Tender For Repair / Maintenance For Improvement Of Power House, Mes Installation And B/R Related Works, Indoor Panels, Earthing, Bus Bar Panels And Other Misc Work Under Ge (East) Agra.; 1.00 Taking down of old roof treatment of any description including mud phushka, concrete padding, tiles, cement plaster from roof surfaces etc including cleaning ,brushing and watering to joints and grooves and throwing the same to a distance exc. 250 mtr and not exc 500 mtr from the roof of height 3 to 9 mtr etc complete all as specified and directed. 2.00 M&L for Clean the concrete screed with high pressure water jet to remove dirt and loose particles. Brush apply a bond coat of Pidicrete URP mix in the ratio of 1:1 (URP 1: Cement 1) by volume to make it lump free slurry when applied on in the pre wet surface. Laid to fall roof screed in correct slope and gradient. Mix Pidicrete URP 10 % by weight of cement in concrete in ratio of 1(cement) :1.5 (sand) : 3(12.5 mm aggregate) & avg thickness of concrete should be 25 mm.Level the repair concrete and finish with trowel. Moist cure should be done for 7days. Air cure screed for 7days, before application of roof top coat coating system etc complete all as specified & directed. 3.00 M&L for Apply one coat of Cipoxy 16D primer in the ratio 1:1 spreading at the rate of 0.200 kg-0.250 kg /sqm in complete dry condition where moisture contain below 7% (should be checked with moisture meter)Allow the primer coat to dry for 6 to 8 hours. Apply 1st coat of Roofseal Classic without dilution spreading at the rate of 0.70/litre/Sq.mt/Coat until all surface is covered. Lay a 45 GSM Fibre glass mesh as a reinforcing material which is incorporated in the coating when the first coat is still in wet condition. Allow the first coat to dry for approximately 4 to 6 hours. Apply the second of chemical with the same application coverage, but in a direction perpendicular to that of the first and second coats. Allow each coat to air cure for a minimum of 4-6 hours after application. Check to see no void surface is left untreated / uncoated.Allow the system to air cure for 7 days minimum etc complete all as specified & directed. 4.00 Demolition of brick work or stone masonry including all quoins,arches,pillars etc built in CM complete all as specified & directed. 5.00 M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified & directed. 6.00 Taking down cement plaster on wall/ceiling/roof etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed 7.00 M&L for rendering 15 mm thick cement plaster in CM 1:4 on brick work / concrete surfaces and finishing the surfaces even and smooth without using extra cement etc all as specified & directed. 8.00 M&L for rendering 10 mm thick cement plaster in CM 1:3 on brick work / concrete surfaces of ceiling,chhajja etc finishing the surfaces even and smooth without using extra cement etc all as specified & directed. 9.00 M&L for rendering 12 mm thick cement plaster in CM 1:6 on brick work / concrete surfaces of walls & finishing the surfaces even and smooth without using extra cement etc all as specified & directed. 10.00 Material & labour for preparation of new plastered surfaces of ceiling and applying three coats of white wash to match the existing as required, complete all as specified & directed. 11.00 M&L for preparation of newly plastered surfaces of walls and applying three coat of white wash complete all as specified and directed. 12.00 M&L for two coats of OBD over a coat of average 2 mm thick wall putty on newly plastered surfaces complete all as specified and directed. 13.00 M & L for two coat of cement base paint over a coat of primer on new plastered surfaces of wall including preparation of surfaces complete all as specified and directed. 14.00 M&L for Preparing old plastered surfaces of walls by brooming down or by steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and applying one coats of oil bound distemper complete all as specified and directed. 15.00 Material and Labour for preparation of old plastered surfaces of ceiling etc by brooming down by steel wire brushing, scrapping down smoke Soot, moulds, moss and trading oil and greasy spots etc and apply one coat of white wash complete as specified and directed. 16.00 Material and Labour for preparation of old plastered surfaces of wall etc by brooming down by steel wire brushing, scrapping down smoke Soot, moulds, moss and trading oil and greasy spots etc and apply two coat of white wash complete as specified and directed. 17.00 M & L for one coat of cement base paint on old surfaces of wall including preparation of surfaces complete all as specified and directed. 18.00 M & L for single coat of apex paint of approved colour on surfaces of pillar/band etc width n exc 0.45 m including preparation of old surfaces complete all as specified and directed.. 19.00 M&L for 2 mm thick wall care putty on wall surface etc all as specified & directed. 20.00 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified & directed. 21.00 Dismantling of stone slab of any description or thickness in floor ,step, riser etc laid bedded and pointed all as specified & directed. 