Tender For Stage Contract For Division Pahalgam- 1 Earthwork in excavation by mechanical means in foundation trenches, drains, pipes and asbles etc (not exceeding 1.5 Mir In of 10 Sahin plant including dressing of sides and ramming of bottoms, lit upt 15 Mr Including griting out anated tod and disposal of surplus soil as directed and lead up to 50 Mtrs. 2 Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared. 3 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 4 Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil. 5 Providing and laying hand packed stone soling in foundation under floors etc incl ramming, watering and consolidating complete.cort al carriages of all materials involved upto site of work complete job. 6 Providing and laying in position cement concrete of specified grade M-7 5 excluding the cost of centering and shuttering-All work at all levels in 1:48 (1 Cement 4 coarse sand 8 graded stone aggregate 40 mm nominal size) including cost and carriage of all materiali involved upto site of work complete job. 7 Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design imis, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of RMC from transit mixer to site of laying excluding the cost of centering, shuttering finishing and forcement including cost of admixtures in recommended proportions as per 15 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability na per direction of the Engineer in charge Note Cement content considered in this item is @ 330 kg/ cum. Excess less cement used as per design mis is payable recoverable separately All works upto plinth level, complete job. 8 Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement control as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS 9103 to accelerate/retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer in charge Note Cement content considered in this item is 330 kg/ cum. Excess/ less cement used as per design mix is payable recoverable separately All works above Plinth Level & Upto Floor V Lvl, complete job. 9 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering 1.2.4 (1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size), incl. carriages, complete. 10 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level, Thermo-Mechanically Treated bars of grade Fe-500D or more. 11 Brick masonry with FPS bricks of class designation 75 in super structure upto floor V level in cement mortar 1:6 (1 Coment: 6 course sand) comp-ete as per the directions of EIC including cost & carrings of all materials involved to site of work, complete job. 12 Brick masonry with FPS bricks of class designation 75 in foundation and plinth in cement mortar 1:6 (1 Coment: 6 course sand) comp-ete as per the directions of EIC including cost & carrings of all materials involved to site of work, complete job. 13 Providing and fixing Ist quality ceramic glazed Wall Tiles high gloss conforming to IS:13753 of miniumum thickness to min of approved make like NITCO, ORIENT, SOMANY KAJARIA or equivalent make in all colours, shades exceps begundy, bottle green, black of any size as approved by the Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick hed of Cement Mortar 1:3 (1 Cement 3 Coarse sand) and jointing with grey cement slurry @3.3kg per sqm including pomtang in white cement mixed with pigment of matching shade complete sample to be approved by Engineer-in- Charge Sizeof Tile 450 x 300 mm (including cost of all material, leads, lifts and carriages etc upto site of work complete) 14 Providing and fixing lat quality ceramic glazed Floor Tiles conforming to 15:13753 of miniumum thickness 6 mm of approved make like NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in all colours, shades except begundy, bottle green, black of any size as approved by the Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of Cement Mortar 1:3 (1 Cement: 3 Coarse sand) and jointing with grey cement slurry @3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete sample to be approved by Engineer-in-charge. Size of Tile 300 * 40 num (including cost of all material, leads, lifts and carriages etc upto site of work complete). 