Tender For Spl Repair To Bldg No P-67, P-533 And P-263 Of Various Units At Army Area Under Ge Army No 2 Jodhpur; 1 Demolition of cement concrete of any description and in any position not otherwise specifically provided for (such as copings, bands of any type, roof padding, kerbs, sunken etc;overall thicknessand removing the dust debris etc to a distance not exc 250 meter from site and disposing the same complete all as specified and as directed by Engineer incharge. 2 M&L for plain cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregates as over roof for making good depression/ undulation to make the existing roof surfaces as filling in depression of roof slab/ floor padding/ roof kerbs rounded or chamfered on edges etc complete all as specified and as directed.(Note WPC will be paid extra of respective item of schedule) 3 M&L for rendering 15 mm thick in CM 1:4 using 100% coarse sand on roof surface with Liquid water proofing compound 3% by weight of cement provided as floating / setting coat of cement complete all as specified and directed. Note : The plaster shall be provided when the concrete is green and plaster surfaces shall be steel toweled to get a smooth surface usining extra cement. Water proofing compound shall be measured and paid separately under respective item(Note WPC will be paid extra of respective item of schedule) 4 M&L providing and applying roof treatment as following stage:-(i)Apply 1st coat of PU coating ( Shaliurethane LHM @ 650gm/Sqm or equivalentby brush/roller/spray. Spread non-woven geo-textile or glass fiber tissue of 45 GDM with overlaps of 50 mm in both directions when the surface is still tacky, this is optional,to be assessed as per site requirements to achieve higher mechanical properties.(ii) Allow 1st coat to dry for 10-12 Hrs.(iii) (Apply 2nd coat of PU membrane (ShaliUrethane LHM @ 650gm/sqm or equivalent)as per manufacturs instructions. Extend waterproofing treatment up to 200 mm and terminate into groov on the parapet wall.(iv) Protect the applied liquid membrane by sprinkling sand @ 200gm/Sqm over the final coating when the surface is still tacky to facilitate plastering, and including 25 mm thickplastering in CM 1:3 with admixture and WPC.Note No-1:- treatment shall be done though authorisedrepresentative of manufactures instructions. 5 M&L for plain cement concrete 1:3:6 type C-1,using 20mm graded stone aggregates as in coping to parapet walls including necessary formwork complete all as specified and as directed. 6 Supply only integral water proofing liquid ISI marked Make: Pidiproof LW 7 Demolition of cement concrete (unreinforced) in ground floor not exceeding 15cm thickness belowor above ground level including floor finishes and removing debris from the site all as specified and as directed. 8 Dismantling glazed tiles/ kota stone/ terrazzo tiles any type as in dado/ skirting etc; including cement mortar bedding ( but not backing ) complete all as specified. 9 M&L for non skid ceramic coloured tiles of approved shade and pattern, of size 400x400mm sqm laid in floor, set and jointe (square/ rectangular) in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed. 10 M&L for glazed ceramic coloured tiles of approved shade and pattern of size 300x600mm 7 to 8mm thick or any other nearer size as approved by Engineer incharge in vertical surface set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 as in backing coat of tiles complete all as specified and as directed. 11 M&L for Vitrified 10 mm thick double charged (square/ rectangular) as in floors, size 600x1200mm set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed bedding layers in CM 1:4 complete all as specified and as directed. 12 M&L for Vitrified 10 mm thick double charged (square/ rectangular) as in skirting / dado, Cut out of ceramictiles of size exceeding 0.11 sqm but not exceeding 0.36 sqm, (Matching with floor tile of the same room) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed. 13 M&L for 20mm thick granite (colour as approved) work (table rubbed and polished) in steps, shelves, jambs, pillars, window-cills, cooking platforms (vertical/ horizontal) and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 10mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed. 14 M&L for machine cut kota stone slab flooring 20-25 thick over cement screed base laid and jointed with greycement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed. 15 M&L for mirror polished machine cut Kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick rendering in CM 1:4 and jointed complete all as specified and as directed. 16 M&L 75 mm thick cement concrete type D- 2, 1:4:8 (40mm graded aggregate) as in sub base complete all as specified. 17 M&L 25 mm thick cement concrete type B- 1, 1:2:4 (20mm graded aggregate) as in levelling course/undulation of floor complete all as specified. 18 M&L for Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in cement mortar 1:3 or cement mortar 1:6 completecomplete all as specified and as directed. 19 Cement concrete (1:3:6) type C-2 using 20 mm graded stone aggregate as in plinth protection, 50 mm thick, surfaces finished even and fair to receive the stone patti etcincluding Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in cementmortar 1:3complete complete all as specified. 