|
| 1 | Boring with hydraulic piling rigs with power units, providing andinstalling cast in situ single under reamed piles of specified diameterand length below pile cap in M-25 cement concrete, to carry asafeworking load not less than specified, excluding the cost of steelreinforcement but including the cost of boring with bentonite solutionand the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) 400 mm Dia. |
| 2 | Earth work inexacavationin trenches for foundations and for pipes cables etc.inordinary soil( loan clay orsand)including lift upto 1.5 mand leadup to 30m.&including filling watering& ramming of excavated earth in to trenchesor in to the space betweenthe building & the sides of foundation trenchesorinto the plinthandremoval&disposal of surplusexcavated earthas directed by the Engineer i/c upto a distance of 30 m from the foundation trenches. |
| 3 | Filling of earth in plinth under floor including watering ,ramming , consolidating & dressing complete including lead upto 30 m . & lift upto 1.5 m & including of cost. Carted up to5 km |
| 4 | Providing of sand filling in plinth under floor including watering ,ramming, consolidating anddressing complete including supply of all material labour T&P etc. required for proper completion of the work.lead upto 50 m. and lift upto 1.5m. and including cost of sand. |
| 5 | Providing and layingin cement concrete 1:4:8 (1 cement :4 coarse sand{FM 2.20-3.60} : stone ballast of 40 mm nominal size)and curing complete,including supply of all material labour T&P etc. required for proper completion of the work, in foundation and floors. |
| 6 | Providing and injecting chemical emulsionfor preconstructional antitermite treatment andcreatinga chemical barrier underand alroundthe column pits wall trenches basement excavation top surface if plinth filling junctionofwall and floor, alongthe the external perimeter of binding expansionjoints, surrounding ofpipes andconduits etc, complete (plinth area shall be measured as per I.S.6313(PartII 1981)Alderine emulsifiable concentrate or anyotherapproved materialsuch as Heptrachlor or chordancewill be used. Therateofapplicationofchemical emulsion shallbe asfollows : (1)Treatment for masonary & foundation 5 liters per/100 sqm. (2) Back fill inimmediate contact with foundation 7.5 liters/100sqm (3) Treatment of top surfaceof plinth filling 5 liters/100 sqm (4)Treatmentjunction of wallandthe floor 7.5 liters /100 sqm (5)Treatmentofsoilalong external perimeter of building 7.5liters/100sqm. (6) Treatment of soil under apronalong external perimter 5 liters/100 sqm. Chapter 8 (1) |
| 7 | R.C.C. workwith cement, approved coarse sandand2 cm. (3/4\") guageapproved stone gritin the proportion of (1:1.5:3)(1cement :1.5coarse sand( FM2.20-3.60) :3 stone aggregate20mm)inplinth band excludingsupply of reinforcement and its bending but including its fixing in position and binding with 24 B W.G.G.I. bindingwire and including necessary centering and shuttering etc.and also including supply of all materials,labour andtools andplants etc, required for proper completion of the works. |
| 8 | R.C.C. workwith cement, approved coarse sandand2 cm. (3/4\") guageapproved stone gritin the proportion of (1:1.5:3)(1cement :1.5coarse sand( FM2.20-3.60) :3 stone aggregate20mm)incolumns excludingsupply of reinforcement and its bending but including its fixing in position and binding with 24 B W.G.G.I. bindingwire and including necessary centering and shuttering etc.and also including supply of all materials,labour andtools andplants etc, required for proper completion of the works. |
| 9 | R.C.C. workwith cement, approved coarse sandand2 cm. (3/4\") guageapproved stone gritin the proportion of (1:1.5:3)(1cement :1.5coarse sand( FM2.20-3.60) :3 stone aggregate20mm)inhavier T-beam excludingsupply of reinforcement and its bending but including its fixing in position and binding with 24 B W.G.G.I. bindingwire and including necessary centering and shuttering etc.and also including supply of all materials,labour andtools andplants etc, required for proper completion of the works. |
| 10 | R.C.C. workwith cement, approved coarse sandand2 cm. (3/4\") guageapproved stone gritin the proportion of (1:1.5:3)(1cement :1.5coarse sand( FM2.20-3.60) :3 stone aggregate20mm)inlintel band excludingsupply of reinforcement and its bending but including its fixing in position and binding with 24 B W.G.G.I. bindingwire and including necessary centering and shuttering etc.and also including supply of all materials,labour andtools andplants etc, required for proper completion of the works. |
| 11 | R.C.C. workwith cement, approved coarse sandand2 cm. (3/4\") guageapproved stone gritin the proportion of (1:1.5:3)(1cement :1.5coarse sand( FM2.20-3.60) :3 stone aggregate20mm)inT-BEAMslabs excludingsupply of reinforcement and its bending but including its fixing in position and binding with 24 B W.G.G.I. bindingwire and including necessary centering and shuttering etc.and also including supply of all materials,labour andtools andplants etc, required for proper completion of the works. |
