Tender For Constr Of Labs Of Size 7M X 10.6M Under Pm Shri Scheme India At Kv No 3 At Nams (3Rd Call); 1 Excvation over areas in soft/loose soil not exceeding 1.50 metre deep and getting out complete all as specified and directed. 2 Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out insoft /loose soil complete all as specified and directed. 3 All as per ser item No 2.00 here in before but exceeding 1.5m deep and not exceeding 3m deep complete all as specified and directed 4 Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and directed. 5 Removing excavated materials not exceeding50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified. 6 Removing excavated materials exceedeing500m but n.exc 1.5km and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified. 7 M&L sand filling under floors or in foundations including watering and consolidationcomplete all as specified and directed. 8 M&L for plain cement concrete (1:4:8) type D2, using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed. 9 M&L for reinforced cement concrete, M-25 (design mix) using 20mm graded crushed stone aggregate as in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basement slabs and mass cocrete complete all as specified and directed. 10 M&L RCCM-25 (Design mix) using 20 mm graded stone aggregate as in columns, piers, Ilintel beam post etc complete all as specified and directed. 11 M&L RCC M-25 (Design mix) using 20 mm graded stone aggregate as in roof beam, cantilevers etc complete all as specified and directed. 12 M&L for RCC M-25 ( Design Mix ) using 20mm graded stone aggregate as in suspended slabs supported on walls/columns, in floors, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. 13 M&L for Form work to sides of concrete foundations, footings, base of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams etc for rough finished flat surfaces complete all as specified and directed. 14 M&L for form work to sides ofpillars, posts, struts, piers, columns and stanchions and rough finished surfaces of concrete complete all as specified and directed. 15 M&L for form work tosides and soffit of floor or roof beams, beams haunchingss, girders, brussummers, lintels, cantilevers, shelves including sup-ports, overhangs, etcand rough finished surfaces of concrete complete all as specified and directed. 16 M&L for form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and simillar works not exceeding 20cm thick and rough finished surfaces of concrete complete all as specified and directed. 17 Formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings,openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cmwide Rough finishedsurfaces of concrete complete all as specified and directed 18 M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. 19 M&L for mild steel TMTbars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bend to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 20 M&L for Brick work with old size, sub class B bricks, straight or curved on plan exc. 6m mean radius built in cement mortar (1:6) complete all as specified and directed. 21 M&L for rendering10mm thick in cement mortar (1:6) on brick work or concrete surfaces of walls, finished even and smooth without using extra cementcomplete all as specified and directed. 22 M&L for rendering cement plaster 15mm thick in cement mortar (1:4) on brick work or concrete surfaces, finished even and smooth without using extra cement mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed. ( Note :- Water proofing compound shall be measured and paid separately.) 23 M&L 5mm thick renderingin Cement Mortar 1:3 onConcrete Surfaces, ceiling etc finished surface Even and Smooth, without using extra cement complete all as specified and directed. 24 Supply only, integral water proofing compound. completeall as specified and directed. 25 M & L for preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed. 26 M&L for preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer incl a thin layer of J K wall care putty complete all as specified and directed. 27 S&F Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm per coat over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm in camouflage pattern complete all as specified and directed. 28 M&L for providing 20mmthick bedding layer of cement morter (1:3) finished even and smooth without using extra cement andmixed with water proofing compound as per manufacturers instruction all as specified and as directed.Note :- Supply only Water proofing compound shall be measured and paid separately. 29 M&L for preparation of roof surface & applying evenly a tack coat of industrial bitumen primer 85/25 grade @ 1.2 Kg/SqmincludingAPP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced wih polyster non wove fabric (wt not less than 150 gms/sqm) applied on primed surface by forced application of heat and roller, joints to be touched hot and width of overlaps not be less than 150 mm complete all as specified and directed. 