Tender For Comprehensive Maintenance And Misc Work In Zone A2 Area Under Age Br I Of Ge West Mathura; 1 Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc. completeall as specified and directed. 2 Demolition of brick work or stone/boulders masonary, built in cement mortor including all quoins, arches pillars, etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed. 3 Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded, jointed and pointed in any mortar complete all as specified and directed by Engineer-in-charge. 4 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premisescomplete all as specified and directed. 5 Taking down chowkhats with shutter (without taking off shutters from the frame) area not exc. 1.50 Sqm each complete all as specified and directed. 6 Taking down chowkhats with shutter (without taking off shutters from the frame) area exc. 1.50 Sqm but n.exc 4.00 sqm each complete all as specified and directed. 7 Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each complete all as specified and as directed by Engineer-in-charge. 8 Refixing door shutters of any description having area exc 1.00 sqm but not exc 2.00 sqm, each in the same opening including easing of door / window/ cup board shutters for easy closing/ opening incl tighening of hinges or changing the position of hinges adjustment of tower bolts, sliding bolts etc complete all as specified and directed by Engineer-in-charge.Note :- Labour for taking down of shutter included in this item, nothing shall be paid extra. 9 Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roofs etc including ridges complete all as specified and directed by Engineer-in-charge. 10 Dismantling timber scantlings 40 sq. cm and over in section in framed work, in any position complete all as specified and directed. 11 Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) as in floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge. 12 Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thick above or below ground level complete all as specified and directed. 13 Dismantling of wall and ceiling boards of any type and any thickness including cover fillets complete all as specified and directed. 14 M&L for Brick work with sub class ‘B’ old size burnt bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-charge. 15 All as per Srl item No 14.00 here-in-before but except brick.Note : Old serviceable brick retrieved from serial item No 2.00 of BOQ here-in-before shall be used under this item. 16 S&F Pressed steel frame for doors of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed. 17 S&F Pressed steel frame for doors of size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed. 18 M&L for cement concrete type C-1, (1:3:6) using 20mm graded aggregate as in bed block or filling of chowkhats including necessary form work complete all as specified and directed. 19 M&L 35mm thick factory made glazed and skeleton shutters of 2nd class HW with partially panel shutter open rebated and prepared to receive glass / gauze etc edges or framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc as specified in SSR Part-1 section 8.24 (a) complete all as specified and directed. 20 S&F 35mm thick plain framed panelled door shutter, factory made (any number of panels) of 2nd class hard wood with lock rail and panels of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces including 2nd class hard wood kail beading 20mm wide tapering from 10mm to 5 mm on one side of shutter & fitted to chowkhats. The size of rail and style shall be as per IS –1003 (Part-I)(wood shall be kiln seasoned and chemically pressuretreated) complete all as specified and directed. 21 S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified & shown in relevant drawing of item No. 08095 in MES Schedule (Part-II) and directed by Engineer-in-Charge. 22 S&F30mm thick factory made solid PVC moulded door shutter with particle board core with 5mm thick PVC moulded sheet on the front face and 5 mm thick PVC plain coloursheet on back face complete all as specified and directed by Engineer-in-charge. 23 S&F powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 24 S&F powder coated Anodised aluminium window and ventilator shutters side hung type without sash, aluminium sections weighing 0.55 kg/ m including necessary joining cleats, glazing clips rubberpacking,anodised aluminium snap beading screws Anodise aluminium fitting such as peg stays 150 mm long (1 No ), including pag stay and hinges type B-21 100 mm long (2 No) and suitable handle (1 No) complete all as specified and directed. 25 S&F powder coated Anodised aluminium door section, aluminium sections weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing,anodised aluminium snap beading screws Anodise aluminium fitting such as including hinges 100 mm long (2 no) and suitable handle(2 No) complete all as specified and directed. 26 M&L for aluminium grill mesh made out of 6mm dia having girth not exc 25mm both ways fixed with aluminium cleat to window frame complete all as specified and directed by Engineer-in-Charge. 