| 12 | Centering and shuttering including strutting, propping etc. and removalof form for. Suspended floors, roofs, landings, balconies and accessplatform |
| 13 | Centering and shuttering including strutting, propping etc. and removalof form for. Lintels, beams, plinth beams, girders, bressumers andcantilevers |
| 14 | Centering and shuttering including strutting, propping etc. and removalof form for. Columns, Pillars, Piers, Abutments, Posts and Struts |
| 15 | Class 150 brick work in1:6cement and coarsesandof ( FM 1.5-2.20) modulus mortar infoundation and plinth including supply ofall materials,labourand tools and plants etc.requiredforpropercompletion of the work. |
| 16 | Class 150 brick work for one brick thick wall in1:4 cement and coarsesandof ( FM 1.5-2.20)mortar in super-structureaboveplinth levelup to floor two level ( up to two storeys ) including necessary cutting and mouldingofbrickworkas requiredandalsoincludinghoney combed brick work in thickness of wall more than 12cms. |
| 17 | Same As above item No. 17but in1:3 cement and coarse sand (FM 1.50-2.20) mortar in superstructure for wall thickness 12 cms & below. S.I. No.307+309+310a |
| 18 | Providing and laying\"brick coba\" 12mm thick laid with M.150 class brick bat coba 7.50cm. Thick with gap of 15mm to each other. over 20mm. Thick base of cement morter 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with aerelic cement concrete waterproofing compound filed gaps of coba & top of coba mortar mixed with water proofing compoond. in 1:4 cement & coarse & morter finished smooth & top mashed false square 30cmX30cm. & side wall parapet shall be mono tythic plaster wall up to 30cm.higher & junction & corner shall be rounded by brick ballast cement and coarse sand masonary coba with top finished mixed with acetic water proofing compound @ 2% by weight & including S/o all material, labour, T & P etc. com.for proper completion of work. CHAPTER 11 NEW ITEM |
| 19 | Mild steel or iron in plain work such asreinforced concrete or reinforced, brick work(whennot includedin anover all rates )wroughttorequired shape as necessary including bending for proper completion of thework andincluding supply of steel itswastage bendhooks andauthorisedover lappingshallbe measured upto floor two level. |
| 20 | 12 mm cement plasterinsingle coat on fair sideofsingle orhalfbrickwall for interior plastering up to floor twolevelincludinginternalrounded angles not exceeding 80mm ingirth nd finshed even and smooth.(1)1 cement:6 C sand (FM 1.50-1.75) |
| 21 | 12mm cement plaster in single coat on of stairs upto floor two level. (Analysis rate)rough side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or roundedangles not exceeding 80mm in girth andfinished even and smooth no extra for mixing any additive. (1)1 cement :4 C sand (FM 1.50-1.75) |
| 22 | Providing and laying vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS :15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including groutingthe joints with white cement and matching pigmentsetc., complete. SIZE 600MM X 600MM |
| 23 | Providing and laying Vitrified tiles in different sizes(thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, cement: 3 coarse sand), of approved make,in all colours &shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3(1 cement:3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete SIZE 600MM X 600MMskirting |
| 24 | Supply & fixing 6 mm thick china white glazed tiles in flooring or in skirting or Dado laid with 1:3cement & approved course sand mortar finished with white cement slurry jointing & polishing complete including supply of all materials,labour & tools & plants etc. required for proper completion of work. |
| 25 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 26 | P/F white cement based putty of average thickness 1mm ,of app. Brand and manufacturer over the plastered wall surface to prepare the surface even and smooth complete. |
| 27 | Distempering (Two coat) with oilbound distemper of approved brand and manufacture of required shade on undercorted of wall surface to give an even shade overand including a priming coat with cement primer of approvedbrand and manufacture such asBerger, J & N Shalimar Paints afterthroughly brushing the surface free from mortar dropping and other foreign matter and also including prepairing the surface even with Plaster of Paris or approved synthetic material and sand paperedsmooth including cost of all materials labour T&P. |
| 28 | Finishing walls with Acrylic Smooth exterior paint of required shade :13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqmover and including priming coat of exterior primer applied@ 2.20 kg/10 sqm) |
