Tender For Provision Of Guard Room And Toilet Near Main Gate Of 6 Afh At Coimbatore; 1 Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in hard and dense soil, complete all as specified and directed. 2 Excvation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth in hard / dense soil and getting out, complete all as specified and directed. 3 Excvation in trenches not exceeding 1.5m wide and exceeding 1.5m in depth butnot exceeding 3.0m in depthin hard / dense soil and getting out, complete all as specified and directed. 4 Returning filling in including spreading leveling and well ramming in layers not exceeding 25 cm thick, complete all as specified and directed. 5 Removing excavated materials (soils) to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point, all as specified and as directed. 6 Removing excavated material to a distance exceeding 250m but not exceeding 500 m and depositing where directed at a level not exceeding 1.50m from starting point,all as specified and as directed. 7 Material & Labour for Morrum / Sand filling under floors or in foundation, including watering and consolidation etc all as specified and directed 8 Earth cushioning to UG cables using excavated soil riddled by using large sieve to separate the composite particles/roots etc and refilling in trenchesall as specified andas directed.Note :Punned thickness will be measured for payment. 9 Material & Labour for Hardcore Broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rolled/ rammed to a true surface,all as specified and as directed. 10 Material & Labour forAnti Termite Treatment Treating Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface, all as specified and as directed.Note: The treatment at footing shall be depth of 500mm below G.L and The treatment at junction of wall shall be depth of 500mm below G.L (Area of the sub structure in contact with backfill to be measured) 11 Material & Labour for Anti Termite Treatment Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface, all as specified and as directed. Note: The treatment shall be at floor area 12 Material & Labour forAnti Termite Treatment TreatingTreating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area, all as specified and as directed.Note: The treatment shall be at plinth protection area around the building 13 Material & Labour forAnti Termite Treatment TreatingTreating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, all as specified and as directed.Note: The treatment shall be along the external perimeter of the wall of building 14 Material & Labour for Plain Cement Concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete, all as specified and as directed 15 Material and labour for Plain Cement Concrete (1:2:4) type B-2 (using 40 mm graded crushed stone aggregate)in foundations,filling and massconcrete, complete all as specified and as directed. 16 Supply only liquid water proofing compound, complete all as specified and as directed. 17 Material & Labour for cement concrete type C-1 1:3:6 (20mm graded aggregate) a in coping, benching concreteincluding necessary use and waste of Form work etc complete all as specified and as directed. 18 Material & Labour for Plain Cement Concrete block masonry, type C1 1:3:6 (using 20mm aggregate stone aggregate) setting in cement mortar 1:4 with solid blocks exceeding 10cmin width, complete all as specified and as directed. 19 Material & Labour for precast reinforced concrete type B-1 1:2:4 (using 20mm graded stone aggregate) set in cement mortar 1:4 as in cover slabs, complete all as specified and as directed. 20 Material & Labour forReinforcrd Cement Concrete Grade M-25, Design mix (using 20mm aggregate stone aggregate)in foundation, including rafts, footings, plinth beams, bases for columns etc and mass concrete, complete all as specified and as directed. 21 Material & Labour forReinforcrd Cement Concrete Grade M-25, Design mix (using 20mm aggregate stone aggregate) as in floor or roof slab supported on walls and the like, complete all as specified and as directed. 22 Material & Labour forReinforcrd Cement Concrete Grade M-25, Design mix (using 20mm aggregate stone aggregate) in Lintel / chajja and roof beam over 1.5 m span, complete all as specified and as directed. 23 Material & Labour forReinforcrd Cement Concrete Grade M-25, Design mix (using 20mm aggregate stone aggregate) in columns above ground level, complete all as specified and as directed. 24 Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, mounds etc, all as specified and as directed. 25 Supply and lay burnt bricks sub-class B designation 75 for cable protection, all as specified and as directed. 26 Material & Labour for Form work to sides of Concrete foundation , footings, bases of columns, raft beams and soffits of foundation and plinth beam and similar work vertical or to batter etc with fair finished surfaces of concrete flat,all as specified and directed 27 Material & Labour for Formwork to soffits of suspended slabs such as roof slab, floor slabs, landings and similar work not exceeding200mm thick (horizontal or sloping) rough finished flat surfaces, all as specified and as directed. 