Tender For Special Repair/Annual Repair Work Of Rest Houses Under Sub Division No.1 Rewa - Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deepand disposal of rubbish, lead upto50 m and liftupto1.5 m.All kinds of soil. 2 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. 3 Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared. 4 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in over areas foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. 5 Filling available excavated earth (excluding hard rock/Ordinary rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 6 Supplying and filling in plinth with stone crusher sand under floors including, watering, ramming consolidating and dressing complete. 7 Supplying and filling in plinth under floors including watering ramming consolidating in layers not exceeding 20cm in depth and dressing complete. 22.27.1 With hard muram having CBR >12 % at under floors including watering, ramming and compacting (minimum compaction 95% of MDD) in layers not exceeding 20cm in thickness and dressing complete. (Note:- maximum thickness of this layer to be provided shall be 30cm) 8 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 sand) to match the existing floor :With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration. 2.30.3 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 sand) to match the existing floor : With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration. With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration. 9 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level : 4.1.1 With 20mm nominal size graded stone aggregate. 4.1.1.2 M 20 – Grade concrete. 10 4.1.1.3 M 15 – Grade concrete. 11 Demolishing lime concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of Engineer-in-charge roof. 12 Dismantling stone slab roofing over wooden karries or R.C.C. battens (dismantling karries and battens to be paid for separately) includingstacking of serviceable material and disposalof unserviceable material within 50 metres lead. 13 Dismantling wooden ballies in posts and struts including stacking within 50 metres lead 14 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. 15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix). 15 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 16 Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge: 15.8.1In lime mortar 17 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 15.6.3 In cement mortar 18 Boring, Providing and installing cast in situ single under reamed piles of specifieddiameter and length below pile cap in M 20 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, cement concrete and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured uptoto the bottom of pile cap) : 20.10.1 250 mm diameter pile. 19 Providing and laying in position specified grade of reinforced cement concrete (with 20mm nominal size graded stone aggregate) excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 5.1.1 M 20 –Grade Concrete 20 Reinforced cement concretework (with 20mm nominal size graded stone aggregate) in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, posts and struts etc. above plinth level and up to floor two level excluding cost of centering, shuttering, finishing and reinforcement.5.2.1M 20 –Grade Concrete 21 Reinforced cement concrete work (with 20mm nominal size graded stone aggregate) in beams, suspended floors, roofs having slope of any degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level and up to floor two level excluding the cost of centering, shuttering, finishing and reinforcement in concrete grade. 5.3.1 M 20 –Grade Concrete 22 Centering and shuttering including strutting, propping etc. and removal of form for :5.9.1Foundations, footings, bases of columns, etc. forconcrete up to plinth level. 23 Columns, Pillars, Piers, Abutments, Posts and Struts. 24 Lintels, beams, girders, bressumers and cantilevers. 25 Suspended floors, roofs, landings, balconies and access platform. 26 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding including cost of binding wire up to floor two level including all wastage etc. complete. 5.16.6Thermo-Mechanically Treated bars.(TMT) 27 Brick work withwellburntchimney bricks inbulls patenttrench kiln, crushing strength not less than 25kg /cm2 and water bsorption not more than 20% in superstructure above plith level and up to floor two level i/c curingetc complete. 6.4.2Cement Mortar 1:6 (1 cement : 6sand). 28 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer all complete 29 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :4.1.2With 40mm nominal size graded stone aggregate.4.1.2.2Nominal Mix -1 Cement : 3 sand : 6 graded stone aggregate (M 10) 30 4.1.1With 20 mm nominal size graded stone aggregate. 4.1.1.4Nominal Mix -1 Cement : 3 sand : 6 graded stone aggregate (M 10) 31 12 mm cement plaster finished with a floating coat of neat cement of mix : 13.4.2 1:4 (1 cement : 4 sand) 32 Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. 33 6 mm cement plaster of mix : 34 12 mm cement plaster of mix :13.1.21:6 (1 cement : 6 sand) 35 15 mm cement plaster on the rough side of single or half brick wall of mix : 13.2.21 : 6 (1 Cement : 6 Sand) 36 Providing and laying vitrified floor tiles (without soluble salt) or printed (with soluble salt) Nano polished (Glossy finish) in different sizes with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, 1st quality/ premium quality in flooring laid on 20mm thick cement mortar 1:4 (1cement : 4sand) including grouting the joints with white cement and matching pigments etc. complete. 11.76.2 Dark shade (terracotta) Size 600X600mm thickness 9-10mm 37 Providing and laying rectified Glazed Ceramic floor tiles 300x300 mm or more (having thickness 9 to 10mm) of 1st quality conforming to IS : 15622 of approved make in all colours white, ivory, grey, fume red brown laid on 20mm thick cement mortar 1:4 (1 Cement : 4 sand) including grouting the joints with white cement and matching pigments etc., complete. 38 Providing and laying rectified Glazed Ceramic wall tiles 300x450 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in all colours white, ivory, grey, fume red brown laid on 12 mm thick cement mortar 1:3 (1 Cement : 3 sand) including grouting the joints with white cement and matching pigments etc., complete. 39 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, Like birla white /JK white or equivalent, over the plastered wall surface to prepare the surface even and smooth i/c all cost of material, labour and scaffold etc in all position complete. 