| 29 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required : |
| 30 | Providing & fixing white vitreous china wash basin with C.I. brackets painted white, 15mm C.P. brass pillar taps, C.P. brass chain with rubber plug, 32mmC.P. brass waste of standard pattern including cutting & making good the walls wherever required.White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow including operated levers |
| 31 | Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. a) 32mm dia |
| 32 | Providing & fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick asbestos cement sheet ground fixed to wooden cleats with C.P. brass screws and washers. |
| 33 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting andmaking good the walls and floors wherever required One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 34 | Providing & fixing PTMT towl rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fitting arrangement of approved quality and colour. 600 mm. long towl rail length of 645 mm. width 78 mm. and effective height of 88 mm, weighing not less than 190 gms. |
| 35 | Providing and fixing PTMT Liquid soap container 109 mm wide ,125 mm high and 112 mm distance from wall of standerd shape with bracket of the same material with snap fittings of approved quality and colour weighing not less than 105 gms |
| 36 | Providing and fixing C.P. brass Two-way angle valve for EWC points & for fixing Ablution Health Fauct of approved quality conforming to IS:8931. 15 mm nominal bore |
| 37 | Providing & fixing on wall face PVC vent pipes including jointing with seal ring.a) 110mm dia PVC pipe. |
| 38 | Providing & fixing on wall face PVC vent pipes including jointing with seal ring. b)90mm diaPVC pipe. |
| 39 | Providing & fixing M.S. holder bat clamps of approved design to sand cast iron/centrifugally cast (Spun) iron S & S pipe embeded in & including cement concrete blocks 10x10x10cm. of 1:2:4 mix (1 cement: 2 coarse : 4 graded stone aggregate 20mm nominal size).Including cost of cutting holes & making good the walls etc.a) for 100mm dia pipe. |
| 40 | Providing & fixing M.S. holder bat clamps of approved design to sand cast iron/centrifugally cast (Spun) iron S & S pipe embeded in & including cement concrete blocks 10x10x10cm. of 1:2:4 mix (1 cement: 2 coarse : 4 graded stone aggregate 20mm nominal size).Including cost of cutting holes & making good the walls etc.b) for 75mm dia pipe |
| 41 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard designa) 150X100 mm |
| 42 | Providing and fixing plain PVC sanitary bend. a) 100 mm |
| 43 | Providing and fixing plain PVC sanitary bend. b) 75 mm |
| 44 | Providing & fixing 32MM G.I. Pipes complete with G.I Fittings & clamps i/c cutting & making good the walls etc. |
| 45 | P/F Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stablity for hot and cold water supplyincluding all CPVC plain and brass threaded fittings . . This includes jointing of pippes and fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Eng. I/C. Exposed on wall a) 25mm dia nominal bore (medium duty) |
| 46 | P/F Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stablity for hot and cold water supplyincluding all CPVC plain and brass threaded fittings . . This includes jointing of pippes and fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Eng. I/C. Exposed on wall b) 32mm dia nominal bore (medium duty) |
| 47 | P/F Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stablity for hot and cold water supplyincluding all CPVC plain and brass threaded fittings . . This includes jointing of pippes and fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Eng. I/C. Exposed on wall c) 40mm dia nominal bore (medium duty) |
| 48 | P/F Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stablity for hot and cold water supplyincluding all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00 mt. spacing . This includes jointing of pippes and fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Eng. I/C.CONCEALEDwork including cutting ,chases and making good the wall etc. a)20mm dia nominal bore |
| 49 | Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions. a) 15mm nominal bore |
| 50 | Providing & fixing CP brass bib cock of approved quality conforming to IS 8931a) 15mm nominal bore |
| 51 | Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. a) 15mm nominal bore |
| 52 | Providing and fixing C.P brass shower rose with 15 or 20 mm inlet 100 mm diameter |
| 53 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 54 | Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m.including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m.a) Pipes 80mm to 300mm diameter. |
