|
| 1 | Demolition ofUnreinforced Cement Concrete structure |
| 2 | Demolition of brickwork or stone/boulder masonery, built in cement motar. |
| 3 | M & L for R.C.C, M20, 20mm graded aggregate in Walls, retaining walls,basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses walls. |
| 4 | Material and Labour for Formwork to faces of walls,retaining walls, abutments,parapets and staircase railings and similar work including attached pillasters, buttresses,etc.; vertical or to batter. |
| 5 | Material and Labour for Providing precast slab using type B1 1:2:4 (20mm graded aggregate)in landing cover slab set in CM 1:4. |
| 6 | Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil. |
| 7 | Earth work excavation in hard/ dense soil for foundation width and depth not exceeding 1.50m and getting out. |
| 8 | Earth work excavation in hard/ dense soil for foundation width and depth exceeding 1.50m and getting out. |
| 9 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard/dense soil. |
| 10 | Material and labour for hard core using broken stoneof gauge not exceeding 63 mm deposited, spread and levelled in layers not exceeding 15 cms thick watered and rammed to through surface. |
| 11 | Laying and compacting 600 mm thick (compacted thickness)each layer not exceeding 150mm Granular Sub Base Course (GSB) grading as per Grade I as specified Table 400-1 of MoRTH specifications for Road and Bridge works, 2013, in a single layer over compacted subgrade with natural sand, crushed gravel, crushed stone, crushed slag, or combination thereof as per the grading required The materials are mechanically mixed, spread and leveling on the subgrade by using motor grader of adequate capacity, and rolling with vibratory roller of capacity 80-100 KN static weight for achieving required compaction density of atleast 98% of the Maximum Dry Density. Consolidating to required gradient and camber complete all as specified and directed with finished surface tolerances as per Table 900-1 of MoRTH specifications for Road and Bridge works, 2013. |
| 12 | Laying and compacting 300mm thick (compacted thickness) Wet Mix Macadam (WMM)WMM laid in three IayerS of 75 mm each. grading as per table 400-13 of MoRTH :specifications for Road and Bridge works 2013 manufactured in WMM plant, material comprising of clean, crushed, graded aggregate and granular material premixed with water to a dense mass, spreading with sensor paver and rolling with vibratory roller of capacity 80-100KN static weight and consolidating to required gradient and camber complete all as specified and directed The finished surface tolerances to be as per Table 900-1 of MoRTH specifications for Road and Bridge works 2013 |
| 13 | Supplying and laying 400 micron thick HDPE sheet (Virgin Quality) water proof, wrinkle free without puncture having minimum weight 390 gm/Sqm over tack coat/sand cushion as specified in the design with overlap between adjacent strips and at transverse joints as minimum 300mm. |
| 14 | Material and Labour for stone sett flooring with stone setts of size 200 to 250mm long,150 to 200mm wide and 150mm deep and sides dressed; bedded in cement mortar 1:3, joints 20mm thick; grouted in cement mortar 1:2 with an admixture of metallic floor hardner 5% by weight of cement and struck. |
| 15 | M & L for P.C.C 1:4:8, D2 type using 40mm graded aggregated in foundation. |
| 16 | M&L for cement concrete in foundation ,filling and massconcretetypeB2 1:2:4 using 20mm aggregate. |
| 17 | M & L for R.C.C A1 Type, 1: 1.5: 3 M20, 20mm graded aggregate in foundations, including rafts, footings, plinth beams etc., |
| 18 | M & L for R.C.C A1 Type, 1: 1.5: 3 M20, 20mm graded aggregate in columns, pillars, piers, posts and struts etc . |
| 19 | M & L for R.C.C A1 Type, 1: 1.5: 3 M20, 20mm graded aggregate in beams, cantilevers, bressummers, lintels over 1.50m span etc., |
| 20 | M & L for R.C.C A1 Type, 1: 1.5: 3 M20, 20mm graded aggregate in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like.etc. |
| 21 | S&F of mild steel reinforcement deformed or twisted bars10 mm dia andover, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. |