22.00 Demolition of concrete in any description and in any position (unreinforced) complete all as specified and directed. 23.00 M & L hard core of broken stone or boulder having gauge n exc 63mm, deposited, spread and levelled in layers n exc 15 cm thk, watered and rammed to a true surface, complete all as specified and as directed. 24.00 M&L for 75 mm thick Cement concrete type D-2 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing finishing surface even and rough using broomfinish complete all as specified and directed. 25.00 M&L 40 mm thick PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) with metalic floor hardner finish the surface even & smooth without using extra cement etc complete all as specified.Note:- Metalic floor hardner shall be measured & paid saperately. 26.00 Supply only for metallic floor hardener for PCC (1:2:4) etc complete all as specified & directed. 27.00 Material and labour plain cement concrete type B-0, 1:2:4 (12.50mm graded aggregate) 25mm thick as in sub floor, sub base, to receive tiles complete all as specified and directed 28.00 M&L for non skid ceramic coloured tiles (Premium quality) (squre/ rectangular) area of each tiles exc 0.11 sqm but n. exc 0.18 sqm in floors etc set and jointed in neat cement slurry over 15 mm thick screed bed in CM 1:6 and pointed in white or coloured cement to match the tiles etc complete all as specified and directed. 29.00 Ditto all as per item no. 28 but in skirting over 10 mm thick 1:4 CM Plaster etc complete all as specified & directed. 30.00 M&L for glazed ceramic coloured tiles of size 450x300x7mm thick fixed on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry over 10 mm thick 1:4 CM Plaster and pointed in white or coloured cement to match complete all as specified and drected. 31.00 M&L for 20-25 mm thick machine cut kota stone slab flooring over 20mm thick cement screed bed in CM 1:6 , laid and jointed with grey cement slurry mixed with pigment to match the shade of stone slab including cutting, grinding, rubbing and polishing complete all as specified & directed 32.00 M&L for 20-25 mm thick machine cut kota stone slab as in skirting, riser of step, dado and pillar etc over 15 mm thick cement plaster in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of stone slab including cutting, grinding, rubbing and polishing complete all as specified & directed. 33.00 Taking up or down 15 mm bore steel tubing including fittings and connections, including cleaning for rixing or removal from site complete all as specified and directed by the Engineer-in-charge. 34.00 S&F 15 mm bore Galvanized Steel tubes, medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. 35.00 Taking up or down 20 mm bore steel tubing/ PPR pipe including fitting and connections, including cleaning for Refixing or removal to store complete all as specified and directed. 36.00 S&F 20 mm bore Galvanized Steel tubes, medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. 37.00 S&F 500 litres capacity Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PVC float valve & nipple including dismantling of storage tank complete all as specified. 38.00 S&F in repairs 20 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified & directed. 39.00 S&F in repairs 600 x 450 mm bevelled edge mirror of selected quality glass 5 mm thick mounted on 6 mm thick commercial ply wood aluminium frame and fixed to wooden plugs with chromium plated brass screw and cup washers complete all as specified and directed. 40.00 S&F in repairs Vitreous China wash hand basin white flat back size 550x400mm including brackets ,32 mm CP waste coupling and 32 mm pvc heavy duty waste pipe 800 mm long etc complete all as specified and directed. 41.00 S&F Pillar taps long body cast copper alloy fancy type with capstan heads chromium plated scrwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for 15 mm dia iron pipe complete all as specified and directed. 42.00 S&F in repairs 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets & taking out of old unserviceable connections etc, connecting up new and making good disturbe portion complete all as specified and directed. 43.00 S & F in repairs PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed. 44.00 S&F in repairs 15 mm bore CP stop cock/angle cock, cast copper alloy fancy type, screwed down high pressure, screwed for iron pipe or for unions and fixed complete all as specified and directed. 45.00 Supply & fixing in repair CP tubular towel rail, 60 cm long, 20 mm bore, chromium plated complete all as specified & directed. 46.00 S & F in repairs Brass chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed. 47.00 S & F in repair CI floor trap, plain including jointing with solvent cement (Diameter of outlet 75mm), jointing to waste pipe and fixed in cement concrete 1:2: 4 (type B1) mixed with pedilite water proofing liquid @ 200ml in 50 kg cement, inlcuding taking out of old unserviceable connections etc, connecting up new and making good disturbe portion complete all as specified and directed. 48.00 Supply & fixing in repairs C.P. grating 100/125 mm dia with or without centre hole etc all as reqd at site complete all as directed. 