28 Material & Labour for Formwork for sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels/ Chajjas, cantilevers, shelves inlcuding supports overhangs, etc also splays between floors and beams etc, all as specified and as directed. 29 Material & Labour for Formwork to sides of pillars, posts, struts, column etc rough finishes of concrete surfaces flat all as specified and directed. 30 Material & Labour for Formwork to edges of concrete roof slab exceeding 10 cm but not exceeding 20 cm thick rough finished flat surfaces etc, all as spesified and directed. 31 Providing and fixing factory made uPVC white colour casement (Openable) window (incl frame & shutter)(Area exceeding 1.00 sqm but not exceeding 2.00 sqm each)made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +/– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges ofzinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass, complete all as spesified and directed.(Note: The unit rate quoted by contractor excludes cost of glass/ wire mesh and includes all other connected accessories.) 32 Providing and fixing factory made uPVG white colour Sliding window Two track (incl frame & shutter)(Area not exceeding 2.00 sqm each)made of extruded profiles with wall thickness of 2.3mm (+ /-0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories, complete all as spesified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) 33 Providing and fixing factory made uPVC white colour casement (Openable) Door (include frame & shutter) made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated), Door stopper [and 5mm thick glazing with selected quality glass, complete all as spesified and directed. (Note: The unit rate quoted by contractor excludes cost of glass/wire mesh and includes all other connected accessories.) 34 Supply & Fixing Factory made single extruded WPC (Wood S&F Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp- ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length, complete all as spesified and directed. Note: (i) M.S. hold fast/ lugs or SS dash fasteners shall be measured & paid separately(ii)For WPC solid door / window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 35 Supply & Fixing Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 25mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as spesified and directed. (Note: stainless steel butt hinges and necessary S.S screws shall be measured &paid separately) 36 Supply & FixingProviding and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type panel of size 18mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws,complete all as spesified and directed. (Note: stainless steel butt hinges and necessary S.S screws shall be measured &paid separately) 37 Supply & Fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or steel screws, complete all as spesified and directed. 38 Supply & Fixing 25mm diaStainless Steel curtain rails with decorative type fixing brackets, stops, rollers etc. all as specified & directed. 39 Supply & Fixing soft close telescopic drawer channel, not exceeding 550mm length, sidemount type,suitablle for weight upto 35 kg all as per Model No 8179 of Make - Godrej(or equivalent in other makes), complete all as spesified and directed. 40 Supply & Fixing 50mm dia, polished, hard wood knobs fixed with screws, complete all as spesified and directed. 41 Supply & Fixing Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in, complete all as spesified and directed. 42 Supply & Fixing 30mm flap width Brass Continuous (piano) hinges with necessary fittings and screws etc, complete all as spesified and directed. 43 Supply & Fixing aluminium (extruded section) body door closed hydraulically regulated, designation No 3 universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg, complete all as spesified and directed. 44 Supply & Fixing Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty,all as specified and directed 45 Supply & Fixingtubular brass chromium plated Towel rail 20 mm dia D type 60 cm long between flanges, complete all as spesified and directed. 46 Supply & Fixing Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as spesified and directed. 47 Material & Labour for bars 12mm dia for handles confirming to Fe 290 Gde E-165, complete all as spesified and directed. 48 Material & Labour for TMT bars for reinforcement 10mm dia and over cut to lengths, bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9mm dia 49 Material & Labour for TMT bars 5mm dia and over and upto and including 10 mm diacut to length bent to shape required including cranking bending and binding with MS wire not less than 0.90mm dia, complete all as spesified and directed. 50 Material & Labour for TMT bars for reinforcement 6mm to 8mm dia cut to lengths, bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9mm dia, complete all as spesified and directed. 