Tender For Special Repair To Bldg No P-345 Chq Cook House At Src Ramgarh Cantt; 1 Taking down complete existing roof /parapet treatment any thickness including plastering, leaping plaster ofany thickness cutting & up rooting tree roots/Vegitable growth & removing the all loose particle from roof & alldebris from the premises upto 500m from the MOD land including cleaning/washing down and keeping surfaces cleancomplete all as specified and as directed. 2 M & L for plain cement concrete (PCC) (1:2:4) ,type B-0 (using 12.5mm graded crushed stone aggregate)as in padding, benching, sunken portion etc., on roof surface for correcting/ required/making proper slope on roof, etc.,and finished the surface without using extra cement complete all as specified and directed. 3 M & L for application of water proofing treatment using APP modified roof membrane over non accessible/non approachable RCC roof slab /chajjah/canopy /parapet wall( horizontal /vertical surface) to be executed through approved applicator of the membrane manufacturer/authorized applicatorof the manufacturer with following specification etc complete all as specified and directed :-(a) Cleaning existing naked roof surface properly with wire brush.(b)Applying forrendering 10 mm thick in cement mortar 1:3 on concrete / brick surfaces mixed with polymer based liquid water proofing compound@ 200 ml/50 Kg per Bag of cement ,finished, even and smooth without using extra cement over roof / sunken slab /wall complete(c) Applying approved bituminousbased primer(conforming to IS: 3384-1995) @ 0.50 litre / Sqm manufactured by the same agency as that of APP membrane with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface.(d) Laying not less than 3mm thick APP (Atactic polypropylene Polymer modified prefabricated membrane) modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gms/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Physical property of membrane shall be as under :-(i) Membrane weight not less than 3.00 Kg/Sqm. (ii)Non woven polyester weight not less than 160 gms/Sqm.(iii)Softening point of membrane not less than 150degree Celsius. (iv)Joint tensile strength-longitudinal not less than 150 Kg / Sqcm and transverse not less than 450 Kg /Sq.cm at230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N& transverse not less than 250N.(vi)Elongation of reinforcement not less than 30%.(vii) Impermeability under water pressure not less than 3 Kg/Sqcm.(e) APP modified polymeric membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (f) Applying two coat of bituminiousbased Aluminium Paint @ 0.3 Kg /Sqm over APP Membrane. 4 S&F rotational moulded polythene water storage tank of capacity 1000 ltrs (Cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and20 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) including taking down of existing tank complete all as specified and directed. 5 S & F in repair 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 6 S & F in repair 15mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 7 Taking up or down steel tubing and connections of 20 mm bore or removal to store complete etc and making good the disturbed surface in cement mortar 1:3 complete all as specified & directed. 8 S&F for GI water tubing mediumgrade, ISI marked,galvanised, 20 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls /laid in trenches and ceiling or laid in floors including cutting chasees for brick wallsand making good the surface in cement mortar 1:3 complete all as specified & directed. 9 Taking up or down steel tubing and connections of 15 mm bore or removal to store complete etc and making good the disturbed surface in cement mortar 1:3 complete all as specified & directed. 10 S&F for GI water tubing mediumgrade, ISI marked,galvanised, 15 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls /laid in trenches and ceiling or laid in floors including cutting chasees for brick wallsand making good the disturbed surface in cement mortar 1:3 complete all as specified & directed. 11 Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.50 sqmeach and removing from site and making good the disturbed surface of walls in cement mortar (1:3) complete all as specified & directed. 12 Taking down chowkhats or frames with shutters (without taking off shutters from the frames)exceeding 1.50 Sqm but not exceeding 4.00 sqmeach and removing from site and making good disturbed surface of walls in cement mortar (1:3) complete all as specified & directed. 13 S & F factory made uPVC door frame made of uPVC. extruded sections having an over all dimension (extruded section profile) 42 mm x 50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized mild steel tube of size 19 mmX 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge 14 S & Ffactory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 mmx 64 mm & sash 67 mm x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 mm x 8 mm size for fixing frame to finished wall and necessary stinless steel screws, etc.Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in-Charge 15 S & F factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 mm x 50 mm mullion 47 mmx 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.)comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile),uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100mm x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixinghardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. 16 S&F for anodised aluminiumDeco grills size4mmx4mm, 10mm thick(DG-104) and aperture not exeeding 50 mmX 75 mm width and including fixing with U-aluminium channel, with steel screw and tint match for windows, ventilators etc. with & including aluminium fittings such aslocking arrangement complete all as specified and as directed. 17 S&F steel window with sidehung shutters including boxtype hinges with steel handles and steel peg stay complete with glazing bars, dovetailed or weldedwith four Nos mild steel flat iron 25 mm X 3mm ,200 mm length (appx) & two Nos mild steel tower bolt 150 mm long and one peg stay on each leaf complete all as specified and directed 18 S&F steel window with sidehung shutters including box type hinges with steel handles and steel peg stay complete without glazing bars, dovetailed or weldedwith four Nos mild steel flat iron 25 mm X 3mm ,200 mm length (appx)& two Nos mild steel tower bolt 150 mm long and one peg stay on each leaf complete all as specified and directed 19 M&L for prepartion ofnew or previously untreated steel surface of any description ,not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified & directed. 20 S&F150 mm long aluminium anodised barrel tower bolts of extruded section and fixed all as specified and directed. 21 S&F 150 mmlong aluminium alloy handles of cast type, anodisedcomplete all as specified& directed. 22 S & F in repairfor aluminium (extruded section body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61Kg to 80 Kg and fixed complete etc all as specified & directed. 23 S&F of brass mortice lock,vertical type, size 100 mm long four levers (ISI marked) including escutcheon plates and two keys complete all as specified and directed. 24 M & L for 4.8mm thick plain sheet glass ordinary quality and glazing with oil puttyexceeding 0.50 Sqm in each pane,complete all as specified and as directed by Engr-in-Charge . 25 S & F for 3.0 mm thick sheet tinted glassand glazing with oil putty not exceeding 0.50 sqm each pane complete all as specified and directed. 26 S& F 3.0 mm thick frosted glass pin headed type in squares/ rectangularexceeding 0.5 Sqm ineach pane glazing with oil putty or aluminium frame / shutters with rubber neoprene beadingcomplete etc all as specified & directed. 27 S & F for Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 28 M&L for framed work such as grills,gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railing; framework of water tanks and similar work conforming to Fe 290- Gde E -165& for portions framed and hung as gates, including pintle hinges, stops,hand-made sliding bolts, etc.complete all as specified and as directed 29 S & F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes suppyling & fixing in opening as per specification & drawing complete all as spcefied and directed by Engr-In-Charge . 30 S & F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS framed shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail &bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS framed welded/sealed to stiles & rails with suitable PVC sheet beading & joined together with solvent cement complete all asfixing in the frame at site as per specification and drawing including 3 Nos stainless steel butt hinges 100 mm long for each door, complete all as specified and as directed. 31 S & F 100mm sizebutt hinges medium weight cold rolled mild steel complete all as specified and directed . 32 S & F in repair 19mm/20 mm dia curtains rod of chromium plated mild steel tubingwith fixing for fancy type brackets,stops, rollers etc.,complete all as specified and as directed by Engineer-in-Charge. Note: Running length of curtain rodshall be measured & paid only. 33 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the allrubbish off from the premises complete all as specified and directed. 34 M & L glazed ceramic coloured tiles of size 375 mm x 250 mm x7mm/450 mmx 300 mm x7 mm thick,as in dado/skirting etc ,set and jointed in neat cement slurry and pointed in colour cement to match the tiles including 10 mm thick rendering in cement plaster in CM (1:4) complete all as specified and directed. 