27 S&F powder coated aluminum partition using 95.6mmx 44.8mm x 1.00-1.2mm frame work with 12mm thick exterior grade veneered particle board with decorative veneers on both face/5.5mm thick frosted glass including aluminum beading for fixing board each panel n.exc 1.2 Sqm complete all as specified and directed by Engineer-in-charge. 28 M&L for in repair to aluminium door/window of any size/any description, taking off from present position and refixing in the same position after tightening, easing/change the section as required, including fitting the rubber packing aluminium snap beading resetting floor/hydraulic door closer/spring etc complete all as specified and directed. 29 S&F 5.5 mm thick frosted glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane. 30 S&F Sheet glass 4 mm thick in glazing to aluminium door, window & partition including pad, gasket complete all as specified and directed. 31 S & F 5mm thick coloured ACP (Aluminium composit Pannel) sheet using aluminium partition including joining cleats for fixing etc. (colour of sheet approved by GE). 32 S&F Mortice latch with two levers (vertical type), aluminium, anodised body and fixed complete all as specified and directed. 33 S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge. 34 S&F in repairs 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge. 35 S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge. 36 S&F 300 mmaluminium alloy, anodised sliding door bolts with hasp, staple and fixing clips of sheet, cast or extructed section and fixing bolltsand sliding bolts of extruded sectionor cast aluminium ally and fixed complete all as specified and directed. 37 S&F in repairs 300 mmaluminium alloy, anodised sliding door bolts with hasp, staple and fixing clips of sheet, cast or extructed section and fixing bolltsand sliding bolts of extruded sectionor cast aluminium ally and fixed complete all as specified and directed. 38 S&F Aluminium handles cast type anodised of size 150mm size,complete all as specified and directed. 39 S&F in repairs Aluminium handles cast type anodised of size 150mm size,complete all as specified and directed. 40 S&F 100mm long stainless steel Butt hinges fixed complete all as specified and directed. 41 S&F 140mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. 42 S&F in repairs 140mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. 43 S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge. 44 S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge. 45 Hacking out old broken glass any thickness, size, quality or description from wooden / metal frame and punching or drilling out old glazing pins/spring clips complete all as specified and directed by Engineer-in-charge. 46 M&L 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified and as directed. 47 M&L 3mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and directed by Engineer-in-charge. 48 M&L for 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate ) as in floor finishes and leveling course complete all as specified and directed. 49 M&L for glazed ceramic tiles (coloured) 450mm x 300mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) including necesary cutting as per site requirment complete all as specified and directed by Engineer-in-charge. 50 M&L Non skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with and including 15mm thick screed bed in cement mortar (1:6) for laying floor finishes complete all as specified and as directed. 51 M&L for non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular)area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:4) complete all as specified and directed by Engineer-in-charge. 52 All as per item No 51.00 (here-in-before) abvoe but as in skirting over 10mm thick backing coat in CM (1:3) complete all as specified and directed. 53 M&L for vitrified ceramic tiles light shade 8-9mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick cement screed bed in CM (1:4) complete all as specified and directed. 54 All as per item No 53.00 (here-in-before) above but as in skirting over 10mm thick backing coat in CM (1:3) complete all as specified and directed. 55 M&L for machine cut Kota stone slab flooring 18 to 20mm thick (minimum size 550mm x 550mm or size as directed) laid over & including screed bed or bedding layer of 20mm thick in CM (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-charge. 56 M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) for Shelves (veneering to wall) including 15mm thick plaster in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granitecomplete all as specified and as directed. 57 S&F 12mm thick toughened glass door with film of size exceeding 1.5 Sqm but not exceeding 3.00 Sqm including steel connectors, top and bottom pivots, stoppers, other fixtures required and all type of locking arrangement & brass handles fancy type 300mm long hole to hole on both side complete including taking down old unserviceable glass door complete all as specified and directed.Note:- Old glass door / partitions be removed and making good jambs, cills with the similar adjacent materials. 58 Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished of flat surface complete all as specified and directed. 59 M&L for Reinforced cement concrete (nominal mix) (1:2:4)type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors roofs landings canopies deck slab and in snelves and the like complete all as specified and directed. 