Tender For Provision Of 2 Single Officers Accommodation Under Ge Dehradun.; 1 Excavation in trenches in any type of soil, n exc 1.5m wide and n exc 1.5m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out complete all as specified and directed. 2 M&L for PCC 1;4:8 type D-2 (40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed. 3 M & L for RCC M-25 Design mix{ using 20 mm graded stone aggregate) in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc and mass concrete complete all as specified and directed. 4 M&L for RCC M-25 Design mix { using 20 mm graded stone aggregate) in columns, pillars, piers, posts and struts complete all as specified and directed. 5 M&L for RCC M-25 Design mix { using 20 mm graded stone aggregate) in beams,cantilevers,wall bends, bressummers, lintels over 1.5m span complete all as specified and directed. 6 M&L for RCC M-25 Design mix { using 20 mm graded stone aggregate) in Chajjacomplete all as specified and directed. 7 M&L for Mild steel TMTbars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified 8 Ditto as per item No 7 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed. 9 Use and waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed. 10 Use & waste of formwork to sides of pillers, posts, struts, piers, columns and stanchions etc for fair finished surfaces of concrete complete all as specified and directed. 11 Use and waste for Formwork to sides and soffits of floor or roof beams, wall bend beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed. 12 Use & waste of formwork to slab, chajjas,etc for fair finished surfaces of concrete complete all as specified and directed. 13 M&L for formwork flat rough finished to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide. (Where RCC/PCC band in walls, spanning and opening ccomplete all as specified and directed. 14 M&L for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed. 15 M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified and directed. 16 M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed. 17 M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed. 18 M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed. 19 M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in 1:6 complete all as specified and directed. 20 M&L for Brickwork with sub-class `B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed. 21 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified 22 Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting pointcomplete all as specified 23 S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, staging for water tanks, gusset plates etc. conforming Fe-290 (Gde E-165) complete all as specified and as directed. 24 S & F mild steel work as in main and cross beam, hip and jack rafters, purlins etc. fixed with angle cleat or other connecting plate complete confirming to Fe – 410-O or Fe – 310-Ocomplete all as specified and directed. 25 S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to walls/chajja covering etc fixed with self tapping screws complete all as specified and directed. 26 S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof ridge /covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. 27 M&L for providing false ceiling with Everest Fibre Cement Designer tile Ivory painted (High pressure steam cured) of 6mm thickness (as per IS: 14862) of size 595 x 595 mm and any one of the design (Ocean, lake & hill, cascade or electra ) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main T runner with suitably spaced joints to get required length and 15 x 32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross T of size 15 x 32 mm made of 0.30 mm sheet, 1200 mm long spaced between main T at600 mm c/cto form a grid of 1200 x 600 mm and secondary cross T of length 600 mm and size 15 x 32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200 x 600 mm panel to form grids of 600 x 600 mm and wall angle of size 15 x 20mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including, required cutting/making , opening for services like diffusers, grills, light fittings, fixture, smoke detectors etc.Main Trunners to besuspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3 mmdia with galvanised butterfly level clips, spaced at 1200 mm c/c along centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/Sqm, complete all as specified and as directed by Engr-in-Charge. 28 M&L for 15 mm thick rendering in cement mortar 1:4 on on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. 29 M &L 15 mm thick rendering in cement mortar (1:6) on fair faces of brick work finished even and smoothwithout using extra cement complete all as specified and directed. 30 M&L for preparation of wall and applying interior grade wall care putty 1 mm thick to make the surface smooth complete all as specified and directed. 31 M&L for preparation of wall and applying exterior grade wall care putty 1 mm thick to make the surface smooth complete all as specified and directed. 32 M&L for applying two coat of oil bound distemper on prepared surface of wallcomplete all as specified and directed. 33 M&L preparation of new plastered surfaces of external wall and application two coats of 1st quality exterior emulsion weather coatpaintsover a coat of alkali resistant priming paint complete all as specified and directed. 