40 Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : 14.53.1 One or more coats applied on walls @ 0.85 ltr/10 sqm. 41 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : 17.2.1W.C. pan with ISI marked white solid plastic seat and lid 42 Providing and fixing white vitreous china flat back Anti germ fluoro-polymer coated urinal (Inbuilt spreaders, bottle trap and ceramic waste coupling) with 15mm brass pressmatic auto closing concealed urinal flush valve with wall flange (decol technology, 400000 operation warranted) i/c cutting and making good the wall and floors wherever required, all fittings and fixtures etc. complete. 25.11.1 White Vitreous China Anti germ Fluoro-Polymer Coated Urinal Size 340x325x650 mm. (Premium Range) 43 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern,includingpainting of fittings and brackets, cutting and making good the walls wherever require :17.11.2White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap. 44 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shape with 6 mm thick hard board backing. 17.68.4Rectangular shape 1500x450 mm 45 Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. 46 Providing and fixing CP brass towel ring of approved quality and make.200mm dia ring 47 Providing and fixingC.P. brass soap container 109 mm wide, 125 high and 112 mm distance from wall of standard shape with bracket of the same material with all fittings etc. of approved quality and make like jaquar or equivalent conforming to IS:specification. 48 Providing and fixingC.P. brass grating of approved quality and make conforming to IS:specification. 17.78.1 100 mm dia. 49 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 18.8.115 mm nominal outer dia .Pipes. 50 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plainand brass threaded fittingsi/c fixing the pipe withclamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. 18.6.1 Internal work - Exposed on wall. 18.6.1.1 15 mm nominal outer dia .Pipes. 51 18.6.1.3 25 mm nominal outer dia. Pipes. 52 Providing and fixing brass bib cock of approved quality. 18.29.1 15 mm nominal bore 53 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15 mm nominal bore 54 Providing and fixing in position best indian Health Faucet with 8mm dai 1 meter long Flaxible Tube and wall bracket with N. R. V. (non-return wall). 55 Constructing soak pit 1.20x1.20x1.20m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20m long complete as per standard design. 56 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 sand) including 500x450 mm precast R.C.C. horizontal grating with frame complete as per standard design :19.27.1Withwell burnt bricks 57 Providing and laying below ground unplasticised PVC pipe to with stand working pressure of 4 kg/cm2 soild waste pipes confirming to IS:13592 and IS:4985 including jointing with seal ring confirming to IS :5282 leaving 10mm gap for thermal expansion all necessary fittings etc. complete. Excavation to be paid seperataly. 19.4.1110 mm diameter OD 58 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 19.23.1For pipes 100 to 230 mm diameter 59 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 18.12.125 mm nominal bore 60 Providing and fixing unplasticised Rigid PVC soil and waste pipes conforming to IS: 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Single socketed pipes for working pressure of 4 kg/sqcm. 17.58.1 75 mm diameter (minimum wall thickness 3.2mm) 61 17.58.2 110 mm diameter (minimum wall thickness 3.2mm) 62 Providing and fixing unplasticisedPVC moulded fittings/ accessories for unplasticised Rigid PVC soil and waste pipes conforming toIS: 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. 17.59.5Bend 87.50. 17.59.5.175 mm bend 63 Single tee without door. 17.59.4.1 75x75x75 mm 64 Single pushfit Coupler. 17.59.2.175 mm 65 17.73 Providing and fixingCP brass towel rail of approved quality and make. 17.73.1600x20mm 66 Providing andfixingwhitevitreouschinapedestalfor wash basin completely recessed at the back for the reception of pipes and fittings. 67 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice .husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-InCharge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)9.170.1 24 mm thick WPC (Wood polymer composite) solid plain flush door shutter 68 Providing and Fixing, factory made, PVC door frame made of PVC. Extruded sections of size 75mmx53 mm, having wall thickness 2.0mm (±0.2mm). Both verticals sides of the frame reinforced with PVC profile of cross section size 28mm x 30mm x2mm thickness (± 0.2 mm) and 75mmx200 mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut jointed and fusion welded together, including providing and fixing 3 nos. of 125mm long stainless steel hinges to frame, fixing the frame with jamb with required nos. and sizes of anchor dash fastener, all complete as per manufacturers specification and direction of engineer-in-charge. 69 Providing and fixing ISI marked stainless steelhandleswith necessary screws etc. complete : 9.69.2100mm 70 Providing and fixing ISI marked stainless steel door latcheswith screws etc. complete : 9.68.2250x20x6 mm 71 Providing and fixing glass panes/ steel sheet/ Fibre sheet with putty and glazing clips in steel doors, windows, clerestory windows all complete. 10.27.2 With 5.5 mm thick glass panes. 72 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 73 Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50metres lead : 74 Steel work in built up M.S. tubular section (round, square or rectangular hollow tubes etc.) trusses/frame work etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.14.1 Hot finished welded type tubes 75 Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or Lhooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 12.1.30.63 mm thick with zinc coating not less than 275gm/m² 76 Removing dry or oil bound distemper,water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 77 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : 14.36.1One or more coats on old work 78 Renewing glass panes and refixing existing wooden fillets: 14.7.1Float glass panes of thickness 4 mm 79 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 14.37.1 One or more coats on old work. 80 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm all complete. 9.46.1With 2nd class teak wood beading 62x19 mm.
