tender for Proposed Two Storied Office Building Of Dingakhola Gram Panchayat Under Dingakhola G.P.Within Shyampur - I P. Samity - Earth work in excavation of foundation trenches or drains,... as required complete Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) Single brick flat soling of picked jhama bricks Ordinary cement concrete (Mix 1:2:4) withy graded stone chips… Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) Hire & Labour charges of shuttering with centering and…etc (c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work For 1st Floor Ordinary Cement concrete (1:1.5:3) with graded stone chips…etc …for a) Ground Floor b) For 1st Floor Reinforcement for reinforced concrete work in all sorts of structures ..., placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction for Ground Floor for 1st Floor 40 mm. thick damp proof course with cement concrete (1:1.5:3) (with graded stone chips 20 mm nominal size)… Brick work 1st class bricks in cement mortar (6:1) in foundation and plinth Super structre at Groundt Floor Super structre at First Floor 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. Ground Floor 1st Floor Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] 15mm Ceiling Plaster 1:4 Gound Floor First Floor 25 mm Inside and Out side Plaster 1:6 Gound Floor First Floor Neat cement punning Supplying and laying true to line and level vitrified tiles ofapproved brand (size not less than 600 mm X 600 mm X 10mm thick) in floor…. Deep Colour & White ( A) Floor (A) Deep Colour & White First Floor Supplying fitting and fixing 15 to 18 mm thick Marble slab/Tile in riser of step or skirting (upto 300 mm ht) over 15mm (avg) thick base of Cement mortar (1:2) laid with white cement slurry @ 4.4 kg/ Sq.m at back side of marble and jointed with white cement slurry @ 2.2 kg/ Sq.m with necessary pigments including grinding and Granite Polishing. [White cement and Pigment to be supplied by the Agency] At ground Floor Slab - Area over .33 sqm for stair At First Floor Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:- ii ) 3 /4 track sliding window Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections at the rate 6.5kg/sqm Supplying bubble free float glass of approved make and brand… M.S. gate of Jail type as per approved design made of strong M.S. frame work, intermediate stiffeners and round / square bars or angles. M.S. sheet (not less than 14 gauge) gussets, cleats etc. including necessary riveting, bolting, welding, locking and hanging arrangements, fitting and fixing complete as per direction of theEngineer-in -charg Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete. M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.bars. [The extra rate admissible for the openable portion only] Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (iv) Two coats (with any shade except white) Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface ...specification and as per direction of the EIC. (In Ground Floor) Arcrylic Distemper to interior wall, ceiling with a coat of solvent based i... surface.Two Coats Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the EIC :(b) Two Coats Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturers specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all icidentalcharges but excluding the cost of primer. b) Premium 100% Acrylic Emulsion Electrical Works Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded FRPVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polyethene pipe complete with all accessories embedded in wall to light/fan/call bell points with Piano key type switch (Anchor make) fixed on sheet metal (16 SWG) switch board with Bakelite/Perspex (wall matching colour) top cover (3 mm thick) flushed in wall incl. mending good damages to original finish2x22/0.3 (Ph. & N) and 1x22/0.3 as ECC[light pts+exhaust fan pts+outdoor light pts+ceiling fan pts+tube light pts][PWD Schedule Page No-E-9;2(a)] Average run 6 Mtr Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded FR PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polyethene pipe complete with all accessories embedded in wall to 240 V 5A 3 pin plug point incl. S&F 240 V 5A 3 pin flush type plug socket & piano key type switch (Anchor make) incl. S&F earth continuity wire, fixed on sheet metal (16 SWG) switch board with Bakelite/Perspex (wall matching colour) top cover (3 mm thick) flushed in wall incl. mending good damages to original finish2x22/0.3 (Ph. & N) and 1x22/0.3 as ECC[PWD Schedule Page No-E-10; I-4(a)] On Board (only for pay counter) Supplying and Drawing 1.1 KV single core stranded FR PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required2x56/0.3 (4 sqmm) + 1x36/0.3 (2.5 sqmm) as ECC[PWD Schedule Page No-E-9 Item No-1(s)] Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection6-32A SP MCB (Make - Havells)[PWD Schedule Page No-D-6;Iteam No-7] Supplying and fixing 240/415 V MCB Isolator on din rail of existing DBs and necessary connection.63A FP MCB Isolator (Make - Havells)[PWD Schedule Page No-D-5;Iteam No-6] Supply TMC501 Conventional industrial baflen Philips LED tube, model no : TMC 501 P 1xT-LED 22 W P3241[Irrigation & Waterways/Mech Elec. Works/2022/P-113/I-5.3 F.21] Fixing only single/twin fluorescent light fitting complete with all accessories directly on wall/ceiling by screws etc.. [PWD Schedule Page No-C-2;Iteam No-14a] Supplying of different types of LED lamps (9W) Havells make, NU Bulb Plus 9 W 865 B22 3 Star[Irrigation & Waterways/Mech Elec. Works/2022/P-113/I-5.3 F.25.3] S & F Bittern Holder BakeliteMake: Anchor(PWD such - Page--K-1, I-28) Supplying & Fixing bulk head light fitting (Havells make) with die cast aluminium housing & frosted glass on wall/ceiling incl. S&F 8watt CFL / 100 watts GLS lamp complete set.. [Make - Havells](PWD Schedule - Page--D-13, I-23) Supply and delivery of Ceiling fan 48” Sweep Crompton Greaves make Supply & Fixing 240V, Modular Socket (2 Module) type fan regulator (Step type) (Brand approved by EIC) on existing Modular GI switch board with top cover plate incl. making necy. connections etc.[PWD Schedule Page No-E-18, Item No-10] Supplying & Fixing GI Modular Switch Board of the following sizes complete with three no. suitable size Copper bar with holes (for Ph, N & E) fixed on Bakelite/Hard Rubber insulator over the MS welded chairs incl. top cover flushed in wall for housing the board after cutting the brick wall incl. making earthing attachment, painting and mending good damages to building works.6 Module[PWD Schedule Page No-E-17;Iteam No-1(d)] Supplying & Fixing GI Modular Switch Board of the following sizes complete with three no. suitable size Copper bar with holes (for Ph, N & E) fixed on Bakelite/Hard Rubber insulator over the MS welded chairs incl. top cover flushed in wall for housing the board after cutting the brick wall incl. making earthing attachment, painting and mending good damages to building works.12 Module[PWD Schedule Page No-E-17;Iteam No-1(d)] S & F M.S. Fan clamps of 2 piece type of RC ceiling as per approved specification fabricated from 40mm x 9mm (11/2 x 3/8) M.S. flat incl.making good damages to building roof with satisfactory finishing and painting.[PWD Schedule Page No-D-14, Item No-29] Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod up to 30 cm incl.painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire.[PWD Schedule Page No-C-4, Item No-21(a)] Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (hot Dip) wire (4 Mts.long), 13 mm dia x 80 mm long GI bolts, double nuts,double washers incl. S&F 15 mm dia GI pipe protection (1 Mt.long)to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts.below the ground level. By ISI-Medium G.I Pipe.[PWD Schedule Page No-G-1;Iteam No-2(a)]