| 22 | S&F of mild steel reinforcement deformed or twisted bars 6 to 8 mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips . |
| 23 | Supply and Fixing of Hard drawn steel wire fabricweight not exceeding4 kg/Sqm cut to lengths, bent to shape required and tying with and including mild steel wire(annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt |
| 24 | Material and Labour for flat formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams,and similar work; vertical or to batter. |
| 25 | M & L for form work to side of RCC Member such as columns, pillars, square,rectangular,polygonaletc. |
| 26 | M & L for form work toflat sides and soffits of floor or roof beam, beam, lintels, cantilevers, shelves,etc. |
| 27 | Material and labour for Polycarbonite sheet 2mm thick to suit the existing roof profile as in roof covering/cladding to wall self drilling/self tapping anticorrisive serews with EPDM seal complete all as per manfacturers specification and instructions and as approved and as directed,by considering the dimension & including all necessary sceaffolding and safty aspects complete. The height of work excedding 10 meters from the average ground level. |
| 28 | Material and labourfor painting steel surfaces of any description over 10cm width or grith with two coats of synthetic enamel paint over a coat of primer including preparing new surfaces. |
| 29 | S&F of Pre-painted galvalume aluminium zinc coating GI based corrugatted steeland plain sheetboth 0.50mm (TCT) thick of an colour having tensile strength of 550Mpawith 50 mm thick PUF panelssandwitched between top and bottom galvalume sheets.50mm TCTas in roof covering/cladding to wall fixed with self drilling / self tapping anti corrisive screws with EPDM seal/screw cap complete all as per manfacturers specifications and instructions and as approved and as directed, by considering the dimensions & consideing the dimension & height including all necessary scaffolding and safety aspects complete. |
| 30 | S &F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/screw cap as specified . |
| 31 | Profiling ofPre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding or gutter,down take pipe,spouts,lintel level facesia and other aceesaries of PEB building. |
| 32 | Material and Labour for Non Metallic floor Hardner of pure carborandum basedfor concrete road surfaces the application and proportions are as per the manufacturer specifications. Make: Master Builders Solutions,MYK Arment ,Da Fixit , Fosroc ,Bostik ,/Alchemica and Tecnopol Only as approved by EIC). |
| 33 | M & L for providing Vaccum dewatering system to remove excess water from the laid/green concrete by providing suction mat on the freshly laid concrete which will not allow cement pater to flow out and the suction pump are then started immediately to remove the excess water. The suction time normally 20 to 30 minutes or as specified and as required at site and making the surface hard enough to enable carry the floating operation using mechancial trowel. The rate includes vaccum dewatering system and finshing the surface using mechanical trowel. |
| 34 | Forming 25 mm width expansion joint in concrete slab for full depth of PQC. Early entry saw and subsequent cutting by using diamond bit cutter of appropriate size, straight and smooth edges. Joint cleaned thoroughly with application of compressed air. Joint shall be made dry, vacuum cleaned and free of dirt, oil, vegetation and other debris. The joint then filled with pre-molded 25 mm thick compressible polyethylene closed cell type filler board as specified, thereafter application of two coats of primer with thin brush by forward and backward movement at an interval of 30 minutes before placing the backup rod and pouring the sealant. Placing of closed cell, medium density, crossed linked polyethylene foam backup rod of 30 mm dia, over filler board and filled with polyurethane based sealant complying with BS- 5212, BS 4254 and EN-141gzc-2003 with minimum movement accommodation factor (MAF) of+/- 30% having minimum 10 year performance guarantee, applying masked tape on the edges of joints and removing the masking tape after filling of sealant as per the method specified by the manufacturer complete as specified and directed |