34 S&F of power coated ventilator fixed type and frame made with aluminium section with and including partly glass and partly stainless steel wire mesh and including aluminium grill of aperture not more than 40 sqcm (as specified below), aluminium sections shall be of size as given below including taking down old window/ventilator etc complete all as specified and directed by Engineer in Charge. Frame : 44.5 x 44.5 mm x 1.98 mm thick including 5mm thick frosted in glassfixed with rubber gasket with aluminium beading and stainless steel wire mesh of 0.63 mm nominal dia wire and average width of aperture 1.40 mm. Note :- (i) Making good of wall surface withmatching to existing surface as directed. (ii) Cost of glass and gauge shall be included in the quoted rate. 35 Supply and fix in repair aluminum alloy powder coated door made out of hollow extruded aluminum section as mentioned below. Each door having 02 Nos Disc or D type handle, 02 Nos aluminum tower bolt 200 mm size, one brass mortice lock of six lever with key in duplicate regulated by double action hydraulic floor spring heavy duty (Make:- Sandhu/Ritz) shutter to be partly glaze with 5mm thick tined coloured glass in upper pannel and partly pannelled with 12mm thick both side laminated particle board in lower pannel fixed with glazing clip, rubber beading/gasket, anodised aluminum beading screw complete all as specified and directed at site. Chowkhat Frame:- 101.60x44.45x1.60mmShutter verticle style :- 85x44.45x1.56mm Shutter middle Rail :- 83.50x44.45x1.54mmShutter Top Rail and bottom Rail :- 114.30x44.45x1.55mm 36 S & F in repairs aluminum alloy powder coated standard hollow section as mentioned below window frame (Bombay sliding) with two glazed shutter andone noswire gauged shutter sliding type, with aluminum sections as per Series-A(15mm) 3 track of Jindal section numbers for sliding windows,and glazed with tinted glass coloured glass 4mm thick, fixed with glazing clips, rubber beading / gasket anodised beading, screw and lock type handle of size 75mm, 2 Nos aluminum tower bolt 150mm long etc complete all as specified and directed. Shutter Top & bottom size : 37.50x15x1.60mmShutter inner lock size 37.50x15x1.60 mm Shutter side (Handle) size 37.50x15x1.36mm Chowkhat bottom size : 50.30x26x1.20mmChowkhat top & sides size:50.30x26x1.00mm 37 S&F Factory made 100% solid wood plastic composite ( WPC) door frame of size 75 mm x 50 mm x 50 mm made from wood plastic composite (single etruded process) material with density 780 kg/Cum from ISO certified company door should be water proof termite proof fire retardant and having good screw holding capacity all as specified and drawing complete all as specified and directed. 38 S&F 28-30mm thick moulded WPC factory made 100 % solid ( conforming as per IS-4020) made from lead free single extruded with 2,4, or 6 raised panel design on the front side with 10 mm deep mould on single with grain texure and back side plain with density not less than 600 Kg/cum, Manufacturer by an ISO: 9001-2015 certified company. The door should be water proof, termite proof, fire retardent and having screw holding capacity complete all as specified and directed. 39 S&F Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanksand similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed. 40 S&F 150 mm long, solid in one piece stainless steel 202 grade bright finishbarrel tower bolts 10mm dia shoot complete all as specified and directed. 41 S&F 150mm size solid in one piece stainless steel 202 grade bright finish handles, D type and fixed with stainless steel screws complete all as specified and directed. 42 S&F 125mm size solid in one piece stainless steel 202 grade bright finish handles, D type and fixed with stainless steel screws complete all as specified and directed. 43 S&F 100 mm size stainless steel butt hinges medium weight cold rolled fixed/ welded to frame complete all as directed. 44 S&F stainless steel sliding door bolts SS 204 grade,hasp and staple typewith bright bolt not less than 16mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 300mm long complete all as specified 45 S&FFloor door stopper of Aluminium alloy body double spring and tongue, overall length of cover plate 150 mm , anodized, with hard drawn steel spring , fixed to shutters complete all as specified and as directed. 46 M&L for preparation of new steel surfaces of any description, over 10cm in width or grith, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 47 M&L for 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed. 48 M&L for 25 mm thick PCC 1:2:4 type B-1 ( using 20 mm graded atone aggregate) complete all as specified and directed. 49 M & L for non Skid ceramic coloured tiles7-8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors e.t.cin floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed. 50 M&L glazed ceramic colour tiles size 300 mm x 450 mm x 6-7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles fixed over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. 