Tender For Sitc Of Network, Cctv, Wifi At New Building Uda Office, Udaipur. (3007) - Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC, UTP (Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Indoor Cable as per latest ammendments of ANSI/TIA/EIA-568 , The copper conductors should be balanced twisted in pairs, seperated by a cross-member fluted pair divider & protected byPVC Jacket. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies up to 250 Mhz. in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 2 Supply Drawing and Testing of stranded Single mode (9/125 µm) glass optic fiber cable as per latest ammendments of TIA/EIA 568/ISO/IEC construction of LSZH outer sheath cable cable should be used for LAN and WAN back bones . With its LSZH sheathing these cables should be ideal for indoor/outdoorinstallations in existing MS/PVC /HDPE Conduits/ slotted channels with ferruling at both ends for identification complete in all respect.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work refer Annexure A attached with this BSR . 6 Fiber 3 Supply Installation OTDR Testing & Fusion Splicing of Fiber Singlemode Pigtail (9/125 µm (OS1/OS2) made of glass fiber optic with semi-tight buffer PA/PBT Ø 0.9 mm yellow singlemode G652.D (9/125 µm (OS1 OS2) should have length of min 1.5m should be fitted at one end with any one type of single ST/E-2000/SC/LC/MT-RJ/PC type connector in acc. withIEC 61754-20 Should be delta IL < 0.2 dB after 500 mating cycles It should be Zirconia (ceramic) ferrule with a PC polished endface geometry connector qualified in acc. with IEC 61753-1 for category U (uncontrolled environment). and qualified in acc. with IEC 61753-1 Performance acc. to IEC 61753-1 (Table A.12) as per latest ammendments of TIA/EIA 569B.3 Standard Specification as per requirments.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work refer Annexure A attached with this BSR . 4 Supply Installation & Testing of Indoor duplex Singlemode patch cord (9/125 µm (OS1/OS2) made of glass fiber optic with LSZH jacket F8 2.0x4.1 mm yellow singlemode G652.D (9/125 µm (OS1 OS2) Mounted on both sides with ST/E-2000/SC/LC/MT-RJ/PC type Duplex connectors in acc. with IEC 61754-20. Zirconia (ceramic) ferrule with a PC polished endface geometry connectors should be tuned in accordance with IEC 61755-3-1 and qualified in acc. with IEC 61753-1 for category U (uncontrolled environment duplex clip and white plastic dust cover should comply to delta IL < 0.2 dB after 500 mating cycles there should be an optional Visual coding mechanical coding and lock protection on the patch cords which can be added on later stage. patch cordss performance should be acc. to IEC 61753-1 (Table A.12) as per latest ammendments of TIA/EIA 569B.3 as per requirements.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work refer Annexure A attached with this BSR .Single Mode Patch Cord 2 Mtr. 5 Supply Installation & Testing of 19 1U Rack Mounted/ surface mounted aluminum/ CRCA 1.2mm powder coated Singlemode glass Fiber Optic Cable Patch panel/LIU loaded with flangless/screwable duplex adapters for ST/E-2000/SC/LC/MT-RJ/PC type It should have easy removable Top plate with push buttons there should be a splice tray installed in the Patch panel/LIU which can handle the fiber cores splice tray should be PC+ABS material it should include accessories like mounting hardware gormetts heat shrink tubes/sleevs screws nuts to install the panel for rack/wallmount applications as per requirment complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work refer Annexure A attached with this BSR . 12 Port 6 Supply & Installation of IP-20 & IK-08UL ListedWall mounted Double Section Communication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheet front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass doorVertical Mounting Rail 1.6 MM with UMarkingwith All round protective channel on the door aperture lock integrated on front door top and bottom cover with cable entry provision with gland plates integrated side walls 2 pair of 19 angles with wall mounting provision on wall. Accessories like: 1 No of 19 1U Horizontal Cable manager 1 No of 90 cfm 230V AC Fan with 1 mts long cable mounting hardware1 No of 19 1U mountable socket