30 Applying two coats of aluminum paint on top of membrane @ 0.10Kg/Sqm complete all as specified and directed. 31 M&L for powder coated aluminium window sliding type (Bombay pattern) with frame of 1.5mm thick aluminium sections including 5.00mm thick tinted glass fixed with & including anodized aluminium snap beading, glazing clips, joining clips, screws, standard rubber gasket, handles/ Knobstwo nos. for each window , MS rollers two nos. for each window shutter and including stainless steel wiremeshfixing with shutter etc complete all as specified and directed with following specifications:-(a) Aluminium section for window frame =101.50x44.45x2mm(b) Aluminium section for styles and rails of shutter = 44.0 x18.0x2mm(c) Aluminium ventilator frame with shutters shall be fixed in position in brick wall opening as required according to site conditions including all fastening arrangements etc complete all as specified and directed.(d) Aluminium window frame with shutters shall be fixed in position in brick wall opening as required according to site conditions including all fastening arrangements etc complete all as specified and directed. 32 S&FAluminiumanodised powder coatingany colour minimum coating 50 microndoor/ windows/ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed. 33 M&L for anodised aluminium powder coated door shutters, aluminium section weighting 0.55kg/m ,incl necessary ,5 mm thick, black tinted glass panes with nano coating &glazing or PVC sheet joining with cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, handles, lock , 2 x aluminium handles 150mm, 3 x hinges , 2 x Aluminium tower bolts 150mm with each shutter of any type complete all as specified and directed. 34 M&LProviding and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately 35 S & F Factory made single extruded WPC (Wood Polymer Composite) solid door frames/ Chowkhat of size 50x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant including making good after completeall as speicifed and directed. 36 S&F inDouble action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main bodywith stainless steel cover, governing pivot made of brass, other parts made of mild steelheavy duty and fixed complete all as specified and directed. 37 S&F stainelsss steel butt hinges 100mm size fixedtoframes any types complete all as specified and directed. 38 S & F aluminium handle cast type anoodised 150mm size ISI mark complete all as specified and directed. 39 S&F 150mm aluminium anodised barrel tower bolts of extruded section and fixed ISI marked complete all as specified and directed. 40 S & F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed. 41 S&F 300mm long mild steel ordinary rat tail rod pattern spring with roller plateincluding fixing with nails/ bolts or welded complete all as specified and directed. 42 S&F,20mm thick, plain white PVC sheetsingle side prelam(Celuca Ply of Rajshree make or equivalent as approved by GE) as in Shelf partition cabinet (with shelves and partitions) including necessary fittings & fixtures as per manufacturers instructions complete all as specified and directed. 43 M&L vitrified Full Body10 mm thick, in(Square/rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match, coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specfied and directed. 44 M&L for VitriefiedFull Bodytiles 10mm thick (square/rectangular) polished area of each tiles not exceeding 0.36 sqmas in vertical surfaces such as dados/skirting etc set and jointedin neat cement slury and in coloured cement to match incl plaster (backing coat) 1:4 CM 10mm thick complete all as specfied and directed. 45 M&Lhard core of broken stone or boulders of gauge not exc. 63mm deposited spread and levelled in layers not exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. 46 M&L 100mm thick plain cement concrete (1:2:4) type B1, using 20 mm graded stone aggregate as in hard standing complete all as specified and directed. 47 M&L 75 mm thick PCC 1:3:6 type C-2 using 40mm graded aggregate as in plinth protectionfinishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand (all by weight) complete all as specified and directed. 48 S & F vitreous china warecounter ovel wash hand basin, any colour, size 605x430x200mm sizefixing in slab including fixing waste pipe complete all as specified and directed. 49 S&F 450mm long PVC connections with PTMT nuts of suitable for 15mm bore dia pipe complete all as specified and directed. 50 S & F15 bore dia chromium plated Stop cock/Angle cockscrewed down high pressure with crutch or butterfly handle & screw both end for iron pipe or for unions complete all as specified and directed. 51 S&Fcentral hole basin mixer withextended spout300mm long braided connection pipe (without popup) for iron pipe or for unions and fixed to 15mm bore pipe complete all as specified and directed. 