| 35 | Material and labour for brick work built in CM 1:6 using sub-class \"\"B\"\" bricks ,straight or curved on plain exc 6m mean radius. |
| 36 | M&L for Plastering with CM 1:4,15mm thick onfaces ofbrick work and concrete surfaces finshed fair. |
| 37 | Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose. Area exceeding 2.00 sqm each |
| 38 | S & F of 5.5 mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane. |
| 39 | Supply and Fixing of Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples |
| 40 | Supply and Fixing of Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 41 | Designing, providing, installing and fixing factory finished custom designed cold form Light Gauge Steel Framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75mm thick steel sheet as per design requirements. The Steel sheet shall be galvanized ( AZ - 150 gms Aluminium Zinc Alloy coated steel having minimum yield strenghth 300-500 Mpa) conforming to AISI specifications and IBC 2009 for cold formed steel framing and construction and also as per IS:875-1987, ISO 800-1984 and IS:801-1975. the wind load shall be as per provisions of IS 875 (part III). LGSFS frame shall be designed as per IS:801 using commercially available software such as Frame CAD Pro-11.7/STAAD PRO-V8i/aRCHITEK V2.5.16/Revit architecture-2011 or equivalent. Proper usage of Connection Accessories like Heavy Duty Tension Ties, Light Duty Hold-ons, Twist Traps (to connect truss with wall frames), Strong Tie, Tie Rod, H-Brackets, Boxing Sections, L-Shaped Angles for better structural stability. The framing section shall be cold form C-type having minimum web depth 89mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple/slot at required locations as per approved drawings. The slots will be along center line of webs and shall be spaced minimum 250mm away from both ends of the member. The frame can be supplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. All self-drilling tapping screws for joining the members shall have a Type-II coating in accordance with ASTM B633(13) or equivalent corrosion protection of gauge 10 & 12 ,TPI 16 and 8 of length 20mm. The framed shall be fixed to RCC Slab or Tie beam over Neoprene rubber using self-expanding carbon steel anchor bolt of dia as per approved drawings and design subject to minimum 12 mm diameter and 121 mm length conforming to AISI 304 and 316 at 500mm c/c with minimum embedment of 100mm in RCC (RCC to be paid seperately) and located not more than 300mm from corners or termination of bottom tracks complete in all respects. The item also includes the submission of stability reports duly examined and issued by any NIT/IIT. The rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixing arrangement at site as described above. |
| 42 | Supply & fixing of powder coatedanodised aluminium frame for partition,doors, windows, ventilators with one or more rebates including joining cleat for fixing and power coating etc. complete all as specified(minimum thickness of powder coating 50 micron). |
| 43 | Supply and Fixing of louver ventilator made up of 0.70mmthick aluminium sheet paint coated and finished |
| 44 | Supply and fixing of Double action floor springhydraulically regulated madeup of minimum 1.25 mm thick aluminium alloy sheetfoundation box, main bodywith stainless steel cover,governing pivot made of brass,other parts made of mild steelheavy duty and fixed. |
| 45 | Material and Labour forpre-laminated particle board of 12 mm thick with both sides with decorative choice lamination. |
| 46 | Providing and Fixing false ceiling at all heights withsemi perforated 12mm thick GRG(Glass Fibre Reinforced Gypsum) flase ceiling tiles of size 595 X 595mm of approved texture design and pattern having moisture content less than 2%,humidity resistance of 99% NRCO 0.50 to 0.75 as per IS 8225:1987,noncombustible as per BS476(part-40-1970 and light reflectance of 85%(minimum) to belaid in true horizontal level suspended on interlocking metal T-grid of hot dipped GI section of 0.33mm thick(Galvanished @120 grams per sqm inculding both sides) comprising of main T runner of size15X32mmof length 3000mm,cross Tof size 15X32mm of length 600mm to form grid module of size 600X600mm suspended from ceiling using galvanished mild steel items(galvansing @80 gram perSQM)i.e 50mm long,8mm outer diameter M-6 dash fasteners,6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of 85X25X2mm galvanishediron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on perimeter wall/parttion with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws.The work shall be carried out as per specification,drawing and as per dorection of E-I-C. |