35 M & L joint free non skid coloured ceramic tiles 7 to 8 mm thick (sqaure/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., over and including 15mm thick screed bed in cement mortar (1:6) ,set and jointed in neat cement slurry and pointed in coloured cement to match the existing surfaces,complete all as specified and directed. 36 M&L for10mm thick vitrified ceramic tiles( light shade) polished area of each tiles exceeding 0.42 sqmbut not exceeding 1.00 sqmas in floors,set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles ,laid over & including 15mm thick screed bed in CM 1:6 complete all as specified and directed. 37 M&L for coloured non digital paver Vetrifiedexteriorfloor tiles300 mm X300 mm X 10 mm thick ,in floors etc set & jointed in neat cement slurry and pointed in cloured cement to match the shade of tiles, over & including 15 mm thick screed bed in cement mortar (1:6) etc complete all as specified &directed. 38 Dismantling stone slabs of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar, and removal of debries from site complete all as specified and directed. 39 M&L for mirror polish machine cut kota stone slab flooring 18mm to 20 mm thick( size not less than 575 mm X 575 mm), laid & jointed with grey cement slurry @ 2.0 Kg per sqm mixed with pigment to match the shade of the slab including grinding, rubbingwith beeswax polishing into mirror finish over & including 20 mm thick screed bed in CM (1:4) complete all as specifed & directed. 40 M& L for mirror pollish machine cut Kota stone slab 16 to 18mm thick as in vertical surfaces such as skirting/dados in narrow width, laid and jointed with grey cement slurry pointed with coloured cement to match the shade of the slab including grinding rubbing with beeswax polishing into mirror finishover 10 mm thick backing coat in CM (1:3) etc complete all as specifed & directed. 41 M&L for bees-wax polishing on existing Kota floor surface of any description including cleaning and preparing the surface complete all as specified and directed. 42 M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth in brick wall complete all as specified and as directed. 43 Demolition of plain cement concrete(un-reinforced ) in ground floors, terrazo tiles floor & paving not exceeding 15cm thickness (below or above ground level) and removal of rubbish off from sitecomplete all as directed by Engr-in-Charge. 44 M & L for 75 mm thick plain cement concrete (1:3:6) mix, type C-2 (using 40mm graded crushedstone aggregate ) as in plinth protection, finishing the surfaces even and fair without using extra cement, including 10 mm wide, 75mm deep joints made at 3.00 m in length and filled with bitumen 85/25 gradeand sand in the ratio 1:3 including necessary form work , complete all as specified and directed. 45 Demolition of reinforced cement concreteof any description such as in chullah hoods, shelves, cover slab and platform, etc,and removal of rubbish off from outside of MoD land, complete all as directed by Engr-in-Charge. 46 M & L for RCC (1:2:4)type B-1 (using 20mm graded crushed stone aggregate) slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary form work complete all as specified and directed. 47 M&L for precastreinforced cement concrete 1:2:4 ,type B-1 (using20 mm gradedcrushedstoneaggregate)as in kitchen platform, shelves ,man hole cover slab, etc. including necessary formwork complete all as specified and directed.Note : Reinforcementwill be measured & paid seperately under respective item of BOQ. 48 M&L for mild steel TMT bars 10mm dia and over grade Fe-500D, cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed. 49 M&L for 18 mm thick granite slab (or any type) table rubbed and pre mirror polished in steps,jambs, pillar,window cill,cooking platforms and like in cement mortar1:4, set & jointed in neat cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over & including 15 mm thick rendering in cement mortar(1:4)etc including dismantling of exsting slab complete all as specifed and as directed. 50 S& Fin repair vitreous China wash basin counter top, star white oval type size 560 mm X 410mm including 32 mm brass chromium platedwaste coupling ,PVC 32 mm bore waste pipe, chromium plated grating & making good disturbed surface with CM 1:3 complete all as specified and directed by EIC.Make Hindware CAT No 10017 or equivalent Cat Part No. of any make as per appendix A to P.S as approved by GE). 51 S&Fin repair kitchen sinks made of stainless steel 1.00 mm thick sheet with plugs, washers & waste coupling and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495 mm X 420 mm bowl size 410 mm X 330 mm X 160 mm including 40 mm bore PVC flexible waste/flush pipe 800mm long with socket fixed with sinkbrass waste coupling complete all as specified and directed. 52 M&Lvitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe),including connection to drain (or outgoing pipe, and to flushing pipe & antisyphonage pipe etc with aluminium hinging device including plastic seat cover & taking down existing pan & making good disturbed surfacecomplete all as specified &directed. 