|
| 1 | Demolition of cement concrete (un-reinforced) in ground floor and paving n. exc 15 cm thick below or above ground level, complete all as specified and directed. |
| 2 | Demolition of brick work or stone boulder masonry built in cement mortar, complete all as specified and directed. |
| 3 | Dismantling of RCC shelf other than ground floors and similar suspended works, complete all as specified and directed. |
| 4 | Taking down cementplaster of any description on brick wall surfaces etc. including raking out joints hacking for key, scrubbing downwith water etc., complete all as specified and directed. |
| 5 | Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed. |
| 6 | M&L for brick work with sub class \"B\" bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg/Sqcm) old size bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6, complete all as specified and directed. |
| 7 | M&L for stone masonryrandom rubble, well bonded, bedded and solidly hearted in CM 1:6 in retaining walls abutments brought upto coarses, including necessary provn of weep holes etc., complete all as specified and directed. |
| 8 | M&L for brick work with sub class \"B\" bricks, straight or curvedon plan to any radius in half brick thick built in CM 1:4 with sub class \"B\" bricks of class designation 10(minimum compressive strength of brick 100 kg/Sqcm)complete all as specified and directed. |
| 9 | M&L for rendering 10mm thick on stone masonry surfaces or surfaces other than fair face of brick work in CM 1:6, finishing surfaces even and smooth without using extra cement, complete all as specified and directed. |
| 10 | M&L for rendering 15mm thick CM 1:4 on fair face of brick ,hollow block, concrete surface finished even and fair without using extra cement, complete all as specified and directed. Note: WPC Shall be measured and paid separately. |
| 11 | M&L for 5mm thick rendering in CM 1:3 on concrete surface of chajjas or ceiling, finished surfaces complete all as specified and directed. |
| 12 | M&L for Non Skid ceramic tiles (coloured) 300x300x 7 to 8mm thick (square/rectangular) area of each tile exc. 0.06 sqm but n. exc. 0.11 sqm as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM (1:6), complete all as specified and directed. |
| 13 | M&L for 1st quality, glazed ceramic coloured tiles 350x250x 7mm/450x350x 7mm thick on vertical surface of walls with neat cement slurry @ 3.00 Kg / Sqm incl pointed in white cement with pigment to match the shade of tiles, over and incl screed bed 10mm thick 1:4, complete all as specified and directed. |
| 14 | M&L for RCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in shelves /slabs and like with and incl use and waste of necessary form work complete all as specified and directed. |
| 15 | M&L for MS TMT Bars 10mm dia and over cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 16 | M&L for MS TMT Bars 8 mm diacut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 17 | M&L for PCC 1:2:4,type B-1, using 20mm grades crushed stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as specified and directed. |
| 18 | Taking down chawkhat or frame with (without taking of shutters from the frames) exc 1.50 sqm but n. exc 4sqm, complete all as specified and directed. |
| 19 | Taking down chowkat or frames with shutters without taking off shutters from the frames) n exc 1.5 Sqm each complete all as specified and directed. |
| 20 | S&F in repair IInd class HW Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints.complete all as specified and directed. |
| 21 | S&F 30mm flush shutters, solid core construction, with block board core and plywood face panels, commercial types on both sidesincl teak wood beading around the shutters complete all as specified and directed. |
| 22 | S&F 2nd class hard wood 30mm thick made glazed and skeleton shutters factory made open rebated and prepared to receive glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) complete all as specified and directed. |
| 23 | S&F in repair factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length and making it good to match with existing surface, complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 24 | S&F providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note: Stainless steel butt hinges and necessary S.S screws shall be measured and paid separately. |
| 25 | S&F steel windowswith side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed. |
| 26 | S&F steel windowswith side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified and directed. |
| 27 | S&F steel ventilators, with top hung shutter including hinges steel peg stay, complete all as specified and directed. |