51 M & L double charged dark shade vitified tiles 8-10 mm thick (Square/rectangular) area of each tile exc 0.11sqm but n exc 0.18 Sqm in floors e.t.c in floors etc set and jointed in neat cement slurry and pointed in coloured cement to to match the shade of tile laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed. 52 All as per item No 51 above but in dado and skirting over 10mm thick rendering in CM 1:4 to complete all as specified and directed. 53 Cutting chases, pinning in brick work making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed. 54 S&F vitreous chinaware wash down water closet pan padestal pattern white with seat cover excluding fixing bolts but including jointing to flushing cistern and flush pipe anti syphonage pipe including Jet spray etc complete all as specified and directed 55 M&Lfor looking mirror size 600x450x5mm selected qualaity mounted on 6mm commercial plywood and fixed withbrass screw and cup washer incl aluminium frame complete all as specified and directed. 56 S&F15mm bore chromium plated fancy type bib tap ofcast copper alloy with crutch of butterfly handle, screwed in iron pipe complete all as specified and directed. 57 S&Fchromium plated stop valves/ angle valve/ concealed angle valve etc, cast copper alloy, screwed down both high pressure, with crutch or butterfly handle, screwed both ends fixed, 15mm bore complete all as specified and directed. 58 S&F15mm nominal internal bore PVC connection 450mm long with two brass nuts and PVC washer complete all as specified and directed. 59 S&F 10 ltr capacity PVC low level flushing cistern including PVC syphon and float valve withPVC long band for out let connection of cistern with WC complete fixing the cistern with wall in pressured connecting with WC complete all as specified and directed. 60 S&Fvitreous china wash hand basin with pedestal white flat back, size 580x450mm excluding taps, waste pipe chain and plug and porcelain but including brackets complete all as specified and directed. 61 S&F Brass chromium plated wall mixer15mm dia complete all as specified and directed. 62 S&F CP central hole basin mixer fancy type 15mm dia all as specified and directed. 63 S&Fbrass chromium platedovehead shower with shower arm complete all as specified and directed. 64 S&F 15mm bore galvanised steelwater tubing medium grade with all fittings fixed to wall ceiling or laid in floors complete all as specified and directed. 65 S&F 20mm bore galvanised steelwater tubing medium grade with all fittings fixed to wall ceiling or laid in floors complete all as specified and directed. 66 S&F 1000 ltrs capacity Rotational moulded polyethylene water storage tanks three layers (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20 mm brass float valve with pvc ball complete all as specified and directed. 67 M & L for 75mm th PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, finished even and fair ccomplete all as specified and directed. 68 S & F 75 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring, fixed on wall complete all as specified. 69 S & F in repair 110 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring, fixed on wall complete all as specified and directed. 70 S&F 75mmPVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. 71 M & L for PCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in benching to drain, holdfast, padding to roof/chhajja, coping, bed block etc. and the like edge slightly rounded or chamfered including necessary use and waste of form work complete all as specified and directed. 72 M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. 73 S&F factory made 100 % solid wood plastic composite (WPC) flush type shutter of 18mm thickness one side laminate consisting of panel of PVC profile of 18mm (+ 0.7mm) thick of denisity 600 kg per cum manufactured by ISO-9000 certified company using for shutter cillicia ply 18mm thick and fixed with frame.The thickness of shutter is edges painted by matching colour of PVC lining ofplain/prelim coloured PVC sheet using etc complete as per manufacturer specification. 74 S & FContinuous (Piano) hinges, mild steel, bright finished or electro galvanized, width of flaps (When open) 30 mm complete all specified and directed 75 S&F magnet catcher for cub board with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed. 76 S&F Hasp and staple 100mm safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. 77 S&F 20mm dia brass chromium plated tubular towel rails fancy, D type, 60cm long between flanges, complete all as specified and directed. 78 S&F glass corner shelf of suitable size made of 5mm thick toughned glass complete all as specified and directed. 79 S&F 15mm bore chromium plated fancy typeTwo way bib tap ofcast copper alloy with crutch of butterfly handle, screwed in iron pipe complete all as specified and directed. 80 S&FCP Health Faucet with 1.20 mtr metalic Expandable tube & hook as approved complete all as specified and directed. 81 S&F Peg set of five stainless steel fixed on CP plate 40mm wide including fixing screw as per approved sample complete all as specified and directed. 82 M & L for soakage wells, of sizeof 1.8 Mtr x 3.00 Mtr effective depth as per HQ CE BZ TD Drg complete all as specified and directed. 83 M&L 65-70mm thick Pre-Cast Factory made RCC M-30 as in Cover Slab in different size of Manholes, Septic Tanks or Similar Articles with Plain Faces, all round 1mm thick plain MS sheet on the edge painted with bituminous paint on external surface incl reinforcementand RCC cover should be engraved CA No and MES and set in cement Mortar 1:4, complete all as specified and as directed. 