53 S & F in repair PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including ball valve float and handle, PVC flush pipe 32 mm bore & PVC connection 15 mm bore 450 mm long with PTMT nuts and brackets complete set & making good disturbed surface with CM 1:3 complete all as specified and directed. 54 S & F in repair health faucet(ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 m long flexible tube and ABS wall hook including making connection & fixed in position complete all as specified & directed. 55 S&F in repair stop cockfancy type chromium platedcast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15 mm bore complete all as specified &directed. 56 S&F in repair 15mm bore long body (weight not less than 400 gm)bib tap, cast copper alloy, CP fancy type with crutch or butterfly handle, screw down, screwed for iron pipe or for brass ferrule including flange complete all as specified and directed 57 S & F in repair pillar taps long body chromium plated, cast copper alloy with capstan head, chromium plated, screwed down with or without lettered Hot or Cold with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore complete all as specified & directed 58 S&F in repair chromium plated (CP) soap tray of size 160 mm x160 mm x 90mm, complete all as specified and directed. 59 S & F in repair Grating doom 100mm dia of PTMT (minimum weight 25gms) complete all as specified and directed by Engineer-in- Charge. 60 S & F in repair Grating doom 125mm dia with waste hole of PTMT (minimum weight 40gms) complete all as specified and directed by Engineer-in- Charge. 61 S&F in repair for PVC connection 15 mm dia size with PTMT nuts of length 450 mmcomplete all as specified and directed. 62 S&F in repair towel railbrass chromium plated towel rail , 20 mm dia ,D-type 600 mm long between flangesfixed with and including chromium platedbrass screw & wooden /plastic cleats complete set all as specified and directed. 63 S & F in repair 32 mm diabore waste pipe fixed to wash hand basin complete all as specified and directed by Engineer-In- Charge. 64 S & F 75mm dia PVC (SRW) floor trap with grating including joining to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engr-In-Charge. 65 S & Fin repair 110 mm dia PVC(SWR) WC connector with lip ring, complete all as directed and as specified. 66 S& F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed 67 Demolition of brick work of any description and in any position built in cement or cement lime mortar including all quoins, arches, pillars including segregation of serviceable bricks for reuse & removal of rubbish out offfrom site etc complete all as specified and directed. 68 M&L for Brick work with sub class Bbricks ,straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6etc complete all as specified & directed. 69 M&L for rendering 10 mm thick onfair face of brick masonry/concrete surface etc in cement mortar (1:6) surface finished even & smooth without using extra cement complete all as specified and directed. 70 Taking down cement plaster on brick wall or concrete surface etc including raking out joints hacking for key scrubbing down with water etc& removing the debris from the premises upto 500 m from the MOD landcomplete all as specified and directed. 71 M&L for 15mm thick rendering (external) on brick or concrete surface in cement mortar 1:4, finishing surface even and smooth without using extra cement complete all as specified and directed. 72 M&L for repair and rendering 10mm thick in cement mortar 1:3 on chajjas not exceeding 60cm width after removing cracked plaster and concrete surface including cleaning of visible reinforcement and treating with cement slurry also necessary repair to cracked concrete if any with cement concrete 1:2:4 type B-0( using 12.5mm graded crushed stone aggregate )including necesssary scaffolding work for double/single storey building complete all as specified and directed. 73 M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces withpreparation ofplastered surfaces andapplyingtwo coats of distemper oil emulsion (OBD) over a coat of alkali resistant primer (from same manufacturer of OBD)and a layer of wall care putty not less than 2mm thick complete all as specified and directed. 74 M&L for complete removal of existing treatment from ceilings(any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces withpreparation ofplastered surfaces andapplyingtwo coats of distemper oil emulsion (OBD) over a coat of alkali resistant primer (from same manufacturer of OBD) over& including 2.0 mm thick wall care putty complete all as specified and directed. 75 M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces withpreparation ofplastered surfaces and applying two or more coats of acrylic smooth exterior paint of required shade new work (two or more coats applied @ 1.67 Ltr/10 Sqm and including priming coat of exterior primer applied @ 2.20 Kg/10 Sqm,applying by bump roller applicator complete all as specified and directed. 