| 28 | S&F sheet glass ordinary quality 4 mm thick glazing in square/ rectangle n.exc 0.50 sqm each pan with oil putty or aluminium beads fixed to steel and wooden of any height including necessary scaffolding and T&P required to complete the work complete all as specified and directed. |
| 29 | S&F sheet glass 4mm thick figured glass pin headed type and glazing with oil putty or wooded bead built in squares not exceeding 0.5 sq.m in each pane, complete all as specified and directed. |
| 30 | Dismantling plain or corrugated steel sheeting, with ridge, gutters, etc, any gauge, and thickness incl Nainital pattern roof covering, fixed with J/L hooks or coach screws complete all as specified and directed. |
| 31 | S&F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.60mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges ,flashing, eaves board, valley gutter etc, fixed all as per manufactures\" instructions, fixed with self tapping screws as directed by Engr-in-Charge at site with suitable arrangement as required, complete all as specified and directed. |
| 32 | S&F for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.60mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall,facia, ridges ,flashing, eaves board, valley gutter etc, fixed all as per manufacturer\"s instructions, fixed with self tapping screws as directed by Engr-in-Charge at site with suitable arrangement as required, complete all as specified and directed. |
| 33 | Dismantling of boarding of any description and in any position complete all as specified and directed. |
| 34 | S&F GI Clip-in false ceiling tiles of with beveled edges of with GI sheet (600mmx600mm) is manufactured out of 0.50mm galvanized steel of 100 gsm/sqmtr sheet having powder coated with 60 microns polyester paint on front side. These tiles shall have beveled edges. Two sides of each tiles are raised and piped and stopped to ensure positive engagement into the spring clip-in profile, yet allow for demounting of individual tiles. The rigid suspension system consists of rows of 0.5mm galvanized steel clip-in profiles of size 24mm x 34mm of 0.5mm thick and installed at 600mm c/c spacing to support the tiles, clip-in profiles are suspended with hold on clamps. Suspension angles or 4mm G.I Wire are suspended from the roof structure. The tiles are held in place by pressure clips. In the flexible system the hanger and suspension clip replace the suspension angle. G.I Edge profile are of size 24mm x 24mm x 0.35mm thick with matching the color with tiles, complete all as specified and directed. |
| 35 | S&F in repair floor door stoppers 140mm of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floors, complete all as specified and directed. |
| 36 | M&L for 75mm thick PCC 1:3:6, type C-2,using 40mm graded crushed stone aggregate, laid in 1:20 slope as in plinth protection, coping, surface finished even and incl use and waste of necessary form work complete all as specified and directed. |
| 37 | S&F Mild steel butt hinges medium weight, clod rolled, 100mm, complete all as specified and directed. |
| 38 | S&F barrel tower bolts aluminium anodised extruded section of size 200mm complete all as specified and directed. |
| 39 | S&F 300 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing cleap of sheet, cast or extruded sections, bolt not less then 12mm dia with and including a minimum of 6 bolt and nuts, fixed on plate or staple plate complete all as specified and directed. |
| 40 | S&F 250 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing cleap of sheet, cast or extruded sections, bolt not less then 12mm dia with and including a minimum of 6 bolt and nuts, fixed on plate or staple plate complete all as specified and directed. |
| 41 | S&F aluminium fabricated type extruded handles of size 150 mm complete all as specified and directed. |
| 42 | S&F aluminium fabricated type extruded handles of size 125 mm complete all as specified and directed. |
| 43 | S&F in repair 300mm mild steel ordinary rate tail rod pattern door spring incl roller and roller plate complete all as specified and directed. |
| 44 | S&F in repair 20mm dia mild steel chromium plated curtain rails fixed with brackets, stops, rollers, etc. complete all as specified and directed. |
| 45 | Taking up or down 15 mm dia steel tubing incl connectionand removal from site, complete all as specified and directed. |
| 46 | Taking up or down 20mm dia steel tubing incl connectionand removal from site, complete all as specified and directed. |
| 47 | S&F GI tubing medium gde with all fittings fixed to walls or laid in floors 15mm bore (concealed & open) complete all as specified and directed. |
| 48 | S&F GI tubing medium gde with all fittings fixed to walls or laid in floors 20mm bore (concealed & open) complete all as specified and directed. |