20 Dismantling of stone/ brick work masonry, built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stone work,serviceable stone aside for reuse and removing unserviceable material in low laying area complete all as specified and as directed. 21 M&L for squared rubble walling jodhpur type, brought upto course, well bonded bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed. 22 -ditto- all asperitem ser No 21 above but, except stone complete all as specified and as directed. 23 Extra over for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling,Jodhpur type, brought upto courses all as specified and as directed. 24 Taking down cement plaster, any description, on brick or stone walls etc, including raking out joints, hacking for key, scrubbing down with water etc and disposal of debris complete all as specified and as directed 25 M&L for rendering 15 mm thick in CM 1:6 over stone masonary, concrete surfaces, finished even and smooth (without using extra cement), all as specified and as directed. 26 M&L for 15 mm thick rendering on stone masonary wall surfaces in CM 1:4finished fair and even all as specified and as directed. 27 M&L for 10mm thick rendering in CM 1:3 on ceiling surfaces finished surfaces even and smooth without using extra cement complete all as specified and as directed. 28 Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixingor removal to Store (measured overall as fixed along the centre line over fittings and accessories)complete fitting all as specified. 29 S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified. 30 S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified. 31 S&F75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified. 32 S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified. 33 S & F PVC (SWR) bendsany radius 110mm dia. 34 S & F PVC (SWR) single TEE equal or unequa110mm dia. 35 S & F PVC (SWR) single TEE equal or unequa 75mm dia. 36 S & FPVC (SWR) bendsany radius 75mm dia. 37 S & F in repair 75mm diaPVC (SWR) multi floor trap with grating including jointing with solvent cement , complete all as specified and directed. 38 S&F 110 mm dia PVC (SWR) S trap complete all as specified. 39 S&F Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required:hooks (stay), heavy, for large gates; hook and pintle hinges:large hasps and staples; chains; hand made sliding bolts; clamps;hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified. 40 S&F in repair 40mm bore steel water tubing medium grade galvanised insertedat the end of lateral slope projecting at least 15cm beyond the outer most projected part of the building below the drain pipe up to two storey construction as spout for sunken complete all as specified. 41 Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm butnot exc 4.00 sqm each and removing from site or to store as directed by Engineer incharge. 42 Taking down chowkhats or frames with shutters (without taking off shutters from the frames) notexc 1.5 sqm each and removing from site or to store as directed by Engineer incharge. 43 S&F of pressed steel framed made out of 1.25mm thick MS sheet, of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed. 44 S&F of pressed steel framed made out of 1.25mm thick MS sheet, of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed. 45 M&L for cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats etc.,complete all as specified 46 S&F of factory made 35 mm thick plain framed, panelled shutters (two panel) with 2nd class hard wood rail and stylewith lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified. 47 S & F35mm Glazed and skeleton shutters, open rebated and preparedto receive glass,gauze, etc. divided into squares, with plain,chamfered or rounded,mitred and rebated sash bars,any numbers. fitted with cut and mitred beads for securing glass,etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats 48 M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stoneaggregate as in lintels upto 1.50 m clear span, cills , steps, seismic and other similar bands, copings, kneelars, apex stones, bed plates, bedblocks of hold fasts etc including necessary form work complete all as specified 49 S&F Powder Coating(minimum thicknessof powder coating 50 micron) of anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified 50 S&F Powder Coating(minimum thicknessof powder coating 50 micron) anodised aluminium door, window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified 51 S&F of Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. complete all as specified. 52 S&F of sheet glass ordinary quality 4 mm thick and glazing with oil putty or fixed with wooden beads or fixed with rubber gasket in squares any size of pane complete all as specified & as directed. 53 .-Ditto- all as per above item but 4mm thick frosted glass complete all as specified and directed. 54 S&F of galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified & as directed. 55 S&F in repairs galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified & as directed. 56 Taking out old serviceable glass of any description, from old wooden or metal frames, or stone, concrete or brick surrounds, any thickness or size; hacking out old putty or removing beads etc, including making good breakages in taking out and handling removing to store or stacking for reuse of any size. 57 Fixing only glass of any thickness to aluminium door/partioton Note Material reused obtain from taking down from item No-56 above. 