strips with 5 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches fans etc along with earth continuity kit indicator moulded power supply cable. fixing on wall with Suitable Anchor fastneretc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work refer Annexure A attached with this BSR .15 U Rack with Width 600 mm & Depth 400 mm + 100 mm 7 Supply & Installation of IP-20 & IK-08UL Listed Communication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheetVertical Mounting Rail 1.6 MM with UMarking front sturdy sheet steel frame folded from one piece and welded with 5mm toughened glass door with All round protective channel on the door aperture lock integrated on front door top and bottom cover with cable entry provision with gland plates integrated side walls Set of 75 mm height 4 castors 2 of which have brakes Accessories like: 5 Nos of 19 1U Horizontal Cable manager 2 Nos of vertical cable managers 1 no. Keyboard Tray4 Nos of 90 cfm 230V AC Fan with 1 mts long cable mounting hardware2 No of 19 1U mountable socket strips with 6 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches fans etc along with earth continuity kit indicator moulded power supply cable complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work refer Annexure A attached with this BSR . 17 U Rack with Width 600 mm &Depth 800 mm 8 Fiber Fusion Splicing with OTDR Testing of Fiber Single/ Multi mode (per splice) of glass Fiber Optic Cable including cleaning the cable and making splice as per standard practice complete in all respect.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work refer Annexure A attached with this BSR . 9 Supply and Installation of unsheilded/360 degree sheilded Information outlets made of high impact plastic body with ABS FR Grade halogen free material with provision for protection against dust in jack suitable for Cat 6/6A application complying to latest ammendments According. to Cat. 6/6A channel It should support channel as well as components requirements of Cat.6/6A standards at frequencies of up to 250 to 500 Mhz. Cat 6/6A unshielded/shielded Jack should be suitable to terminate 4 pair 23/24 AWG solid/stranded wire diameters using 100 Ohm unshielded/shielded balance twisted pair cable the jack should have tooless/impact termination on reliable copper tin plated Insulation displacement contact with easy lock mechanism It supports IEC 60603-7-4 and complied with ANSI/TIA/EIA 568 C.2 standard. jack should be RJ11RJ12 & RJ45 compatible. Should support Ethernet 1.2 Gb/s ATMDigital video and broadband/baseband analog video Voice over internet protocal (VOIP) Specifications in existing modular/MS Boxes along with necessory connections as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work refer Annexure A attached with this BSR .Cat 6 Un-sheilded Information Outlet 10 Supply & fixing of square Faceplate for Flush / Surface Mount Information Outlets Single/Dual or Quad Aperture material should bePC+ABS body Suitable for RJ45 unshielded/shielded connection modules. Should match with I. O. OEM. Dimensions should be 86mm X 86mm as required complete in all respect.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work refer Annexure A attached with this BSR .Single Aperture 11 Supply & fixing of square Faceplate for Flush / Surface Mount Information Outlets Single/Dual or Quad Aperture material should bePC+ABS body Suitable for RJ45 unshielded/shielded connection modules. Should match with I. O. OEM. Dimensions should be 86mm X 86mm as required complete in all respect.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work refer Annexure A attached with this BSR .Dual Aperture 12 Supply Installation Testing and Comissioning of Rack mounted 19 1U Cat6 24 Port loaded 1.5-1.6 MM CRS chasis powder coated sheet steel made of plastic (ABS) Modular Patch Panelswith Rear Cable management system and mounting hardware to mount the patch panel. Should have port identification numbers printed/engraved on front of the panel. Etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work refer Annexure A attached with this BSR .Modular Patch Panel Loaded with Cat -6 I/O 13 SupplyInstallation and Testing of 4 pair 100 Ohm impedance Cat 6/6A /Class E/Ea patch cords should be constructed