52 S & F 15 bore dia chromium plated concealed cockscrewed down high pressure with crutch or butterfly handle & screw both end for iron pipe or for unions complete all as specified and directed. 53 S&F32mm boreCP bottle trap for wash hand basin with inlet and outlet screwed for iron pipe or connections including necessary packing, union and cap complete of approved make as per sampeall as specified and directed. 54 M&L for Granite 18-20 mm thick (table rubbed and polished)in steps, jambs, pillars, window cills, cooking platforms, wash basin platform, treads, risers and like laid in cement 15 mm thick cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite rounding to edges of granite stone slabs one edge such as in counter type WHB platform etc.rubbish off the primises etc complete all as specified and directed. 55 S&F,25 mm dia, 1 mm wall thickness stainless steel fancy type, decorative curtain rod with decorative ball type side bracketscomplete all as specified and directed. 56 S&F, Grating, doom type , 100mm size of PTMT (minimum weight 25gms) complete all as specified and directed. 57 S & F 75 mm bore PVC (SWR)pipes single socketed in any length with rubber ring joints and necessary fittings laid in floors/Wall or trenches complete all as specified and directed. 58 M&L reinforcedcement concrete Type B1,1:2:4 using20mm graded aggregate as in lintel band/shelves/cover slabs (and similar articles with plain faces set in cement mortar1:4 complete all as specified and directed. 59 S&F brass, chromium plated tubular towel rack 20mm dia 60 cm long between flanges, 300mm vide with hooks complete all as specified and directed. 60 S&FTowel ring round with round flange164x53x45mm and 8mm thick complete all as specified and directed. 61 S&F ornamental stainless steeltubular pipes/sheets, pieces suchas pipe caps globe at top 18 guage and grade304 as in staircase railing including welding , moulding riveting nut and bolt with all necessary fittingcomplete all as specified and directed. 62 Supplying , fixing & Hoisting and fixingin position and connecting, in repairs, 1000 litres capacity rotational moulded polyethylene water storage tank (cylindrical, vertical with closed top) including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixedall as specified in SSR Part-I complete all as specified and directed. 63 S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed for the following bores of pipe:- 64 15MM bore of pipe 65 20MM bore of pipe 66 M&L for point wiring with 1.5 sqmm (Nominal area ) 1100 Volt PVC Insulated , FRLS unsheathed and multi strandedcopper conductor cable in New PVC Concealed conduitfor one light / fan point or bell point controlled by one switch including PVC base plates and cover plates, sheet screws and 1.6mm thick GI sunken boxes1.5 Sqmm stranded copper conductor with green PVC Insulation earth contunity conductor connected to common earth dolly etc complete all as specified and directed.Note : (i) The cost ofsunken boxes PVC base plate and cover plates included in the quoted rate.(ii)The cost of PVC concealed light boxand concealed Fan point Box is included in the quoted rate. 67 All as per Srl item No 64.00 above but for one 5 amps socket outlet independent complete all as specified. 68 All as per Srl item No 64.00 above but on the same board complete all as specified 69 All a per item No64.00 above but with 2.5 Sq mm size cable multi stranded FRLS copper wire unsheathed for one 3 pin socket outlet 15 Amps on independent board including continuous earth wire of PVC insulated 1.5 Sq mm copper solid conductor connecting to common earth dolly complete all as specified and directed. 70 Supply and FixingModular switch6 /10 Amps one way230 volts ACcomplete all as specified anddirected. 71 Supply and Fixing Modular socket, 6A 2/3 pin combined 2 module,230 volts AC complete all as specified and directed . 72 Supply and FixingModular switch16 Amps 230 volts ACcomplete all as specified anddirected. 73 Supply and FixingModular socket 6A/16A, 2/3 pin combined, two module230 volts ACcomplete all as specified and directed 74 Supply and fixing of ceiling rose 65/50 mm two to three terminals complete all as specified and directed. 75 Supply and fixing BLDC(Brushless direct current motor) ceiling fan 1200mmsweep alongwith remote control unit,copper windinglowpower consumption,high speed Aluminium body with blade, double ball bearing having minimum air delivery 220 CMM and BEE 5 star rated Including acessories connector, canopy, HangingRod and clamps , including electric connection with pvc flexible twin core copper wire from ceiling rose to ceiling fan complete all as specified and directed. 76 Supply and fixingin replacement modular fan regulator, 120 W, two module,electronic step type heavy duty socket type 230 volts complete all as specified and directed. 