Tender For Necessary Repair Work In Court Complex Sawai Madhopur., madhopur-Rajasthan

Tender For Necessary Repair Work In Court Complex Sawai Madhopur.; 1 Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead With cement mortar 1 :4 ( 1 cement : 4 coarse sand) 2 Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete 3 Old Plastered Surface (two or more coats) 4 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: 5 Newwork(twoormorecoats)overandincludingscrappingandprimingcoatwithcement primer. 6 Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compoundconsisting of applying : 7 after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound@ 0.253 kg/sqm. 8 laying secondlayer of Fiber glass clothwhen the first layer is still green. Overlaps of joints of fiber cloth should not be less than 10 cm . 9 Third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289kg/sqm mixed with water proffing cement compound@ 0.670kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around 10 fourth and final layer of brick tiling ‘with cement mortar or any other approved protective coarse. (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured 11 Repair of existing steel glazed doors, windows and ventilator, MS sheet door, garge doors, compound wall gates etc. by welding drilling complete include. Cost of welding rods and hire charge of welding meachine and TP etc complete 12 Renewing glass panes,with putty and nails wherever necessary 13 Float glass panes of thickness 4 mm 14 Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing upto any pitch including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% Ultra-voilet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall confoim to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 15 2.0mm thick (Wt. 3.3 Kg./Mtr. Sq.) 16 Providing & Fixing Premium Quality white glazed vitreous china Sanitary Wares (IS:2556 Mark) of approved make as per direction of Engineer-in-charge including cutting and making good the wall and floor. 17 W.C. orissa pan with 100 mm vitreous china P or S trap (Size 580x440 mm.) 18 P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball (IS: 1703 mark) complete including cutting and making good the wall: 19 PVC with PVCbend as per IS : 7231 . 20 P& F waste Pipe with all fitting 21 P.V.C with C.Pnut 32 mm 22 P& F waste Coulping with fittings of approved quality /make: 23 C.P Brass 32 mm dia 24 P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. 25 P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors: 26 Exposed on wall 27 15 mm dia nominal bore 28 B Class 29 20mm dia nominal bore 30 B Class 31 P & F Pilllar Cocks (IS :8931 : 1993 Mark) of superior quality and approved make: 32 C.P. Pillar cock, 15 mm dia nominal bore 33 P & F Pilllar Cocks (IS :8931 : 1993 Mark) of superior quality and approved make: 34 C.P. Pillar cock, high-neck, 15 mm nominal bore. 35 P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: 36 C.P. Brass bib cock,15mm nominal bore. 37 P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. 38 ---do--- with 37 cm long pipe and nut. 39 P & F Ball Cock (IS :1703 Mark) with Rod& P.V.C. Ball complete : 40 Brass wt. Not less than 300 gm,15mm. 41 P & F Stop Cock(IS :8931 Mark),superior quality & ofapproved make: 42 (-do-) 750 gm. 20 mm nominal bore. 43 Providing and fixing premium quality Two way Bib cock 15mmwith wall flange complete as per sample approved by Engineer in charge 44 P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 45 110 mm dia 46 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: 47 Coupler (socket) 48 110mm dia 49 Bend 87 .5 50 110mm dia 51 Pipe Clip 52 110mm dia 53 Providing and fixing superior quality PVC Tank Cover complete as per approved by Engineer In Charge 54 Above 500 Lt. capacity 55 Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. 56 Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 57 Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide

INR 500 /-

INR 2.58 Lakhs /-