60 M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 61 M&L for Plain cement concrete type B1 (1:2:4), using 20 mm graded crushed stone aggregate, 40 mm thick, as in floor and finished even and smooth using extra cement laid in alternate bay complete all as specified and directed. 62 S&F glass dividing strips of size 3mm thick and 38mm wide inserted in positioncomplete all as specified and directed. 63 M&L for 75 mm thick PCC (1:3:6) type C-2 using 40 mm graded crushedstone aggregate as inplinth protection, finished fair and evencomplete all as specified and directed by Engineer-in-charge.Note :- Plinth protection shall be laid to slope (1 in 30) in bays not exceeding 3 metre in length and joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound grade B. Cost of ceiling compund is included in the unit rate of this item complete all as spcified and directed. 64 M&L for rendering 10mm thick onfair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed. 65 M&L for rendering 15 mm thick in CM 1:4 including water proofing compound on fair face of brick or concrete surface,finished even and smooth without using extra cement complete for heigh upto G+2 story building complete all as specified and directed. 66 M&L for rendering 5mm thick in CM (1:4) as on ceiling complete all as specified and directed. 67 Supply only liquid water proofing compound ISI marked complete all as specified and directed by Engineer-in-charge 68 M&L for applying a coat oftwo component elastomeric acrylic polymer modified cementitious water proofing coating, having properties of 80 % elongation as per ASTM D412, resisting 5 bars hyrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc., complete as per manufacturers specifications andsprinkle sand at 10-15 gram per sqft for better grip with plaster complete all as specified and directed. 69 Taking up or down 15mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. 70 Taking up or down 20mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. 71 S&F 15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge 72 S&F 20 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge 73 Fixing only 15mm bore old galvanised steel water tubing including cleaning with & including new fittings and fixed complete to walls and ceilings or laid in floors in new or old position complete all as specified and directed by Engineer-in-charge.Note: GI tubing retrieved vide item No 69.00 shall be used under this item. 74 Fixing only 20mm bore old galvanised steel water tubing including cleaning with & including new fittings and fixed complete to walls and ceilings or laid in floors in new or old position complete all as specified and directed by Engineer-in-charge.Note: GI tubing retrieved vide item No 70.00 shall be used under this item. 75 Disconnecting existing tanks of capacity exc 500 ltr & not exc 1000 ltr, setting aside (or lowering if required) for repairs and cleaning & removing all scale and dirt etc, from tank and from mouths of circulating pipes and hoisting and re-fixing in same or other position complete all as specified and as directed by Engineer-in-charge. 76 S &F for rotational moulded polythelene water tanks triple layer white colour (cylindrical vertical with closed top) hoisted and fixed in position for 750 ltr. storage capacity including disconnecting and taking down old unserviceable tanks and ball valve complete all as specified and directed. 77 S&F in repair 20mm dia PTMT ball PVC valve, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Engineer-in-charge. 78 S&F 20mm dia ball brass valve, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Engineer-in-charge. 79 S&F in repair 20mm Gate valves, high pressure, with polytheene float and flynut complete, screwed for iron pipe orr brass ferrule and fixed. 80 S&F in reapir PVC water tank cover for any capacity of PVC water tank fixed with suitable bolt & nuts complee as directed. 81 S&F PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints laid in trenches orfixed to wall complete including taking down old unserviceable PVC pipe with fittings complete all as specified and directed. 82 S&F PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints laid in trenches orfixed to wall complete including taking down old unserviceable PVC pipe with fittings complete all as specified and directed. 83 S&F PVC (SWR) 75mm bore bends anyradiuscomplete all as specified and directed. 84 S&F PVC (SWR) 110mm bore bends anyradiuscomplete all as specified and directed. 85 S&F in repairs 32mm bore CP waste coupling fittings for sinks, basins with long shanks and fly nuts, flange and bedded in red cement and fixed complete all as specified and directed by Engineer-in-charge. 86 S&F in repairs 40mm bore CP waste coupling fittings for sinks, basins with long shanks and fly nuts, flange and bedded in red cement and fixed complete all as specified and directed by Engineer-in-charge. 87 S&F in repairs PVC waste pipe 32mm dia of length 0.8mm to 0.9mm fixedcomplete all as specified and directed. 88 S&F in repairs PVC urinal pipe 40mm dia of length 0.8mm to 0.9mm fixedcomplete all as specified and directed. 