58 Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads 59 S&F 4mm thickSheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete alla as specified. 60 S&F of factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing S&F. Make : Rajshree Doors or equivalent as approved by GE. 61 S&F of solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing. Make : Rajshree Doors or equivalent as approved by GE. 62 S&F of 100 mm size PVC/ Stainless Steel (as approved by Engineer incharge) butt hinges all as specified and directed. 63 S&F Aluminium handles, cast type,anodised, 150 mm long and fixed with steel screws complete all as specified. 64 S&F Aluminium anodised,barrel tower bolts of extruded section,150mm long and fixed complete all as specified. 65 S&F of 300 mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including bolts and nuts complete all as specified. 66 Taking down 15mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specified. 67 Taking down 20mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specified. 68 Taking down 25mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specified. 69 S&F of 15mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified. 70 S&F of 20mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified. 71 S&F of 25mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified. 72 S&F in repair vitreous china squatting pan, Orissa pattern, size 580x440mm white/ coloured with integral foot rests including flus pipe and connection to trap, and to flushing pipe, anti-syphonage pipe etc; complete all as specified. 73 S&F in repair PVC 10 ltr. Cap. valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc. all as specified. 74 S&F in repair vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing complete all as specified. 75 S&F in repair for Vitreous china urinal, half stall type, white, completeincluding providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60cm long brass screws, pointing around urinal back in cement , suitable PVC waste pipe with brass unions, including making all connections to existing connections,complete all as specified and as directed. 76 S&Fin repair PVC low density polythene pipe (LDPE) of pressure rating 6 Kg per Sq.cm, 450 mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repair complete all as specified. 77 Disconnecting existing PVC tank exc 500 Ltrs and not exc1000 Ltrs setting aside (or lowering if required) for repairs, cleaning, etc and hoisting if required reconnecting refixing in position complete all as specified and directed. 78 S&F in repair 1000 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I complete all as specified. 79 Supply and fixing in repair 5mm thick bevelled edge mirror of fancy type selected quality including making 4 to 8 x Nos holes and fixing with Stainless steel spacer /SS cup washerscomplete all as specified and as directed . 80 S&F in repair 15mm bore chromium plated bib taps, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified. 81 S&F in repair for pillar tap, brass, 15mm dia, with capston heads, chromium plated,fancy type screwed down, high pressure, with or without lettered hot or cold, with long shank, screwed shanks and fly nuts, screwed for iron pipes or for wash hand basin all as specified and as directed. 82 S&F in repair 15mm bore stop valve/ angle stop cock chromium plated,fancy type cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe with long shank and cup complete all as specified. 83 S&F in repair 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified. 84 S&F in repair chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union suitable for 15mm bore pipe etc; complete all as specified. 85 S & F in repair 15mm bore concealedstop valves brass chromium plated long shank, with capstan head and cup screwed both ends for iron pipe or for union complete all as specified and directed. 86 S&F in repair CP towel rail 450mm long fixed with and including CP brass screws and wooden/ plastic cleats complete all as specified. 87 S&F in repair CP greating doom 100mm dia complete all as specified. 88 S&F 25mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight for 25mm ball valves-455gms) fixed in repairs i.e., incl taking down and removal of old unserviceable float valves complete all as specified and as directed. 89 Preparing new or previously untreated surfaces of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed. 90 Preparing new plastered surfaces and M&L for applying concrete primer and /or cement base putty as required incl preparing the surfaces smooth by rubbing and / or sandpapering and M&L two coats of cement base paint on new plastered surfaces all as directed by Engr in charge. 91 Preparation of newplastered surfaces of ceiling etc. & applying three coats of limewhite wash on ceilingcomplete all as specified. 92 Preparing new plastered surfaces and M&L for applying chalk whitening/ concrete primer and /or cement base putty as required incl preparing the surfaces smooth by rubbing and / or sandpapering and M&L two coats of Distemper oil Emulsion on new plastered surfaces all as directed by Engr in charge. 