| 49 | S&F in repair 15mm bib tap cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 50 | S&F in repair stop valve/Angle cock/concealed fancy type cast copper alloy 15mm bore screwed down high pressure chromium plated concealed type, complete all as specified and directed. |
| 51 | S&F in repair 15mm bore CP fancy type (L-Type bend wall mixer, sink mixer & WHB mixerfor mixing hot & cold water cast copper alloy with capstan handle, screwed down for iron pipe and fixed on wall, WHB, complete all as specified and directed. |
| 52 | S&F in repair CP shower rose heavy duty with swivel joints 125mm dia fixed to 15mm GI pipe complete all as specified and directed. |
| 53 | S&F in repair vitreous china wash basin pedestal pattern super white/ colour of size 560x475mm including all fittings complete, decorative type, complete all as specified and directed. |
| 54 | S&F in repair vitreous china urinal, half stall type, of size 600x355x265mm, white (excluding flushing cistern, flush pipe), but including waste pipe fixed, complete all as specified and directed. |
| 55 | S&F in repair stop valve cast copper alloy 20mm bore screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union fixed complete all as specified and directed. |
| 56 | S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed. |
| 57 | Dismantling water tanks exc 500 n. exc 1000 ltr capacity complete all as specified and directed. |
| 58 | S&F 1000 ltr capacity rotational moulded polythenewater storage tanks (cylindrical verticalwith closed top) hoisted and fixed in position all as spd in SSR Part I, complete all as specified and directed. |
| 59 | S&F 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipes etc, complete all as specified and directed. |
| 60 | S&F vitreous china squatting span ORISSA Pattern size 580 x 440mm with integral foot rests, (excl flushing cistern and flush pipe) but with andincl connection to trap, and to flushing pipe anti-syphonage pipe, etc. complete inclprovn of lime concrete and making good to floor, in repair complete all as specified and directed, |
| 61 | S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts,) complete incl making good to floor to match with adjoining surfaces complete all as specified and directed. |
| 62 | S&F Brass with CP finished, Jet spray with flexible pipe of suitable length fixed to 15mm bore pipe (faucet) complete all as specified and directed. |
| 63 | S&F in repair plastic water closet seat cover white closed pattern with flat bottom mild steel chromium plated or aluminium hinging device fixed complete all as specified and directed. |
| 64 | S&F in repair 10 Ltrs capacity virgin polypropylene cistern, symphonic action type, ISI marked, white at low level complete with PVC bends, flush pipe and making all connections with and incl inlets ball valve float, handle, brackets and making good the disturbed surfaces in CM 1:3 to match with the existing surface, complete all as specified and directed. |
| 65 | M&L for PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate as in surface channel/ drains, incl fair finished & necessary formwork complete all as specified and directed. |
| 66 | M&L for mild steel works as in bends straps, hold fasts etc, conforming to IS-206202006 (Fe-290), embedded portion duly painted with bituminous paint and sanded, complete all as specified and directed. |
| 67 | Dismantling of 100mm cast iron or reinforced concrete drain pipe, jointed in cement mortar and taking out of trenches/ floor/ wall if required complete all as specified and directed. |
| 68 | S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified and directed. |
| 69 | S&F 110mm dia PVC (SWR) bends with oval accessed/ plain door with rubber ring joints fixed as required complete all as specified and directed. |
| 70 | S&F 110mm dia PVC (SWR) junction double, (double/ single T), equal or un equal with oval access door including jointing with solvent cement as required complete all as specified and directed. |
| 71 | S&F 110mm dia PVC (SWR) \"P\" or \"S\" trap single, equal or un equal of any length including jointing with solvent cement as required complete all as specified and directed. |
| 72 | S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified and directed. |
| 73 | S&F 75mm dia PVC (SWR) junction double, (double /single-T), equal or un equal with oval access door including jointing with solvent cement as required complete all as specified and directed. |
| 74 | S&F 75mm dia PVC (SWR) bends with oval accessed /plain door with rubber ring joints fixed as required complete all as specified and directed. |