51 Material & Labour for TMT bars for reinforcement 5mm and over upto 10mm dia in stirrups, spaces and binders,cut to lengths, bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9mm dia, complete all as spesified and directed. 52 Material & Labour for providing and fixing mirror polishing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts, capsetc., of required size, on the top of floor or the side of waist slab with suitable arrangement,all as specified and directed 53 Material & Labour for powder coated aluminum frame for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified & directed. 54 Material & Labour for powder coatedAnodised aluminium window and ventilator shutters, side or top hung type without sash bars, aluminium sections weighing 0.55 kg / m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long,hinges type B-21, 100mm longsuitable handle and all necessary fittings, complete all as specified & directed. 55 Material & Labour for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing as shelf slabs, complete all as specified & directed. 56 Rounding to edges of stone slabs one edge, such as in steps, shelf slabs, platform, and other similar situations, complete all as specified & directed. 57 Material & Labour for 75mm thick Plain Cement Concrete 1:3:6 typeC2 (using 40 mm graded stone aggregate) in sub base of flooring & plinth protection etc, complete all as specified & directed. 58 Material & Labour for coloured Non skid coloured tiles superior finish grade B-1 quality 7 to 8mm thick(square / rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.16 sqm in floor with rectified edges ( joint free) etc set and jointed in neat cement slury over cement screed 15 mm thick 1:6, complete all as specified & directed. 59 Material & Labour for Coloured glazed ceramic tiles economy finish Gde B-II (b) quality of size 450 x 300 x 7 mm thick with rectified edges as in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10 cm thick backing coat with cement mortar 1:4,complete all as specified & directed. 60 Material & Labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete set and jointed in neat cement slury over cement screed 15 mm thick 1:6,complete all as specified & directed. 61 Material & Labour for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillarand jointed including rubbing and polishing complete set and jointed in neat cement slury overand including 10 cm thick backing coat with cement mortar 1:4,complete all as specified & directed. 62 Material and labour 15 mm thick cement plaster in cement mortar 1:4 , finished even & smooth without using extra cement,complete all as specified & directed. 63 Material and labour 10 mm thick cement plaster in CM 1:6 ,finished even & smooth without using extra cement,complete all as specified & directed. 64 Material and labour 5 mm thick cement plaster in cement mortar 1:3 for ceiling finished even & smooth without using extra cement,complete all as specified & directed. 65 Material & Labour for applying Twocoats ofacrylic emulsion paintof Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives over and including priming coat of exterior primer applied on new plastered surfacesofwallsincluding preparation of surfaces, complete as mentioned in SSR all as specified and as directed . 66 Material & Labour for 20mm thick granite work (table rubbed polished ) for wash basin tops including pointing in white cemnet 1:2 using marble dust with admixture of pigment to match with shade of granite, laid over15mm thick screed bed in cement mortar 1:4,complete all as specified & directed. 67 Material & Labour for 10 mm thick rendering in cement mortar 1:3 mixed with liquid water proofing compound(to be mixed as permanufacturer instruction)on concrete surfaces of roof and making the surfacesfinished fair and even as in required slope for draining out the rain water all as specified and directed.Note -Water Proofing Compound shall be measured and paid for separately 68 Material & Labour for 15mm thickrendering in cement mortar 1:4, on fair faces or brick work or concrete surface using waterproofing compound (to be mixed as permanufacturer instruction) finished fair and even, all as specified and directed.Note -Water Proofing Compound shall be measured and paid for separately. 69 Material & Labour for three coats of white washon newly plasterd ceiling surfaces including preparation of surfaces,all as specified and directed. 70 Material and labourTwo coats of Oil bound distemper over a coat of primer over one coat of 3mm wall care putty on walls, pillasters, cornices, etc., on newly plastered wallsincludingpreparation of surfaces,all as specified and as directed. 71 Material & Labour for 3 mm thick figured glass pin head type and glazing with oil putty in square not exceeding 0.5 sqm in each pane,all as specified and as directed. 72 Material & Labour for 4.8 mm thick sheet glass, ordinary quality and glazing with wooden beading not exceeding 0.5 Sqm in each panewith solar control film 50 micron reflective type sticked to glass pane, all as specified and directed. 