76 M&L for preparation of new plaster surface of walls surfaces and applying two or more coats of acrylic smooth exterior paint of required shade new work (two or more coats applied @ 1.67 Ltr/10 Sqm and including priming coat of exterior primer applied @ 2.20 Kg/10 Sqm,applying by bump roller applicator complete all as specified and directed. 77 Dismantlingwall and ceiling boarding with frame work of any description, fixed in any position with nails/screwscomplete all as specified and directed. 78 S & F for providing aluminium snap gridframe work for false ceiling system withsize 605 mm x 605 mm, consisting of mainrunner of size 36.5 mm x25 mm x 1.4 mm (weight not less than @ 0.24 Kg/Rm) andcross Tee of size23.5 mm x 36.4 mmx 1.4 mm (weight not less than @ 0.191 Kg/Rm). The snap grid shall be supported at end all along the wall with aluminium anodised angle of size 40 mm X 25 mm X 2 mm (weight not less than @ 0.36 Kg/Rm).The snap grid shall be fixed to ceilingsupporting hangers consisting of 2 mm diamild steel wire /GIwire, J-bolts ,nuts and washers as per manufacturers instructions and complete all as specified and directed by Engr-in-Charge. 79 M & L for 4.0mmthick Non asbestos fibre cement building boardsfixed in ceiling flat or slopingfixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and directed by Engr-in-Charge. 80 S & F in repair 600mm X 450 mm bevelled edge looking mirror of selected quality glass mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with CP brass screw and cup washers complete all as specified and directed. 81 Dismantling old asbestos cement (corrugated, semicorrugated,etc.) sheets in roof coveringsincluding ridge complete all as specified & directed. 82 S & F fo Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified & directed. 83 S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed. 84 Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc.complete all as specified & directed. 85 Taking down ceiling fan/exhaust fanof any sweep after disconnecting all necessaryelectrical connections from ceiling roseto fan, fan blades and deposit to MES store yard of AGE E/M Ramgarh complete all as specified and directed. 86 M&L for point wiring for one light/fan/exhaust fan point/ wall fan pointcontrolled by one 5 Amp switch with using 1100 volt FRLSH PVC insulated PVC unsheathed electric cable conforming to IS:694, 1100V grade AC, single core having multi stranded copper conductor of size 1.5 Sq.mm nominal cross sectional area for phase & neutralandincluding non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system & 1.5 Sqmm green PVC insulated unsheathed multistranded copper conductor as a earth wire connected to earth dolly by providing lugs including sunken type anodized pressed steelsheet terminal box (normal & modular type) made out of 1.6mm thick of suitable size, for mounting fittings/junction boxes including PVC board with bakelite sheet 2.8 mm thick laminatedcover make sheet for housing/ fixingswitches etc.,includingcutting holes for switches,sockets,regulators etc as per requirement including fixing with machine screw,washer etccomplete all as specified and directed.Note: Proper colour coding to be adopted. 87 All as per item no 86 above but one 5 Amps socket outlet on same board complete all as specified and directed 88 All as per item no 86 above but one 5 Amps socket outlet on independent board complete all as specified and directed 89 M & L for point wiring for 15 Amppower point controlled by one 15 Amp with using with FRLSH PVCinsulated PVC unsheathed electric cable conforming to IS:694, 1100V grade AC, single core having multi stranded copper conductor of size 2.5 Sq.mm nominal cross sectional area for phase & neutralandincluding non metallic rigid PVC conduit ISI marked medium grade not less than 25 mm dia with all conduit accessories in concealed wiring system & 2.5 Sqmm green PVC insulated unsheathed multistranded copper conductor as a earth wire connected to earth dolly by providing lugs including sunken type anodized pressed steelsheet terminal box (normal & modular type) made out of 1.6mm thick of suitable size, for mounting fittings/junction boxes including PVC board with bakelite sheet 2.8 mm thick laminatedcover make sheet for housing/ fixingswitches etc.,includingcutting holes for switches,sockets,regulators etc as per requirement includingfixing with machine screw,washer etccomplete all as specified and directed. 90 S & F switch piano flush button single pole one way 5 Amp, complete all as specified and as directed. 