of minimum 23/24 AWG stranded bare Copper cable with FRPVC/LSZH Jacket with an enhanced performance by factory moulded RJ45 connectors with strain relief boots as per ANSI/TIA/EIA 568-C.2 suitable for Cat 6/6A application complying to latest ammendments Category 6/6A Standards According. to TIA568C.2 ISO/IEC 11801 EN 50173 IEC 60603-7-51 EN 60603-7 IEEE 802.3an minimum requirement for 1G BASE-T to 10G BASE-T performance. Patch cords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes should support IEEE 802.3af / IEEE 802.3at for POE applications Minimum 750 to 1000 mating cycles in plug contacts for long durability Should support Ethernet 10GBASE-T 1.2 Gb/s ATM Token ring 4/16 Digital video and broadband/baseband analog video Voice over internet protocal (VOIP).All as per pre approved by Engineer in charge.For additional technical parameters of products/ work refer Annexure A attached with this BSR . Cat 6 U/UTP (Unscreened/Un-sheilded Twisted Pair) Patch Cord 1 Mtr 14 SupplyInstallation and Testing of 4 pair 100 Ohm impedance Cat 6/6A /Class E/Ea patch cords should be constructed of minimum 23/24 AWG stranded bare Copper cable with FRPVC/LSZH Jacket with an enhanced performance by factory moulded RJ45 connectors with strain relief boots as per ANSI/TIA/EIA 568-C.2 suitable for Cat 6/6A application complying to latest ammendments Category 6/6A Standards According. to TIA568C.2 ISO/IEC 11801 EN 50173 IEC 60603-7-51 EN 60603-7 IEEE 802.3an minimum requirement for 1G BASE-T to 10G BASE-T performance. Patch cords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes should support IEEE 802.3af / IEEE 802.3at for POE applications Minimum 750 to 1000 mating cycles in plug contacts for long durability Should support Ethernet 10GBASE-T 1.2 Gb/s ATM Token ring 4/16 Digital video and broadband/baseband analog video Voice over internet protocal (VOIP).All as per pre approved by Engineer in charge.For additional technical parameters of products/ work refer Annexure A attached with this BSR . Cat 6 U/UTP (Unscreened/Un-sheilded Twisted Pair) Patch Cord 2 Mtr 15 SITC of IR IP Based 5 MP Dome camera: 1/2.8 Progressive CMOS, ICR, IR, 2560(H)x1920(V):25fps(P) 2.8/3.6 mm lens (As per site requirement) H 264,H265/MJPEG, dual-stream, 120dB WDR or better, 3D DNR, BLC, IR: minimum 30 mtr, Provision for Support on-board storage up to 256 GB (SD card not included), intrusion detection, Line crossing detection, Motion detection, Dynamic analysis, Alarm should be trigger on (Tampering alarm, Network disconnect, IP address conflict, Storage exception), security feature such as (password protection, privacy mask, watermark, IP address filtering, anonymous access), Open standard to support ONVIF (PROFILE S, PROFILE G), Metal Housing, Vandal-proof housing IP 67, DC 12V & PoE, Complete with Junction box for cable management Oerating Conditions: 20 °C 50 °C or better. Model should be CE, BIS, /UL, FCC, ROHS compliance. The CCTV OEM should have CMMI Level 5 or above or equivalent setup certification. The CCTV OEM should have its office and service/ support center in RajasthanAll as per pre-approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure A attached with this BSR. 16 SITC of IR IP based 5 MP Bullet Camera 5 MP Video Resolution: 2592(H)x1944(V) Pixels, 1 to @25 fps; Image Sensor: 1/2.8-inch CMOS; Built in Infra-Red: 40 to 50 mtr; High Dynamic Range 120 dB WDR; Lense- 2.8/3.6 mm, H264,H265/MJPEG, provision for Support on-board storage up to 256 GB (SD card not included), intrusion detection, Line crossing detection, Motion detection, Dynamic analysis, Alarm should be trigger on (Tampering alarm, Network disconnect, IP address conflict, Storage exception), security feature such as (password protection, privacy mask, watermark, IP address filtering, anonymous access), Open standard to support ONVIF (PROFILE S, PROFILE G), Metal Housing, Vandal-proof housing IP 67, DC 12V & PoE, Complete with Junction box for cable management Operating Conditions: -30°C to +70 °C or better. Onvif Profile S, G, Confirmant; Model should be: CE, BIS,/UL, FCC,ROHS compliance The CCTV OEM should have CMMI Level 5 or above or equivalent setup certification. The CCTV OEM should have its office and service/ support center