| 47 | Supply anf Fixing of Fe 410-W Gde E-250 Quality A) Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. |
| 48 | Supply and fixing Expanded metal not exceeding 4 KG/sqm, cut to length, bent to shape required and tying with and including less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members |
| 49 | Returing, refilling in the excavated trenchincluding spreading levelling, watering and well ramming in layers not exc 25 cm. |
| 50 | Removal of excavatedrocks exceeding 500m but not exceeding 1500m and depositing where directed. |
| 51 | Removal of excavated soils exceeding 500m but not exceeding 1.50Km and depositing where directed. |
| 52 | Supply and Fixing of Framed work usingFe-290(Gde E 165) as in doors orgates of angle or other sectionwith gusset plates, rails, braces, etc., complete, drilled forfixing of steel sheeting or othercovering. Doors, etc. to beprepared for hanging or slidingwith and including either hooksand hinges or steel hangingdoor fittings (exclusive of steelsheeting or other covering,running rails and guides) andhanging; also fastening andfixing complete |
| 53 | S/F of Mortice lock,vertical type, size (100 mm) with four levers, Brass body and fixed . |
| 54 | S/F of Aluminium anodised,Barrel tower bolts (150mm) of extruded section and fixed. |
| 55 | S/F of Aluminium handles (150 mm), cast type,anodised |
| 56 | M & L for light shade Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm , in floors/wall etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including Screed bedding 1:4, 25mm thick for laying floor finishes with for joint free |
| 57 | M &L for Non - skidcoloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match & joint free non skid tiles including screed bed or bedding layer in CM1:3,20mm thick for laying floor finishes. |
| 58 | Material and Labour for Glazed ceramic Coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to matchincluding screed bed in CM 1:4 15mm thick complete. |
| 59 | cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 for water tubing etc., and making good , cutting not exceeding 10cm girth in brick wall. |
| 60 | S&F of frame size 65X100mm factory made single extruded WPC(wood polymer composite) solid door/ window/ clerestory window& desertory other frames/chowkat comprising of virgin PVC polymer of k value 58-60(suspension grade), calcium carbonate and natural fiber(wood power)/rice husk/wheat husk and non toxic additives(maximum toxicity index of 12 for100mgs) fabricated with miter joints after applying PVS solvent cement screwed with full body threaded star headed SS screws having minimum frame density of 750kg/cum, screw withdrawl strength of 2200N (face)&1100N (edge) minimum compressive strength of 58N/mm2, modulus of elasticity 900N/mm2 and resistence to spread of flame ofclass A category with property of being termite/borer proof,water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteeners of required dia and length complete as per direction of engineer-in-charge.(MS hold fast/lugs or SS fasteners shall be paid for separately. |
| 61 | S&F of 30mm thick factory made single extruded WPC(wood polymer composite)solid plain flush door shutter or required sizecomprising of virginpolymer of k value 58-60(suspension grade), calcium carbonate and natural fiber(wood power)/rice husk/wheat husk and non toxic additives(maximum toxicity index of 12 for100mgs) having minimum density of 650kg/cum, screw withdrawl strength of 1800N (face)& 900N (edge) minimum compressive strength of 50N/mm2, modulusof elasticity 850N/mm2 and resistence to spread of flame ofclass A categorywith property of being termite/borer proof,water/moisture proof and fire retardantand fixing with stainless steel butt hinges of required size with necessary full bodythreaded star head counter sunk SS screws, allas per direction of engineer-in-charge. |