91 S & F Switch socket combination 2 in 1, 3 pin, 5 and 15Amp flush type, universal, complete all as specified & as directed 92 S & F Switch socket combination 2 in 1, 3 pin, 5Amp flush type, universal, complete all as specified & as directed 93 S & Fsocket 2 in 1, 3 pin, 5 Amp flush type, universal, complete all as specified & as directed 94 S&F fan regulator electronic, step type hum free, socket type, suitable for ceiling fans of any capacity, pre wired 230 volts AC 50 HZ supply 100/120 Watt on the existing phenoliv laminated sheet etc.,complete all as specified & as directed 95 S & F ceiling rose three terminals PVC/ Polycarbonate, isolated body, ISI markedcomplete all as specified & as directed 96 M & L for point wiring in PVC concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 20 mm dia with multi stranded FRLSH copper conductor cable of size 4.0 Sqmm including clamps, screws guttier/plug etc PVC unsheathed cable into and sunken anodized pressed steel sheet boxes made out of not less than 1.6 mm thick sheet with bakelite sheet 2.8 mm thick and PVC insulated FRLSH cable of size 4.0 Sqmm as earth continuity conductor for AC point controlled by metal clad socket complet all as specified and directed by Engineer-in-Charge. 97 S & Fin repair Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp breaking capacity 10 KA ,C series complete all as specified and as directed. 98 S & F LED light fitting 1 x 20watt , 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting, complete all as specified and as directed by Engr-in-Charge. 99 S&F LED light fitting with high out put diffuser 2 feet, 10 watt 220 V AC waith driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge 100 S & F LED light fitting 1 x 9W/1x10watt ,bulkhead luminaires inlcuding LED light driver, holder connecting up with three core flexible copper conductor cable of suitable sizecomplete all as specified and as directed. 101 S&F new generation energy saving and environmental friendly long life versatile pressure dec cost aluminium IP 65/66 protection with fish power LED bldg security light of capacity 25/35W 230volt AC outdoor type with pre wired and necessary mounting arrangements ans provision of 2.5 sqmm three core flexible copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as specified and directed. 102 S&F Lamp holder, PVC/Polycarbonate type with back plate having matching colour to holder suitable for angle/batten fittings (ISI marked) complete all as specified and directed. 103 S &F LED bulb of capacity 9 watts lumen out put (950 lm) length 113 mmand 60 mm dia, base cap B22, 3 star, (ISI marked) complete with all accessories base (ISI marked) all as specified & directed by Engineer-in-Charge. 104 Labour only for refixing the ceiling fan/Exhaust fan obtained from item No. 85 above with replacement of unserviceable 3 core PVC insulated PVC sheathed 3 core multistranded copper conductor cable of size 23/0.193 from ceiling rose to fan terminal including over hauling the fan, painting of ceiling fans/ exhaust fans complete with two coats of synthetic enamel paint by spraying including filling cavities with filler after cleaining all dust etc and writing the MES Number with synthetic enamel paint complete all as specified and directed. 105 S & F of exhaust fan electric single phase, AS 240 Volts, 50 Hz copper winding, 450mm sweep, 1200RPM made of sturdy Engineering plastic body complete with louvers and connecting with flexible PVC insulated multi stranded flexible copper conductor wire with flexible pipe of required size from ceiling rose including cutting of wall and finishing of plaster complete all as specified and directed. 106 S&F in repair for distribution board (DB) made out of steel sheet metal enclosure (CRCA sheet) dust and vermin proof Triple pole and neutral(TPN) 6 way IP 43 (double door) with 200 Amps rated copper bus bar neutral bar ,earth bar 415 Volts ,flush to wall including taking down carefully existing unserveciable /old main switches, DBS along with MCBs complete all as specified and directed. 107 S & F 415V 10KA B curve miniature circuit breaker (MCB) of TPN/FP 40 amp to 100 amp and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed. 108 S & F in repair sheet metal enclosurespowder coated for DBs when MCBs to used singlepole and neutral (SPN) double door 240 volts, 8 way with fixed on wall with suitable amp bus bar and neutral link (ISI marked) EARTH BAR & DIN RAIL confirm to IS:13032-1991 DB including taking down carefully existing unserveciable /old main switches, DBS along with MCBs complete all as specified and directed. 109 S & F amp rating 240V, 10 kA B Curve miniature circuit breaker (MCB) of single poles and neutral and current carrying capacity 32 Amp in the MCB DB complete with connection testing and commissioningcomplete all as specified and as directed. 110 Supply and fixing 240V, 10 KA B curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 AMP to 32 AMP, in the MCB DB Complete with connection testing and commissioning. 