| 75 | S&F 75mm dia PVC (SWR) floor trap, plain with SS grating including jointing with solvent cement incl necessary PCC & form work as required complete all as specified and directed. |
| 76 | M&L for preparation of new or previously untreated surface of wood or board materials of any description not otherwise described over 10cm in or girth & applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 77 | M&L for preparation of old wooden surface ofany description not otherwise described over 10 cm width or girth & applying two coats of synthetic paint complete all as specified and directed. |
| 78 | M&L for preparation of new steel surfaces including preparation of surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 79 | M&L for preparation of old painted steel surfaces including preparation of surfaces and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 80 | M&L for preparation of old decorated plastered / unplastered surfaces of ceiling one coat of white wash on ceiling andAC plain building board surfaces as in ceiling complete all as specified and directed. |
| 81 | M&L for complete removal of old plastered surfaces of walls and applying two coats of exterior emulsion/ Apex paint complete all as specified and directed. |
| 82 | Complete removal of existingold surfacesapplying two coats of oil bound distemper over one coat of wall putty (2mm) on walls complete all as specified and directed. |
| 83 | M&L for preparation ofnewly plastered or unplastered or previously untreated surfaces of walls and applying two coats of exterior emulsion paint and over a coat of primer, complete all as specified and directed. |
| 84 | M&L for two coats of distemper oil emulsion on wall incl preparation of new surfaces over one coat of primer on wall surface incl 2mm thick wall care putty, complete all as specified and directed. |
| 85 | M&L for preparation of newly decorated plastered / unplastered surfaces of ceiling one coat of white wash on ceiling andAC plain building board surfaces as in ceiling complete all as specified and directed. |
| 86 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc Laid, bedded and pointed in any mortar, complete all as specified and directed. |
| 87 | Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid & dado and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete over and including 15 mm thick screed bed or bedding with CM 1:6 ,etc complete all as spd.Note:- (i) The rate of kota stone shall be deemed to incl for full rounded off corner/ edges incl holes for pipe all cutting to make it square or rectangular.(ii) The rate shall also be deemed to incl for cutting and polishing machine and kota polishing to achieve the desired granite finish all as spfd. |
| 88 | Machine cut kota stone slab 20-25mm thick inriser steps, skirting, dado, nosing and pillar over 10mm thick cement screed base laid with CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, etc complete all as specified and directed. Note:- (i) The rate of kota stone shall be deemed to incl for full rounded off corner/ edges/nosing incl holes for pipe all cutting to make it square or rectangular.(ii) The rate shall also be deemed to incl for cutting and polishing machine and kota polishing to achieve the desiredfinish. |
| 89 | M&L for green/ black marble flooring or on cooking platform 18 to 20mm thicklaid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thickcement screed bed in CM(1:6), (size of the slabs shall not be less than 100cmx60cm )complete all as specified and directed.Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/ edges incl holes for pipe all cutting to make it square or rectangular.(ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achieve the desired granite finish. |
| 90 | Supply only water proofing compound complete all as specified and directed. |
| 91 | Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed. |
| 92 | S&Frooftrusses (framed) trussed,purlins, posts, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats Fe 410-W(Gde-E- 250), quality-A etc., complete all as specified and directed. |
| 93 | S&F framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladder, framed baluster, walk ways, railing, framework of water tanks staging and similar work conforming to Fe-290, Gde-E-165, complete all as specified and directed. |
| 94 | M&L for coloured chequred cement concrete tiles (30cmx30cmx22 to 25mm thick) in grey cement and with pigment in floors etc , set and jointedin neat cement slurry,over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed. |
| 95 | S&F in repair for 50mm thick cement concrete type D-2 1:4:8 using 40mm graded aggregate , as in filling of mass concrete for sub base floors complete all as specified and directed. |