89 S&F in repair chromium plated shower rose with shower arm or without swivel joints including fixing to steel pipe of 100 mm size complete all as specified and directed by Engineer-in-charge. 90 S&F in repair CP Jet spray butter fly design fixed on EWC with stanless screw as approve complete all as specified and directed by Engineer-in-charge. 91 S&F in repair 450mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and directed by Engineer-in-charge. 92 S&F in repair 600mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and directed by Engineer-in-charge. 93 S&F in repair 15mm bore CP angle valve, fancy type, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-charge. 94 S&F in repair 2 way 15mm CP angle fancy type 15 mm bore high pressure screwed for iron pipe complete all as specified and directed by Engineer-in-charge. 95 S&F in repair 2 way 15mmCP fancy bib tap 15 mm bore high pressure screwed for iron pipe complete all as specified and directed by Engineer-in-charge. 96 S&F in repairs 15mm bore brass chromium plated basin mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore complete all as specified and directed by Engineer-in-charge. 97 S & F in repairfor 15mmbib tap standard of PTMT any colour screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-charge. 98 S & F in repairfor 15mmangle cock standard of PTMT any colour screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-charge. 99 S & F in repairfor 15mmPillar tap fancy typestandard of PTMT any colour screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-charge. 100 S&F in repair 15 mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge. 101 S&F in repair vitreous china squatting pan Orissa pattern, white of size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) including cast iron P or S trap, PCC filling and connection to trap and flushing pipe, antisyphonage pipe etc complete all as specified and directed by Engineer-in-charge. 102 S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device and jet spray complete all as specified & as directed by Engineer-in-charge. 103 S&F in repairs PVC EWC seat cover of any type, white colour for pedestal pan complete all as specified and directed by Engineer-in-charge. 104 S&F in repair 10 litre capacity PVC valveless symphonic action type low level flushing cistern (ISI marked) including32 mm dia PVC flush pipeconnected to water closet with inlet, ball valve, float and handle complete all as specified and directed by Engineer-in-charge. 105 S&F in repairs, vitreous China wash hand basin, white, flat back size 550 x 400mm including 15mm dia, 450 mm long HDPE PVC connection, 750 mm long 32mmbore HDPE waste down pipe including CI brackets complete all as specified and directed. 106 S&F repairs pillar taps (fancy type), of 15 mm dia long body, cast copper alloy, with capstan heads, with chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed. 107 S&F pillar taps (fancy type), of 15 mm dia long body, cast copper alloy, with capstan heads, with chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed. 108 M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coatof red oxide zinc chrome primer complete all as specified anddirected by Engineer-in-Charge. 109 M&L for preparation of steel surface already treated with primer over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. 110 M&L for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge. 111 M&L for preparation of old steel surfaces of any description or girth over 10 cm width or girth and applying one coat of synthetic enamel paint, completeall as specified and directed. 112 M&L for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, completeall as specified and directed. 113 S&F Factory made steel windows with side hung shutters including box type hinges with steel handle & steel peg stay complete withoutglazing bars, dovetailed or welded and also including painting the exposed steel surfaces with one shop coat of Zinc-Chromate primer complete all as specified and directed. 114 S&F Factory made steel windows with side hung shutters including box type hinges with steel handle & steel peg stay complete withglazing bars, dovetailed or welded and also including painting the exposed steel surfaces with one shop coat of Zinc-Chromate primer complete all as specified and directed. 115 S&F Steel ventilators, fixed type, with glazing bars complete all as specified & directed by Engineer-in-charge. 116 S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge. 117 S&F rolled mild steel as in Joist, channel, angle or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length directed) and similar work conforming to Gde E-250 (Fe 410-W) quality `A’ all as specified and as directed. 118 M&L for preparation of new plastered surface of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed. 119 M&L for preparartion of new plastered surfaces of walls and applying two coats cement base paint on walls completeall as specified and directed. 120 M&L for preparation of new plastered surfaces of ceiling and applying three coatsof white wash complete all as specified and directed. 121 M&L for preparation of old distempered surfaces of walls by washing, rubbing down and stopping of distempered and painted surfaces and treating oil and greasy spots and applying one coat of oil bound distemper oil emulsion white or tinted completeall as specified and directed. 