| 55 | Providing, laying and joining glazed stone ware pipesheavy duty pipes grade \"A\"with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.a) 100mm diameter |
| 56 | Providing, laying and joining glazed stone ware pipesheavy duty pipes grade \"A\"with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. b) 150mm diameter |
| 57 | Constructing brick masonry manhole with 75 class designation F.P.S. bricks in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand: 4graded stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix (1 cement :4coarse sand: 8 graded stone aggregate 40mm nominal size) inside plasstering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design. a) Inside size 90x80 cm & 45 cm deep including C.I. cover with frame (light duty) total wt. of cover & frame to be not less than 38 Kg (wt. of cover 23 Kg & wt. of frame 15 Kg |
| 58 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm drybrick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5 |
| 59 | Wiring point for light with 1.5 sq.mm.FRLSHPVCinsulated multistrand single core copper conductor cable in PVC conduit with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit,GP Box , piano type switch & ceiling rose/angle/batten holder on 3mm thickphenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash. |
| 60 | Wiring point for two ways light with 1.5 sq. mm. F.R. PVCinsulated multistrand single core copper conductor cable in PVC conduit with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit, GP Box andtwo number two waypiano type switches & ceiling rose / angle / batten holder on 3 mm thick phanolic laminated backelite sheet etc., complete in allrespect,as directed, including matching colour wash. |
| 61 | Wiring point for fan / fresh air fan (light duty exhaust fan) with 1.5 sq.mm.FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit,GP Box , piano type switch & ceiling rose on 3 mm. thick backelite sheet etc., complete in all respect including matching colour wash. |
| 62 | Wiringpointforplugwith 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit and piano typeswitch and socket etc., complete in all respect including matching colour wash. |
| 63 | Wiring point for exhaustfan with 1.5 sq. mm.FRLSHPVC insulated multistrand single core copper conductor cable in PVC conduit with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit,GP Box , 15A piano type switch& ceiling rose on 3 mm thick phenolic laminated backelite sheet etc., complete in all respect including matching colour wash. |
| 64 | Same asin item 148, but 25mm dia 16 SWG (1.5 mm)thickrigid steel conduit. |
| 65 | Same as in item 174(B) but for plug point with 5 Amp flush typeswitch and 3 pin socket and earth continuity wire of1.5 sq.mm. FRLSH PVC insulated multi strand copperconductor cable in PVC conduit. |
| 66 | Add for light / fan points with modular type switch in place of piano type switch. |
| 67 | Add for 2 way light point with modular switches in place of piano type switches. |
| 68 | Add for plug point with modular switch & socket in place of piano type switch & socket. |
| 69 | Add for HPMV/Exhaust fan point with modular type switch in place of piano type switch. |
| 70 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections butexcluding modular plate etc. as required.Telephone socket outlet |
| 71 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm) |
| 72 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100mmX75mm) |
| 73 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 4 Module (125mmX75mm) |
| 74 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 8 Module (125mmX125mm) |
| 75 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 76 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair |
| 77 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. |
| 78 | Supply and wiring of submain with two number2.5sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2mm thick) PVC conduit with 1 nos. 1.5 sq. mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable as earth continuity wire drawn inside the conduit complete in all respect. |
| 79 | Supply and wiring of submain withtwo number 4 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2 mm thick) PVC conduit with one no. 2.5 sq. mm.FRLSH PVCinsulatedmultistrand copper conductor cable as earth continuity wire drawn in conduit. |
| 80 | Supply and wiring of submain withtwo number 6 sq. mm. FRLSH PVC insulated 1100 V grade multistrand single core aluminium conductor cable in 25 mm dia heavy duty (2 mm thick)PVC conduit with one number 4 sq. mm. FRLSHPVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. |
| 81 | Supply and wiring of4 number 10 sq. mm. FRLSH PVCinsulated 1100 V grade multistrand single core copper conductor cable in heavy duty (2 mm thick) PVC conduit with 2 nos 6 sq.mm. FRLSH PVC insulated copper conductor cable as earth continuity wire drawn in conduit. |