| 96 | M&L for water proofing treatment of sunken floor of WCs, Bathroom etc. by applying of the following specifications:-(i) Cleaning of sunken floor surface with mechanical means i.e. wire brush/air blower etc. and remove all loose/ unsound material, dirt, dust, etc.(ii) Applying cement slurry mixed with acrylic based polymer modified cementitious composite compound coating Hydro proof Xtra of FOSROC/Equivalent of Dr Fixit of pidilite industries Ltd in the ration of 1:2:4(One part of acrylic polymer : Two part of water and four part of cement).(iii) First layer of cement slurry @ 0.444 Kg/Sqm mixed with acrylic based modified cementious composite compound @ 0.222 Liter/Sqm and allow it to air dry for 04 Hours.(iv) Second layer of cement slurry @ 0.222 Kg/Sqm mixed with acrylic based modified cementious composite compound @ 0.111 Liter/Sqm and allow it to air dry for 04 Hours followed with water curing for 48 hours.(v) 200 micron thick polythene film shall be pasted with help of adhesives over treatment.Note:- Joints of WC/ Trap/ Soil waste shall be properly sealed with sealing compond.Testing of all traps and joint and sunken slab shall be done as per IS-1742 before filling and tiling work. |
| 97 | M&L for PCC1:4:8, type D-2, using 40mm graded crushed stone aggregate, as in filling of mass concrete for floors, complete all as specified. |
| 98 | M&L for 40mm thick PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as base coarse for floors, complete all as specified and directed. |
| 99 | S&F in repair 600x450 mm beveled edge mirror of selected glass mounted on 6mm tick AC buildingboard or commercial plywood and fixed to wooden on plugs with chromium plated brass screws and cup washers, complete all as specified and directed. |
| 100 | S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, bracket guard and railing 60cm long incl screws, complete all as specified and directed. |
| 101 | S&F in repair soap dish chromium plated of size 180x160x90mm any type, fixedcomplete all as spd.o plugs with chromium plated brass screws complete all as specified and directed. |
| 102 | S&F in repair brass chromium plated tabular towel rail 20mm dia \"D\" type 60 cm long between flanges complete all as specified and directed. |
| 103 | S&F 0.35mm thick colour coated liner profile sheet with high quality steel fixed with self tapping screw, complete all as specified and directed. |
| 104 | Taking down carefully copper/aluminum point wiring (light, fan socket or power) complete incl. (fitting such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc.), removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc, complete all as specified and directed. |
| 105 | M&L for point wiring 1.5 Sqmm (nominal cross sectional area) with colour coding multistranded copper conductor cable, PVC insulated (FRLS-H) and unsheathed cable and including drawn through PVC conduit 20mm concealed wiring with all fittings and accessories, terminated to sunken box and laminated sheet of suitable size for housing/mounting the switches/ sockets including 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable earth wire connected to common earth dolly for one light point control by one, one way switch complete all as specified and as directed. |
| 106 | All as per Ser item No 105.00 above but for one 3 pin socket outlet 5 amps, onindependent board, complete all as specified and as directed. |
| 107 | All as per Srl item No 105.00 above but for one 3 pin socket outlet 5 amps, onsame board with other switches, complete all as specified and as directed. |
| 108 | All as per Srl item No 105.00 above but for one 3 pin 15 Amps power point on independent board with 2.5 Sqmm size FRLS-H PVC insulated unsheathed multistranded copper conductor cable and with 2.5 Sqmm FRLS-H PVC insulated unsheathed multistranded copper conductor as earth wire, complete all as specified and directed. |
| 109 | S&F switch piano flush single pole, one way 5 Amp ( ISI marked)complete all as specified and directed. |
| 110 | S&F switch piano flush single pole, one way 15 Amp ( ISI marked)complete all as specified and directed. |
| 111 | S&F socket (ISI Marked) 2 in 1, 3 pin 5/6 amps flush type complete all as specified and directed. |
| 112 | S&F socket 2 in 1, 5 pin 5 and 15 amps (ISI marked) flush type universal, complete all as specified and directed. |
| 113 | S&F ceiling rose, 3 phase ,PVC polycarbonate ,insulated body (ISI Marked) complete all as specified and directed. |
| 114 | S&F LED tube light along with fixture, 1x 20 watt, (4 Feet) wall mounted LED batten, extruded PVC, heat sink provided for efficient heat dissipation & integrated electronic driver, optics diffused, complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed. |