49.00 S&F in repairs vitreous China squatting pan (Orissa pattern), white, of size 580x440mm white, with CI P or S trap, integral foot rests including flush pipe, trap, lime concrete bedding inlcuding taking out of old lime concrete bedding, unserviceable connections etc connecting up new and making good disturbe portion complete all as specified and directed. 50.00 S & F in repair of plastic WC seat cover and mild steel chromium plated or aluminised hinging device as etc complete all as specified and directed. 51.00 S & F in repairs health faucet for pedestal pattern WC incl flexible pipe and brass chromium plated nuts and bolts and water pipe of size 1150 mm long between dia & fixed completed all as specified and directed. 52.00 S & F Flushing jet for pedestal pattern WC incl. flexible pipe and Brass Chromium Plated nuts and blots and water pipe of size 1150 mm long between dia & fixed complete all as specified and directed. 53.00 S&F in repair bib taps long body cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket or PPR pipe etc making good disturbed portion complete all as specified and directed. 54.00 Taking down eaves gutters and rainwater pipes (any size or pattern) from floor / wall including all fittings,heads, shoes, bends, swan-necks etc complete all as specified & directed. 55.00 S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints etc complete all as specified and directed. 56.00 S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified & directed. 57.00 S&F 110 mm PVC (SWR) junction single,(Single T) equal or unequal complete all as specified & directed. 58.00 S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints etc complete all as specified and directed. 59.00 S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified & directed. 60.00 S&F 75 mm PVC (SWR) junction single,(Single T) equal or unequal complete all as specified & directed. 61.00 S&F 110 mm PVC Pipe Vent Cowl complete all as specified & directed. 62.00 S&F 75 mm PVC Pipe Vent Cowl complete all as specified & directed. 63.00 S&F in repairs CP Soap dish 100mm dia fixed with cp screws etc complete all as specified and directed by the Engineer-in-charge. 64.00 Removing or dismantling of damage / cracked/ concrete /loose concrete / plaster of ceiling/ wall/ chajja/ facia to expose the sound and hard concrete using a suitable mechanical device or by hammer and chisels etc complete all as specified & directed. 65.00 M & L for applying 25 mm thick ( average ) repair mortar ready to use single component polymer modified repair mortar for repair of RCC members likes beams, columns, chajja and facia/Ceiling, mortar having good compressive strength and shrinkage resistance etc complete all as specified & directed. 66.00 M & L for applying bonding agent for bonding old to new concrete surface likes chajja/ beams/ celings/ columns/ facia etc by high performance modified Styrene- Butadiene Rubber ( SBR ) base binder. Applying of binder is as 10 sqm/ per lit etc complete all as specified & directed. 67.00 Taking down chowkats or frame with shutter (without taking off shutters from the frame) exc 1.5 Sqm but n.exc 4 sqm each complete all as specified and directed. 68.00 Taking down chowkats or frame with shutter (without taking off shutters from the frame) n exc 1.5 Sqm each complete all as specified and directed. 69.00 S&F for Mild steel framed work as in chowkhat / frame of doors or gates of angle or other section with gusset plates, rails, braces,hold fast etc., complete all as specified and directed., drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete, quality conforming grade Fe- 290 or E- 165 complete all as specified and directed. 70.00 S&F Factory made flush shutter 30 mm thick solid core construction with block board core and plywood face panels commercial type complete all as specified & directed. 71.00 S&F of factory made soild PVC door frame of size 50mmx47mm made out of 5mm thick single side prelam PVC sheet reinforced with mild steel square tube , supplying & fixing in opening as per specification and drawing complete all as specified & directed. . 72.00 S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face with particle board core, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. 73.00 S&F 200 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified & directed. 74.00 S&F 150mm long aluminium anodized barrel tower bolt of extruded section complete all as specified & directed. 75.00 S&F Aluminium alloy, anodised, 250 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. 76.00 S&F Mild steel butt hinge medium weight cold rolled of size 100 mm long and fixed with screw/ welding complete all as specified and directed. 77.00 S&F 100 mm long extruded type B-22 aluminium alloy with galvanised mild steel hinge pin, anodised and fixed with screw/ welding complete all as specified and directed. 78.00 S&F 150 mm long aluminium anodized handle cast type complete all as specified and directed. 79.00 M&L 100 mm long aluminium anodized handle cast type complete all as specified and directed. 