in RajasthanAll as per pre approved by Engineer in charge. For additional technical parameters of products/work, refer Annexure A attached with this BSR 17 Supply, Installation, Testing and Commissioning of 10G SFP+ single mode duplex SFP module which can support upto 10KM.Fiber Channel LC Type Duplex Connector 1310 nm laser transmitter Should support distance upto 10 km on 9/125 um of data rate upto 10Gb on bi-directional data links. Should also support industrial temperature should have metal enclosure for lower EMI. The transceiver should be ROHS Compliant. (For Each SM Fiber) all switches & related Fiber modules should be of same make & category for seamless integration with each other of Enterprise class. 18 SITC of 64CH NVR 64 ch IP Camera Input Third Party IP cameras Supported with ONVIF Conformance Supports H.265/H.264 Video Formats Supports 12 Megapixels Resolution Recording Supports 2 ch-HDMI, 1 ch-VGA, 1ch-CVBS (HDMI2 at 4K resolutions) HDMI1/VGA & HDMI2 independent outputs provided I/O Bandwidth: 320/320 Mbps supports 8 SATA upto 64 TB Supports RAID 0, 1, 5, 6, 10 Various Fish eye dewarping modes for live view & playback for both web interface & GUI Supports N+1 Hot Spare Supports 12V Power Output ANR Technology to enhance the storage reliability when the network is disconnected Supports Cloud upgarde. 19 SITC of Outdoor Rack Usage/Application Outdoor - CCTVSurveillance,Wifi, Smart City Type OUTDOOR Material Galvanized Steel ShapeRectangular IP Rating IP55 Color RAL 7035 Size 6U 600x400 20 SITC of 8 TB Surveillance Hard drive to keep backup of all cameras recording. 21 Supply & laying of HDMI 4k Cable 05Mtr. 22 Supply & laying of HDMI 4k Cable 10Mtr. 23 Supply & laying of HDMI 4k Cable 15Mtr. 24 Supply & laying of HDMI 4k Cable 20Mtr. 25 Supply and Installation of 8 Port HDMI 4K Supported Splitter. 26 :Supply & Laying of10 MTR. VGA Cable 27 Supply & Installation of 1U cable manager to dress the cable in racks. 28 Supply & laying of 3.0 EXTENSION CABLE (ACTIVE) - 20 MTR 29 Supply, Installation, Testing and Commissioning Of 5 KVA Online UPS True online double-conversion topology and zero transfer time to battery provides,Wide input voltage range allows the UPS to operate in harsh electrical environments and extends battery life,AC-start function allows the UPS to be switched on without connecting to a battery, Programmable load bank disconnects non-critical loads when a blackout occurs and reserves more battery power for critical loads, Up to four units parallel capacity allows redundancy and load expansion, Hot swappable batteries ensure continuous operation eve. 30 Supply, Installation, Testing and Commissioning of Battery 12V 65 AhBatteries for backup of approx 120 min. 31 Supply, Installation, Testing and Commissioning Of Battery interlinks cable with Stand. 32 Supply, Installation Testing and Commissioning of Managed Layer-2 Intelligent Giga Ethernet Switch providing 24x1G, 2x10G, and 2xSFP+ (provision for Fiber Giga connectivity) all switches & related Fiber modules should be of same make & category for seamless integration with each other of Enterprise class for additional technical parameters of products/ work refer Annexure. 33 Supply, Installation Testing and Commissioning of Managed Layer-2 Intelligent Giga Ethernet Switch 24x1G PoE+ 2x10G, 2xSFP+ Managed Switch PoE Budget 480W w/1 PSU, 480Ww/2 PSUs in RPS mode, 720W w/2 PSUs in EPS moderelated Fiber modules should be of same make & category for seamless integration with each other of Enterprise class For additional technical parameters of products/ work refer Annexure. 34 Supply, Installation, Testing and Commissioning of Fast Dual-Band Wi-Fi-6:Business class WiFi based on next generation 802.11ax WiFi 6 technology on both 5GHz and 2.4GHz bands. (Backward compatible to 802.11b/g/ n/a/ac) Ultimate speed and capacity with WiFi 6 Enterprise level security with WPA3 and 8 separate wireless networks (SSIDs) High speed and easy wiring with a 2.5GbE port with PoE Mesh capabilities for seamless roaming and highly scalable coverage areas. Dual band 2x2 (2.4GHz and 5GHz) 4 streams of data for an aggregate throughput of up to 3Gbps.Enterprise security and Enhanced Open. 35 SITC of PVC boxes with accessories Camera .