| 115 | M&L for lamp holder (Angle) PVC/Polycarbonate type with back plate suitable for batten fittings incl 12watt LED bulb, complete all as specified and directed. |
| 116 | S&F LED building security light 35 watt fixed on wall suitable bracket with all connected accessories complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed . |
| 117 | S&F LED tube light along with fixture, 1x 10 watt, (2 Feet) wall mounted LED batten, extruded PVC, heat sink provided for efficient heat dissipation & integrated electronic driver, optics diffused, complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed. |
| 118 | S&F LED light fitting 20W bulkhead luminaire incl LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including taking down old unsv existing fittings complete all as specified and directed. |
| 119 | S&F in replacement of bed side lamp decorative, E-27 screw type holder with 0-2 watt bulb suitable for bedroom, study room, complete all as specified and directed. |
| 120 | S&F 10Sqmm flat twin core, 1100 Volts grade, stranded, heavy duty, cable PVC insulated aluminium conductor, weather proof and including taking out the unserviceable cable, etc complete all as specified and directed. |
| 121 | M&L for submain wiring with 2x6.0Sqmm+1x6.0Sqmm Earth Wire single core PVC insulated FRLS-H, PVC sheathed cooper cableconnecting to common earth dolly in and including heavy duty PVC casing-N-cappingas per site requirement and direction by EIC, with all accessories complete all as specified and directed. Note: Three runs of copper wire for phase, neutral, earth & one run PVC conduit/ casing shall be measured one unit length. |
| 122 | S & F sheet metal enclosure MCB DB 8 waySPN double door suitable for 240 V, 200 amps rated bus bar/ DIN rail, fixed and flushed on walls including cutting Knitch and making good disturbed surfaces complete all as specified and directed. |
| 123 | S & F MCB, SP (single pole) 05 to 32 Amps, 10 kA, B curve for inductive load connected through cable lugs of suitable size complete all as specified and directed. |
| 124 | S & F MCB, SPN (single pole and neutral) 40Amps for inductive load connected through cable lugs of suitable size complete all as specified and directed. |
| 125 | S & F MCB, TPN (Triple pole and neutral) 40/63 Amps for inductive load connected through cable lugs of suitable size complete all as specified and directed. |
| 126 | S & F sheet metal enclosure MCB DB 4 wayVTPN double door suitable for 240 V, 200 amps rated bus bar/ DIN rail, fixed and flushed on walls including cutting Knitch and making good disturbed surfaces complete all as specified and directed. |
| 127 | S&F 4 Pole MCCB 63 Amp, 50 Hz, 415 V with rupturing capacity 16 KA connected through cable lugs of suitable size complete all as specified and directed. |
| 128 | S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 liter, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc and fixing arrangements complete all as specified and directed. |
| 129 | S&F MCB protected socket 15/ 20 Amp including 25 Amp MCB suitable for domestic and commercial use geyser with PVC box, sheet steel enclosure (ISI marked) flush type complete all as specified and directed. |
| 130 | Supply and laying Aluminium strip 25x3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground, complete all as specified and directed. |
| 131 | S&F Air termination, single pointed aluminium rod 12mm dia and 300mm long, complete all as specified and directed. |
| 132 | S&F test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw, complete all as specified and directed. |
| 133 | M&L for earthing complete with galvanised steel earth plate electrode 60cm×60cm×6mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less \"than 1.5 meters below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion including galvanised strip protected by 32 mm bore light grade galvanised iron pipe and earth and connected to test point as directed including funnel, watering pipe 20 mm bore light grade galvanised iron wire mesh charcoal and common salt in alternate layers of 15 cm compacted thickness all around the GI electrode with concrete pit in PCC 1:3:6 , type C-1 including necessary excavation in soft/loose soil and disposal of soil to a distance not exc 50 m and necessary testing completeconnected to earthing test point complete all as specified and directed. |
| 134 | All as per Srl item No 133.00 above but for galvanised iron strip 32x6mm as earthing lead, complete all as specified and directed. |
| 135 | M&L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire, complete all as specified and directed. |
| 136 | All as per Srl item No 135.00 above but for 32x6mm galvanised iron strip complete all as specified and directed. |