84 S&F 150 mm Salt glazed stoneware drain pipes, grade ‘A’complete all as specified and directed 85 M&L for PCC (1:4:8) type D-2 (using 20 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and directed. 86 M & L for cuttingintoexistingmanholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as requiredcomplete all as specified and directed. 87 S&FSS grade 204 drapery rod 20mm diaincluding decorative brackets, decorative finals at both ends & curtain rings 8 Nos (Minimum) complete all as specified and directed. 88 S&F 20mm dia brass chromium plated tubular towel rails fancy, D type, 60cm long between flanges, complete all as specified and directed. 89 S&F PVC Shelves 450mm of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105 gms) 90 S&FCP Health Faucet with 1.20 mtr metalic Expandable tube & hook complete all as specified and directed. 91 S&F Peg set of five stainless steel fixed on CP plate 40mm wide including fixing screw as per approved sample complete all as specified and directed. 92 M & L for coloured prepolished rubber moulded chequred cement concrete tile 30 cm x 30 cm x 20 to 22 mm thick with spacers 3mmset, jointed and pointed in neat cement slurry as in floor with grey cement and pigment over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed. 93 M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed. 94 M&L for 60mm thick pre polished rubber moulded coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658- 2006 M-35 Grade with grey cement and no pigment complete all as specified and directed. 95 M&L for hardcore of gauge exc 63 mm but n.exc 100 mm deposited, spread and leveled in layers n.exc 15 cm thick, watered and rolled/rammed to a true surfaces in broken stone or boulder complete all as specified and as directed. 96 M&L moorum/ red bajary filling in flloors or pavings, laid in layers n. exc. 15 cm thick, spread, levelled, and rammed including watering complete. 97 M&L for point wiring with 1.5 Sqmm (nominal area) FRLSH, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in and including concealed PVC conduit medium duty 20 mm dia or higher and heavy grade conduit fittings such as socket, elbow, junction box, bell mouth, bend, reducer with suitable size of pressed iron/steel sunk box 1.2mm thick dully concealed in wall incl white frame sheet as per site for mounting of switches, sockets, fan regulator etc, one green colour FRLH cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge. Note: The wiring to be done as per IE rule and maintain colour code accordingly. 98 One light/fan/bell point controlled by one-one way switch. 99 One three pin 5 Amp socket on same board with other switches. 100 One three pin 5 Amp socket on independent board 101 M&L for point wiring with 2.5 Sqmm single core PVC insulated and unsheathed FRLSH cable, 1100 Volts, grade, multistranded copper conductor and earth continuty wire 2.5sqmm cable connected to earth dolly drawn through and including rigid PVC conduit of suitable size and conduit accessories concealed in wall by cutting grooves except on ceiling and panel in suitable way with clamps, screws etc with such as socket, elbow,junction box, bell mouth, bend, reducer including pressed iron/steel suction box 1.2mm thick for mounting of switches, sockets, fan regulator dully concealed in wall incl white frame sheet as per site for one three pin 15 Amps switch socket outlet point on independent board compete all as specified and directed. 102 All as per item No.98 above but point wiring with 4.0Sqmm single core PVC insulated and unsheathed FRLSH cable, 1100 Volts, grade, multistranded copper conductor and earth continuty wire 4.0sqmm cable connected to earth dolly for one AC point compete all as specified and directed. 103 S&F modular switch 1 way 6 Amp, 1 module, 240 volts AC all as specified and directed. 104 S&F modular switch 1 way 15 Amp, 1 module, 240 volts AC all as specified and directed. 105 S&F modular socket 3 pin 6 Amp combined, 2 module all as specified and directed. 106 S&F modular socket 15 Amp combined, 2 module all as specified and directed. 107 S&F modular bell push 1 way 6 Amp, 1 module all as specified and directed. 108 S&F bell ding dong electronic 230volt AC single pole all as specified and directed. 109 S&F modular fan regulator, 120 watt, 2 module all as specified and directed. 110 S&F ceiling rose, PVC/polycorbonate body complete all as specified and directed. 111 S & FLamp holder polycarbonate insulated body, with back plate with 09 watt LED bulb compete all as specified and directed. 112 S&F LED tube light fitting batten type 20watt 4fts polycorbonate housing, translucent diffuser with LED light source, 2200 lumen, natural white surge protection range 2KV, voltage protection reange 120-280 VAC, system efficacy not less than 110 Lm/watt for the fitting, power factor > 0.95 total harmonic distoration < 20%, colour rendering index < 80, coefficient colour temp 6500K with all accessories compete all as specified and directed. 113 S&F mirror light decorative compact luminarious with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size compete all as specified and directed. 