15 Steel work in built up trusses etc, including cutting, hoisting, fixing in position and applying a priming coat of approved steel pruner, including welding andbolted with special shaped washers etc. complete 16 Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 17 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 18 Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 19 Providing and fixing plained eaves boarding of (250*32mm) N/S with necessary grooves and chamfer as per detailed drawing) (Second Class Kail Wood) incl cost of nails 20 PF of 12mm thick T&G planks made of imported wood (New zealand pine or equivalent) for roof soffits & Ceiling on wood work in false ceiling, partitions sawn and putup in position in budloo wood (Ceiling Joists), including cost of necessary adhesive 35&cost of nails etc with necessary comice of required size complete job. incl cost of nails / screws all complete as approved by Engineer-in-charge (including cost of all material, leads, lifts and carriages ete upto site of work complete). Soffits 21 P/L pinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm (Nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand includingfinishing the top smooth. 22 Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing and fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 liter/6 liter (adjustable to 4 liter/8 liters), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. 23 Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer 24 Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 25 Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 26 15mm dia braided connection pipe. (of approved brand) 27 Providing and fixing of liquid soap dispenser with brackets fixed to wooden cleats with CP brass screws of approved brand. 28 Providing and fixing of CP brass Health faucet with 8mm dia 1 mir. Long PVC tube and wall hook fixed to wall with rawi plugs and CP brass screws complete of approved brand. 29 Providing in position storage type Hot Water electrical horizontal heaters with copper container, insulation, and stove enameled MS jacket, thermostatically controlled immersion heater, with pilot lamp, 15/20mm dia inlet with non return valve and 15/20mm dia outlet including making connections complete in all respects. (wall mounted with suitable M.S bolts and nuts) Capacity 50 Litte of approved brand. 30 Providing and fixing uPVC SWR Pipes class B (IS:13592) with all injection moulded fittings complete including jointing with solvent cement including cutting and making good the walls wherever required (For soil, waste, vent & rain water pipes) Nothing extra will be paid for supports. Make: Pipe & fittings:of approved brand110 mm outer dia 31 150 mm outer Dia. 32 Providing and fixing 3 layer PP-R(Poly propylene Random copolymer) pipes SDR 7.4 UV stabilized & anti-microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain and brass threaded 150mm outer dia polypropylene random fittings i/c fixing the pipe with clamps at 100m spacing. This includes the cost of cutting clases and making good the same including testing of joints complete as per direction of Engineer-in- charge of approved brand.internal work concealedPN-16 Pipe 20mm OD 33 PN-16 Pipe 25mm OD 34 PN-16 Pipe 32mm OD 35 Carpenter for set right of existing doors, windows, wire gauge shutter i/c cost of Screws, Complete Job. 36 P/f of imported wooden 12mm thick (T&G) panelling fixed on 12mm ply board l/c f frame work of budloo wood incl. all carriages compelete-job Incl. Polishiong with two or more coats. 37 Providing and fixing of KHATAM BANDI ceiling of first class budloo/fir wood including the cost of frame work and applying coats of polish.Chaar Gul. All complete 38 P/F Of file racks l/c 19mm plywood and dunmica 1-6 Deep with fixtures all complete. 39 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. For thickness of tiles 10 mm to 25 mm 40 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. Size of tile 600*600 mm. 41 Providing & laying 16 mm minimum thick pre-polished (best quality) Granite stone slabs (non water absorbing) in counters, vanities etc on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand)/12mm thick backing of cement mortar 1:3 (1 cement: 3 coarse sand) and joined with white cement slurry mixed with pigment or with standard tile made compound to match the shade of the slab. Including rounding, rubbing, clamping, curing, moulding, granite polish & making grooves as required complete (Note: The stone slab shall be cut to required size and laid to the required pattern including rounding, chamfering, bull nosing of the edges as directed. Actual area of slab, as laid shall be measured) Sample to be approved by Engineer-In-charge. (including cost of all material, leads, lifts and carriages etc upto site of work, complete job. 42 P/F of 3.5mm hick glass panes with all fittings complete job. 43 P/f wall paper i/c carriage all complete job. 44 Providing and fixing PTMT brass bib cocks OF APPROVED QUALITY AND COLOUR. 15 mm bore, 122mm long, complete job. 45 P/F LOW level flushing cistern with manually controlled device. With all fittings and fixture complete. 46 P/F of PVC connection all complete. 