Tender For Maintenance Of Straw Shed Near L.I Quarters At Vengad Gokulam, guruvayur-Kerala

Tender For Maintenance Of Straw Shed Near L.I Quarters At Vengad Gokulam- 1 15.9.2Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceablematerial and disposal of unserviceable material within 50 metres lead as per direction of Engineer -inCharges:In cement mortar 2 15.28.1Dismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50metres lead of :G.S. Sheet 3 2.6.1Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas(exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavatedearth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds ofsoil 4 Providing Front end loader 1 cum bucket capacity (incl POL) 5 7.1.1Random rubble masonry with hard stone in foundation and plinth including levelling up with cementconcrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinthlevel with:Cement mortar 1:6 (1 cement : 6 coarse sand) 6 60.7.9RR with Departmental. Stone - Random rubble masonry using departmental rubble in foundation andplinth including through and bond stone and levelling up with cement concrete 1:6:12 (1 cement : 6coarse sand : 12 graded stone aggregate with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6coarse sand). 7 4.1.8Providing and laying in position cement concrete of specified grade excluding the cost of centering andshuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40nominal size) 8 5.9.5Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams,girders bressumers and cantilevers 9 4.1.3Providing and laying in position cement concrete of specified grade excluding the cost of centering andshuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mmnominal size) 10 50.6.2.2Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available sizeconfirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM1:6 ( 1 cement : 6 coarse sand) etc complete 11 10.26.3Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing,staircase railing and similar works, including applying priming coat of approves steel primer.G.I. pipes 12 13.1.112 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 13 10.2Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, includingcutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 14 13.33.1Pointing on stone work with cement mortar 1:3 ( 1 cement : 3 fine sand):Flush/ Ruled pointing 15 13.99.1Painting with synthetic enamel paint of approved brand and manufacture ofrequired colour to give aneven shade :One or more coats on old work 16 13.61.1Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two ormore coats on new work 17 12.50Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 gramsper sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet andpolyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum toavoid scratches during transportation and should be supplied in single length upto 12 metre or as desiredby Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm)with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shape wherever required. 18 21.1.2.2For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and makingprovision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasketrequired (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powdercoating 50 micron) 19 21.3.1Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDMrubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer -in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0mm thickness 20 Labour engaged as Assistant Fitter or 2nd class fitter. 21 Labour engaged as coolie

INR 930 /-

Refer document