73 Material & Labour for 12mm thick Toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required with solar control film 50micron reflective type sticked to glass pane including holding clips and necessary fittings, all as specified and directed. (Note : Pattern of Tint as approved by Engr in charge) 74 Material & Labour for two coats synthetic enamel paint on new steel surfaces of any description, over 10cm in width or girth, over a coat of red oxide primer, all as specified and directed. 75 Supply and application of single component, seamless, spray applied, hybrid elastomeric PU based material i.e Nitoproof 725 of Fosroc chemicals (or) sikalastic 590 of Sika India Pvt Ltd (or) equivalent in Bostic India Ltd over a coat of primer i.e Nitoproof WB primer of Fosroc chemicals (or) diluted sikalastic 590 of Sika India Pvt Ltd (or)equivalent in Bostic India Ltd,all as specified and directed. Note:-(i) Average minimum DFTof PU based material shall be 1mm and shall be applied by using a Graco pump.(ii) PU based material shall process the following properties solids by volume -65%, tensile strength ASTM D412-1.75Mpa, density 1.3 g/ml, elongation ASTM D-412-350%, Adhesion to substrate concrete-1.9Mpa, resistance to water-10m pressure.(iii) Rate are deemed to be include for cleaning and preparation of surface to receive PU water proofing system including filling of cracks with cementitious repair mortars i.e renderoc CS of Fosrock chemicals (or) equivalent of approved make.(iii) Work shall be got carried out by authorised applicator of the manufacturer and it shall be got approved by the AGE(I) before progressing the work.(iv) 10 years of guarantee shall be provided and security amount shall be deposited as speicified in tender documents. 76 Supplying and laying 16mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls / ceiling or laying in floors complete all as specified and directed.Note :-Cutting chases on stone walls / Block walls, pinning in,making good to facings where required and pointing in cement mortar 1:3 for cutting chases for concealed water tubingetc. and making good. 77 Supplying and laying 20mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.Note :-Cutting chases on stone walls/ Block walls , pinning in, making good to facings where required and pointing in cement mortar 1:3 for cutting chases for concealed water tubingetc. and making good. 78 Supplying and laying 25mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, complete all as specified and directed. 79 Supply and fixing vitreous chinawash down water closet panpedestal patternwhite including PVC valveless, syphonic action type,flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe including all accessoreis i.e seat cover andHealth faucet jets of ABS body (1 mtr long pipe 15mm dia), complete all as specified and directed. 80 Supply and fixing Vitreous Cliina wash basin, counter top, size 400x400mm white, including fancy pillar tap taps Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for any pipe and fixed, waste, chain and plug and porcelain stopper but including brackets, complete all as specified and directed. 81 Supply and fixing 900 mm x 450 mm bevelled edge frame less mirror of selected quality glass, mounted onand fixed towith chromium plated brass screw and cup washer, complete all as specified and directed. 82 Supply and fixing 15mm fancy type bib taps chromium plated round handle, screwed down, screwed for iron pipe and fixed(Type Long body as specified by Engr in charge), complete all as specified and directed. 83 Supply and fixing 15mm fancy type stop valves, chromium plated, screwed down, high pressure, with crutch or round handle screwed bolts ends for iron pipe or for unions and fixed, complete all as specified and directed. 84 Supply and fixing PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed. 85 Supply and fixing Grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40gms), complete all as specified and directed. 86 Supply and fixingFancy type square shape swivel shower of CP for fixing with 15 mm pipe, complete all as specified and directed. 87 Supply and fixing75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed in wall/ floor with necessary clamping where required, complete all as specified and directed. 88 Supply and fixing110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed in wall/ floor with necessary clamping where required, complete all as specified and directed. 89 Supply and fixing (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm dia inclduing fixing to existing pipe properly with solvent all as specified and directed 90 Supply and fixing PVC bends for 75 mm bore pipe, complete all as specified and directed. 91 Supply and fixing PVC bends with access doorfor 110 mm bore pipe, complete all as specified and directed. 92 Supply and fixing PVC (SWR) vent cowl 110 mm dia, complete all as specified and directed. 93 Supply and fixing Chromium Plated soap dish and shampoo holder, complete all as specified and directed. 