Tender For Repair/Maintenance To Misc B/R Works In Zone-Iia Area Under Age B/R-Ii Of Ge Jaipur.; 1 Taking down existing roof treatment complete including demolition ofPCC, Mud phuskas, lime concrete etc any description upto mother slab, and properly cleaning the surface to remove loose particles with wire brushes and removing the debris out side of MoD land complete all as specified and as directed by Eng- In-Charge. 2 Supply and laying water-based, single component UV resistant, elastomeric PU liquid water proofing coating, having SRI >109 with an elongation of >400% and tensile strength of 1.4 MPa as per ASTM D 412, 80 % Solid Content, shore A Hardness of min. 50 as per ASTM D 2240 using roller in four layer (Primer coat,First coat, Fibre reinforce mesh & final coat) providing 1.2 mm DFT as per manufacturers specifications and instruction complete all as specified and directed. Application:- (a) Surface to be treated shall be free from loose particle etc then apply first coat of liquid water proofing as a primer on the surface with diluting as per manufacture instruction and allow the surface to dry for min 10-12 Hr time period. (b) Apply Second coat of Liquid water proofing without dilution on the primed surface and allow time to dry the surface for min 10-12 hr. (c) Apply Fibre reinforce mesh as per manufacturers instruction (iii) Applying third coat of liquid water proofing without dilution over the fibre rei coat and Allow minimum 48 hours before subjecting the painted surface to service.Note : (i) Work shall be carried out through authorized applicator of manufacturers only(ii) Material shall be used as per technical data / instruction of manufacturer after written approval of garrison engineer before execution at site and contractor shall submit guarantee of roof treatment work for TEN years Make:- Asian Paint : PU Aqua, M/s STP LTD-Shaliurethane BTD, Berger : Elastoseal BTD, Fosroc : Nito proof as approved by GE 3 M&L screed plaster 15mm thick in cement mortar (1:4) on concrete surfaces of roof to receive water proofing treatment and finished the surface even and smooth without using extra cement etc incl mixing of WPC as per manufacturers instruction complete all as specified and directed.Note:- Integral water proofing compound paid seperately as supply only 4 M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 40mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) finished even & smooth without using extra cement to cover negative slope into prop complete all as specified and directed 5 Supply only Integral water proofing compound ISI marked complete all as specified and directed. 6 Dismantling wall and ceiling board or insulation board etc, any thickness including snap grid frame, cover fillets etc complete all as specified and as directed. 7 Providing & Fixing ofMineral Fibre Acoustical Suspended Ceiling System with Dune Tegular 24 Edge Tiles of 16mm thickness and Prelude 24mm face exposed grid. The tiles shall have sand texture visual with acoustical punchers, Humidity Resistance (RH) of 99%, NRC 0.5 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 33db as per ASTM E1414, Light Reflectance ≥85% as per ASTM E-1477, Thermal Conductivity k = 0.052 - 0.057 W/mK, Colour Global White, Fire Performance of class 0/1 as per BS 476 Part 6/7 and Class A as per ASTM E84 with Board edge in module size of 600 x 600mm. It shall be suitable for Green Building application, with Recycled content of up to 41%. The tile shall have certifications from GRIHA and GreenPro thereby confirming that it is an environment friendly product. SUSPENSION: The tile shall be laid on Prelude 38 with 24 mm wide T - section flanges colour global white (matching to tile colour) having roll formed double stroke rotary stitching on all T sections i.e., the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 15 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 18kg/m. The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull-out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. INSTALLATION: To comprise main runner spaced at 1200mm securely fixed to the structural soffit using suspension system (specifications above) at 1200mm maximum. The First/Last suspension system at the end of each main runner shall not be greater than 450mm from the adjacent wall along with the first and the last main beam shall be at less than 600mm from the wall.Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm to form 1200 x 600 mm module.Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees.Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls using screws at 450mm centre to centre maximum. Installation shall be carried out as per recommended procedure.SUSPENSION SYSTEM accessories supplied byconsisting of M6 Anchor Fasteners with hanger hole, pre-straightened hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs. (Optionally, adjustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners). 8 M & L in repair 12mm thick perforated particle board/ tiles for insulation and accoustic purposes of any size fixed with nails to timber frame work or with staples on snap grid on walls flat or sloping (As per sample held with AGE B/R-II Sub Divn) complete all as specified and directed 9 Taking down chowkhats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed. 10 Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed. 11 Taking down shutters of any description of area exc 1 sqm but n exc 2 sqm each complete all as specified and directed. 