114 S&F glaze wall light including 7/9 watt LED bulb (B-22) compete all as specified and directed. 115 S&F 35 Watt, Security light luminariescomprising of Die cast aluminium housing with weather proof gasket of lamp and driver compartment with 120 degree view angle, lumen output > 100 Lum/ watt, lumen maintenance> 70 % at 50000 hrs, color temp 5000-6500K, CRI > 70, THD < 15%, PF > 0.95 and LM 80 test compliance. The driver must be integrated APFC with short circuit protection, reverse polarity protection against 5KV high surges and comply with IEC 60598-1, IEC-61000-3-2, IEC 61547. The luminaire must have secondary optics with perfectly matched lens for better light control with and including brackets made of GI pipe of suitable dialight grade, bend to shape at an angle of 65 degree not less than 1.2mtr long with 2 Nos. of M.S clamp fabricated out of MS flat of size 50 x 6 mmon pole, including nuts, bolts, washers etc and making electrical connections with twin core twisted copper conductor flexible copper wire of suitable size from street light to junction specified and as directed. 116 M&L for sub main wiringwith 3 runs (N+P+E) of 4.0sqmm single core PVC insulated unsheathed cable 1100 Volts grade copper conductor multistrandeddrawing in and including 20 mm dia or higher medium dutyPVC concealed conduit/flexible conduit where reqd and conduit accessories and fittingscomplete incl taking out old unserviceable submain all as specified & directed. Note:-3 runs of4.0Sqmm copper cable and one run of PVC conduit shallbe measured as one unit length. 117 S&F distribution boardSPN 8 Way double door, for mounting MCBs etc factory made, IS: 13032 marked with valid CM/L Nofabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral and earthing link and 200 Amps rated bus bar complete all as specified and directed . 118 S&F MCB SP 240 volt 10 KA, 6 to 32Amp, C curve complete all as specified & directed. 119 S&F MCB SPN240 Volt 10 KA,40 Amp, C curve complete all as specified and directed. 120 S&F MCB TPN240 Volt 10 KA,63 Amp, C curve complete all as specified and directed. 121 S&F Sheet metal enclosuressingle pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB complete all as specified and directed. 122 S&FSheet metal enclosure double door DB TPN 4 way 415 Volts, 50 Hz,IP-43 protection with 200 Amp rated busbar complete all as specified and directed. 123 S&FExhaust fans made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50Hz, RPM 1200, copper winding of sweep 250 mm sweep complete all as specified and directed. 124 S&F BLDC ceiling fan complete with electronic type regulator and remote accessories 230 V, 1200 mm sweep. BEE 5 star rated PVC AC single Phase 230 V / 240V 50 Hz, connecting up ceiling rose to connector block of fan including fabricating and fixing ofFan hooks from ceiling truss/angle iron, required length of down rods (Aas per site requirement) and necessarynuts and bolts complete all as specified and directed. 125 S&FWater heater storage type,electric, capacity 25 litres AC single phase 230/ 240 V, ABS body with glass lined tank and heating element upto 2 KW, BEE 5 star rated complete with all acessories such as safety valve,thermostate, NRV and connecting up complete all as specified and directed.complete all as specified and directed. 126 Supply, laying and testing XLPE insulated galvanised steel strip or wire armoured elctric power cable with stranded aluminium conductor 1100 V gradeof size 25 sq mm 3.5 core after cutting to required length with necessary glands, nuts, bolts, and lugs laid in trenches/fixed to wall etc complete all as specified and directed 127 Excavation in trenches soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth and getting out excavated soil/sand/unseviceable LT Cable for laying of cable and getting out complete all as specified and directed 128 M&L for sand cushioning and covering of UG cable using crushed metal sand in trenches for cable protection all as specified and directed. 129 M&L for brick well burnt Class ‘B’ as cover to U/G cable laid dry flat over the cable with width equal to length of the cable and abutting each other with gap between adjacent slab not exceeding 10mm over under ground cable for cable protection in trenches complete all as specified and directed 130 Supply and laying galvanised steel tubing 40 mm bore light grade laidin trenches or fixed to poles/walls etc for cable protection complete all as specified and directed. 131 M&L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground end vertically to a depth not less than 2.25 meter deep below ground level with top edgeof the earth plate at a depth not less than 1.5 M below normal ground level connected to galvanized steel earth wire 4 mm dia by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C-1, pre-cast RCC (1:2:4) type B-1, cover slab80mm thick 32cm x 32cm reinforced with 8 mm dia.TMT bars @ 150 mm c/c both ways, and with one handle for lifting made out of 10 mm dia MS round bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing (light grade) for protection of earth lead connection, including necessary excavation and earth work in any type of soil and necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009) complete all as specified and directed.