94 Supply, Hoisting and fixing 750 Ltr cap PVC water tanks rotational moulded polyethylene water storage tank cylinderical vertical with same capacity with closed top hoistedand fixed in position all as specified in SSR part Iincluding complete set of ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron / CPVC pipe and fixed ofsize 25 mm dia, complete all as specified and directed. 95 Material & Labour for 40mm bore dia High density polyethylene pipes (HDPE) of pressure rating 6 kgf / Sqcm,complete to walls, ceilings or in floors as drain out pipe etc, complete all as specified and directed. 96 Material & Labour for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in bed to drain pipes 150mm dia including packing under and haunching against the sides of pipesafter they are laid and tested, complete all as specified and directed. 97 Material & Labour for PVC (SWR) 150 mm dialaid and jointed complete with collars, complete all as specified and directed. 98 Cutting exising manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel(1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1(using 20mm graded stone aggregate) smooth finished and reforming benching as required,(using 40mm graded stone aggregate), complete all as specified and directed. 99 Supplyng and laying of CPVC pipes SDR 11 & plain CPVC SDR 11 fittings in trenches complete of size 32 mm outer dia, complete all as specified and directed. 100 Material and labour for cutting of existing steel water tubing for additions or alterations in GI pipe of size 40 to 50 mm diaand fix the CPVC pipe with existing pipe line, complete all as specified and directed. 101 Supply and fix ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed of size 20 mm dia (Minimum weight 210 grams)complete all as specified and directed. 102 Supply and fix ball valves high pressure with polythene float and flynut complete screwed/fixed in both ends of iron /CPVC pipes of size 25 mm,complete all as specified and directed. 103 Material and labour for cutting of existing cast iron pipes in any situation and insertain new tees, branches, bends,end plate etc in 100 to 150 mm dia CI pipe any type,complete all as specified and directed. 104 Supply and fix bends tapers, tee pieces end plate any type and size with nut bolts and washers of suitable size reqd at site for upto 150 mm dia pipe in any situation,complete all as specified and directed. 105 Supply and laying PVC non metalic conduit including tees, bends, elbows, reducers, and fixing accessaries etc for telephone / TV connection of size 20 mm dia all as directedNote (i) Cutting chaseswill be Measured and paid seperately (ii) TV/Telephone cable provide by user section . 106 Supply and fixingPVC non metalic junction boxes one to fourway for telephone / TV connection of size 20 mm dia,complete all as specified and directed. 107 Material & Labour for concealed Point wiring for light / bell point controlled by one, one way switch,complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistrandedcopper conductor drawn through in and including 20mm dia PVC rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling/roof/etc including 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed. Note: Cutting chases will be Measured and paid seperately. 108 Material & Labour for concealed Point wiring for ceiling / exhaust fan point controlled by one, one way switch,complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistrandedcopper conductor drawn through in and including 20mm dia PVC rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling/roof/etc including 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed. Note: Cutting chases will be Measured and paid seperately. 109 Material & Labour for concealed Point wiring for05 Amps socket outlet pointon same board,complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistrandedcopper conductor drawn through in and including 20mm dia PVC rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling/roof/etc including 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed. Note: Cutting chases will be Measured and paid seperately. 110 Material & Labour for concealed Point wiring for switch socket outlet point 5 Amps on independent board,complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistrandedcopper conductor drawn through in and including 20mm dia PVC rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling/roof/etc including 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed. Note: Cutting chases will be Measured and paid seperately. 111 Material & Labour for concealed Point wiring for 3 pin socket outlet, 15 Ampson independent board.,complete with 2.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistrandedcopper conductor drawn through in and including 20mm dia PVC rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling/roof/etc including 2.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed. Note: Cutting chases will be Measured and paid seperately. 