12 S & F rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and incl either hooks and pintal hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete confirming to Fe-290 Gde-E-165 complete all as specified and directed 13 S & F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with 19 X 19mm MS square tube of 1.25 mm thickness. The profile shall be mitre cut at two corners and joined by inserting 2nos. of 150mm long brackets of 15x15mm M.S. square tube inside the 19mm x 19mm M.S. square tube and suitably screwed, suppling & fixing in opening as per specification & drawing given in SSR Part-I complete all as directed and specified. 14 S&F of Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and as directed. 15 S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk with steel screws incl fixing decorative laminate type-1 1.5mm thick of surface, colour and pattern as approved by engr-in-Charge and fixing with approved adhesive as per manufacturers instruction all as directed by Engr-In- Charge. 16 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 17 S&F factory made uPVC white colour Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension (Area of window upto 0.75 sqm.) comprising of uPVC multichambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge 18 Providing & fixing of double rebate windows made of pre painted steel as per IS 277. Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyster paint.Section of outer frame 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be 12x12mm and section forshutter be should be 52x25mm.Outer frame and mullions to have rebate for glazed shutters.Fly mesh with 20mm GI flat beading for provision of guard bars/grill .Fly mesh shuttersection 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to befixed with mullion cap. Handle, stay, 2 Nos of heavy duty stainless steel pivot hinges & 2 Nos of Aluminium powder coated tower bolt per shutter with 4mm thick float glass, SS 304 grade wire mesh & MS powder coated 10mm square guard bars complete as per approved drawing & direction of Engineer-in-Charge. 19 Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 20 S & F 35mm thick second class hardwood glazed and skelton door shutter,factory made, kiln seasoned and chemically treated, open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete all as specified and as directed by Engineer in Charge.The size of members of shutters shall be as specified in MES SSR Part-I. 21 S&F 4 mm thick sheet glass, odinary quality and glazing with oil putty in square exc 0.5 Sqm in each pane complete all as specified and directed. 22 S&F in repair sheet glass 3.00mm thick ordinary quality and glazing with and incl silicon in square n.exc 0.5 Sqm in each pane including hacking out old broken glass(any thickness, size, quality, or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed. 23 M & L Securing glass of any description in existing wooden frames glazed with putty/ beads including removing loose or decayed putty/ beads, painting/oiling one coat on rebates, grooves, fixing with silicon gel and painting/oiling puttied surface to match existing work complete all as specified and as directed. 24 M&L for solar control film 25micron reflective type sticked to glass panes as per instruction of manufaturer complete all as specified and as directed by Engineer in Charge.. 25 S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples in window or door complete all as specified and as directed. 26 M&L for powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators, Partion section with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 27 M & L powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beadingscrews etc. complete all as specified. 28 M & L powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified 29 S&F 30 mm thick Flush shutters, factory made, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed 30 M&L for preparation of new wooden or wood based surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 31 S & F 100 mm butt hinges medium weight stainless steel and fixed complete all as specified and as directed. 32 S & F 150mm long SS barrel tower bolts and fixed complete all as specified & as directed. 33 S & F 250mm long stainless steel sliding door bolt, plate type, not less than 12mm dia with & including a min of six bolt & nut, four on bolt plate & two on staple plate and fixed complete as directed and specified. 34 S & F stainless steel handles of size 150 mm fancy type of approved make and fixed complete all as specified & directed.Make : Godrej, Hindware, Lifetime or equivalent 35 M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in CM 1:6 complete all as approved and directed. 36 M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm, on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed 37 M&L for coloured jointfree non skid ceramic tiles, 300 x 300 x 7 to 8 mm thick (Square/rectangular) in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed 38 M&L for coloured glazed ceramic tiles 450mm X 300mm X 7 to 8mm thick on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed 39 Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed. 40 Taking up or down 15 mm steel tubingand connections including cleaning for refixing or removal complete all as specified and directed. 