122 M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge. 123 M&L for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge. 124 M&L for preparation of old plaster surfaces of walls and applying one coat of cement based paint on walls for height upto G+2 story bldg complete all as specified and directed. 125 M&L for complete removal and preparation of old painted surfaces of wall and applying two coat of exterior emulsion paint for height upto G+2 story bldg complete all as specified and directed. 126 S&F in repairs curtain rod, stainless steel of25mm dia with fixing brackets stop rollers etc fix complete all as specified and directed. 127 S&F in repairs mild steel Door seal for doorsupto 1000mm long and thickness not less than 1mm complete all as specified and directed. 128 S&F in repair CP Health faucet with stand fixed on wall in CP hose pipe 1 mtr length and stainless steel screw as approve complete all as specified and directed by Engineer-in-charge. 129 S&F in repairs peg set of five of stainless steel bright finished, fixed complete all as specified and directed by Engineer-in-charge. 130 M&L for bands, straps, supports or stays for rainwater, Ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and lintle hanges, large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters ; knee piece inserts; two way and three ways straps , plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed. 131 S&F in repair brass chromium plated tubular towel rail 20mm dia; D type, 600mm long between flanges fixed to plug with chromium plated brass screws including wooden or plastic cleatcomplete all as specified and directed by Engineer-in-Charge. 132 S&F in repair 600mm x 450mm beveled edge looking mirror of selected quality glass not less than 5.5mm thick, mounted on 6mm thick commercial plywood including PVC moulded framing and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engineer-in-charge. 133 S&F in repairPVC Syphon kit assembly in existing flush tank complete all as specified and directed. 134 S&F in repair PVC mirror cabinet size 350X450mm of standard size fixed to wall with PVC sleeves and steel screws complete all as specified and directed. 135 S&F in repair Glass shelf 450mm long x 100 mm wide includingbrackets fixed to wall with sleeves and screws complete all as specified and directed. 136 S&F in repair corner glass shelf of size 300X300 mm including brackets fixed to wall with pvc sleeves and stainless steel screw complete all as specified and directed. 137 S&F in repairs vitreous china urinal Half stall type, white incl CP spreader screwed for iron pipe and fixed complete including providing and fixing plugs with and including 60mm long brass screws, pointed around urinal back in cement, fixing discharge pipr, flush pipe, grating and union for discharge complete all as specified and directed by Engineer-in-charge. 138 S&F in repair stainless steel grating with or without hole 100mm bore size fixed with white cement complete all as specified and directed by Engineer-in-charge. 139 S & F 605X605 mm size of grid GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended form soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section ( not exc 1.2 m length ) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers 6 mm dia. GI (up to 1200 mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GIflat 40X 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia. 40 mm long etc complete all as spd and as directed. Incl providing and fixing coloured designer board 4 mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed by Engineer-in-charge. 140 S&F GI lay in metal ceiling system of 600 x 600mm module which includes provides and fixing C wall angle of size 20 x 30 x 20 mm of 0.5 mm thick prepainted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm c/c , suspending the main main C carrier os size 10 x 38 x 10 mm made of GI steel 0.7mm thick from the soffit with help of soffit cleat 37 x 27 x 25 x 1.6mm, rawl plugs of size 38 x 12 mm and C carrier suspension clip and main carrier bracket at 1000mm c/c. Inverted triangle shaped spring Tee having height of 24mm and width of 34 mm made of GI steel 0.45mm thick is then fixed to main C carrier and in direction to perpendicular to it at 600mm c/c with help of suspension brackets. Where ever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120gm/sqm(both side inclusive, fixing with clip in tiles into spring T with:- 141 GI metal ceiling lay in plain beveled edge global white colour tiles of size 600 x 600mm and 0.5mm thick with 25mm height, made of GI sheet having galvanizing of 100gm/sqm (Both side inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. 142 Repair of false ceiling including necessary fittings (such as wire, jointing cleat, channel or ceiling board etc required for repair) complete all as specified and directed. 143 S&F hollow corrugated shape PVC wall lining consisting of 5mm thick decorative colour PVC sheet, heavy duty as per sample approved by GE, inclusive of solvent cement and fixing and incl beading at sides on PVC frame as per specifications all as specifed complete all as specified and directed. 