80.00 Providing & fixing of windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy-duty stain less steel pivot hinges shall be provided per shutter. The windows should be panelled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self-expanding, screws. Including 10mm square guard bars with 6” (152.4mm) pitch including making good of existing surface with obd/whitewash over plaster after fixing window etc complete for finished item of work including of all taxes etc as specified and directed. 81.00 Providing and Fixing of ventilator made of pre-painted steel (Base steel as per IS 513 of 0.58 mm thick “D” Quality galvanized as per IS 277 with Zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 48x50mm, centre mullion should be of 48x50mm, section for shutter should be of 52x 25mm and rebate for Glazed shutter with a 20mm provision for Guard bars/Grills. The sections are to be cut to length metre joined with corner bracket. Centre mullion is to be fixed with mullion cap. Handle, stay, 2 nos. of Stainless Steel heavy duty Pivot hinges shall be provided per shutter the windows fitted with 4mm thick plain float glass with rubber gaskets including fixing the frames in concrete/masonry wall by means of self expanding screws, Including fixed panel beading section should be of 12x12mm. Outer frame and mullions to have 10mm Square guard bars with 6” (152.4mm) pitch etc, complete for finished item of work. 82.00 M&L for Two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer including preparation of new or previously untreated surfaces of wood of any description not otherwise described over 10cm in width or girth complete all as specified. 83.00 M&L for one coats of synthetic enamel paint (Ordinary tint) including preparation of old surfaces of wood of any description not otherwise described over 10cm in width or girth complete all as specified. 84.00 M&L for one coats of synthetic enamel paint (Ordinary tint) including preparation of old surfaces of steel of any description not otherwise described over 10cm in width or girth complete all as specified and directed. 85.00 M & L for earthing complete with copper earth plate electric 60 cm x 60 cm x 3.15mm buried directly and vertically in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to Copper strip 20 x 3 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised steel and including necessary earth work execution in any type of latent rock, PCC 1:3:6 type C2 chamber and chamber cover 50mm (PCC 1:2:4) with 8 mm dia CTD reinforcement watering pipe 20mm dia GI, protection pipe for copper strip 40mm dia GI light grade, salt, coal, magnesium sulphate and water funnel etc complete all as per electrical plate No 4 of SSR Part I including dismantling of old earthing complete all as specified and directed. 86.00 M&L for earthing with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mtr below ground level) with top edge of earth plate not less than 1.5 Mtrs below ground level connected to GI strip 32x6mm as earth lead by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, including PCC (concrete chamber) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate, with fair finish internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire gauge mesh, 80 mm thick RCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified including provision of GI strip protected by 40 mm dia medium grade pipe and watering pipe shall be 20mm bore medium grade, and including all excavation and earth work & connecting the earthing to an earthing test point including dismantling of old earthing complete all as specified & directed. 87.00 S&F in repair to existing panel board by replacing the bus bar channel, welding, chasing, bending, replacement of hinges, Nut and bolt fixing, greasing after removing/replacement the rusted/corrugated sheet/panel door and spray painting of feeder pillar boxes/busbar boxes complete with existing colour, one coat of primer and two coat of synthetic enamel paint by spray painting to achieve smooth and uniform finish incl removal of existing paint,filling up cavities and writing of pannel location with black paint complete all as specified and directed 88.00 Supply, fixing, connecting and testing MCCB, 160 Amps, 4 pole with breaking capacity 35 KA, 415 volt 50 Hz, adjustable thermal setting and fixed magnetic setting with extended terminals including taking down of unserviceable MCCB of any type and capacity complete all as specified and directed 89.00 Supply, fixing, connecting and testing MCCB, 250 Amps, 4 pole with breaking capacity 35 KA, 415 volt 50 Hz, adjustable thermal setting and fixed magnetic setting with extended terminals including taking down of unserviceable MCCB of any type and capacity complete all as specified and directed 90.00 Supply, fixing, connecting and testing MCCB, 400 Amps, 4 pole with breaking capacity 36 KA, 415 volt 50 Hz, adjustable thermal setting and fixed magnetic setting with extended terminals including taking down of unserviceable MCCB of any type and capacity complete all as specified and directed 91.00 Supply, fixing, connecting and testing MCCB, 630 Amps, 4 pole with breaking capacity 36 KA, 415 volt 50 Hz, adjustable thermal setting and fixed magnetic setting with extended terminals including taking down of unserviceable MCCB of any type and capacity complete all as specified and directed
