Repair And Maintenance Of Memari Division And Memari Ccc Office Under Memari(D)Division- 1 (A) Filling in foundation or plinth by fine sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) 2 Brickwork with 1st class bricks in cement mortar (1:6) in foundation and plinth. 3 125mmThickbrickworkwith1stclassbricksincementmortar(1:4)in Gr.floor 4 Plaster( towall,floor,ceilingetc.)withsansandcementmortarincludingroundingofforchamferingcornersasdirectedandrackingoutjointsincludingthroating,nosinganddripcourse,scaffolding/ staging where necessary.(i)with 1:6 cement mortar 15 mm thick plaster in ground floor 5 Neatcementpunningabout1.5 mm.in wall dado window sills drain etc. 6 Stripping off worn out plaster and raking out joints of walls,ceilings etc.upto any height and in any floor including removing rubbish within a lead of 75m as directed. 7 Dismantling all types of masonry excepting cement concrete plain or reinforced. Stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.(a) In ground floor including roof. 8 Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. In groung floor including roof.. 9 Dismantling R.C. floor,roof,beams etc.including cutting rods and removing rubbish as directed with in a lead of 75m.including stacking of steel bars.in ground floor including roof. 10 Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. 11 Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes a) Pakur Variety 12 Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes(i)pakur variety.in ground floor. 13 Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) (b) 25mm. to 30mm. shuttering without staging in foundation. 14 (c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work (i)in ground floor 15 Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. I. SAIL/ TATA/RINL 16 Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches 17 labour for chipping of concrete surface before taking up plastering work 18 Colour washing with any shade with Stainers, as required including cleaning and smoothening surface thoroughly :External surface. Two coats (on new works only). (i) Other than yellow, pink. 19 Colour washing with any shade with Stainers, as required including cleaning and smoothening surface thoroughly : (i) Internal surface (All floors) Two coats (on new works only). (i) Other than yellow, pink. 20 Applyinginteriorgradeacrylicprimerofapprovedqualityandsurfaceoldornewsurfacetoreceivedistemper/acrylicemulsionpaintincludingscrapingandpreparingthesurfacethoroughly. Waterbasedinteriorgradeacrylicprimer. 21 Applyingexteriorgradeacrylicprimerofapprovedqualityandbrandonplasteredorconcretesurfaceoldornewsurface to receive decorative textured ( matt finish ) or smooth finish acrylic exterior emulsion paint including scraping and preparation the surface thoroughly complete as per manufacturer`s specification and as per direction of the EIC. G.Fl. 22 Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturers specification) including cleaning and smoothning of surface. Two Coats 23 Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick). 24 Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to satisfy IS:4020 door testing performance criteria. In ground floor.(ii) 25 mm thick 25 Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals).(d) Sal : Local. 26 Supplying,fitting&fixingM.S.clampsfordoorandwindowframemadeofflatbifurcatedwithnecessary screws etc.by cement concrete(4:2:1)asperdirection. 40mm.x6 mm.250mm.length. 27 OxidisedironbutthingesofapprovedqualityfittedandfixedwithsteelscrewwithISImark. 100 x 58 x 1.90 mm.(Oxidised) 28 Supplying,fitting and fixing anodized aluminum barrel / tower / socketbolt 225 mm.long&10 mm.diaboltofapprovedqualitymakefromextrudedsectionwithconformingtoI.S.204/74fittedandfixedwithcadmiumplatedscrews225 mm.long&10 mm.diabolt. 29 Supplying,fittingandfixinganodizedaluminum‘D’typehandleofapprovedqualitymanufacturedfromextrudedsectionconfirmingtoI.S.specification(I.S. 230/72)complete with contibuous plate base. 100 mm.gripx10 mm. diarod. 30 Supplying,fitting and fixing anodized aluminum aldrop / sliding bolt of approved quality manufactured from extruded section confirmingtoI.S.specification(I.S. 2681/66)complete .250 mm.longby16diabolt. 31 Door stopper (Brass) 32 125 mm.longwoodenbufferblockfittedandfixedcompletewithnecessaryscrewsteak. 33 Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(ii) Other than Coloured decorative including white 34 supplying fitting and fixing urinal flush pipe fittings of approved brand.(a)C.P.urinal flush pipe fittings range of one 35 Rewashering stop cock/bib cock/push cock/pillar cock including gland (i)15mm each 36 (ii)20mm 37 supplying fitting and fixing peets valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I.marking with fittings(tested to 21 kg per sq.cm.). i)25 mm dia each 38 ii)40mm dia each 39 Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.iv) 5mm thick coloured / tinted / smoke glass. 40 Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor) (a) In Roof.With 0.60 mm thick sheet 41 M.S. works in brackets made from flats, angles, tees etc. to sizes specialy bent, twisted, forged; making holes drilled and fitted to rafter of trusses with necessary bolts, nuts, washer or screws etc. (length of straight not less than 230 mm) 42 suppling fitting and fixing UPVC pipes A-Type and fittings conforming to is:13592-1992 with all necessary clamps nails,including making holes inwalls,floor etc.cutting trenches in any soil through masonary concrete structures etc if necessary and mending good damages including joining with jointing materials(spun yarn valamoid/bitumen/m-seal etc)complete. A)UPVC pipes-110mm.dia 43 B)plain tee-110mm. Dia 44 C)plain y-110. dia 45 D)bend 87.5 degree-110mm. Dia 46 E)shoe-110mm. Dia 47 Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials (a) For Exposed Work (i) CPVC Pipes Class-1, SDR-1115 mm thk 48 supplying fitting& fixing approved patent vent cowl i.c.i conforming to i.s.s and painting two coats to the exposed surface with approved paint complete.(payment of painting will however be paid seperately).(i)100mm dia. 49 Supplying PVC water storage tank of approved quality with closed top with lid(black)multilayer. 1. 1000 liter capacity 50 supplying fitting and fixing bib cock or stop cock. Chromium plated Bib cock short body(Equivalent to code no.511&model-tropical/sumthing of essco or similar brand) 51 polythin bib cock/stop cock with plastic inlet(EMCO/ATLAS or equivalent) 15mm 52 (2) Chromium plated overhead Rain shower (Round), size-200mm dia. with revolving joint (Model Code No. F7010601 of CERA or equivalent) 53 Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. (a) With P trap 54 Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. (i) 635 mm X 395 mm X 420 mm 55 Wash basin vitreous china of approved make (without fittings) supplied,fitted and fixed in position on 75mm X 75 mm X 75 mm wood blocks and C.I. brackets including two coats of painting of C.I. brackets. (i) 450 mm X 300 mm size 56 Rectifying leakage of bed pan sink, renewing rubber washer fully complete with G.I. nuts and bolts.