111 M & LSub main wiring with two runs ofsingle core 6.0 Sqmm PVC insulated FRLSH multistanderd copper conductor cable and one run of 6.0 SqmmPVC insulated unsheathedFRLSH multi stranded copper conductor cablefor earth wire drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 25 mm dia/appropriate dia with accessories & fittings complete and making good disturbed surface wall including taking down existing sub main wiring complete all as specified and as directed. Note : - Tworuns of 6.0 Sqmm cable andone run of earth wire 6.0 sqmm& conduit shall be measured as one unit length and extra length of cable required for connection to MCBs shall be deemed to be include in unit rate quoted by bidder. 112 M&L for Earthing complete for poles/DBs with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in theground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below normal ground level connected to galvanized iron wire 4mm diaas earth leadby means of bolts, nuts and washers of GIup to test point,GI tubing20mm bore light grade protection pipe, GI watering pipe 20mm bore medium grade with funnel & wire mesh, charcoal & salt, 40 mm thick pre-cast RCC cover (1:2:4) type B-1(using 20 mm graded crushed stone aggregate )reinforced with 8mm dia TMT bar @ 75mm c/c both way with mild steelhandle 20mm dia round bar , plastering 15mm thick with CM (1:6:) internally and upto 150mm below ground level externally & angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-1(using 20 mm graded crushed stone aggregate ) (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m & returning filling) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I including making good disturbed surface of wall ,floors etc.including taking down/dismantling of existing earthing complete all as directed.Notes: -(i)Earth lead & protection pipes length upto & including 7.50 metre.(ii)Earth filling shall be done by vegetable soil.(iii)Soil should be free from stone, boulders, aggregate, gravels etc.(iv) Rate quoted deemed to be included excavation and earth work in any type of soil with PCC type C1 in pit PCC cover & other arrangement complete all as specified and directed. 113 S&F in repair down rod fabricated out of 15mm dia heavy grade mild steel conduit not less than length of 1250 mm mild steel hanging clamps of suitable/appropriatesize & shape for down rod of with rubber reel, nut ,bolts with washer and including spliting pin suitable for 1200 mm/1400 mm sweepof ceiling fans duly painted with two coat of synthetic enamel White paint complete all as specified and directed. 114 Supply, laying ,jointing ,testing and commissining LT cable, XLPE Insulated ,armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sq.mm. 3.5 core including taking down of existing cable complete all as specified & directed. Note:- 1. Excavation & earthwork shall be measured & paid under respective item.(2) All Necessary T & P required shall be arranged by the Contractor. 115 M & L for laying GI tubing light grade 50mm dia with all fittings for cable protection including GI clamps nut bolts and washer etc all as specified and directed. 116 Excavation in trenches in any type of soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width or not exceeding 10 Sqm on plan and getting out soil including forming bottom surface to required slope/gradient forlaying cables/pipes, foundations, laying of cable, shafts, well, cesspits, manholes etc. complete all as specified and directed. 117 M&Lfor Returning, filling in including spreading, leveling, watering and well ramming in layers ofnot exceeding 25 cm thickafter the cables & pipes etc. are laid, jointed & testedand foundations complete all as specified and directed by Engineer-in-Charge. 118 Removal of surplus excavated spoilnot exceeding 50 Mtr distance and depositing where directed by Engineer-in-Charge at a level not exceeding 1.5 m above the starting point complete all as specified. 119 M&L sand filling in cable trenches for cable protection for clean dry sand unwashed including gently punning in a layer of 15 cm and 8 cm (total 23 cm) inthickness all across the laid portion of LT cable in trenches complete all as specified and directed. (Note:-Punned thickness shall only be considered for payment) 120 Supplying & Laying factory made un-reinforced pre-cast flat concrete cable protection cover of class LV, type- I, size 250 mm x 150mm x 40mm,complete all as specified and directed by the Engineer-in-Charge. 121 M&L for Boring ofhole under road, pavement, hard standing by using trenchless technique using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure complete all as specified and as directed by Engineer-in-Charge.Note :(i)Pipes shall be laid minimum 2.00 mtr below/under existing road surfaces/ apron /floors etc.(ii) T&P requird for road boring to be provided by the contractor at site own cost and no any claim enterained on this accont on later stage.