41 S&F 15 mm dia steel water tubing, galvanized, medium grade, with all fittings,fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge 42 Taking up or down 20 mm steel tubingand connections including cleaning for refixing or removal complete all as specified and directed. 43 S&F 20 mm dia steel water tubing, galvanized, medium grade, with all fittings,fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge 44 Taking down eaves gutters, sanitry PVC pipes and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed. 45 S&F 75 mm bore UPVC (SWR) rain water and drainage pipes (type A conforming to IS-13592) single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed. 46 S&F 75 mm dia UPVC (SWR) bends any radius complete all as specified and as directed. 47 S&F 110 mm bore UPVC (SWR) rain water and drainage pipes (type A conforming to IS-13592) single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed. 48 S&F 110 mm dia UPVC (SWR) bends any radius complete all as specified and as directed. 49 Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises complete all as specified and directed. 50 S&F in repair PVC Connections 15mm size, 600mm long with PTMT nuts complete all as specified and as directed. 51 S&F in repair UPVC (SWR) floor trap oulet dia 75mm, plain with CP grating including jointing with solvent cemet complete all as specified and as directed. 52 S&F in repair 15mm bore stop/angle valves, cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed for iron pipes or for unions and fixed complete all as specified and directed. 53 S&F in repair tubular towel rail, brass chromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed. 54 S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed 55 Dismantling old unserviceable RCC / PVC water tank of capacity exc 250 ltr but n exc500 ltr & removal from site complete all as specified and directed 56 S&F 500 Ltrs capacity rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc complete all as specified in SSR Part I and directed by Engr-in-charge. 57 Supply & fixing in repair vitreous china squatting pan, Orissa patteren, size 580 x 440 mm, white, with integral foot rests including P or S trap (excluding flushing cisteren and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. complete but including trap set in concrete incl seat and cover for pedestal pan, flush pipes to pedestal pan, including all joints and making good to the floor complete all as specified & directed. 58 S&F in repair 110mm PVC(SWR) WC connector with lip ring complete all as specified and directed. 59 S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), including plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device and connection to drain (or out going pipe) and to flushing pipe etc. incl trap set in cement concrete complete all as specified and directed. 60 S&F in repairs PVC valveless, syphonic action type flushing cistern, low level, 10 ltr capacity, white, with intel, ball valve, float and handle including brakects, 32 mm dia polyethylene of low or high density or PVC flushing pipe and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified & as directed. 61 S&F in repairs vitreous china wash hand basin with pedestal white flat back size 580 x 450 mm excluding taps, waste pipe, chain & plug and porcelene stopper but including brackets /fastners, cutting for and pinning in ends of brackets complete all as specified and directed. 62 S&F in repair 32mm bore (dia of discharge pipe) waste coupling of brass, chromium plated (half or full threaded) incl waste pipecomplete all as specified and directed. 63 S&F in repair 15mm bore pillar tap, long body cast copper alloy, chromium plated, fancy type with capstan head, screwed down, high pressure with or without lettered Hot or Cold with long screwed shank and fly nuts screwed for iron pipe complete all as specified and directed. 64 S & F in repair 15mm bore wall mixer, brass, chromium plated, fancy type, 3-in-1 for mixing hot & cold water, with L-bend pipe for connection to overhead shower, bright finish with three joints screwed the ends for iron pipeand plugging complete all as specified and directed. 65 S&F in repair Brass chromium plated shower rose 300mm size with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed. 66 S & F for Pipe Supporting Clamping for Single Pipe of dia 110 mm (4) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt Rubber Sleeve mounted System running vertically with wall distance 75 mm (3):Pipe Support Clamping made of : 1. Profile Bracket having Wall Distance 75 mm (3) made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923.2. Continuous Slotted C Channel with ribs to be used of size 250 mm (10) made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied+ Zn Al Flake coated with material thickness of 3mm. 3. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated.Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1.Material Qty. for one unit : 1. Profile Bracket Wall distance 75 mm (3) - 2 Nos. 2. Continuous Slotted C Channel of Size 250 mm (10) - 1 No.; 3. U Bolt Rubber sleeve mounted for 110 mm (4) CI or PVC Pipe Dia. - 1 No.; and 4. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2) - 4 nos. 67 S & F for Pipe Supporting Clamping for Single Pipe of dia 75 mm (3) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt Rubber Sleeve mounted System running vertically with wall distance75 mm (3):Pipe Support Clamping made of :1. Profile Bracket having Wall Distance 75 mm (3) made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923.2. Continuous Slotted C Channel with ribs to be used of size 250 mm (10) made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied+ Zn Al Flake coated with material thickness of 3mm. 3. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns).Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 75 mm (3) - 2 Nos. 2. Continuous Slotted C Channel of Size 250 mm (10) - 1 No.; 3. U Bolt Rubber Sleeve mounted for 75 mm (3) CI or PVC Pipe Dia. - 1 No.; and 4. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2) - 4 nos. 68 Dismantling wrought iron or mild steel, including gates work of any description not otherwise provided for complete all as specified and directed. 69 S&F rolled Mild Steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde E-250) qulaity A including fabrication, erraction and fixing complete all as specified and directed. 70 M&L pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws /J hook, L-type crancked hook complete all as specified and directed 71 Dismantling CGI / asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings including ridges complete all as specified and directed. 72 S & F Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of 15mm dia complete all as specified and directed.Note : Min weight for 15mm - 142gm 73 M&L for 100mm thick cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) as in flooring and all other similar works finished even and fair complete all as specified and directed. 74 M & L for 75mm thick PCC 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length.Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed . 75 Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15cm thickness (below or above ground level) complete all as specified and as directed 76 S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing including refixing all fittings complete all as specified and directed 77 S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing in SSR complete all as directed and specified. 78 M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. 79 M&L for Rounding to edges of stones slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed. 80 S&F factory made single extruded WPC (Wood Polymer Composite) solid plain shutter for cupboard of 18mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws complete all as specified & directed. 81 S & F auto close hinges, stainless steel of grade SS-304, bright finish, for cabinet of 1.5mm thickness and fixed complete all as specified.Make : Godrej, Hindware, Lifetime or equivalent 82 S & F stainless steel handles of size 75 mm, fancy type of approved make fixing with screws complete all as specified & directed. 83 S & F 300mm, ordinary rat tailpattern springs including roller and roller plate complete and fixing on stone or concrete chowkat flat iron 40x3 mm size 75mm cm long with necessary bolts complete all as specified and as directed by Engr-In-Charge. 84 S&F mild steel mortice lock, vertical type, size 100mm, 4 Levers with escutcheon plates & two keys fixed in any frame complete all as specified 85 S&F Door closer aluminium anodized extruded section body, hydraulically regulated designation No-3, universal type, suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 Kg complete all as specified and as directed. 86 Taking down cement plaster or cement lime plaster, any description on brick, stone walls or concrete surface of ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed 87 M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick masonry surfaces or concrete surface finished even and smooth without using extra cement complete all as specified and directed. 88 M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick masonry surfaces or concrete surface finished even and smooth without using extra cement complete all as specified and directed. 89 M&L for preparation of newly plaster surface of walls and applying two coats of premium exterior emulsion paint, 1st quality (company depot tinted) of approved manufacturers in required colour and shade using hand roller over and including one coat of alkali resistant priming paints complete all as specified and directed . 90 M&L for preparing newly plastered surfaces of wall, AC sheet, RCC jallies etc and applying two coats of distemper with distemper oil emulsion white or tinted over a coat of primer complete all as specified and directed. 91 Demolition of brick work or stone/ boulder masonary, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed. 92 M&L for brick work with sub-class B bricks (old size), straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed 93 M & L for removing of air blockage or air lock in existing water pipe of any dia through manual or pressure motor or any other means complete all as specified and directed. 94 Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule A/BOQ