| 82 | Supply and fixing ofrecess/Surface/Pendentmounting round6 Watt 8 Watt LED Down Lighter having Powder coateddie cast aluminiumhousing withheat sink, diffuser/ Reflectorand driver set complete in all respect. CAT- AAA |
| 83 | Supply and fixing ofrecess/ Surface/ Pendentmounting round 25 Watt LED Down Lighter having Powder coateddie cast aluminium housing withheat sink, diffuser/ Reflector and driver set complete in all respect. CAT- AAA |
| 84 | Supply and fixing of batten / angleholder complete in all respect. |
| 85 | Supply and fixing ofLED Tube Light with batten suitable for up to 1 X 22 watt LED tube light fittingincluding tube on Surface complete in all respect.CAT- AAA |
| 86 | Supplyandlayingof aluminiumconductorPVCinsulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 16 sq. mm 4 core |
| 87 | Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring ofthe cable shall be properly connected with the earth as per direction of Engineer-Incharge. 6 sq. mm 2 core |
| 88 | Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring ofthe cable shall be properly connected with the earth as per direction of Engineer-Incharge. 10 sq. mm 4 core |
| 89 | Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. 6 sq. mm |
| 90 | Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. 10 sq. mm |
| 91 | Supply and burying of 600mm x 600mm x 6mm G.I. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe and funnel for watering and one earthing lead oftwo no. 8 to 10 SWG GI wire in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respect. |
| 92 | Supply and laying of 25mm x 3mm G.I. strip from earth electrode directly in the ground as required complete in all respect. |
| 93 | S&F surface/flush mounting 8ways SPN distribution board with additional metal door without MCB complete in all respect, as directedbyEngineer in charge. Cat-A |
| 94 | S & F surface/Flush mounting 6ways TPN distribution board with additional metal doorwithout MCB complete in all respect, as directed at site byEngineer in charge. Cat-A |
| 95 | S&F of6 Amp. to 32Amp. DP MCB (10 KA) C CurveCat-A |
| 96 | S&F of 6 Amp. to 32Amp. 3 pole MCB (10 KA) C Curve Cat-A |
| 97 | S & F surface/Flush mounting 4waysV TPN distribution board without additional Door without MCB complete in all respect, as directed at site byEngineer in charge. Cat-A |
| 98 | S&F of 80to 100 Amp4 pole MCCB (16 KA)Thermal Magnetic release |
| 99 | Erection and testing of ceiling fan and regulator for room height upto 3.5 metres including supply of 3mm thick G.I.Pipe19mm dia. Duly painted, complete in all respect. |
| 100 | Erection and testing of exhaust fan on the existing hole with suitable size of rag bolts, nuts and washers etc., complete in all respect. |
| 101 | Supply and fixing of 16 SWG M.S. drum with luvers duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respect. |
| 102 | Supply and fixing of power plug with 20 Amp./250 voltflush type modular switch and 5 pin 20 A/250 volt flush type universal modular socketswitch on concealed M.S boxincluding supply of all material, labour T&P etc. required for proper completion of work. |
| 103 | Supply and fixing hexagonal Round G.P.fan box approved make made up of 1.0 mm thickISI Marked G.P.sheet spot welded Four to Eightholes for pipe entryof the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made upper & lower cover duly screwed. Fixing with wiring conduit laid in the R.C.C. roof before concretingalongwith supply of all material, labour, T&P etc. required for proper completion of the work. |
| 104 | Supply and fixing of electronic fan regulator( Modular) 120-280 V. ISI marked, on the existing switch board including making connections, required material, labour T&P etc. for proper completion of work to the satisfaction of Engineer in charge of work. |
| 105 | Supply of 1200mm sweep copper wound fan having double ball bearing energy efficient having power consuption of 70 to 75W fan making of sheet metal similar to Crompton Neo Breeze or equivalent. |
| 106 | Supplyandlayingof aluminiumconductorPVCinsulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 6 sq. mm 4 core |
| 107 | Supplyandlayingof aluminiumconductorPVCinsulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 16 sq. mm 4 core |
| 108 | Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring ofthe cable shall be properly connected with the earth as per direction of Engineer-Incharge.6 sq. mm 4 core |
| 109 | Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring ofthe cable shall be properly connected with the earth as per direction of Engineer-Incharge. 16 sq. mm 4 core |
| 110 | Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge.6 sq. mm |
| 111 | Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. 16 sq. mm |