93 Preparing oldsurfacesincl brooming surfaces, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil or greasy spots incl washing rubbing down and stopping of distempered and painted surfaces and M&L forapplying one coat of cement base paint on walls etc.,complete all as specified and as directed. 94 Preparation of old decorated plastered surfaces of walls etc. & applying one coat of white wash complete all as specified. 95 Preparation of old decorated plastered surfaces of ceilingetc. & applying one coat of white wash on ceilingcomplete all as specified. 96 S&Fwindows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM) and Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52x 25mm. Outer frame & mullion sections to have rebate for glazed shutters. Fly mesh with 20 mm GI flat beading for provision of guard bars/ grills. Fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stainless steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter with 0.36mm dia of wire and 1.40mm aperture. Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 12mm square guard bars with 110mm spacing c/c (Horizontal bay) to be welded on FI 20x6mm alaround except runner portion complete all as specified and directed.(TD No-CEJZ/TD/89/2017 of Sheet 1/1 & 1/2)(Note -glass,wire mesh and guard bar includednothing paid to extra on this account of respective item of schedule) 97 Preparing new or previously untreated surfaces of steel or iron work of any description and girth over 10cmand applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified andas directed by Engineer incharge. 98 Preparing oldsurfaces of steel or iron work of any description and girth over 10cmand applying two coats of synthetic enamel paint complete all as specified andas directed by Engineer incharge. 99 S&F in repair stainless steel 25mm dia pipe as in curtain rods including brackets with fancy end knob wall to wall andcomplete, all as specified and directed. 100 M&L for carrying out repair dammagedRCC projections,chajja facia, roof projection facia, etc in the following stages -(i) Demolition of existings dammaged RCC projection,chajja facia, roof projection faciaand similar suspended work and (reinforcement cut as required to facilitate demolition).(ii) Preparation of existing demolised portion by scrapping, cutting, chiseling, derusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC and providing cement concrete (1:1.5:3) using 12.5 mm graded crushed stone aggregate including necessary form work and reinforced with low carbon annealed wire in hexagonal shape 1.0mm diametre chicken wire mesh of size 25mm complete.(iii) Providing and applying approved chemical rust remover with paint brush on corroded rebar and removing loose particles after 24 hours of its application and washed with sufficient quantity of water to make rebar free from corrosion.(iv) Providing & fixing new reinforcement of various diameters as required at site in the form of mild steel and /or steel confirming to IS and lapping, welding, anchoring suitable to the old reinforcement including cutting, bending with all tools & tackles etc;(v)Applying 1stcoat rendering of 10mm thickin CM (1:3)over demolished concrete facia/projection surfaces and allow to dry 6-8 Hrs and cured with gunny jute bag. (vi) Applying finished coat of 10mm thick rendering in CM 1:4 using 100% coarse sand over 1st coat rendered surfaces and finished surface even and smooth with using extra cement and mixed with 3% integral water proofing compound and making drip mouldings as reqiured and cured with jute gunny bag for 7 days,complete all asdirected by Engr-in-Charge.(vii) Preparation of surface and applying two coats of weather coat paint over a coat of exterior wall care puttyto match existing surfaces complete all as specified and as directed.Note:- (Reinforcement shall be paid in respective item of Schedule A)The rates quoted by the bidders/Contractor shall include thefollowing:-(a) Work carried out up to 12 Mtr in height.(b) Use of Scaffolding, trestles, ladders, cradles etc necessary for execution of work andall protective measures responsibilty.(c) Removal of excavated material n exc. 50m and depositing where directed by Engr-in Charge. 101 S & F in repairs E board Everest make 600x600x4mm thick white prelaminated sett embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24 x 32 x 300mm and spaced at 1200mm centers securely fixed to the structural soffts by approved hangers at 1200mm, maximum centrers.Hangers of GI wire 4 mm dia to be fixed by approved rawl plug, level and jumper and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall, Flush fitting of 1200mm long cross tee (with double stiching) to be interlocked between main runners at 600mm centre to from 1200 x 600 mm modules cross tee longer than 600mm to be supported independently. 600x600mm dodules to be formed by fitting 600mm long cross tee centrally between the 1200mm cross Tee, perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacturers instructions complete all as specified.and directed. 102 S & Fin repair 18mm thick factory made 100% solid WPC flush shutter (for cupboard, wardrobe ,etc) made from co-extruded three layer rigid foam sheet Single extruded) with 0.8 to 1mm thick outer layer having density not less than 1400kg/cum and density of center core not less than 600kg/cum, with prelamination on both front and back side manufactured by and ISO 9001/2015 certified company complete all as specified and directed. 