112 Material & Labour for concealed Point wiring for light / bell point controlled by one, one way switch,complete with 4 sqmm single core PVC insulted FRLS cable 1100 volts grade multistrandedcopper conductor drawn through in and including 20mm dia PVC rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling/roof/etc including 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed. Note: Cutting chases will be Measured and paid seperately. 113 Supply & Fixing Switch Modular 6A single pole, one way, 1 module complete all as specified and as directed. 114 Supply & Fixing Switch Modular 16A single pole, one way, 1 module complete all as specified and as directed. 115 Supply & Fixing Modular Modular Bell Push 6A 1 Modulecomplete all as specified and as directed. 116 Supply & Fixing Socket, 6A - 2/3 pin combined 2 module complete all as specified and as directed. 117 Supply & Fixing socket Modular 6/16A 2/3 pin combined 2 module complete all as specified and as directed. 118 Supply and fixing LED lights fitting 1 x 18/ 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose,complete all as specified and as directed. 119 Supply and fixing LED light fitting mirror type withhigh out put diffuser 2 feet10 watt 220 V AC decorative type with driver holder and LED lampincluding connecting up with three core flexiblecopper conductor cable of suitable size,complete all as specified and as directed. 120 Supply and fixing LED light fitting round/squre type 12 watts 230 volts recessed/surfac type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof /celing including connecting up with three core flexiblecopper conductor cable of suitable size,complete all as specified and as directed. 121 Supply and fixing LED street light fitting 35 watt 230 V AC outdoort type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protectionincluding necessary mountingbracket with nut bolts and mounting on wall or roof etc including taking down unserviceable fitting,complete all as specified and as directed. 122 Supply and fixing Call Bell Ding Dong AC 230 V single polecomplete connecting up withflexible copperconductor cable of suitable size, complete all as specified and as directed. 123 Supply and fix exhaust/ventilating fans made of sturdy engineering plastic complete with louvers shuter voltage 230 volts, 50 Hz RPM 1200 copper winding of sweep 250 / 300 mm, complete all as specified and as directed. 124 Supply and fixing ceiling fans complete with blades, down rods electronic modularregulator two module and accessories 230 volts 1200 mm sweep minimum air delivery 210 CFM with service value 6.00 BEE five star rated with brushless direct current motor (BLDC), complete all as specified and as directed. 125 Supply and fix lamp holder PVC/Polycorbonate type with back plate suitable for battern/angle fittings, complete all as specified and as directed. 126 Supply and fix MCB DB, TPN, 4 ways, double door, 415 volt, Isolated neutral bar with IP54 protection, door earthing arrangement with cement spill protector, mechanical impact strength IK09 complete all as specified and as directed. 127 Supply and fix MCB SP 6 to 32 Amps, 240Volts, 10 KA, B Curve complete all as specified and as directed. 128 Supply and fixing TP 25 to 63 Amp rating 415 V, 10 KA C curve miniature circuit breaker (MCB) complete all as specified and as directed. 129 Supply and fixing TPN 32 Amp rating 415 V, 10 KA C curve miniature circuit breaker (MCB) complete all as specified and as directed. 130 Material & Labour for concealed Sub main wiring by making recess in wall/surface complete with 4 runs of 2.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 2.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories suface / concealed in wall / Ceiling etcfrom Main DB to MCB DB all as specified and as directed.Note :-4 runs of 2.5 sqmm, + 1 run of 2.5 sqmm (Earth Cotinuity conductor) and 1 run of PVC conduit shall be measured as one unit length. 131 Supply and fix ceiling rose surface type bakelite 65 x 50mm with three terminals, complete all as specified and as directed. 132 Supply and fix modulartelphone socket RJ 11 one module including taking down unserviceable socket, complete all as specified and as directed. 133 Supply and fix modularTV coaxial socketone module including taking down unserviceable socket, complete all as specified and as directed. 134 Supply and fix pre wired powerunit with 20 amps mimi MCB and plug top for ACincluding taking down unserviceable socket, complete all as specified and as directed. 135 Supplyng and laying of XLPE insulated armoured heavey duty electric cable with aluminium conductor 1100 volts grade cross sectional area 10 Sq mm 4 core including taking down userviceable cables, complete all as specified and as directed. 136 Supply and laying tubes light grade galvanised with all fittings laid in trenches of dia 50 mmall as directed for cable protection, complete all as specified and as directed. 137 Material & Labour for dismantling / cutting of existing road / path / hard standing cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) suitable for laying cable protection pipe 80 / 50 mm dia under the road / path / hard standing,complete all as specified and as directed.
