|
| 1 | Provision of Shed with necessary repairs to storm water drain in the area of proposed shed and beatification of garden near MTA Bldg. No.19 at MPF Ambernath. |
| 2 | Excavating in trenches (hard dense soil), n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out including removing balance material outside factory premises, etc all complete as directed by EIC. |
| 3 | Excavating in mud for cleaning of gutter including removing balance material outside factory premises, etc all complete as directed by EIC. |
| 4 | Demolition in Cement Concrete in ground floors and pavings n exc 15 cm thickness(below or above ground level) including removing of debris outside factory premises, etc all complete as directed by EIC. |
| 5 | M&L Hardcore Broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface and proper slope, etc all complete as directed by EIC |
| 6 | M&L Cement concrete Type B2 1:2:4 in 40 / 20 mm graded aggregate in foundations, filling and mass concrete including proper slope, formwork required and curring, etc all complete as directed by EIC |
| 7 | Providing material, fabricating errecting and painting of the structural steel parking shade to be covered with 10mm multiwall multiell polycarbonate sheet white / translucent colour ISI mark, structural steel to be provided with Finishing with hot deep galvanisation Confirming BS EN ISO1461, PU paint colour,M.S. plate 14mm thick and anchore bolt to be provided. 1) 100mm MS Pole bending round pipe ,4mm thick 2) 60 mm MS rafter 3.2mm thick3) 50mm MS purlin 2.5mm thick4) 500x200 mm MS Base Plate 14mm thick5) 50x2mm column support 6) 150x8 mm cleat7)Finishing with hot deep galvanisation Confirming BS EN ISO1461, PU paint colour8) 10mm multiwall poly carbonate sheetAll structure removable nut bolt system with PU coating, etc all complete as directed by EIC.Important Note: Structure should be designed from approved Govt. Structural Engineer at contractor\"s cost. Contractor shall get the sample approved from the Engg In Charge / Competent Factory Authority prior to commence the work |
| 8 | Providing material, fabricating erecting and painting and erection of structural steel shade to be covered with tensile fabric 750GSM white colour ISI mark. Painting on Structure steel material Fnishing with hot deep galvanisation Confirming BS EN ISO1461, PU paint colour,plates 12mm thick and anchor bolt to be provided, whole structure to be fabricated , erected with standard wire rope. 1) 75mm or 3\" bending round pipe , 10 gauge 3mm thick 2) 75mm or 3\" Supporting round pipe 12 Gauge 2.5mm thick3) 75mm or 3\" purlin round pipe 14 gauge 2mm thickAll structure removable nut bolt system with PU coating, etc all complete as directed by EIC Important Note: Structure should be designed from approved Govt. Structural Engineer at contractors cost. Contractor shall get the sample approved from the Engg In Charge / Competent Factory Authority prior to commence the work |
| 9 | M&L Cement concrete sub base flooring 100mm thick avg.type B- 2, 1:2:420 / 40 mm graded aggregate including smooth finish, proper slope, formwork required and curring, etc all complete as directed by EIC. |
| 10 | M&L Screed bed or bedding layer of mortar 15 mm thick avg in 1:6for laying floor finishesincluding proper slope, etc all complete as directed by EIC. |
| 11 | S&F Chequered cement concrete tiles 300mm x 300mm thickness as per manufacturer specification set, jointed and pointed in neat cement slurryin floors, etc all complete as directed by EICImportant Note:Contractor shall get the sample approved from the Engg In Charge / Competent Factory Authority prior to commence the work |
| 12 | S&F Glazed ceramiccolour tiles in vertical surface450X 300X 7mm thickness as per manufacturer specification, set and jointed in neat cement slurry and pointed in white or colour cement to match, etc all complete as directed by EIC.(Make: Johnson / Somany / Kajaria)Important Note:Contractor shall get the sample approved from the Engg In Charge / Competent Factory Authority prior to commence the work |
| 13 | M&L Granite 18-20mm thick(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, etc all complete as directed by EICImportant Note:Contractor shall get the sample approved from the Engg In Charge / Competent Factory Authority prior to commence the work |
| 14 | M&L Providing edge moulding to 18-20mm thick (granite) stone of counters vanities etc. including machine polishing to edge to give high gloss finish, etc all complete as directed by EIC.Important Note:Contractor shall get the sample approved from the Engg In Charge / Competent Factory Authority prior to commence the work |
| 15 | M&L Walling ofrandom rubble in CM 1:6, uncoursed well bonded, bedded and solidly hearted, etc all complete as directed by EIC |
| 16 | M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6mmean radius built in CM 1:4, etc all complete as directed by EIC |
| 17 | M&L Rendering 10mm thick cement plaster (1:4) on fair faces of brick work or concrete surfaces, etc all complete as directed by EIC |
| 18 | M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering, etc all complete as directed by EIC |
| 19 | S& F precast cement concrete cover slab (for manhole ) in Type B1 1:2:4 (20mm graded aggregate, including reinforcement set in cement mortar 1:4, etc all complete as directed by EICImportant Note:Contractor shall get the sample approved from the Engg In Charge / Competent Factory Authority prior to commence the work |
| 20 | M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, etc all complete as directed by EIC. |
| 21 | M & L for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, etc all complete as per architectural drawings and the directions of Engineer-in-charge. Important Note: Contractor shall get the sample approved of sample from the Engg In Charge / Competent Factory Authority prior to commence the work. |
| 22 | S&F Sheet glass, best quality and glazing with oil putty in square n exc 0.5 sq. m in eachpane sheet Glass 4 mm thick with ething strip or pattern, etc all complete as directed by Engg-in-Charge.(Make: Modi Guard / Saint Gobin)Important Note: Contractor shall get the sample approved of sample from the Engg In Charge / Competent Factory Authority prior to commence the work. |
| 23 | S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, etc all complete as directed by the Engg in Charge.Important Note: Contractor shall get the sample approved of sample from the Engg In Charge / Competent Factory Authority prior to commence the work. |
| 24 | M & L forNeeru finish to plastering as specified, etc all complete as directed by EIC |