103 S & F Continuous (piano) hinges,mild steel, bright finish or electro galvanised width of flaps (when open in 30 MM) 104 S&F 100mm aluminium handles, cast type, anodised complete. 105 S & F magnet catcher heavy duty for cupboard door shutter complete all as specified and directed. 106 Taking down anodised aluminium door shutters, side hung or fixed type exc 1.5 sqm and n. exc 4 sqm and refixing in same opening after repairing including necessary jointing cleats, glazing clips, rubber packing, screws etc and with existing anodised aluminium snap beading, screws anodised aluminium fittings such as hinges type B-21, 125mm long anodised section complete including overhauling of floor door spring hydaulically regulated complete all as specified and directed. 107 Taking down and refixing of aluminiun window shutter (sliding/opanable) in the same opening after repair/overhaulingof aluminium shutter complete incl all necessary spares all as specified and directed. 108 Supply and fixing in repair Aluminium (Die cast) body Door closer hydraulically regulated designation No 3 universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed 109 Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete 110 M&L for carrying out water proofing treatment for roofs in the following stages:-(i) Rendering 10mmthick plaster in CM (1:4) mixed with integral water proofing liquid all as per manufacturers instructionsNote : (i) WPC shell be measured and paid separately under respective item of schedule.(ii) The plaster shall be provided when the concrete is green and plaster surfaces shall be steel toweled to get a smooth surface usining extra cement.(ii)Apply 1st coat of PU coating ( Shaliurethane LHM @ 650gm/Sqm or equivalentby brush/roller/spray. Spread non-woven geo-textile or glass fiber tissue of 45 GDM with overlaps of 50 mm in both directions when the surface is still tacky, this is optional,to be assessed as per site requirements to achieve higher mechanical properties.(iii) Allow 1st coat to dry for 10-12 Hrs.(iv) (Apply 2nd coat of PU membrane (ShaliUrethane LHM @ 650gm/sqm or equivalent)as per manufacturs instructions. Extend waterproofing treatment up to 200 mm and terminate into groov on the parapet wall.(iv) Protect the applied liquid membrane by sprinkling sand @ 200gm/Sqm over the final coating when the surface is still tacky to facilitate plastering, and 25 mm plaster admixed with WPC. 111 M&L for non skid ceramic coloured tiles of approved shade and pattern, 7 to 8 mm thick , area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm laid in floor, set and jointe (square/ rectangular) in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed. 112 M&L for glazed ceramic coloured tiles of approved shade and pattern of size 350x 250x7mm/ 450X350X7mm/ 300X450X7 to 8mm thick or any other nearer size as approved in vertical surface set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 as in backing coat of tiles complete all as specified and as directed. 113 Dismanteling Stone slabs and tiles of any description or thickness in floors, aprons etc.laid beded and pointed in any mortar complete all as specified. 114 M&L for Mirror polishing on marble/ granite/Kota stone/ stone work where everrequired to give high gloss finish including riser of steps, skirting, dado complete all as specified and as directed. 115 M&L for providing precast cement concretetype C-1, 1:3:6 (20mm graded aggregate as with block masonary solid blocks exc 10cm in width and setting in cement mortar 1:6 all as specified and as directed. 116 S&F low carbon annealed wire in hexagonal shape 1.0mm diameter chicken wire mesh of size 25mm (distance between the faces of the hexagon), durable twisted woven mesh for mounting on curved and angled surfaces including 15cm lap at junctionfixed with nails and properly stapled complete all as specified and as directed. 117 Dismantling cast iron work of any description and in any position complete all as specified. 118 S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc; complete all as specified. 119 S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, fixed to walls etc; complete all as specified. 120 S&F 75mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc; complete all as specified. 121 S&F 75mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, fixed to walls etc; complete all as specified. 122 S&F 100mm bore pipe cast iron P or S trap, complete all as specified. 123 M&L cast iron up to 150mm bore fittings of Bends (any type, radious and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces, single branch, Y junctions, double branch, cross (all sockets or socket and spigot) collars, caps and plugs etc; complete all as specified. 124 M&L 100mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) apply as per manufacturing instructions, complete all as specified. 125 M&L 75mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) apply as per manufacturing instructions, complete all as specified. 126 S&F for 100mm bore pipes stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall etc; complete all as specified. 127 S&F for 75mm bore pipes stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall etc; complete all as specified. 