| 62 | S/F of Aluminium anodised,Barrel tower bolts (150mm) of extruded section and fixed. |
| 63 | S/F of Aluminium handles (150 mm), cast type,anodised |
| 64 | S/F of butt hinges (125mm) cast, brass with mild steel hinge pin,bright polished and fixed but type B-12. |
| 65 | Supplying and laying of CPVC pipes 32 mm outer diameter SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, trenches complete all as specified. |
| 66 | Supplying and laying of CPVC pipes 20 mm outer diameter SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors,trenches complete all as specified. |
| 67 | S & F of PVC 75mm dia Pipes single socketed, in any length with rubber ring joints laid in trenches or in floors. |
| 68 | S & F of PVC (SWR) 110mm dia Pipes single socketed, in any length with rubber ring joints laid in trenches or in wall. |
| 69 | Supply and Fixing of PVC (SWR) multi floor trap 75mmwith grating includingjointing with solvent cement. |
| 70 | M&L for PVC (SWR)gully trap 125/110mm setting and jointing with solvent cement. |
| 71 | S & F of PVC Bend with door 75 mm dia any radius. |
| 72 | S & F of PVC Bend with door 110mm dia any radius. |
| 73 | S & F of Gun-metal (15mm) , globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed. |
| 74 | S & F of Gun-metal (25mm) , globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed. |
| 75 | S & F of20mm Ball valves set Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight2 0 m m - 2 1 0 g m s) |
| 76 | Supply and fixing of cast copper alloy screwed down, high pressure stop cock /angle cock fancy type chromium plated concealed type of size 15mm. |
| 77 | Supply and Fixing ofVitreous China urinals, bowl typeflat back of size 465X355X265mm white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; inculding 32 mm connector pipe,stop cock15mm, PVC connections 15mm size with PTMT nuts of length 300mm and waste pipe andremoving old damaged urinal etc complete |
| 78 | Supply and Fixing of vitreous china Water closet Squatt pan of pattern \"\" long pan size 580mm white with \"P\" or \"S\" trap ,front or back inlet and foot rests ,any pattern including provision of lime concrete beddigPVC valveless 10 litres, syphonic action type , flushing cistern ,low level , white with inlet ,ball valves,float and handle including brackets Flush pipe of polyethylene of low of highdensity of PVC ,32 mm dia for low level cistern. |
| 79 | Supply and fixing of EWC Vitreous china wash down water closet pan (pedestal pattern) white with \"P\" or \"S\" trap including wash down water closet( pedestal pattern) complete high or low level flushing cistern and connections to pipes and fixing of chain and pull, or lever ,if PVC valveless syphonic action type, flushing cistern 10 liters capacity ,low level ,white with inlet ball valves ,flotand handle including bracket. |
| 80 | Supply & Fixingof PTMT health facuetwith 1.5 M long hose and apporoved colour |
| 81 | Supply & fixing of Vitreous China wash basin, white, flat back, size 580x450 wash basin. (for Hospilal use) excluding taps,waste, chain and plug and porcelain stopper but including brackets,Wash basins, Vitreous China (flat back or angle back type)any size, including cutting for andpinning in ends of brackets or erecting stand fixed in repair,32 mm Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc.with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed,15 mm Pillar taps, cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts,screwed for iron pipe and fixed. |
| 82 | S&F of Rotational moulded polye-thylene water storage tanks (cylindrical verticalwith closed top) hoistedand fixed in position all asspecified(1000 litres) |
| 83 | Supply and Fixing of 15 mm Bib taps fancy type , cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed |
| 84 | Supply and fixing of Angle Cock (15mm) with pipe (Make : Jaguar / Parryware, Cera or suitably equivalent make ). |
| 85 | Supply and fixing of PVC connections 15mm size with PTMT nuts of length 450mm. |