144 M & L for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge. 145 S&F Pre-painted galvalume aluminium zinc coating GI based plain steel ridges suitable for corrugated steel sheet 0.5mm thick of red colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screwscomplete all as specified and directed. 146 S&F 2nd class hard wood plain solid in truss, purlin, straight chowkhat and frames wrought, frame rebated on the solid, rounded or chamferred put together with glue pinned at joints etc complete all as specified and directed. 147 M&L for 75 mm thick Cement concrete type D-2, (1:4:8) using 40 mm graded stone aggregate as in sub base complete all as specified and directed. 148 M&L for Machine pressed precast conctete interlocking paver block with grey cement & pigment any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed. 149 M&L for sand filling under floors or in foundation complete all as specified and directed. 150 M&L for cement concrete (1:2:4) type B2 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railigs upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, sligtly rounded or chamfered angles and throating, as directed including necessary form work complete all as specified and directed. 151 M&L for pre-polished chequered tiles (any colour) of size 30cm x 30cm x 25mm thick, with gray cement & pigmentset, jointed and pointed in neat cement slurry in floors laid over and including 20mm screed bedding in cement mortar (1:4) complete all as specified and directed. 152 M&L for vitrified paving tiles in size of 300mm x 300mm x 10mm thick double charged digital printing laid in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade including andover of 15mm thick screed bed in CM (1:6) completed all as specified and directed.Note: Colour and sample of tiles shall beapproved by GE. 153 S&F in repairs door closer hydraulically regulated designation No. 3 universal type cast iron body suitable for door shutters of 851 to 1000mm in width and fixed complete all as specified and directed by Engineer-in-charge. 154 S&F 300mm mild steel (Helical door spring) ordinary rat tail rod pattrern springincluding roller and roller plate complete with necessary welding work complete all as specified and directed. 155 Taking down surface / concealed copper / aluminium point wiring (light, bell, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, lamp holders, pendants, sockets, regulators, tubelight fittings etc and making good disturbed surfaces with plaster on walls, floors etc complete all as specified and directed. 156 M&L for Point wiring complete with 2.5 sqmm single core FRLSH PVC insulatedcable with multi stranded copper condutor in and including PVC conduit 20mm dia and thickness not less than 1.5mm, ISI marked with all accessories for surface or concealed conduit as directed at site incl chase cutting for one light/fan point controlled by one one way switch including MS sheet sunken box concealed on wall duly painted inside and outside with one coat of red oxide primer and two coats of black bituminous paint with 3mm thick hylum brand bakelite sheet cover for fixing switches, sockets, regulators etc. alongwith 2.5 sqmm multi stranded FRLSH, PVC insulaedcopper cable as continuous earth connected to common earth and earth dolly including making good the disturbed surfaces complete all as specified and as directed. 157 All as per Sl item No 155.00 above here-in-before for light point controlled by two way switch complete all as specified and directed. 158 All as per Sl item No 155.00 above herein before but for one bell point controlled by one bell push. 159 All as per serial item No. 155.00 here-in-before but for One 3 pin 5 Amp socket outlet on independent board. 160 All as per serial item No. 155.00 here-in-before but for One 5 pin 5 Amp socket outlet on the same board with other switches. 161 M&L for point wiring with 2.5 sqmm PVC insulated, unsheathed FRLSH multistrand copper conductor cable 1100 volts grade drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all and including conduit fittings and fixing accessories 1.2mm thick sunken anodised pressed steel terminal boxes with 3.0 mm thick hylam sheet cover for mounting switches, socket etc including 2.5 Sqmm FRLSH multistrand copper conductor cable as continuous earth wire complete for one socket 16 Amp socket outlet controlled by one switch on independent board.complete all as specified and directed. 162 M&L forSub main wiring with 2 runs of 4 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLSH 1100 volts grade cable drawn through and in existing surface / recessed PVC conduit and connecting incoming/outgoing electric connections and one run of 4 Sqmmsingle core PVC insulated but unsheathed multistranded copper conductor FRLSH 1100 volts grade cableas earth conductor including taking down old unserviceable submain wiring and making good disturbed surfaces complete all as specified and directed. Note : Two runs of 4 Sqmm cable, one run of 4 Sqmm earth conductor and one run of PVC conduit of 25mm dia shall be measured and paid as one unit length. 