128 Pressed steel framed made out of 1.25mm thick MS sheet, of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed. 129 M&L for fabrication ofaluminium powder coated ventilators (with louvered) fabricated with anodized aluminium rectangular section in frame & with deco grill of approved design & stainless steel wire cloth on the outer side of frame & trade pattern louvers with suitable mechanism for tilting /opening closing etc all as per sample kept in GE office & fixed in position complete all as directed.(Note-1.Glazed shutters float glass thickness not less than 5.00 mm and wire mesh shutter with Stainless steel (SS-304) wire mesh 0.36 mm dia with aparture 1.4mm shall also be deemed included in quoted rates andNo extra payment will be made separalely(Note : Glass pane in louvers & stainless steel wire cloth shall be measured & paid separately) AS per Drg No- CEJZ/TD/89/2017. 130 S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & as directed. 131 S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified. 132 S&F mild steel door handles, stove enameled black, 150 mm long and fixed with steel screws complete all as specified. 133 Mild steel barrel tower bolts, stove enameled black, with bright bolt, 150 mm long and fixed with steel screws complete all as specified. 134 S&F 300 mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including bolts and nuts complete all as specified. 135 S&F of mild steel single action helical hinges 150-200mm long, suitable for 1000-1250mm wide wooden door fixed with steel chowakats etc; complete all as specified. complete all as specified & as directed. 136 S&F in repair 500 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I complete all as specified. 137 S&Fin repair glass self assembly, fancy type,made of 6 to 7mm thick sheet toughened glass of size 250x250mm,fixed with CP brackets,complete,all as specified and directed. Make: Jaquar range OR equivalent 138 S&F in repair PVC SWR type B socketed rain water pipes 110mm dia conforming to IS: 4985/ IS: 13592 complete all as specified and as directed. 139 S&F in repair PVC SWR bend/shoe of PVC 110mm dia suitable for 110 mm bore / dia PVC SWR rain water pipes complete all as specified and as directed. 140 M&L Mild steel bars 6mm to 8 mm dia (TMT) bar, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 141 Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces 142 Preparation of newplastered surfaces of ceiling etc. & applying two coats of oil bound distemer on ceilingcomplete all as specified. 143 Preparing oldplastered surfaces brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots incl washing , rubbing down and stopping of distempered or painted surfaces and M&L for applying onecoat of distemper oil emulsion on old plastered/ unplastered surfaces of walls complete all as specified and directed by Engr-in-Charge. 144 Preparation of old decorated plastered/ unplastered surfaces of ceilingetc. & applying one coat of distemper on ceilingcomplete all as specified. 145 Demolition of cement concrete(unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified. 146 M&L Hardcore of broken stone boulders guage exc 63mm but n exc. 100 mm, deposited,spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface 147 M&L for 100 mm thickPCC 1:4:8 type D2(40mm graded stone aggregate) as in sub base,foundations filling and mass concrete 148 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curveshall not to more than 5 mm), including making drainage opening whereverrequired complete. 149 M&L Cement concrete type B-0,1:2:4 (12.50 mm graded stone aggregate) as in kerbs or mud stops,rounded or chamfered on edges as specified and directed. 150 M&L Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath,parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand,compacting and proper embedding/ layingof inter locking paver blocks into the sand bedding layer through vibratorycompaction by using plate vibrator, filling the joints with fine sand and cutting ofpaver block as per required size and pattern, finishing and sweeping extra sand; complete. 151 Taking down carefully aluminum/copper point wiring (light/fan/ socket/ power) complete including fittings such as switch, socket, ceiling roses light fittings etc andand making good disturbed surface of wall all as specified and directed by Engineer-in-Charge. 152 M&L for modular point wiring One light/Fan/bell point /Exhaust fan controlled by one switch one way complete with 1.5 Sq mm single core PVC insulated but unsheathed multistranded copper conductor FR-LSH cable (RYBN) 1100 volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit with wall thickness not less than 1.8 mm including conduit accessories like bends, tees junction boxes, etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sq mm, single core,PVC insulated but unsheathed multi stranded copper conductor FR-LSH cable (Green) 1100 Volts grade as earth continuity wire connected to earth dollyand including modular sunken galvanized terminal boxes of same make of switch/ socket/ regulator withsleek and curvy cover plates, for mounting ofmodularswitches, sockets, fan regulators complete all as specified and as directed. 