| 86 | Supply and Fixing ofSoap dish fixed with chromium plate brass screws and wooden/plastic cleats (make : Parryware/Jaguar/Cera)or suitably equivalent make. |
| 87 | S & F of Looking Mirror of any size as required at site selected quality glass, mount on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass. |
| 88 | Supply and fixing of tubular towel rail 20mm D type 60cm long of Barss Chromium plated with and including chromium coated brass screws and wooden /plastic cleats. |
| 89 | Supply and Fixing of Toilet paper Holder(Make Jaguar, ESS ESS, Parryware) or suitably equivalent make |
| 90 | Supply, installation, commissioning of Water cooler fully stainless steel, electric driven single phase having approx storage and nominal cooling capacity as shown150 / 150 litres |
| 91 | Supplyand Fixing of1.50 Ton inverter 5 star rating unit.Make : Blue star, Daikin, Voltas or Suitabally Equivalent Make |
| 92 | Supply and Fixing both suction and dischargecopper pipe along with insulation for spilt unit. |
| 93 | Material and labour for applying two coats of Exterior emulsionnew External wall surfacesall complete (MAKE:- ASIAN paint (Apex Ultima), NEROLAC(Excel Total) & BERGER(Weather coat long life 7 or Suitabally Equivalent Make ) |
| 94 | Materail and laying of Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), includingmaking drainage opening wherever required complete. |
| 95 | Material and labour for painting concrete surface of precast kerb stone in approved design,shape and colour of two coat of synthectic enamel paint over one coat of primer inculding preparation of new surfaces. |
| 96 | Material and labour for applying two coat of oil bound distemper on internal wall surfaces(MAKE:- ASIAN, NEROLAC, BERGER or suitabally equivalent make) |
| 97 | Material and labour for Point wiring withPVC insulated sheathed single core cable 1100V grade confirming to IS 694 multi strand copper conductor along with 2mm thick PVC conduuit accessories run on wall or roof including M.S. switch box concealed in the wall(made out of 3mm thick sheet) and laminated sun mica sheet 3mm thick cover for housing the switches, regulators and plug socket etc.mount on a wall/roof etc. including same size copper earth continuity wire.a)one light point or one fan point controlled by one switch with cables1.5 sqmm size. |
| 98 | Material and labour for Point wiring withPVC insulated sheathed single core cable 1100V grade confirming to IS 694 multi strand copper conductor along with 2mm thick PVC conduuit accessories run on wall or roof including M.S. switch box concealed in the wall(made out of 3mm thick sheet) and laminated sun mica sheet 3mm thick cover for housing the switches, regulators and plug socket etc.mount on a wall/roof etc. including same size copper earth continuity wire.b)One 3 pin socket outlet 5 amps on the same board with other switches, with cables 2.5 sqmm size. |
| 99 | Material and labour for Point wiring withPVC insulated sheathed single core cable 1100V grade confirming to IS 694 multi strand copper conductor along with 2mm thick PVC conduuit accessories run on wall or roof including M.S. switch box concealed in the wall(made out of 3mm thick sheet) and laminated sun mica sheet 3mm thick cover for housing the switches, regulators and plug socket etc.mount on a wall/roof etc. including same size copper earth continuity wire.c)One 3 pin socket outlet 5 amps on indepedent with cables 2.5 sqmm size. |
| 100 | Material & Labour forSwitch piano, flush type single pole, one way 16 Amp (Make: Anchor/ Havells/ Legrand or Suitabally Equivalent Make) |
| 101 | Material & Labour forSoket outlet piano, flush type single pole, one way 16 Amp (Make: Anchor/ Havells/ Legrand or Suitabally Equivalent Make) |
| 102 | Material & Labour forSwitch piano, flush type single pole, one way 6 Amp (Make: Anchor/ Havells/ Legrand or Suitabally Equivalent Make) |
| 103 | Supply & fixing ofsocket outlet 2 in 1,3 pin 6 A flush type (Make: Anchor/ Havells/ Legrand or Suitabally Equivalent Make) |
| 104 | Supply & Fixing of wiring for circuit/sub main wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed as required in PVC conduita) 2x2.5 sqmm + 1x2.5 sqmm earth wire |