47 Engagement of JCB for clearence of site, earthwork in excavation, removal of malba etc 48 Engagement of labour for one day 49 Engagement of skilled labour for one day 50 Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed:: All kinds of soil 51 Providing and laying in position cement concrete of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including curing & carriage of material but excluding the cost of centring and shuttering. All work upto plinth level 52 Providing and laying in position reinforced cement concrete of 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) including curing & carriage of material but excluding the cost of centring and shuttering, complete 53 Providing and laying in position cement concrete of 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) including curing & carriage of material but excluding the cost of centring and shuttering, complete. 54 Centering & shuttering including strutting, propping etcincluding removal of form work for :Foundations, footings, bases for columns, plinth etc 55 Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. 56 Lintel, beams, plinth beams, girders, bressumers and cantilevers. 57 Suspended floors, roofs, landings, balconies and access platforms. 58 Providing wood work in frames of doors windows, clerestory windows and other frames wrought framed and fixed in position with hold fasts lugs or with dash fasteners of required dia and length (hold fasts lugs or dash fasteners shall be paid for separately (imported Kail wood) including all carriages complete. 59 Providing and fixing 35panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (imported wood ) 60 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws , including panelling with Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side, Grade I, Type II . ( For Doors) 61 P/F and fixing 35mm thick wire gauze shutters using galvanized MS wire guaze of average width for aperture 1.4mm with wire of Dia 0.63mm for doors, windows and clerestory windowsincluding ISI marked bright finished or / and black enameledMS but hinges with necessary screws including all carriages complete (imported wood) 62 Providing and fixing of 4 mm thick glass panes (Weight not less than 10 kgs/Sam) including cost of wooden beadings 63 Providing and fixing of 0.5mm thick colour coated iron profile sheet roofing accessories in ridges, valleys etc (500 to600 MM wide) of approved profile and colouras approved by Engineer-in-Charge with self drilling /self tapping screws of size(5.5 x 55mm) with EPDM seal of same colour matching the shadeof ridges/valleysincluding carriage of same upto site of work complete. 64 12mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 4 ( 1 cement : 4 fine sand) including Carriage complete 65 12mm Cement plaster on the rough side of single or half brick wall of mix: 1 :6 ( 1 cement : 6 fine sand) including Carriage complete 66 15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 4 ( 1 cement : 4 fine sand) including Carriage complete 67 15mm Cement plaster on the rough side of single or half brick wall of mix: 1 :6 ( 1 cement : 6 fine sand) including Carriage complete 68 Providing/applying White cement based putty of average thickness 2mm of approved brand and manufacture over plastered wall surface to prepare the surface even and smooth including all carriages complete. 69 Providing and fixing of Hardware Fixtures toShutters of Doors & Windows:Brass Finished bright of std make :Tower Bolts 100mm length 70 Handles 100 mm 71 150 mm 72 L Drop(250mmx16mm) 73 Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete,complete. 25mm thick with 12.5 mm nominal size stone aggregate 74 40mm thick with 20 mm nominal size stone aggregate. 75 50 mm thick with 20mm nominal size stone aggregate. 76 Providing and laying of 50mm thick Coloured interlocked rubber moulded cement concrete tiles of required colour and manufactured in M20 Grade ( sample to be got approved by incharge engineer at site) laidover and including a Bed of 50 mm thick sand cusion with all carriages up to site of work 77 Providing and fixing of 18 mm thick plywood of approved brand and quality with all necessary fitting andfixtures and scafflolding all complete as per directions 78 Providing and fixing of 12 mm thick plywood of approved brand and quality with all necessary fitting andfixtures and scafflolding all complete as per directions 79 Providing and fixing of 6 mm thick plywood of approved brand and quality with all necessary fitting andfixtures and scafflolding all complete as per directions 80 Providing and fixing wooden moulded corner beading of size 50x50 mm (base and height) of triangular shape to the junction of paneling etc. with iron screws, plugs and priming coat on unexposed surface etc. Complete second class kail wood 81 Applying priming coat:With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) 