153 One socket out let 5 Amps 3 Pin on same board with other switch 154 One socket out let 5 Amps 3 pin on independent board 155 All as per item No 2 here in before but with single core multistranded cable of size2.5 Sqmm for one 15 Amps socket outlet on independent board and multistanded insulated copper earth continuity conductor of size 2.5 Sq mm all as specified and directed 156 Supply and fixing Modular switch15/16 Ampsone way 240 V. 157 Supply and fixingModular socket out let 2 in 1 multi pin 5 Amps flush type universal. 158 Supply and fixingModular switch5 Amps one way. 159 Supply and fixing Modular socket outlet in repair 2 in 1, 3 pin, 5 and 15 Amps socket outlet 240 volts SP 160 Supply and fixing modular Fan step regulator, 120W - 2 module 161 Supply and fixing Ceiling rose on PVC FRLS board size 65 X 50 mmthree terminal Complete. 162 S&F LED luminaire 600x600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for false ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed 163 Supply and fixing in replacement LED light fitting mirror type with ligh out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete 164 Supply and fixing in replacementLamp Holder, PVC FRLS/polycarbonate type with back plate suitable for batten fittings. 165 Supply and fixing LED lights fitting 1x 18W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete 166 Supply and fixingin replacement LED Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66/67 protection complete 167 S&F sheet metal enclosure SPN 240 Volts having 2 pin and earth plug and socket complete with one single pole MCB 20 Amps all as specified 168 M&L for concealed sub main wiring with 2 single core 6 Sqmm copper conductor (Multistandered) in PVC FRLS conduit of suitable size as required,including 4.0 Sqmm copper conductor as earth continuity all as directed. 169 Taking down old wiring circuit/submain wiring and supply & fixing for concealed/conduit or as per existing sub main wiring with 2 single core 4 Sqmm copper conductor (Multistandered) in PVC FRLS conduit of suitable size as required,including 4.0 Sqmm copper conductor as earth continuity complete all as specified and as directed. 170 S&F in replacement of Distribution Board, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 12 way (Concealed flush to wall), 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed.Note : 1.Blank plates will be included on the quoted rates.2. All wires to be properly connected with copper lugs.3.MCB will be measured and paid separately. 171 S&F in replacement of TPN DB, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, TPN 4 way (Concealed flush to wall), 415 volts with bus bar rating 250 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed.Note : 1.Blank plates will be included on the quoted rates.2. All wires to be properly connected with copper lugs.3.MCB will be measured and paid separately. 172 Supply and fixingin replacement 240V, 10 KA B curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified. 173 Supply and fixingin replacement MCB SPN, 63 Amp, C Curve 240 volts.in the MCB DB Complete with connection testing and commissioning complete all as specified. 174 Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 200 mm 175 M&L for earthing with galvanized steel earth plate electrode of size 600 x 600 x 6 mm buried directly in ground earth pit not less than 2.25 mtr below of normal ground level with top edge of earth plate should not less than 1.5 mtr below normal ground level and connected to galvanized iron earth lead wire of size 4 mm dia by means of bolts, nuts, washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part I connecting to earthing test point on completion with and including 15 mm bore GI light grade protection pipe (7.5 mtr long) for earth lead GI lead wire 4mm dia (7.5 mtr long), PCC pit with cover in PCC 1:2:4 type B-1 reinforced with 8 mm dia tor bars @ 80mm C/C, 20mm dia medium grade watering pipe with funnel, wire mesh, common salt, charcoal, necessary excavation and earth work, complete all as specified and directed. 176 Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5core 177 Excavation in trenches n exc 1.5 mtr wide, n exc 1.5 mtr in depth and n exc 10 sqm on plainand getting out in hard/dense soil for cable, pipe etc. all as specified and as directed by the Engr-in-charge . 178 Returning, filling in, incl. spreading, leveling, watering and well ramming in layers n exc 25 cm deep in soft/loose soil complete all as specified and as directed by the Engr-in-charge 179 Removing surplusexcavated Soil to a distancenot exc 50 manddepositing where directedat a level n.exc. 1.5 m above the starting point complete all as specified and directed. 180 Supplying and laying (length perpendicular to axis of cable) un-reinforced precast concrete cable cover,ISI marked ,class LT, type 1, size 250mm x 150mm x 40mmduly embossed with LT Cable 1100 Volts, cable size inSQMM allas specified and as directed. 181 M & L for fine dry river sand cushioning by laying 8cm thick layer below the cable for making soft bed and 15 cm above the cable and then punning down to its consolidated thickness of 18cm after the cable is laid all as specified in SSR Part I and as directed. 182 Supply and lay 50 mm bore galvanised steel tubing Light grade with all fittings and fixtures laid in trench or ceiling or laying in floors complete all as directed.