| 105 | Supply & Fixing of wiring for circuit/sub main wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed as required in PVC conduitb) 2x4.0 sqmm + 1x4.0 sqmm earth wire |
| 106 | Supply & Fixing of wiring for circuit/sub main wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed as required in PVC conduitc) 4x10.0sqmm + 1x4.0sqmm earth wire |
| 107 | Supply & fixing Single pole andneutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps 240 VOLTS.(Make: Legrand / Havells /Anchor or suitable equivalent make) |
| 108 | Supply & fixing of sheet metal enclosures for DBs when MCBs to be used Singlepole & Neutral,12 way double door. |
| 109 | Supply and fixing amp rating 415V 10KA \"C\" curveminiature circuit breaker (MCB) of SPN 32 AMPcurrent carrying capacity in the MCBDB complete with connection testing and commissioning. |
| 110 | Supply& fixingof MCCB 3 pole 415 Volt,fixed type 125 Amps, with breaking capacity 16KA. Make: L& T / Schneider/ ABB/Havells or suitable equivalent make |
| 111 | Supply & fixing 240 Volt,10KA \"C\" curve MCB of single pole 6 to 32Amps in the MCBDB complete with connection testing and commissioning.Make Legrand/Havells/C&S or suitable equivalent make |
| 112 | Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.(Make: Havells/ Philips/ Wipro or suitable equivalent make) |
| 113 | Supply and fixing ceiling fans complete with copper winding ,blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC),IS 374-2019 Make : (Atomberg/ Havells/ Halonixor suitable equivalent make) |
| 114 | Supply and fixing ofexhaust fan, steel body AC single Phase. 230V of size 300 mm sweep with, blades, and frame and louvers (Make: Almonard/ Khaitan/ Crompton or Suitably equivalent make) |
| 115 | Supply & fixing of galvanised steel tubes, medium grade 25mm dia for ceiling fan down rod. |
| 116 | Material and labour for Brick wall cutting chases,pining in, making good to facing where required and pointing in cement mortor 1:3 to ends and cutting chases forconcealed conduit wiring, etc.,and making good,cutting exceeding 20cm girth. |
| 117 | Material & labour for .XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 3.5 core 300 sq.mm , U.G. cable with XLPE insulated aluminum conductor. (Make : Havells/Finolex/Orbit /Policab or Suitably equivalent ) |
| 118 | Material & Labour for laying of 3.5core 50 sq.mm 1100 voltage grade heavy duty, armoured, U.G. cable with XLPE insulated aluminum conductor.(Make : Havells/Finolex/Orbit /Policab or Suitabally equivalent make) |
| 119 | Supply and fixing LED street light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. (Make: Havells/ Philips/ Wipro/ Bajaj/ CG/ Luker) or Suitably equivalent make) |
| 120 | Excavating in trenches hard/dense soil not exceeding 1.5 m wide and not exceeding1.5 m in depth for laying cable. |
| 121 | Material & labour for sand filling for cushioning on U.G cable |
| 122 | Materal & labour for Bricks; common burnt clay building bricks sub class B Old sizedesignation 75 for protection to U.G cable |
| 123 | Returning, refilling in the excavated trench after laying of power cable including spreading levelling, watering and well ramming in layers not exc 25 cm. |
| 124 | Demolition of cement concreteof any description and in any position |
| 125 | Material and labour for cement concrete 1:2:4 Type B1 using 20mm graded aggregate in foundations, filling and mass concrete) |
| 126 | Supply of Galvanised steel tubes mediam grade 150 mm diameter |
| 127 | Supply & fixing of Sheet metel enclosoures for DB\"SMCCBDB 8 way DOUBLE DOOR (DPX250+24).Make:Legrand or Suitabally Equivalent Make, ( CAT No -Legrand 507759 - VTPN 8 Way MCCB DPX 3 250+24) |
| 128 | supplyof Roma 4 way uni socket 4 way, Make: Anchor/Havells/Orbit or suitable equivalent make |
| 129 | Supply of Heavy Duty Industrial Pedestal Air Circulaor Fan 600 MM(Make : Almonard / Crompton / Orient or suitabally Equivalent Make) |
| 130 | Supply and fixing of LT Pannel I/C -600 Amps-01 No, O/G -200Amps-2 Nos and 100Amps-4Nos |
| 131 | Supply and fixing of 150 WATTS LED Highbay fittings(Make: Havells/Panasonic/ Wipro/C&S or suitable equivalent make) |