77 Supply and fixing concealed Lightround shape 18 watt 220 volts AC Surface Mounted Downlighttype with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roofconceal ceiling light including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 78 Supply and fixing of MCB 40 Amps single pole with neutral, AC 230 Volts complete all As specified and directed. 79 Supply and fixing of MCBs single pole (SP) 5 to 32 Amps with 10 KA breaking capacity of B series in distribution boards complete all as specifiedand directed. 80 Supply and fixing Single pole and neutral enclosure 32 A, 230 V with a two pin and earthplug and socket complete with one Singlepole MCB 25 A complete all as specified and directed. 81 Supply and fixing sheet metal enclosure for DB’s (Double door type) when MCB’s to be used, single pole and neutral, 12 ways with 200 ampere rated bus bar, 240 volts fixed sunk / flush to the wallwith IP-43 and IK-09 protectioncomplete all as specified and directed. 82 Supply and fix in replacementfor sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area6.0 Sqmm drawing into and including PVC non metallic rigid conduit medium grade of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 6.0 Sqmm as a earth continuity conductor(green colour) and including non metallic medium graderigid PVC conduit, including cutting chases in brick wall,and making good to match the existing specifications complete all as specified and directed. Note :- (i)Rates are deemed to be included cutting and making holes in wall/floor for passing in or through conduit (ii)Two run of6.00 sqmm single core (FRLS) PVC insulated copper conductor cable, one run of 6.0 sqmm copper conductor cable (FRLS)as a earth lead and one run of PVC conduit of suitable size will be measured as a one unit. 83 all as per item No 80.00 above but for 4.0 sqmm complete all as specified and directed 84 Supply and fixing of LED T-8 tube light fitting with single side connection LED tube rod 18/20 W, 4 Feet made of CRCA sheet steel box type including bipin holder and connection with PVC insulated twin core 23/0.0076 ywisted copper cable from ceiling rode to light fitting complete all as specified and directed. 85 Supply, laying in trenches or wall and testing in replacement of cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sqmm 4 core all as specified and as directed. 86 M&L for earthing completewith galvanisedsteelearth plateelectrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade)and watering pipe 20 mm bore GI pipe(light grade ) andchamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg.50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PART 1 , with charcoal dust and saltcomplete and earth leadconnected to earthing test point (up to main switche, DBs) completeall as specified &testing on completion. 87 Supply,laying & fixing double wall corrugated (DWC) pipes made of high density polythyline (HDPE) with all accessories i.e. all type of joints, Sockets, Elbows, bends and End caps,ofsize 63mm outer dia and 50 mm inner dia etc. complete allas specified and directed 88 Supply and fixingDistribution board of sheet steel enclouser distribution boards, double door factory madeTPN Vertical4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulatedcopper jumpers of suitable size from the MCCB to the out going circuits oneincoming MCCB and 12 outgoing MCBs circuits comprising of 3 phase 4 wireof suitable rating complete all as specified and directed with the following accessories :-(a) MCCB 100 amps, 25 KA, FP, 415 volts, 50 Hz and out going MCB.(Note:- Out going MCB shall be measured and paid for separately) 89 Supply and fix of security light fitting LED 25 Watt withaluminum pressure dia cast housing with touched glass cover IP-66 protectionIncludingsuitable sizeand accessories complete mounted including connection with 3 core PVC insulated overall sheathed flexible cable with muyltistranded copper conductor of size not less than 1.0 sq mm from celing rose to fitting terminal all as specified and directed. 90 S& F GI bracket light grade GI Pipe 1.2 mtr Length for fixing of street light fitting25/36 Wattincluding connection complete all as specified and directed. 91 Boring of hole under road for passing of electriccable through DWC pipe complete all as specified and directed. 92 M & L cutting of exsiting Steel tube any size for alternation / addition of pipes complete all as specified and directed. 93 Supply and fixing 25 mm bore pipe mild steel tube medium grade galvanised with all fittings laid in trenches complete all as specified and directed. 94 Supply and fixing 25 MM bore gun metal gate valve screwed down high pressure with crutch with or butter fly handle screwed both ends for pipe complete all as specified and directed. 95 S&F 110mm bore PVC (SWR) pipes rain watee/ drain pipe single socketed in any length joints laide in trenches including benching haunching in PCC 1:3:6 complete all as specified and directed