163 M&L for Sub main wiring with 2 runs of 6 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cable drawn through and in existing surface / recessed PVC conduit and connecting incoming/outgoing electric connections and one run of 6 Sqmmsingle core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cableas earth conductor including taking down old unserviceable submain wiring and making good the disturbed surfaces complete all as specified and directed. Note: Two runs of 6 Sqmm cable, one run of 6 Sqmm earth conductor and one run of PVC conduit of 32mm dia shall be measured and paid as one unit length. 164 M&L for Sub main wiring with 2 runs of 10 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cable drawn through and in existing surface / recessed PVC conduit and connecting incoming/outgoing electric connections and one run of 10 Sqmmsingle core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cableas earth conductor including taking down old unserviceable submain wiring and making good the disturbed surfaces complete all as specified and directed. Note: Two runs of 10 Sqmm cable, one run of 10 Sqmm earth conductor and one run of PVC conduit of 32mm dia shall be measured and paid as one unit length. 165 Supply and laying in replacement of Non Metallic Rigid PVC conduit, ISI Marked, conforming to IS 9537, medium grade, size 25 mm dia including all fittings like bends, elbow reducer, junction, couplerboxes, tee bell mouth etc for protection of cables/wires complete in all respect as specified and directed. 166 Supply and laying in replacement of Non Metallic Rigid PVC conduit, ISI Marked, conforming to IS 9537, medium grade, size 20 mm dia including all fittings like bends, elbow reducer, junction, couplerboxes, tee bell mouth etc for protection of cables/wires complete in all respect as specified and directed. 167 Supply and laying in replacement of worn out PVC rigid conduit with uPVC trunking/casing caping of size 50mm x 16mm including fittings conforming to IS 14927/2001, fixed to wall/ceiling surface to cover the cable/wire complete all respect as specified and directed. 168 M&L for cutting chases, pining in making good to facing where required and pointed in CM (1:3) to ends or edges of brick wall etc and cutting chases for concealed conduit wiring etc and making good, match with existing surfaces by applying white/colour wash cutting not exc 10cm girth complete all as specified and directed. 169 S&F switch piano flush button single pole, one way 5 Amp 240 Voltcomplete all as specified and directed. 170 S&F switch piano flush button single pole, one way 15 Amp 240 Voltcomplete all as specified and directed. 171 S&F switch piano flush button single pole, two way 5 Amp 240 Voltcomplete all as specified and directed. 172 S & F Switch Bell push 5 amp single Pole230 V all as specified & directed. 173 S&F socket outlet 6 amps 5 pin flush type, 230 volts complete all as specified and directed. 174 S&F socket out let, 6 pin 5 and 15 amps multi purpose 2 in 1 flush type 230 volt complete all as specified and directed. 175 S&F in repair sheet metal enclosureSingle pole & neutral with 2 pin and earth plug and socket 20A240 Volt complete with one single pole MCB of cap 20/25 A, C series complete all as specified and directed. 176 S&F ceiling rose 63x30 mm three terminal, polycorbonate body complete all as specified and directed. 177 S&F fan regulator electronic, five step type hum free suitable control speed of fan from 0 to 100% and connectingelectrically all as required complete all as specified and directed. 178 S&F Angle / batten holder polycorbonate type body suitable for batten fitting complete all as specified and directed. 179 S&F in repair adaptor, 240 volts polycorbonate type body for proper connection to LED batten through batten holder complete all as specified and directed. 180 S&F in replacement musical door bell (having locking features) including 2 Nos, AA 1.5 volt battery for working even when no electricity suitable for 230 volts AC supply complete all as specified and directed. 181 S&F in replacement sketch fitting with decorative, wall mounting, brushed nickel finish fixture with acrylick diffuser including fixing 12 watt rechargable/invertor LED lamp, B22 base cap complete all as specified and directed. 182 S&F in replacement of LED security / street light, 45 Watt, IP - 66, Impact resistance - IK07, colour temp- 5700 K, Class I in Pressure die-cast aluminium alloy for housing (heat sink) for effective thermal management, sturdiness, excellent corrosion resistant, separate optical and control gear compartment & top opening for easy maintenance. Polyster powder coated grey after phosphochromate treatmentHigh efficiency long life LED modules with SMD LED package mounted on MCPCB. Lumen efficacy of LED >110 lm/W with PC lens to ensure better uniformity of light distribution. Powered by Built-in, Potted electronic LED driver (SMPS based constant current supply) with lower THD, Output Open Circuit protection, Phase to Phase protection, Over Voltage protection, Surge Voltage protection upto 10 kV with external SPD & other safety tests as per IS 15885 Part-2/ Sec13. Suitable for bldg/pole mounting alongwith single arm bracket OD 58 mm (max) with suitable reinforcement on wall height complete in all respect & as directed. 