82 With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel works 83 Painting with synthetic enamel paint two or more coats of approved brand and manfacturer on wood work 84 Painting with synthetic enamel paint two or more coats of approved brand and manfacturer on wood workon old work 85 Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm) 86 Painting with aluminum paint of approved brand and manufacture to give an even shade. Two or more coats on new work 87 French spirit polishing, Two or more coats on new works including a coat of wood filler 88 Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats 89 Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade 90 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 91 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, one or more coats on old work. 92 Painting with aluminum paint of approved brand and manufacture to give an even shade, one or more coats on old work. 93 French spirit polishing, one or more coats on old work 94 Providing/Fixing CP Brass fittings of standard quality and make (Jaguar/ equivelant standard make)Wall Mixer 95 Basin Mixer 96 Towel rod 97 Towel ring 98 Ball Value, 15 mm of C.P Brass 99 Ball Value, 20 mm of C.P Brass 100 Ball Cock 101 Tanky nipple 102 soap case 103 Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 104 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 18.2.1 W.C. pan with ISI marked white solid plastic seat and lid 105 Providing/Fixing of PVC pipes and fittings ofprince make or equivelant including jointing / testingcomplete(B Type )Pipe 100mm dia 106 Pipe 75mm dia 107 Door Tee 100mm 108 Door Tee 75mm 109 Plain Tee 100mm 110 Plain Tee 75mm 111 Reducer 75 x100mm 112 Providing/Fixing of GI pipes and fittings ofapproved brand including jointing / testingcomplete(Medium Type )15mm dia 113 Pipe 20 mm 114 Pipe 25 mm 115 Union 15mm 116 Union 20 mm 117 Union 25mm 118 P/F of looking mirror of superior glass of approved make and required shape and size with plastic moulded frame with 6mm thick hard board backing size( 1.25x2.0 ) 119 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 127101 marked indicating the BIS licence no. with cover and suitable locking arrangements and making necessary holes for inlet, outlet and overflow pipes All complete 120 Construction of Brick masonry Man hole in cement mortat 1:4 with MS frame and cover including palasteringthe internal surface with 12 mm thich palster in 1:4( Size 1.5 x 1.5x1.5 ) all complete as per the directions of incharge engineer at site 121 P/l of wall-to- wall of superior quality including 10 mm thick thermocoal ( sample to be got approved from incharge engineer at site ) with all carriages, complete as per directions of EIC 122 Construction of wardrobe1.5 deep wardrobes cabin with 19 mm thick plywood and 10 mm thick plywood on back side ,plywood shutters fixed with denmica of std make on expopsed surfaceswith all fittings and fixtureslike handles, locks , catchers etc including carriage of materialall complete as per the directions of incharge engineer at site (Face area to be measured) 123 Construction of wardrobe2 deep ward robeswith 19 mm thick plywood and 10 mm thick plywood on back side ,plywood shutters fixed with denmica of std make on expopsed surfaceswith all fittings and fixtureslike handles, locks , catchers etc including carriage of materialall complete as per the directions of incharge engineer at site (Face area to be measured) 124 Providing and laying of pre cast RCC rings for soakage pitof dia 4 and height 7 including earth work in execution including all carriages all complete as per directions of EIC 125 P/fof pre castcement concrete slab for the soakage pitincluding all carriages all complete as per directions 126 Providing and laying of matting including cost of 10 mm thick foam including all costs complete job. 127 Providing and fixing of PVC panelling of approved pattern over and including base of 10mm thick plywood with frame work of budloo wood and finishing exposed surface with two coats of touchwood polish including cost of nails, adhesive material etc and all carriages complete. 128 Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.)Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15) 129 Providing anf fixing of 4mm thick ACP board flat pressed in panelling fixed in aluminium doors, windows shutters and partition frames with CP brass/ stainless steel screws etc complete as per drawings and directions of EIC. 130 Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge:1:3:6 or richer mix (i/c equivalent design mix) 131 Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge. 132 Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In cement mortar 133 Providing and installing heating element of gyser including all costs complete 134 Dismantling steel work manually/by mechanical means in built up sections without dismembering and stacking within 50 meters lead as per direction of Engineer-in-charge 135 Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of : G.S. Sheet 136 Providing of plastic chairs of approved brand / make 137 Providing of sofa set3+1+1 ofapproved brand with cloth lining AND TABLENOT LESS 4X 3 138 P/F of queen size bed of standard make 139 P/F of VIP/Official chair of approved brand / make 140 P/F of BEDDING INCLUDINGDUNLOP 150 MM BED SHEET QUILT , BLANKET NOT LESS THAN 5.OO KGCUSHION FOR QUEEN SIZE BED 141 P/F of Wallpapers incl. All fixtures,Complete job. 142 Supply of Utensils (All items related to daily usage), complete job. 143 P/F of Curtains,including curtains rods, all fixtures.complete job 144 Providing and fixing of LED TV24 of standard brand and manufacture , wallmount ISI marked,complete. 145 P/f of Led lights, MCBs, Sockets incl. all fixtures.Complete job. 146 Providing and fixing of ceiling/table Fans incl. all necessary fixtures complete job. 147 Providing and fixing of Dustbins (20 ltr of good quality), complete job. 148 Harpic 149 Wiper 150 Phenyl 151 Colin 152 Toilet brush 153 Jug 154 Bucket 155 Standing Mop 156 Broom (Jadhu) 157 Providing and laying chisel dressed Devri Stone of size 300x200 mmface with 150 mm depth in cement mortar 1: 6 (1 cement : 6 coarsesand) upto plinth level including curing.One face dressed -Fine chiseldressed 158 Providing and laying chisel dressed Devri Stone of size 300x200 mmface with 150 mm depth in cement mortar 1: 6 (1 cement : 6 coarsesand) upto plinth level including curing.One face dressed -Rough chiseldressed 159 Providing and fixing of .5 mm thick high rib cgi sheets roofing of approved profile as approved by the engineer incharge inc carriage of same upto site of work complete the sheets should have proctective firm of 25 microns to avoid scratches while transformation and should be supplied in single length up to 12 mtrs 160 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid 161 P/F ofCP brass fittings of standard quality and make (Jaquar or equivalent)A)Sink Mixer 162 B)Wall mixer 163 C)Health Faucet 164 P/F of First class deodar wood in planks 165 S/F of Executive table of approved make as directed by EIC,Dimensions (In Centimeters)H 74 x W 180 x D 89, Primary Material Engineered Wood Warranty 36 Months Warranty of min weight 61 Kgs 166 Chequerred terrazzo tiles 22mm thick with graded marble chips of size upto 6mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, polishing and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) Light shade using white cement 167 P/F of devri stone fine chiselled pedestal 24x24 x24 in 1:6 mix inc pointing in 1:2 mix and also moulding of the edges and top slop cornice pedestal with depressed portion to hold the wooden post as per the approved design and pattern inc cost of stones and all carriages upto site 168 P/F of ornamental type vertical posts of ist class deodar wood of approved pattern and design inc P/applying 2 or more coats of touch wood polishing etc complete size 9x9 dia 12 heigh inc all carriages complete 169 Providing and fixing kitchen sink including making all connections excluding cost of fittings : 18.26.1 White glazed fire clay sink of size 600x450x250 mm 170 Supplying, fitting and fixing 8mm thickAC4 Grade Waterproof Laminated wooden Flooring Work including cornice of required size with plank size not less than 1218mm x 193mm) mm (with unilin/tongue-groove locking arrangement) having 0.2mm thick top abrasive layer over a decorative layer followed by a High-density fibreboard (HDF) having density > 850 kg/m3 substrate core over a resin saturated backing layer and installing through unilin or tongue- groove system (having locking strength not less than 1000 kg/m) over a 2 mm thick underlayer polyurethane foam on polythene sheet 250 microns, over a smooth, flat, hard subfloor free from moisture (<8%), grease etc. complete in all respect with requisite accessories like end profile, transition profile, reducer T profile etc. wherever required and preparation of base including all other incidental works as per direction & satisfaction of Engineer in charge 171 Providing and applying Deco paint finish on approved wood or metal surfaces, including surface preparation, filling, priming, undercoating, and top coating with high-quality nitrocellulose-based Duco paint by spray application to achieve a smooth, hard, high-gloss finish as per manufacturer’s specifications and instructions of Engineer-in-Charge 172 Supplying of extension Cord for bearing load upto 4 KW