecanvassleeveasperthe approved shop drawings. |
| 143 | Supply, installation and testing of galvanised steelconstruction GI dampers within ducts to be provided with suitable ducts lever and quadrants for manual control ofvolumeof air flow and for proper balancing of the air distribution system.as per the approved shop drawings and specifications.DUCTOFAB, GSR and GP SPIRA make with prior approval of Engineer in charge. |
| 144 | Supply, installation, testing and commissioning of Motorised combined smoke and fire damper complete with control panel, inter connecting wiring at locations shown in approved shop drawings and specifications. DUCTOFAB, GSR and GP SPIRA make with prior approval of Engineer in chargeSmoke and Fire Dampers. |
| 145 | Supply, installation, testing and commissioning of Motorised combined smoke and fire damper complete with control panel, inter connecting wiring at locations shown in approved shop drawings and specifications. DUCTOFAB, GSR and GP SPIRA make with prior approval of Engineer in chargeControl Panel and Wiring , actuators |
| 146 | Supply, installation, testing and balancing of powder coated Extruded Aluminium supply Air Grilles with volume control dampers in accordance with the approved shop drawings and specifications. With horizontal fixed bars. DUCTOFAB, GSR and GREEN HECK make with prior approval of Engineer in charge. |
| 147 | Supply, installation, testing and balancing of Air Grilleswithout volume control dampers for return/exhaust air in accordance with the approved shop drawings and specifications. With horizontal fixed bars powder coated extruded aluminium. DUCTOFAB, GSR and GREEN HECK make with prior approval of Engineer in charge |
| 148 | Supplying, installation, testing and commissioning of GI construction fresh air louvers with bird screen painted in baked enamel shade with metallic frame work complete as per specification approved drawings and schedules. Louvers need to be suitable in order avoid rain water entry in to spaces @ 15 degree deflection with bird screen complete as per specification approved drawings and schedules. DUCTOFAB, GSR and GREEN HECK make with prior approval of Engineer in charge |
| 149 | Supplying , Installing, testing and commissioning of powder coated extruded aluminiumexhaust air louvers with bird screen with metallic frame work and fixing accessories , to be fixed on external wall to exhaust air from respective area to ambient, it shall be suitable for exhausting required air in CFM . Louvers need to be suitable in order avoid rain water entry in to spaces @ 15 degree deflection with bird screen complete as per specification approved drawings and schedules.DUCTOFAB, GSR and GREEN HECK make with prior approval of Engineer in charge |
| 150 | Supply, installation, testing and commissioning of back draft dampers in pressurization fans.DUCTOFAB, GSR and GREEN HECK make with prior approval of Engineer in charge. |
| 151 | Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m3, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paperand 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications. 25 mm thick. DUCTOFAB, GSR and GREEN HECK make with prior approval of Engineer in charge. |
| 152 | Supply, unloading, installation, testing and commissioning of the following cubical type panels made of 2.0 CRCA structure, base channe lSMC, doors and sheet metal partitions complete with, Moulded Case Circuit Breakers, meters, indicating lamps, current transformer, control MCB etc. Complete in all respects, insulated bus bars with heat shrinkable PVC sleeve, supported on FRP / SMC supports in suitable bus chambers, interconnection, small wiring, name plate, danger plate, earth bus etc. and comprising of compartments with hinged door for each feeder and its accessories, cable alley with hinged doors, bus chamber with bolted door etc. The panel being of dust and vermin proof construction with rubber gasket, attractively powder coated with Approved Paint shade. The panel shall be free standing type/ wall mounted type as per relavant drawing and comprising with foundation and Masonary works including ducting. Note:- Breaking Capacity of all MCCB`s are Ics Service Breaking Capacity. MCCB`s upto 250Ashall be with Adjustable thermal-magnetic and above 250A Microprocessor based adjustable release. All MCCB`s shall be Front door operating handle, Phase Spreaders and Phase Barriers. INNOVIC, ZENIA, ADLEC make with prior approval of Engineer in charge TPN MCCB Shall mean 3Pole MCCB with Adequate size of separate neutral link. Metering CTs burden shall be 15VA and accuracy class 1.0. CTs shall be `CAST RESIN`type . All indication lights shall be LED type. All meters shall be `DIGITAL` type. Degree of Protection for Indoor panels shall be IP-55 with canopy and double for Outdoor Panels, cable entry from bottom only.Panel space heaters with control MCB and Thermostat, covered CFL lamp controlled by door switch for each panel bay. Gland plates shall be 2mm thick for LT. Panels upto 400A Incomer and 3 mm thick for LT. Panel with 630A and above incomer. Panel Manufacturer should have Type Test Certificates for Short Time withstand current test of 50KA for 1.0 Sec from CPRI Bhopal / Bangalore.`ON` Indicating lamp shallbe provided for all 3 phase MCCBout going feeders unless otherwise specified.Control SP MCB`s of 2 /4A Rating shall be provided for each metering circuit. MDB (Faculty Block) Incoming 1 No. 630 Amp FP MCCB (of 36KA Ics Value) with microprossor release for O/L, S/C and E/F protection. Bus bars 1 Set of 800-Amps, 3-Phase, 4-wire, 415 volts, 50 Hz Aluminium bus-bars with colour coded PVC heat shrinkable sleeves (Neutral to be equal to phase size). Metering and Indication One set of R/Y/B phase indication Lamp and MCB. 1 No. Multi Function Meters (A/V/kW/kWh) ON/OFF/TRIP indication lamp for incomer Outgoing 7 Nos. 160 Amp TPN MCCB of 36 KA with overload, S/C protection 4 Nos.100 Amp TPN MCCB of 36 KA with overload, S/C protection 3 Nos. 63 Amps. TPN MCB of 10KA 5 Nos. 40 Amps. TPN MCB of 10KA 3 Nos. 32 Amps. TPN MCB of 10KA Panel as mentioned above should be complete in all respect with internal wiring, al. bus bar etc |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