183 S&F in repairs MCCB, 100 Amp, 4 Pole, 36 KA, 415 volts adjustable thermal & fixed magnetic setting complete all as specified and asdirected. 184 S&F in repairs MCCB, 63 Amp, 4 Pole, 36 KA, 415 volts adjustable thermal & fixed magnetic setting complete all as specified and asdirected. 185 S&F in repairs TPN MCB, 415 volts, 10 KA, 4 Pole, 100 Amps C series complete all as specified and asdirected. 186 S&F in repairs TPN MCB, 415 volts, 10 KA, 4 Pole, 63 Amps C series complete all as specified and asdirected. 187 Supply & fixing in replacement of MCB DP, 240 Volt, 10 KA, 40 Amps, C series complete all as specified and directed. 188 Supply & fixing in replacement of MCB DP, 240 Volt, 10 KA, 63 Amps, C series complete all as specified and directed. 189 Supply & fixing in repair LED constant driver suitable for 2 x 2 LED luminaries of wattage from 30 to 40 watt, 25 to 42 volts DC including fault detection, soldering and testing complete all as specified and directed. 190 Supply & fixing in repair LED constant driver suitable for LED batten 18/20 watt, input voltage range - 110 to 280 volts AC, output voltage range 40 to 75 volts DC including fault detection, soldering and testing complete all as specified and directed. 191 S&F in replacement surface and wall mounted 20 watt LED batten, PVC housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete all as specified and directed. 192 S&F in replacement 10W integrated LED bulk head luminaire environment friendly, ultra modern, energy saving, surface mounted decorative oval bulk head with LED light, complete all as specified and directed. 193 S&F in replacement surface and wall mounted 10 watt LED batten, PVC housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete all as specified and directed. 194 Supply & fixing in replacement ceiling light with 36W Watt, 6000 K, slim LED panel 2 x 2 LED panel for recessed on ceiling) dust-free installation with high brightness LEDs for glare-free homogenous illumination with driver and all other connected accessories complete all as specified and directed. 195 Supply & fixing in replacement sheet metal enclosure MCB distribution board triple pole & neutral 415 volts 4 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. 196 Supply & fixing in replacement sheet metal enclosure MCB distribution board single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. 197 Supply & fixing in replacement sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. 198 Supply & fixing in replacement of MCB single pole 240 volt any rating from 6 to 32 amps, B series with rupturing capacity 10 KA complete all as specified and directed. 199 S & F modular type6A one way SP switch 1 moduleconfirming to IS: 3854-1997 with finger proof terminal complete all as specified and directed. 200 S & F modular type 2/3 pin 6 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed. 201 S & F modular type16 A one way SP switch 1 module confirming to IS: 3854-1997 with fingure proof terminal complete all as specified and directed. 202 S & F modular type 2/3 pin 16 Amps socket 2 module conforming toIS: 1293-2005 complete all as specified and directed. 203 S&F modular type 3/5 pin socket with one single pole MCB 20 Amp 230 Volts concealed in wall complete all as specified and directed. 204 S & F modular type 120W step fan regulator of 2 module size conformng to IS: 11037-1984 complete all as specified and directed. 205 S & F in repair wall lamp, mettalic with chrome finish, diffused glass with 5 to 9 watt LED bulb complete all as specified and directed. 206 S & F in repair shock safe plug 16A 30 Ma PRCD plug top, 220 V, equipped with an auto trip feature which shuts off detects any current leakage, fuse must be used as a back up protection for over load 6IEC:61540 recommeded complete all as specified and directed. 207 Supply and fixing in replacement exhaust fans 300 mm sweep metallic body, heavy duty, four blade, double ball bearing, 1400 RPM, minimum air delivery discharge 1710 CMH suitable for SP, 230/250V, 50 Hz AC supply with protective bird guard with louver shutters including grouting of frame in walland connecting with and including 3 run 1.5 Sq mm single core, PVC insulated but unsheathered FRLSH multistranded copper conductors cable from ceiling rose to exhaust fan complete all as specified and directed.Note : Old unserviceable exhaust fan shall be deposited in AGE E/M store yard. 208 S&F in replacement Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230 V, 5 Hz, RPM 1200, copper winding of sweep 300mm complete all as specified and directed.Note : Old unserviceable exhasut fan shall be deposited in AGE E/M store yard. 209 Supply & fixing in replacement of LED Bollard light 10watt, IP 65 aesthetically designed landscape luminaire for diffused lighting suitable for architectural outdoor lighting typically giving off light from all sides best suitable to illuminate walkways, steps or pathways complete all as specified and directed. 210 Supply & fixing in replacement LED profile strip light with 120 LED per meter for uniform light complete all as specified and directed. 211 Supply & fixing in replacement adaptor for LED profile strip light as per site requirement complete all as specified and directed.