| 112 | Supply & fixing of 7 mtr GI Octagonal Pole of approved make(top dia 70mm, Bottom dia 130mm and base plate 12mm thik) having 3mm thikness with single arm bracket (1 Mtr length) on RCC foundationincluding the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect. |
| 113 | Supply and fixing ofLED Street light Fittinghaving die cast aluminium body and diffuser with driver set suitable for 30Watt. to 40 Watt. Confirming to IP 66protection complete in all respect. CAT- AAA |
| 114 | Supply and burying of 40mm dia x 4.5 metres long G.I. Pipe vertically for earthing having 12mm dia. Holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No. 6 to 8SWG GI wire in G.I. Pipe up to appron (and from appron to switch board the cost of G.I. wire and pipe will be extra) upto switch board, 30cm square C.I. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respects as per drawing. |
| 115 | Supply and fixing of fire extinguisher, ABC Type 6.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 116 | Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity(ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 117 | Transportation Charges of drilling equipment including assembly and other material as required. |
| 118 | Drilling of 450 to 675 mm dia by rotary machine |
| 119 | Supply & laying of 150mm dia M.S housing pipe (7.2 mm thick)Tata/ Jindal |
| 120 | Supply & laying of 100mm dia M.S blind pipe (7.2 mm thick)Tata/ Jindal |
| 121 | Supply & laying of 100mm dia M.S slotted pipe (7.2 mm thick)Tata/ Jindal |
| 122 | Supply & fixing of 150mm dia UPVCRing |
| 123 | Supply & fixing of 100mm dia UPVCRing |
| 124 | Supply & fixing Bail plug 100 mm dia UPVC |
| 125 | Supply & fixing Well Cap 200 mm dia UPVC |
| 126 | Supply & fixing Housing clamp 100 mm diaUPVC, |
| 127 | Supply & filing of Pee gravel 1.6 mm to 2 mm in side of bore after lower and development as required as per direction of E/I. |
| 128 | Development by O.P unit including transportation. |
| 129 | Well logging charges |
| 130 | PUMPING SET KSB make submersible pump set suitable for installation in bore well of min 150 mm inner dia preferably more and having under noted specifications.TYPE UQD 182/10 + 6 UMA I/H 150/22(S/D)+2.0HPCapacity 1400LPH Total Head 92M No of stages 6 Max OD of the pump set 150mm size of discharges out let 3”Speed in RPM2900 RPM H. P. of Motor 5.5 KW/ 5 HP Method of starting star delta supplyof voltage 400 V +3%3 phase The pumping set shall be comprise ( a ) Built in non-return valve ( b ) Sixstages bowl assembly with bronze impellers and S. S. impeller shaft etc. ( c ) 2.0 HP 2900 RPM sub mersible electric motor suitable for Star/Delta starting with 3RM cable 2 x 3 x 4 sq mm |
| 131 | Supply and fixing of finolex of copper cable ISI marked submersible cable of size 1 x 3 x 4 sq mm |
| 132 | Supply of controlpanel board cubical type wall mounted vermin proof with internal wiring duly enameled painted for mechanically finished having L&T or equivalent make switch fuse unit with HRCfuses, ammeter, voltmeter, selector switch phase indication lamp with bulb (instrument fuses, power capacitor, single phase preventercomplete set with supply of L&T Jyoti or equivalent Air break Star-Delta motor starter suitable for above pump set. |
| 133 | Supply of 80mm dia M.S. column pipe of class \"C\" both and socketed with heavy sockets in 3/6 meter length and one end flanged complete with interlocking arrangements. |
| 134 | Supply of 80mm dia M.S.column pipe clamps with nut bolts packing etc. |
| 135 | Supply of 80mm dia UPVC. double flanged ISI mark reflex valve of upadhya or equ. Make |
| 136 | Supply of 80mm dia UPVC double flanged ISI mark sluice valve with hand wheel of upadhya or equ. Make. |
| 137 | Supply of UPVC. double flanged bend of 80 mm dia i/c cost of material and labour. |
| 138 | Supply of 80mm dia UPVC. tee heavy quality i/c cost of material. |
| 139 | Supply of Guru/Fiibing or equivalent make pressure gauge. |
| 140 | Supply of steel wire rope of 1/2\" size |
| 141 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50. |
| 142 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 143 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 150 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 144 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate |
| 145 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 146 | Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars( 2019) |
| 147 | Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 12 mm cement plaster |
| 148 | Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar |
| 149 | Providing and fixing soil, waste and vent pipes : 100 mm diameter :Sand cast iron S&S pipe as per IS: 1729 |
| 150 | Providing and fixing terminal guard : 75 mm Sand cast iron S&S as per IS - 1729 |
| 151 | 455x610 mm rectangular C.I. cover (medium duty) the weight of the cover to be not less than 23 kg |
| 152 | Providing and fixing SW TEE 200X200X100 |
